Selective Separation of C8 Aromatics by an Interpenetrating Metal-Organic Framework Material

O-xylene (OX) is an important chemical raw material, but it is often produced in mixtures with other C8 aromatics. Similar physicochemical properties of the C8 isomers make their separation and purification very difficult and energy intensive. There is an unmet need for an adsorbent that would be effective for the separation of OX from the other C8 isomers. This work reports a three-dimensional interpenetrated metal-organic framework, SYUCT-110, that interacts with each of the single-component C8 isomers to form. The selectivity of C8 aromatic hydrocarbons was determined through liquid-phase batch uptake experiments. The results revealed that the selectivity order was OX > PX > MX > ethylbenzene (EB). The selectivity values were found to be 2.63, 1.58, 5.51, 3.71, 1.86, and 3.02 for OX/MX, OX/PX, OX/EB, PX/MX, MX/EB, and PX/EB, respectively. The adsorption capacity of OX was 71 mg/g. Grand Canonical Monte Carlo simulations were used to study the C8 adsorption sites, revealing that π···π interactions are the main reason for the observed adsorption selectivity. The adsorption energy calculation results also verified the selectivity of SYUCT-110 for the synthesis of OX.

Gate-opening Induced by C8 Aromatics in a Double Diamondoid Coordination Network

Coordination networks (CNs) that undergo guest-induced structural transformations are of topical interest thanks to their potential utility in separations and storage applications. Herein, we report a double diamondoid (ddi) topology CN, [Ni2(bimpz)2(bdc)2(H2O)] n or X-ddi-2-Ni (H2bdc = 1,4-benzenedicarboxylic acid, bimpz = 3,6-bis(imidazol-1-yl)pyridazine), that undergoes structural transformations induced by C8 isomers, i.e., xylenes (o-xylene, OX; m-xylene, MX; p-xylene, PX) and ethylbenzene (EB). X-ddi-2-Ni was characterized by single-crystal to single-crystal transformations from a nonporous phase, X-ddi-2-Ni-β, to isostructural C8-loaded phases, namely X-ddi-2-Ni-OX, X-ddi-2-Ni-MX, X-ddi-2-Ni-PX and X-ddi-2-Ni-EB. X-ddi-2-Ni accommodates two C8 isomers per Ni unit, resulting in relatively high uptake (ca. 50 wt %), but with low selectivity toward C8 isomers as found using nuclear magnetic resonance (NMR) and gas chromatography (GC). In addition, a narrow range of gate-opening pressures for each isomer was determined from dynamic vapor sorption, consistent with the nonadaptable nature of the C8-loaded phase determined crystallographically, also supported by modeling.

Effect of Polymorphism on the Sorption Properties of a Flexible Square-Lattice Topology Coordination Network

The stimulus-responsive behavior of coordination networks (CNs), which switch between closed (nonporous) and open (porous) phases, is of interest because of its potential utility in gas storage and separation. Herein, we report two polymorphs of a new square-lattice (sql) topology CN, X-sql-1-Cu, of formula [Cu(Imibz)2]n (HImibz = {[4-(1H-imidazol-1-yl)phenylimino]methyl}benzoic acid), isolated from the as-synthesized CN X-sql-1-Cu-(MeOH)2·2MeOH, which subsequently transformed to a narrow pore solvate, X-sql-1-Cu-A·MeOH, upon mild activation (drying in air or heating at 333 K under nitrogen). X-sql-1-Cu-A·MeOH contains MeOH in cavities, which was removed through exposure to vacuum for 2 h, yielding the nonporous (closed) phase X-sql-1-Cu-A. In contrast, a more dense polymorph, X-sql-1-Cu-B, was obtained by exposing X-sql-1-Cu-(MeOH)2·2MeOH directly to vacuum for 2 h. Gas sorption studies conducted on X-sql-1-Cu-A and X-sql-1-Cu-B revealed different switching behaviors to two open phases (X-sql-1-Cu·CO2 and X-sql-1-Cu·C2H2), with different gate-opening threshold pressures for CO2 at 195 K and C2H2 at 278 K. Coincident CO2 sorption and in situ powder X-ray diffraction studies at 195 K revealed that X-sql-1-Cu-A transformed to X-sql-1-Cu-B after the first sorption cycle and that the CO2-induced switching transformation was thereafter reversible. The results presented herein provide insights into the relationship between two polymorphs of a CN and the effect of polymorphism upon gas sorption properties. To the best of our knowledge, whereas sql networks such as X-sql-1-Cu are widely studied in terms of their structural and sorption properties, this study represents only the second example of an in-depth study of the sorption properties of polymorphic sql networks.

