Enhanced adsorption performance of a novel Fe‐Mn‐Zr metal oxide nanocomposite adsorbent for anionic dyes from binary dye mix: Response surface optimization and neural network modeling

Effective removal of acetamiprid and eosin Y by adsorption on pristine and modified MIL-101(Fe)

In this work, the efficacy of two metal-organic frameworks (MIL-101(Fe) and NH2-MIL-101(Fe)) in eliminating acetamiprid (ATP) insecticide and eosin Y (EY) dye from aqueous solution is tested. An analysis was conducted on the developed nanocomposite's optical, morphological, and structural characteristics. The adsorption isotherm, kinetics, thermodynamics, reusability, and mechanisms for ATP and EY dye removal were assessed. NH2-MIL-101(Fe) adsorbed 76% and 90% of ATP pesticide and EY dye, respectively after 10 to 15 min in optimum conditions. For both adsorbents, with regard to explaining the isotherm data, the Langmuir model offered the most accurate description. Moreover, the adsorption of ATP and EY dye is described by the pseudo-second-order kinetic model. The maximum adsorption capacities of ATP and EY dye on MIL-101(Fe) were 57.6 and 48.9 mg/g compared to 70.5 and 97.8 mg/g using NH2-MIL-101(Fe). The greatest amount of ATP and EY dye clearance was obtained at a neutral medium for both adsorbents. The results of this investigation demonstrate the effectiveness of MIL-101(Fe) and NH2-MIL-101(Fe) as effective substances in the adsorption process for removing pesticides and dyes from aqueous solution.

Mesoporous carbon structure impregnated with 2D engineered zirconium: A sustainable adsorbent for the removal of dyes from the aqueous solution

The key designing of new breeds of the adsorbents aimed to improve the physical, chemical and textural morphology along with surface functionalization, selectivity toward the contaminants, and regenerations efficiency. In this aspect, two adsorbents named wet oxidative and ultrasonicated zirconium impregnated composite, have been synthesized through two routes, i.e., wet oxidation and ultrasonication. In wet oxidation method, carbon-based materials are oxidized using an oxidant followed by impregnation, while in ultrasonication assisted route, the impregnation is carried out using acoustic phenomenon. The characterization study revealed that the wet oxidation process is more competent in impregnating zirconium and developing diverse porosity and functionalities. The maximum adsorption capacity of wet oxidative adsorbent was 812 mg/g for Reactive Blue 19 and 203.18 mg/g for Methylene Blue, that accentuated the efficiency of the adsorbent over raw activated carbon. The electrostatic interaction, hydrogen-bonding and ligand exchange phenomenon are the involved adsorption mechanism for dyes. The regeneration study finally asserts that the wet oxidative adsorbent shows an insignificant decrease in its capacity up to the 5^th-cycle (i.e., 87.67% removal at 5^th cycle) as compared to raw AC (46.71% removal at 5th cycle). Further, a continuous fixed-bed column study revealed a significant correlation between experimental breakthrough data and kinetic data. Thus, the developed adsorbent has a sedulous adsorption capacity to remove the most stubborn toxic dyes and can be used in industrial-scale applications.

Recent advances in application of iron-manganese oxide nanomaterials for removal of heavy metals in the aquatic environment

Heavy metal pollution has a serious negative impact on the ecological environment and human health due to its toxicity, persistence, and non-biodegradable properties. Among the technologies applied in heavy metals removal, adsorption has been widely used as the most promising method because of its simple operation, high removal efficiency, strong applicability, and low cost. Iron-manganese oxide nanomaterials, as an effective absorbent, have attracted wide attention due to their simple preparation, wide material sources, and lower ecological impact. So far, no quantitative investigation has been conducted on the preparation and application of iron-manganese oxide nanomaterials in heavy metals removal. This review discussed the preparation methods and characteristics of iron‑manganese oxide nanomaterials over the past decade and provided some basic information for the improvement of preparation methods. The physicochemical properties of iron‑manganese oxide nanomaterials and environmental conditions are regarded as important factors that affect the removal efficiency of heavy metals. In addition, the removal mechanisms of heavy metals in aqueous solution with iron‑manganese oxide nanomaterials were mainly included redox, complex precipitation, electrostatic attraction, and ion exchange. The reusability and practicability in actual wastewater treatment of 3nganese oxide nanomaterials were further discussed. Several key problems still need to be solved in the existing progress, such as improving the ability and stability of the iron‑manganese oxide nanomaterials to remove heavy metals from actual wastewater. In conclusion, this review provides a future direction for the application of iron‑manganese oxide nanomaterials for heavy metals removal and even in the large-scale treatment of actual wastewater.

