UV Irradiation-induced crosslinking of aqueous solution of poly(ethylene oxide) with benzophenone as initiator

Metal-Organic Framework-Supported Poly(ethylene oxide) Composite Gel Polymer Electrolytes for High-Performance Lithium/Sodium Metal Batteries

Thanks to their high energy density, lithium/sodium metal batteries (LMBs/SMBs) are considered to be the most promising next-generation energy storage system. However, the instability of the electrode/electrolyte interface and dendrite growth seriously hinders commercial application of LMBs/SMBs. In addition, traditional liquid electrolytes are inflammable and explosive. As a key part of the battery, the electrolyte plays an important role in solving the abovementioned problems. Although solid electrolytes can alleviate dendrite growth and liquid electrolyte leakage, their low ionic conductivity and poor interfacial contact are not conducive to improvement of overall LMBs/SMB performances. Therefore, it is necessary to find a balance between liquid and solid electrolytes. Gel polymer electrolytes (GPEs) are one means for achieving high-performance LMBs/SMBs because they combine the advantages of liquid and solid electrolytes. Metal-organic frameworks (MOFs) benefit from high specific surface areas, ordered internal porous structures, organic-inorganic hybrid properties, and show great potential in modified electrolytes. Here, Cu-based MOF-supported poly(ethylene oxide) composite gel polymer electrolytes (CGPEs) were prepared by ultraviolet curing. This CGPE exhibited high ionic conductivity, a wide electrochemical window, and a high ion transference number. In addition, it also exhibited excellent cycle stability in symmetric batteries and LMBs/SMBs. This study showed that CGPE had great practical application potential in the next-generation LMBs/SMBs.

UVA-Triggered Drug Release and Photo-Protection of Skin

Light has attracted special attention as a stimulus for triggered drug delivery systems (DDS) due to its intrinsic features of being spatially and temporally tunable. Ultraviolet A (UVA) radiation has recently been used as a source of external light stimuli to control the release of drugs using a "switch on- switch off" procedure. This review discusses the promising potential of UVA radiation as the light source of choice for photo-controlled drug release from a range of photo-responsive and photolabile nanostructures via photo-isomerization, photo-cleavage, photo-crosslinking, and photo-induced rearrangement. In addition to its clinical use, we will also provide here an overview of the recent UVA-responsive drug release approaches that are developed for phototherapy and skin photoprotection.

UV cross-linked polyvinylpyrrolidone electrospun fibres as antibacterial surfaces

Many bacteria become progressively more resistant to antibiotics and it remains a challenging task to control their overall levels. Polymers combined with active biomolecules come to the forefront for the design of antibacterial materials that can address this encounter. In this work, we investigated the photo-crosslinking approach of UV-sensitive benzophenone molecule (BP) with polyvinylpyrrolidone (PVP) polymer within electrospun fibres. The BP and PVP solutions allowed fabricating polymer mats that were subsequently functionalised with antibacterial lysozyme. The physical properties of the crosslinked electrospun fibres were investigated by scanning electron microscopy and atomic force microscopy. The average diameter of the obtained fibres decreased from 290 ± 50 nm to 270 ± 70 nm upon the addition of the crosslinking molecules and then to 240 ± 80 nm and 180 ± 90 nm after subsequent crosslinking reaction at an increasing time: 3 and 5 h, respectively. The peak force quantitative nanomechanical mapping (PF-QNM) indicated the increase of DMT modulus of obtained cross-linked fibres from 4.1 ± 0.8 GPa to 7.2 ± 0.5 GPa. Furthermore, the successful crosslinking reaction of PVP and BP solution into hydrogels was investigated in terms of examining photo-crosslinking mechanism and was confirmed by rheology, Raman, Fourier transform infrared and nuclear magnetic resonance. Finally, lysozyme was successfully encapsulated within cross-linked PVP-BP hydrogels and these were successfully electrospun into mats which were found to be as effective antibacterial agents as pure lysozyme molecules. The dissolution rate of photo cross-linked PVP mats was observed to increase in comparison to pure PVP electrospun mats which opened a potential route for their use as antibacterial, on-demand, dissolvable coatings for various biomedical applications.

Cyclic Extrusion of Recycled High Density Polyethylene/Banana Fiber/Fly Ash Cenosphere Biocomposites: Thermal and Mechanical Retention Properties

Disposal of composite materials used vastly in structural applications raises the need to study the reprocessability of these systems for environmental benefits. In this paper, composites of recycled high density polyethylene (R) containing 30 wt.% banana fiber (BF)/7.5 wt.% fly ash cenospheres (FACS) were prepared with 3 wt.% maleic anhydride grafted high density polyethylene (MA-g-HDPE) as a coupling agent using twin screw extrusion followed by injection molding. The effects of thermal cycles (two times extrusion followed by injection molding) were studied on R and its composites. The samples were characterized by using tensile, flexural, izod impact tests, scanning electron microscopy (SEM), differential scanning calorimetry (DSC), thermogravimetry (TGA) and dynamic mechanical analysis (DMA). The tensile and flexural properties were improved by addition of both BF/FACS into the R matrix. The percentage retention in tensile properties of R/BF/FACS(E2) biocomposites (i.e. two times extrusion followed by injection molding) is more than 80 %, while that for flexural properties is more than 90 %. This indicates that R/BF/FACS composites exhibit good retention ability in mechanical properties after subjecting to two times twin-screw extrusion followed by injection molding. DSC results revealed that repeated extrusion improved the crystallization temperature and crystallinity of the composites with a slight reduction in melting temperature. From the TGA results, it was observed that the thermal stability (e.g. Tonset) of R was reduced by the addition of BF/FACS. However, repeated extrusion showed an improvement in thermal stability of the composites.

On the Limits of Benzophenone as Cross-Linker for Surface-Attached Polymer Hydrogels

The synthesis of different photo-reactive poly(alkenyl norbornenes) and poly(oxonorbornenes) containing benzophenone (BP) via ring-opening metatheses polymerization (ROMP) is described. These polymers are UV irradiated to form well-defined surface-attached polymer networks and hydrogels. The relative propensity of the polymers to cross-link is evaluated by studying their gel content and its dependency on BP content, irradiation wavelength (254 or 365 nm) and energy dose applied (up to 11 J·cm-²). Analysis of the UV spectra of the polymer networks demonstrates that the poly(oxonorbornenes) show the expected BP-induced crosslinking behavior at 365 nm, although high irradiation energy doses and BP content are needed. However, these polymers undergo chain scission at 254 nm. The poly(alkenyl norbornenes), on the other hand, do not cross-link at 365 nm, whereas moderate to good cross-linking is observed at 254 nm. UV spectra demonstrate that the cross-linking at 254 nm is due to BP cross-linking combined with a [2 + 2] cylcoaddition of the alkenyl double bonds. This indicates limitations of benzophenone as a universally applicable cross-linking for polymer networks and hydrogels.

Method to analyse energy and intensity dependent photo-curing of acrylic esters in bulk

The photo-polymerizations induced by three different model resins, containing well-known commercial initiators, are monitored by an in situ Raman UV-vis system and analysed in detail.