Insight into the Gas-Induced Phase Transformations in a 2D Switching Coordination Network via Coincident Gas Sorption and In Situ PXRD

Switching coordination networks (CNs) that reversibly transform between narrow or closed pore (cp) and large pore (lp) phases, though fewer than their rigid counterparts, offer opportunities for sorption-related applications. However, their structural transformations and switching mechanisms remain underexplored at the molecular level. In this study, we conducted a systematic investigation into a 2D switching CN, [Ni(bpy)2(NCS)2]n, sql-1-Ni-NCS (1 = bpy = 4,4'-bipyridine), using coincident gas sorption and in situ powder X-ray diffraction (PXRD) under low-temperature conditions. Gas adsorption measurements revealed that C2H4 (169 K) and C2H6 (185 K) exhibited single-step type F-IVs sorption isotherms with sorption uptakes of around 180-185 cm3 g-1, equivalent to four sorbate molecules per formula unit. Furthermore, parallel in situ PXRD experiments provided insight into sorbate-dependent phase switching during the sorption process. Specifically, CO2 sorption induced single-step phase switching (path I) solely between cp and lp phases consistent with the observed single-step type F-IVs sorption isotherm. By contrast, intermediate pore (ip) phases emerged during C2H4 and C2H6 desorption as well as C3H6 adsorption, although they remained undetectable in the sorption isotherms. To our knowledge, such a cp-lp-ip-cp transformation (path II) induced by C2H4/6 and accompanied by single-step type F-IVs sorption isotherms represents a novel type of phase transition mechanism in switching CNs. By virtue of Rietveld refinements and molecular simulations, we elucidated that the phase transformations are governed by cooperative local and global structural changes involving NCS- ligand reorientation, bpy ligand twist and rotation, cavity edge (Ni-bpy-Ni) deformation, and interlayer expansion and sliding.

Molecular Dynamics Simulation of the Adsorption and Diffusion of C8 Aromatic Isomers in MIL-47(V)

The separation of C8 aromatic isomers (oX: o-xylene, pX: p-xylene, mX: m-xylene, and EB: ethylbenzene) remains an enormous challenge in industrial production due to their similar molecular structures and physical properties. Porous materials with suitable pore structures and selective recognition sites to discriminate the slight structural differences of isomers are imminently needed. In this paper, MIL-47(V) with a three-dimensional (3D) grid structure of 10.5 × 10.5 Å2 and a one-dimensional (1D) diamond channel was selected as the adsorbent. However, the mechanism of the adsorption and separation of C8 aromatic isomers in porous materials still needs to be understood. Given the importance of C8 aromatic isomers' confinement in MIL-47(V) for adsorption and diffusion applications, it is important to understand C8 aromatic isomers' behavior in MIL-47(V). Here, we demonstrated from a simulation perspective that metal-organic frameworks MIL-47(V) with one-dimensional (1D) diamond channels can identify C8 aromatic isomers. Molecular dynamics (MD) simulations have shown that organic ligands with guest response sites of MIL-47(V) can effectively distinguish between C8 aromatic isomers by adaptation to the shape of a specific isomer. MIL-47(V) has high adsorption and an excellent separation sequence between C8 aromatic isomers: oX > pX ≈ mX > EB. Significant differences exist in π-π superposition interactions between C8 aromatic isomers and between C8 aromatic isomers and the skeletons. This phenomenon is mainly caused by the unique pore structure and guest response characteristics of MIL-47(V). This work is identified as a supplementary instruction to experimental research and is expected to provide profound insights into research on developing C8 aromatic isomers' adsorption and separation and theoretical support.

Highly Selective p-Xylene Separation from Mixtures of C8 Aromatics by a Nonporous Molecular Apohost

High and increasing production of separation of C8 aromatic isomers demands the development of purification methods that are efficient, scalable, and inexpensive, especially for p-xylene, PX, the largest volume C8 commodity. Herein, we report that 4-(1H-1,2,4-triazol-1-yl)-phenyl-1H-benzo[de]isoquinoline-1,3(2H)-dione (TPBD), a molecular compound that can be prepared and scaled up via solid-state synthesis, exhibits exceptional PX selectivity over each of the other C8 isomers, o-xylene (OX), m-xylene (MX), and ethylbenzene (EB). The apohost or α form of TPBD was found to exhibit conformational polymorphism in the solid state enabled by rotation of its triazole and benzene rings. TPBD-αI and TPBD-αII are nonporous polymorphs that transformed to the same PX inclusion compound, TPBD-PX, upon contact with liquid PX. TPBD enabled highly selective capture of PX, as established by competitive slurry experiments involving various molar ratios in binary, ternary, and quaternary mixtures of C8 aromatics. Binary selectivity values for PX as determined by 1H NMR spectroscopy and gas chromatography ranged from 22.4 to 108.4, setting new benchmarks for both PX/MX (70.3) and PX/EB (59.9) selectivity as well as close to benchmark selectivity for PX/OX (108.4). To our knowledge, TPBD is the first material of any class to exhibit such high across-the-board PX selectivity from quaternary mixtures of C8 aromatics under ambient conditions. Crystallographic and computational studies provide structural insight into the PX binding site in TPBD-PX, whereas thermal stability and capture kinetics were determined by variable-temperature powder X-ray diffraction and slurry tests, respectively. That TPBD offers benchmark PX selectivity and facile recyclability makes it a prototypal molecular compound for PX purification or capture under ambient conditions.