Preparation and Characterization of Chitosan/Bentonite Composites for Cr (VI) Removal from Aqueous Solutions

Chitosan/bentonite composites (CSBT) prepared by physical gelation were tested for the adsorption of Cr (VI) from aqueous solutions in this work. The composites were prepared at a mass ratio from 2 : 1 to 1 : 2, and a composite of 1 : 1 was found to be most suitable for efficient Cr (VI) removal. The influencing parameters, including temperature, adsorbent dose, and pH, were statistically optimized using response surface methodology (RSM) for the removal of Cr (VI). The pH was found to be the limiting factor during the adsorption process, and under the optimal conditions, namely, adsorbent dose of 400 mg/L, $\text{pH}=3$ , and temperature of 298 K, 87.61% Cr (VI) would be removed expectantly. The mechanism of Cr (VI) removal by CSBT was discussed, and the protonation of amino groups on chitosan followed by the combination of -NH3+ and anionic hexavalent chromium was the primary driving force. In addition, the removal of Cr (VI) onto CSBT was monolayer adsorption with a maximum adsorption capacity of 133.85 mg/g by the Langmuir isotherm. CSBT follows a pseudosecond-order kinetic model, and within 1.5 h, adsorption was observed to reach equilibrium. The calculated thermodynamic functions clarified that the adsorption process was exothermic and spontaneous below 312.60 K. CSBT could be regenerated after desorption by 0.5 mol/L NaOH solutions and exhibited superior reusability after six cycles. This study demonstrated composites of chitosan/bentonite as eco-friendly bioadsorbents for the removal of Cr (VI) from aqueous environments.

Super adsorption performance of carboxymethyl cellulose/copper oxide-nickel oxide nanocomposite toward the removal of organic and inorganic pollutants

A novel nanocomposite bead based on polymeric matrix of carboxymethyl cellulose and copper oxide-nickel oxide nanoparticles was synthesized, characterized, and applied for adsorptive removal of inorganic and organic contaminants at trace level of part per million (mgL^-1) from aqueous sample. Carboxymethyl cellulose/copper oxide-nickel oxide (CMC/CuO-NiO) adsorbent beads were selective toward the removal of Pb(II) among other metal ions. The removal percentage of Pb(II) was more than 99% with 3 mgL^-1. The waste beads after Pb (II) adsorption (Pb@CMC/CuO-NiO) and CMC/CuO-NiO nanocomposite beads were employed as adsorbents for removing of various dyes. It was found that Pb@CMC/CuO-NiO can be reused as adsorbent for the removal of Congo Red (CR), while CMC/CuO-NiO nanocomposite beads were more selective for removal of Eosin Yellow (EY) from aqueous media. The adsorption of CR and EY was optimized, and the removal percentages were 93% and 96.4%, respectively. The influence of different parameters was studied on the uptake capacity of Pb(II), CR, and EY, and lastly, the CMC/CuO-NiO beads exhibited responsive performance in relation to pH and other parameters. Thus, the prepared CMC/CuO-NiO beads were found to be a smart material which is effective and played super adsorption performance in the removal of Pb(II), CR, and EY from aqueous solution. These features make CMC/CuO-NiO beads suitable for numerous scientific and industrial applications and may be used as an alternative to high-cost commercial adsorbents.

Boosted sono-oxidative catalytic degradation of Brilliant green dye by magnetic MgFe2O4 catalyst: Degradation mechanism, assessment of bio-toxicity and cost analysis