Switching Adsorbent Layered Material that Enables Stepwise Capture of C8 Aromatics via Single-Crystal-to-Single-Crystal Transformations

Separation of the C8 aromatic isomers, xylenes (PX, MX, and OX) and ethylbenzene (EB), is important to the petrochemical industry. Whereas physisorptive separation is an energy-efficient alternative to current processes, such as distillation, physisorbents do not generally exhibit strong C8 selectivity. Herein, we report the mixed-linker square lattice (sql) coordination network [Zn2(sba)2(bis)]n·mDMF (sql-4,5-Zn, H2sba or 4 = 4,4'-sulfonyldibenzoic acid, bis or 5 = trans-4,4'-bis(1-imidazolyl)stilbene) and its C8 sorption properties. sql-4,5-Zn was found to exhibit high uptake capacity for liquid C8 aromatics (∼20.2 wt %), and to the best of our knowledge, it is the first sorbent to exhibit selectivity for PX, EB, and MX over OX for binary, ternary, and quaternary mixtures from gas chromatography. Single-crystal structures of narrow-pore, intermediate-pore, and large-pore phases provided insight into the phase transformations, which were enabled by flexibility of the linker ligands and changes in the square grid geometry and interlayer distances. This work adds to the library of two-dimensional coordination networks that exhibit high uptake, thanks to clay-like expansion, and strong selectivity, thanks to shape-selective binding sites, for C8 isomers.

The Effect of Pendent Groups upon Flexibility in Coordination Networks with Square Lattice Topology

Gas or vapor-induced phase transformations in flexible coordination networks (CNs) offer the potential to exceed the performance of their rigid counterparts for separation and storage applications. However, whereas ligand modification has been used to alter the properties of such stimulus-responsive materials, they remain understudied compared with their rigid counterparts. Here, we report that a family of Zn2+ CNs with square lattice (sql) topology, differing only through the substituents attached to a linker, exhibit variable flexibility. Structural and CO2 sorption studies on the sql networks, [Zn(5-Ria)(bphy)]n, ia = isophthalic acid, bphy = 1,2-bis(pyridin-4-yl)hydrazine, R = -CH3, -OCH3, -C(CH3)3, -N=N-Ph, and -N=N-Ph(CH3)2, 2-6, respectively, revealed that the substituent moieties influenced both structural and gas sorption properties. Whereas 2-3 exhibited rigidity, 4, 5, and 6 exhibited reversible transformation from small pore to large pore phases. Overall, the insight into the profound effect of pendent moieties of linkers upon phase transformations in this family of layered CNs should be transferable to other CN classes.

Potential of nonporous adaptive crystals for hydrocarbon separation

Hydrocarbon separation is an important process in the field of petrochemical industry, which provides a variety of raw materials for industrial production and a strong support for the development of national economy. However, traditional separation processes involve huge energy consumption. Adsorptive separation based on nonporous adaptive crystal (NAC) materials is considered as an attractive green alternative to traditional energy-intensive separation technologies due to its advantages of low energy consumption, high chemical and thermal stability, excellent selective adsorption and separation performance, and outstanding recyclability. Considering the exceptional potential of NAC materials for hydrocarbon separation, this review comprehensively summarizes recent advances in various supramolecular host-based NACs. Moreover, the current challenges and future directions are illustrated in detail. It is expected that this review will provide useful and timely references for researchers in this area. Based on a large number of state-of-the-art studies, the review will definitely advance the development of NAC materials for hydrocarbon separation and stimulate more interesting studies in related fields.

Pressure-Induced Structural Effects in the Square Lattice () Topology Coordination Network Sql-1-Co-NCS·4OX

A high-pressure study of a switching coordination network of square lattice topology (sql) loaded with o-xylene (OX), [Co(4,4'-bipyridine)₂(NCS)₂] _n ·4nC₈H₁₀ (sql-1-Co-NCS·4OX), was conducted up to approximately 1 GPa to investigate pressure-induced structural changes. Previous reports revealed that sql-1-Co-NCS exhibits multiple phases thanks to its ability to switch between closed (nonporous) and several open (porous) phases in the presence of various gases, vapors, and liquids. Networks of such properties are of topical interest because they can offer high working capacity and improved recyclability for gas adsorption. The monoclinic crystal structure of sql-1-Co-NCS·4OX at 100 K was previously reported to show an increase in interlayer separation of more than 100% compared to the corresponding closed phase, sql-1-Co-NCS, when exposed to gases or vapors under ambient conditions. Herein, a tetragonal crystal form of sql-1-Co-NCS·4OX (space group I4/mmm, Phase I) that exists at 0.1 MPa/303 K is reported. Exposure of Phase I to high pressure using penetrable pressure transmitting media (OX and 1:1 vol MeOH/EtOH) did not result in further separation of the sql networks. Rather, compression of the crystals and release of adsorbed OX molecules occurred. These pressure-induced changes are discussed in terms of structural voids, framework conformation, and molecular packing of the sql layers. Although Phase I retained tetragonal symmetry throughout the investigated pressure range, the interlayer voids occupied by OX molecules were significantly reduced between 0.3 and 0.5 GPa; further compression above 0.5 GPa induced structural disorder. Additionally, analysis of the electron count present in the pores of sql-1-Co-NCS confirmed the multistep evacuation of OX molecules from the crystal, and two intermediate phases, Ia and Ib, differing in the OX loading level, are postulated.

Reversible transformations between the non-porous phases of a flexible coordination network enabled by transient porosity

Flexible metal-organic materials that exhibit stimulus-responsive switching between closed (non-porous) and open (porous) structures induced by gas molecules are of potential utility in gas storage and separation. Such behaviour is currently limited to a few dozen physisorbents that typically switch through a breathing mechanism requiring structural contortions. Here we show a clathrate (non-porous) coordination network that undergoes gas-induced switching between multiple non-porous phases through transient porosity, which involves the diffusion of guests between discrete voids through intra-network distortions. This material is synthesized as a clathrate phase with solvent-filled cavities; evacuation affords a single-crystal to single-crystal transformation to a phase with smaller cavities. At 298 K, carbon dioxide, acetylene, ethylene and ethane induce reversible switching between guest-free and gas-loaded clathrate phases. For carbon dioxide and acetylene at cryogenic temperatures, phases showing progressively higher loadings were observed and characterized using in situ X-ray diffraction, and the mechanism of diffusion was computationally elucidated.

Adsorbate-dependent phase switching in the square lattice topology coordination network [Ni(4,4'-bipyridine)2(NCS)2]n

Switching coordination networks (CNs) featuring stepped sorption isotherms that are accompanied by phase changes offer promise for gas storage and separation applications. However, their responsiveness to different adsorbates remains largely understudied. Herein, we report the variable switching behaviour of a previously known square lattice (sql) topology CN, [Ni(4,4'-bipyridine)₂(NCS)₂] (sql-1-Ni-NCS), with respect to nine gaseous adsorbates.

Isomer recognition by dynamic guest-adaptive ligand rotation in a metal-organic framework with local flexibility

Local flexibility in a metal-organic framework is intriguing for reconstructing a microenvironment to distinguish different guest molecules by emphasizing their differences. Herein, guest-adaptive flexibility is observed in a metal-organic framework for efficiently discriminating aromatic isomers. Microcrystal electron diffraction directly reveals that the anthracene rings can rotate around the single bond with the adsorption of guest molecules. Disorder transformation of the ligand enables the preferential adsorption of ethylbenzene over other xylene isomers. Especially, a coated capillary column combining single/multi-component adsorption confirms a unique separation order of ethylbenzene > p-xylene > m-xylene > o-xylene with excellent selectivities, which has not been reported in other materials. Density functional theory calculations and the calculated Hirshfeld surface of guest molecules in the framework demonstrate that a guest-induced splint-like confinement structure makes the main contribution to such separation performance. This finding will provide a rational strategy for molecular recognition utilizing the local flexibility of metal-organic frameworks.

Discrimination of xylene isomers in a stacked coordination polymer

The separation and purification of xylene isomers is an industrially important but challenging process. Developing highly efficient adsorbents is crucial for the implementation of simulated moving bed technology for industrial separation of these isomers. Herein, we report a stacked one-dimensional coordination polymer {[Mn(dhbq)(H 2 O) 2 ], H 2 dhbq = 2,5-dihydroxy-1,4-benzoquinone} that exhibits an ideal molecular recognition and sieving of xylene isomers. Its distinct temperature-adsorbate–dependent adsorption behavior enables full separation of p -, m -, and o -xylene isomers in both vapor and liquid phases. The delicate stimuli-responsive swelling of the structure imparts this porous material with exceptionally high flexibility and stability, well-balanced adsorption capacity, high selectivity, and fast kinetics at conditions mimicking industrial settings. This study may offer an alternative approach for energy-efficient and adsorption-based industrial xylene separation and purification processes.

An Adaptive Hydrogen-Bonded Organic Framework for the Exclusive Recognition of p-Xylene

Separation of xylene isomers is one of the most important but most challenging and energy-intensive separation processes in the petrochemical industry. Here, we report an adaptive hydrogen-bonded organic framework (HOF-29) constructed from a porphyrin based organic building block 4,4',4'',4'''-(porphyrin-5,10,15,20-tetrayl) tetrabenzonitrile (PTTBN), exhibiting the exclusive molecular recognition of p-xylene (pX) over its isomers of o-xylene (oX) and m-xylene (mX), as clearly demonstrated in the single crystal structure transformation and ¹ H NMR studies. Single crystal structure studies show that single-crystal-to-single-crystal transformation from the as-synthesized HOF-29 to the pX exclusively included HOF-29⊃pX is triggered by the encapsulation of pX molecules, accompanied by sliding of the 2D layers and local distortion of the ligand, which provides multiple C-H⋅⋅⋅π interactions.

Acetylene storage performance of [Ni(4,4'-bipyridine)2(NCS)2]n, a switching square lattice coordination network

We report that the previously reported square lattice coordination network [Ni(4,4'-bipyridine)₂(NCS)₂]_n, sql-1-Ni-NCS, undergoes acetylene induced switching between closed (nonporous) and open (porous) phases. The resulting stepped sorption isotherms exhibit temperature controlled steps, consistent high uptake and benchmark working capacity (185 cm^-3 g^-1 or 189 cm^-3, 1-3.2 bar, 288 K) for acetylene storage.