The magnetic MgFe₂O₄ nanoparticles (NPs) were fabricated via a facile co-precipitation technique and was comprehensively characterized by XRD, FTIR, SEM, EDX and VSM. The prepared NPs were used as catalyst in presence of ultrasound (US) irradiation to activate persulfate (PS) for generation of sulfate radicals (SO₄^·-) for boosted degradation of toxic Brilliant Green (BG) dye. Preliminary experiments revealed that highest BG dye degradation efficiency of 91.63% was achieved at MgFe₂O₄ catalyst dose of 1.0 g/L, PS dose of 300 mg/L, and initial dye concentration of 70 ppm within 15 min of US irradiation. However, only US, US in presence of PS oxidation and US in presence of MgFe₂O₄ catalyst have shown 20.2%, 83.6% and 45.0% of BG dye removal, respectively. Furthermore, response surface methodology (RSM) based central composite design (CCD) was executed to investigate the effect of interaction between independent variables such as MgFe₂O₄ catalyst dose (0.5-1.5 g/L), PS dose (150-350 mg/L), initial BG dye concentration (50-150 ppm) and US irradiation time (4-12 min). The RSM based quadratic model was used to predict the experimental data, and the prediction accuracy was confirmed by analysis of variance (R² = 0.98). The established RSM model has predicted the optimum experimental conditions as MgFe₂O₄ catalyst dose of 0.75 g/L, PS dose of 300 mg/L, initial dye concentration of 75 ppm and sonication time of 10 min. Subsequently, the treatment cost analysis was performed for all thirty experimental runs of CCD, and the RSM predicted response was found to be evidently optimum as this has delivered best economic condition (140 $/kg of BG removed) with respect to relative dye removal (%). COD removal and residual sulfate analysis have demonstrated satisfactory reduction of COD (90.31%) as well as sulfate ions (42.87 ppm) in the dye solution after treatment. Results of degradation pathway analysis portrayed the transformation of BG molecule (M/Z ratio 385) into simpler fractions with M/Z ratio of 193, 161, 73, and 61. Moreover, the toxicity analysis revealed that sono-catalytically activated PS system has efficiently reduced the toxicity level of BG dye from 93.9% to 5.13%.

Synthesis and Characterization of Magnetic Superadsorbent Fe3O4-PEG-Mg-Al-LDH Nanocomposites for Ultrahigh Removal of Organic Dyes

Considering the huge demands for economical and reliable eco-remediation applications, the goal of the present work is to synthesize cost-effective and functionally efficient magnetic layered nanocomposite adsorbents for the effective adsorption of dyes followed by easy separation from wastewater. This would ensure good reusability of adsorbents without altering its adsorption capacity in a relatively short time manner. To achieve this, different molecular weights of polyethylene glycol (PEG)-modified Fe₃O₄ combined with Mg-Al-layered double hydroxides (MAN-LDH) were synthesized and characterized using powder X-ray diffraction, Fourier transform infrared, scanning electron microscopy, transmission electron microscopy, thermogravimetric analysis, differential thermal analysis, energy-dispersive X-ray, and inductively coupled plasma optical emission spectroscopy. The efficacy of various adsorption parameters for the removal of methyl orange (MO) from water using Fe₃O₄-PEG-Mg-Al-LDH (FPL) adsorbents with different molecular weights of PEG (2FPL, 4FPL, and 6FPL) were investigated, and the results were compared. The maximum adsorption capacities of 2FPL, 4FPL, and 6FPL for MO were found to be 775.19, 826.44, and 833.33 mg/g, respectively. Detailed adsorption studies confirm that the higher adsorption capacity of 6FPL is due to the fast exchange of anions (NO₃ ^-) by MO in the interlayers of MAN-LDH, larger surface area, hydrogen bonding, and electrostatic interaction between adsorbate and adsorbent. The thermodynamic data indicate that the adsorption behavior is spontaneous and endothermic in nature. The reusability of all FPL adsorbents is observed to be excellent. The MAN-LDH recoated after the 31st-cycle nanocomposites show a recovery of 100% adsorption efficiency, similar to the freshly prepared 6FPL. Such systematic studies greatly help in advancing the applications of newly functionalized nanomaterials toward eco-remediation approaches.

Effect of single and binary mixed surfactant impregnation on the adsorption capabilities of chitosan hydrogel beads toward rhodamine B

The adsorption of cationic xanthene dye rhodamine B (RhB) on pure chitosan (CS), single surfactant (SDS, Brij30 and DTAB) and binary surfactant (SDS-Brij30 and DTAB-Brij30) modified chitosan beads has been investigated.

The preparation of a novel iron/manganese binary oxide for the efficient removal of hexavalent chromium [Cr(vi)] from aqueous solutions