Rigidified Cavitand Hosts in Water: Bent Guests, Shape Selectivity, and Encapsulation

We report the synthesis and characterization of two water-soluble container compounds (cavitand hosts) with rigidified open ends. One cavitand uses four (CH₂)₄'s as spacers to bridge the adjacent walls, while another cavitand uses four CH₂CH₂OCH₂CH₂'s bridges and features a wider open end. The spacers preorganize the deep cavitands into vase-like, receptive shapes and prevent their unfolding to the unreceptive kite-like conformation. Cycloalkane guests (C6-C8) and small n-alkanes (C5-C7) form 1:1 complexes with the cavitands and move freely in the cavitands' spaces. Hydrophilic compounds 1,4-dioxane, tetrahydrofuran, tetrahydropyran, pyridine, and 1-methylimidazole also showed good binding affinity to the new cavitands. Longer alkanes (C11-C14) and n-alcohols (C11-C16) are taken up with a -CH₃ group fixed at the bottom of the cavity and the groups near the rim in compressed conformations. The methylene bridges appear to divide the cavitand into a narrow hydrophobic compartment and a broader space with exposure to the aqueous medium. Longer alkane guests (C15-C18), N,N-dimethyldioctylammonium, and dioctylamine induce the formation of capsules (2:1 host:guest complexes). The new cavitands showed selectivity for p/m-cresol isomers and xylene isomers. The cavitand with CH₂CH₂OCH₂CH₂ bridges bound long-chain α,ω-diols (C13-C15) and diamines in folded, U-shaped conformations with polar functions exposed to the aqueous medium. It was used to separate o-xylene from its isomers by using simple extraction procedures.

Xylene Recognition in Flexible Porous Coordination Polymer by Guest-Dependent Structural Transition

Xylene isomers are crucial chemical intermediates in great demand worldwide; the almost identical physicochemical properties render their current separation approach energy consuming. In this study, we utilized the soft porous coordination polymer (PCP)'s isomer-specific structural transformation, realizing o-xylene (oX) recognition/separation from the binary and ternary isomer mixtures. This PCP has a flexible structure that contains flexible aromatic pendant groups, which both work as recognition sites and induce structural flexibility of the global framework. The PCP exhibits guest-triggered "breathing"-type structural changes, which are accompanied by the rearrangement of the intraframework π-π interaction. By rebuilding π-π stacking with isomer species, the PCP discriminated oX from the other isomers by its specific guest-loading configuration and separated oX from the isomer mixture via selective adsorption. The xylene-selective property of the PCP is dependent on the solvent; in diluted hexane solution, the PCP favors p-xylene (pX) uptake. The separation results combined with crystallographic analyses revealed the effect of the isomer selectivity of the PCP on xylene isomer separation via structural transition and demonstrated its potential as a versatile selective adsorptive medium for challenging separations.

Spiers Memorial Lecture: Coordination networks that switch between nonporous and porous structures: an emerging class of soft porous crystals

Coordination networks (CNs) are a class of (usually) crystalline solids typically comprised of metal ions or cluster nodes linked into 2 or 3 dimensions by organic and/or inorganic linker ligands. Whereas CNs tend to exhibit rigid structures and permanent porosity as exemplified by most metal-organic frameworks, MOFs, there exists a small but growing class of CNs that can undergo extreme, reversible structural transformation(s) when exposed to gases, vapours or liquids. These "soft" or "stimuli-responsive" CNs were introduced two decades ago and are attracting increasing attention thanks to two features: the amenability of CNs to design from first principles, thereby enabling crystal engineering of families of related CNs; and the potential utility of soft CNs for adsorptive storage and separation. A small but growing subset of soft CNs exhibit reversible phase transformations between nonporous (closed) and porous (open) structures. These "switching CNs" are distinguished by stepped sorption isotherms coincident with phase transformation and, perhaps counterintuitively, they can exhibit benchmark properties with respect to working capacity (storage) and selectivity (separation). This review addresses fundamental and applied aspects of switching CNs through surveying their sorption properties, analysing the structural transformations that enable switching, discussing structure-function relationships and presenting design principles for crystal engineering of the next generation of switching CNs.

Reversible single-crystal to single-crystal phase transformation between a new Werner clathrate and its apohost

In this work, we report the synthesis and structural characterisation of the ligand 2-(pyridin-3-yl)-benzo[de]isoquinoline-1,3(2H)-dione, 5, its isostructural Werner complexes ML4(NCS)2 (L = 5; M = Co(II) and Ni(II)), and five clathrates with three aromatic guests, ML4(NCS)2·2G (M = Co(II) and Ni(II), G = nitrobenzene (NB); M = Co, G = 1,2-dichlorobenzene (1,2-DCB); M = Co(II) and Ni(II), G = o-xylene (OX)). 5 was prepared in high yield by condensation in the solid-state (C3S3, Cocrystal Controlled Solid-State Synthesis). The Werner complexes ML4(NCS)2 (M = Co(II) and Ni(II)) (apohosts) were prepared by reacting M(NCS)2 (M = Co(II) and Ni(II)) and 5 in 1-butanol at 60 °C for 24 h. The Werner clathrates were prepared by reacting M(NCS)2 (M = Co(II) and Ni(II)), G and 5 in 1-butanol at 60 °C for 48-96 h. The clathrates were observed to transform to the apohost ML4(NCS)2 upon heating. CoL4(NCS)2·2NB was subsequently regenerated by exposing CoL4(NCS)2 to liquid NB at 60 °C for 48 h. This phase change occurred as a single-crystal to single-crystal phase transformation and was studied by single crystal X-ray diffraction, powder X-ray diffraction and thermal analyses. Structural analyses of the apohost CoL4(NCS)2 and its Werner clathrate CoL4(NCS)2·2NB indicated that rotational freedom of the Co-N bonds together with torsional flexibility of the ligand between the imide bond and the pyridine moiety are key to enabling the structural switching induced by exposure to NB or its removal.

Molecular recognition and adsorptive separation of m-xylene by trianglimine crystals

The separation of xylene isomers is one of the most challenging tasks in the petrochemical industry. Herein, we developed an efficient adsorptive molecular sieving strategy using crystalline trianglimine macrocycle (1) to separate the elusive m-xylene isomer from an equimolar xylenes mixture with over 91% purity. The selectivity is attributed to the capture of the preferred guest with size/shape selectivity and C-H⋯π interactions. Moreover, the trianglimine crystals are readily recyclable due to the reversible transformation between the guest-free and guest-loaded structures.

High Working Capacity Acetylene Storage at Ambient Temperature Enabled by a Switching Adsorbent Layered Material

Unlike most gases, acetylene storage is a challenge because of its inherent pressure sensitivity. Herein, a square lattice (sql) coordination network [Cu(4,4'-bipyridine)₂(BF₄)₂]_n (sql-1-Cu-BF₄) is investigated with respect to its C₂H₂ sorption behavior from 189 to 298 K. The C₂H₂ sorption studies revealed that sql-1-Cu-BF₄ exhibits multistep isotherms that are temperature-dependent and consistent with the transformation from "closed" (nonporous) to four "open" (porous) phases induced by the C₂H₂ uptake. The Clausius-Clapeyron equation was used to calculate the performance of sql-1-Cu-BF₄ for C₂H₂ storage at pressures >1 bar, which revealed that its volumetric working capacity at 288 K is slightly superior to acetone (174 vs 170 cm³ cm^-3) over a safer pressure range (1-3.5 vs 1-15 bar). Molecular simulations provided insights into the observed switching phenomena, revealing that the layer expansion of sql-1-Cu-BF₄ occurs via intercalation and inclusion of C₂H₂. These results indicate that switching adsorbent layered materials offer promise for utility in the context of C₂H₂ storage and delivery.

Separation of Xylene Isomers in the Anion-Pillared Square Grid Material SIFSIX-1-Cu

Xylene isomer separation is considered one of the seven separation challenges that changed the world. In addition, the high-energy demand of xylene separation highlights the need for efficient novel adsorbents. Herein, the liquid-phase separation potential of the anion-pillared hybrid material SIFSIX-1-Cu was studied for preferential adsorption of o-xylene and m-xylene over p-xylene, which was inspired by a previous complexation crystallization method for separating m-xylene. We report detailed experimental liquid-phase adsorption experiments, yielding selectivities of 3.0 for o-xylene versus p-xylene and 2.6 for m-xylene versus p-xylene. Our theoretical calculations thus provide a reasonable explanation that the xylene adsorption selectivity is attributed to the C-H⋅⋅⋅F interaction, and the host-guest interaction order agrees with the adsorption priority: o-xylene > m-xylene > p-xylene.

Metal-Organic Frameworks for Highly Selective Separation of Xylene Isomers and Single-Crystal X-ray Study of Aromatic Guest-Host Inclusion Compounds

Separation of hydrocarbon molecules, such as benzene/cyclohexane and o-xylene/m-xylene/p-xylene, is relevant due to their widespread application as chemical feedstock but challenging because of their similar boiling points and close molecular sizes. Physisorption separation could offer an energy-efficient solution to this problem, but the design and synthesis of sorbents that exhibit high selectivity for one of the hydrocarbons remain a largely unmet challenge. Herein, we report a new heterometallic MOF with a unique tortuous shape of channels decorated with aromatic sorption sites [Li₂Zn₂(bpy)(ndc)₃] (NIIC-30(Ph), bpy = 4,4'-bipyridine, ndc^2- = naphthalene-1,4-dicarboxylate) and study of its benzene/cyclohexane and xylene vapor and liquid separation. For an equimolar benzene/cyclohexane mixture, it is possible to achieve a 10-fold excess of benzene in the adsorbed phase. In the case of xylenes, microporous framework NIIC-30(Ph) demonstrates outstanding selective sorption properties and becomes a new benchmark for m-/o-xylene separation. In addition, NIIC-30(Ph) is stable enough to carry out at least three separation cycles of benzene/cyclohexane mixtures or ternary o-xylene/m-xylene/p-xylene mixtures both in the liquid and in the vapor phase. Insights into the performance of NIIC-30(Ph) are gained from X-ray structural studies of each aromatic guest inclusion compound.