To remove hexavalent chromium Cr(vi) efficiently, a novel Fe–Mn binary oxide adsorbent was prepared via a “two-step method” combined with a co-precipitation method and hydrothermal method. The as-prepared Fe–Mn binary oxide absorbent was characterized via transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier-transform infrared spectra (FTIR), thermogravimetric analysis (TGA), zeta potential, BET and X-ray photoelectron spectroscopy (XPS). The results indicated that the morphology of the adsorbent was rod-like with length of about 100 nm and width of about 50–60 nm, specific surface area was 63.297 m² g⁻¹, has the composition of α-Fe₂O₃, β-MnO₂ and MnFe₂O₄ and isoelectric point was observed at pH value of 4.81. The removal of Cr(vi) was chosen as a model reaction to evaluate the adsorption capacity of the Fe–Mn binary oxide adsorbent, indicating that the Fe–Mn binary oxide adsorbent showed high adsorption performance (removal rate = 99%) and excellent adsorption stability (removal rate > 90% after six rounds of adsorption). The adsorption behavior of the Fe–Mn binary oxide was better represented by the Freundlich model (adsorption isotherm) and the pseudo-second-order model (adsorption kinetic), suggesting that the adsorption process was multi-molecular layer chemical adsorption. The possible adsorption mechanism of the Fe–Mn binary oxide for the removal of Cr(vi) included the protonation process and the electrostatic attraction interactions.

A novel Fe–Mn binary oxide adsorbent prepared via “co-precipitation and hydrothermal” method, for the efficient and fast removal of Cr(vi).

Mature landfill leachate treatment using sonolytic-persulfate/hydrogen peroxide oxidation: Optimization of process parameters

The suitability of stand-alone ultrasound (US) system, coagulation pre-treatment followed by US, hydrogen peroxide added US system (US-H₂O₂) and persulfate added US system (US-PS) for the treatment of matured landfill leachate was investigated. With US system, around 67% COD removal and an increase in BOD/COD ratio were observed (from 0.033 to 0.142) after 15 min at 30% US amplitude. However, the energy input required for landfill leachate treatment in US system was found to be very high due to the presence of fixed solids. Coagulation pretreatment using alum was carried out to improve the overall COD removal and reduce the cost of treatment. As a result, the COD removal was increased to 78% (42% in pretreatment and 36% in US) in 15 min. On the other hand, US-H₂O₂ and US-PS hybrid systems have shown significant improvement in COD removals (93% and 86%, respectively) from raw leachate after 15 min. Subsequently, a three factor (i.e. PS dose (mg/L), H₂O₂ dose (mol/L), and US amplitude (%)) 5-level design of experiment was used to maximize the COD removal efficiency by response surface methodology (RSM). The RSM model generated a quadratic equation to accurately analyze the influence of input variables on COD removal efficiency (R² of 0.92). A maximum COD removal of 98.3% was predicted using the model and the corresponding optimal experimental condition were identified as follows: PS dose ∼4700 mg/L, H₂O₂ dose ∼0.7 mol/L and US amplitude ∼49%. The overall observations reveals that PS and H₂O₂ coupled with US system has a great prospective to treat mature landfill leachate.

Ultrasonic assisted enhanced adsorption of methyl orange dye onto polyaniline impregnated zinc oxide nanoparticles: Kinetic, isotherm and optimization of process parameters

The fabrication of novel functionalized composite materials as adsorbent is considered to be the core research area in adsorption technology for environmental applications. Indiscriminate disposal of industrial effluents containing toxic dyes has become a serious environmental issue across the globe since last few decades. In view of above, this study focused on the performance evaluation of ZnO/polyaniline nanocomposite (ZnO-PANI-NC) for quick ultrasonic assisted adsorptive remediation of methyl orange dye from aqua matrix. ZnO nanoparticles were fabricated by a simple co-precipitation method and ZnO-PANI-NC was synthesized by in situ oxidative polymerization of aniline monomer in presence of ZnO nanoparticles. The nanocomposite was extensively characterized for its crystalline nature, morphological characteristics, surface chemical bonding, specific surface area and pore volume by employing XRD, SEM, TEM, FTIR, and BET analysis. The ZnO-PANI-NC has shown superior adsorptive performance as compared to pure PANI as well as ZnO nanoparticles and the maximum monolayer adsorption capacity of 240.84 mg/g was obtained for the ZnO-PANI-NC. Under ultrasonic environment the adsorption reaction reached to equilibrium (more than 98% MO dye removal) within 15 min of reaction. Adsorption process followed Langmuir isotherm model and second order kinetic model strictly and contribution of intra-particle diffusion was also observed. The ZnO-PANI-NC has shown its high regeneration ability (more than 86%) even after 5th consecutive cycles of adsorption-desorption. Response surface methodology based optimization was used to optimize the adsorption experimental data and maximum MO removal of 99.12% was observed at optimum sonication time 13 min, adsorbent dose 0.38 g/L and initial MO concentration at 28 mg/L.