Tailoring the Pore Size and Chemistry of Ionic Ultramicroporous Polymers for Trace Sulfur Dioxide Capture with High Capacity and Selectivity

Here we demonstrate the deep removal of SO₂ with high uptake capacity (1.55 mmol g^-1 ) and record SO₂ /CO₂ selectivity (>5000) at ultra-low pressure of 0.002 bar, using ionic ultramicroporous polymers (IUPs) with high density of basic anions. The successful construction of uniform ultramicropores via polymerizing ionic monomers into IUPs enables the fully exploitation of the selective anionic sites. Notably, the aperture size and surface chemistry of IUPs can be finely tuned by adjusting the branched structure of ionic monomers, which play critical roles in excluding CH₄ and N₂ , as well as reducing the coadsorption of CO₂ . The swelling property of IUPs with adsorption of SO₂ contributed to the high SO₂ uptake capacity and high separation selectivity. Systematic investigations including static gas adsorption, dynamic breakthrough experiments, stability tests and modeling studies confirmed the efficient performance of IUPs for trace SO₂ capture.

Simultaneous interlayer and intralayer space control in two-dimensional metal-organic frameworks for acetylene/ethylene separation

Three-dimensional metal−organic frameworks (MOFs) are cutting-edge materials in the adsorptive removal of trace gases due to the availability of abundant pores with specific chemistry. However, the development of ideal adsorbents combining high adsorption capacity with high selectivity and stability remains challenging. Here we demonstrate a strategy to design adsorbents that utilizes the tunability of interlayer and intralayer space of two-dimensional fluorinated MOFs for capturing acetylene from ethylene. Validated by X-ray diffraction and modeling, a systematic variation of linker atom oxidation state enables fine regulation of layer stacking pattern and linker conformation, which affords a strong interlayer trapping of molecules along with cooperative intralayer binding. The resultant robust materials (ZUL-100 and ZUL-200) exhibit benchmark capacity in the pressure range of 0.001–0.05 bar with high selectivity. Their efficiency in acetylene/ethylene separation is confirmed by breakthrough experiments, giving excellent ethylene productivities (121 mmol/g from 1/99 mixture, 99.9999%), even when cycled under moist conditions.

Designing efficient adsorbents for trace gas removal remains a serious challenge. Here, the authors show promise in layered 2D metal−organic frameworks, often overlooked in favor of 3D frameworks, for separating trace acetylene from ethylene with enhanced performance and high stability.

Efficient separation of xylene isomers by a guest-responsive metal-organic framework with rotational anionic sites

The separation of xylene isomers (para-, meta-, orth-) remains a great challenge in the petrochemical industry due to their similar molecular structure and physical properties. Porous materials with sensitive nanospace and selective binding sites for discriminating the subtle structural difference of isomers are urgently needed. Here, we demonstrate the adaptively molecular discrimination of xylene isomers by employing a NbOF₅²⁻-pillared metal–organic framework (NbOFFIVE-bpy-Ni, also referred to as ZU-61) with rotational anionic sites. Single crystal X-ray diffraction studies indicate that ZU-61 with guest-responsive nanospace/sites can adapt the shape of specific isomers through geometric deformation and/or the rotation of fluorine atoms in anionic sites, thereby enabling ZU-61 to effectively differentiate xylene isomers through multiple C–H···F interactions. ZU-61 exhibited both high meta-xylene uptake capacity (3.4 mmol g⁻¹) and meta-xylene/para-xylene separation selectivity (2.9, obtained from breakthrough curves), as well as a favorable separation sequence as confirmed by breakthrough experiments: para-xylene elute first with high-purity (≥99.9%), then meta-xylene, and orth-xylene. Such a remarkable performance of ZU-61 can be attributed to the type anionic binding sites together with its guest-response properties.

The separation of xylene isomers remains a great challenge in industry due to their similar molecular structure and physical properties. Here the authors demonstrate adaptively molecular discrimination of xylene isomers by employing a NbOF₅²⁻-pillared metal–organic framework with rotational anionic sites.

Crystal engineering of a rectangular coordination network to enable xylenes selectivity over ethylbenzene

Separation of the C8 aromatic isomers, p-xylene (PX), m-xylene (MX), o-xylene (OX) and ethylbenzene (EB), is relevant thanks to their widespread application as chemical feedstocks but challenging because of their similar boiling points and close molecular dimensions. Physisorptive separation could offer an energy-efficient solution to this challenge but sorbents which exhibit strong selectivity for one of the isomers remain a largely unmet challenge despite recent reports of OX or PX selective sorbents with high uptake capacity. For example, the square lattice, sql, topology coordination network [Co(bipy)2(NCS)2] n (sql-1-Co-NCS) exhibits the rare combination of high OX selectivity and high uptake capacity. Herein we report that a crystal engineering approach enabled isolation of the mixed-linker sql coordination network [Co(bipy)(bptz)(NCS)2] n (sql-1,3-Co-NCS, bipy = 4,4'-bipyridine, bptz = 4,4'-bis(4-pyridyl)tetrazine) and study of its C8 vapour and liquid sorption properties. sql-1,3-Co-NCS was found to exhibit high adsorption capacity from liquid xylenes (∼37 wt%) and is to our knowledge the first sorbent to exhibit high selectivity for each of xylene isomer over EB (S OX/EB, S MX/EB, S PX/EB > 5). Insights into the performance of sql-1,3-Co-NCS are gained from structural studies which reveal stacking interactions between electron-deficient bptz linkers and the respective xylenes. sql-1,3-Co-NCS is the first N-donor mixed-linker sql coordination network studied for its gas/vapour sorption properties and represents a large and diverse class of understudied coordination networks.

Binding selectivity and separation of p-functionalized toluenes with a metallo-cavitand in water

A metallo-cavitand (1-2Pd) showed unprecedented binding selectivity and sequestration of p-functionalized toluene isomers in water. The host-guest complexation was studied using 1H and COSY NMR methods and xylene-isomer complexes were examined by using DFT calculations. A liquid-liquid extraction scheme was developed for the separation of p-functionalized toluenes.

Reversible Switching between Nonporous and Porous Phases of a New SIFSIX Coordination Network Induced by a Flexible Linker Ligand

Closed-to-open structural transformations in flexible coordination networks are of potential utility in gas storage and separation. Herein, we report the first example of a flexible SiF₆^2--pillared square grid material, [Cu(SiF₆)(L)₂]_n (L = 1,4-bis(1-imidazolyl)benzene), SIFSIX-23-Cu. SIFSIX-23-Cu exhibits reversible switching between nonporous (β1) and several porous (α, γ1, γ2, and γ3) phases triggered by exposure to N₂, CO₂, or H₂O. In addition, heating β1 to 433 K resulted in irreversible transformation to a closed polymorph, β2. Single-crystal X-ray diffraction studies revealed that the phase transformations are enabled by rotation and geometrical contortion of L. Density functional theory calculations indicated that L exhibits a low barrier to rotation (as low as 8 kJmol^-1) and a rather flat energy surface. In situ neutron powder diffraction studies provided further insight into these sorbate-induced phase changes. SIFSIX-23-Cu combines stability in water for over a year, high CO₂ uptake (ca. 216 cm³/g at 195 K), and good thermal stability.

Construction and selective gas adsorption properties of two heteroSBU MOFs based on unsymmetrical tetracarboxylate linkers

Two homometallic pure-carboxylate hetero-SBU MOFs were constructed, displaying selective C₂H₂/CH₄ and CO₂/CH₄ separation potential.

Energy-efficient separation alternatives: metal–organic frameworks and membranes for hydrocarbon separation

The diversity of metal–organic frameworks enables the design of highly efficient adsorbents and membranes towards hydrocarbon separations for energy consumption mitigation.

[Cu(4-phenylpyridine)4(trifluoromethanesulfonate)2], a Werner complex that exhibits high selectivity for o-xylene

A new Werner complex features a switching sorption isotherm for o-xylene and combines high o-xylene selectivity with high uptake.

Immobilization of N-oxide functionality into NbO-type MOFs for significantly enhanced C2H2/CH4 and CO2/CH4 separations

Two NbO-type MOFs with N-oxide functionality immobilized in the pore surface display significantly enhanced C₂H₂/CH₄ and CO₂/CH₄ separation performance.

Control of local flexibility towards p-xylene sieving in Hofmann-type porous coordination polymers

Tuning of local flexibility towards p-xylene achieved by the control of the specific combination of coordination metal centers in Hofmann-type porous coordination polymers.

Benchmark selectivity p-xylene separation by a non-porous molecular solid through liquid or vapor extraction

Solid-liquid separation of similarly sized organic molecules utilizing sorbents offers the potential for new energy-efficient approaches to a number of important industrial separations such as xylenes (C8) separations. Research on selective C8 sorption has tended to focus upon rigid porous materials such as zeolites and MOFs but has revealed generally weak selectivity that is inconsistent across the range of C8 molecules. Nevertheless, there are a few recent examples of non-porous molecular materials that exhibit relatively high selectivity for p-xylene (pX) from pX/oX, approaching that of the current benchmark pX sorbent, the zeolite H/ZSM-5. Herein, we report that a L-shaped Ag(i) complex, AgLClO4 (M), which crystallizes as a non-porous molecular solid material, offering exceptional performance for pX selectivity across the range of C8 isomers with liquid extraction selectivity values of 24.0, 10.4 and 6.2 vs. oX, eB and mX, respectively. The pX selectivities over oX and eB are among the highest yet reported. Moreover, M also exhibits strong vapor extraction selectivity and can be regenerated by exposure to vacuum drying.