Mimicking natural deterrent strategies in plants using adhesive spheres

With a continuous increase in world population and food production, chemical pesticide use is growing accordingly, yet unsustainably. As chemical pesticides are harmful to the environment and developmental resistance in pests is increasing, a sustainable and effective pesticide alternative is needed. Inspired by nature, we mimic one defense strategy of plants, glandular trichomes, to shift away from using chemical pesticides by moving toward a physical immobilization strategy via adhesive particles. Through controlled oxidation of a biobased starting material, triglyceride oils, an adhesive material is created while monitoring the reactive intermediates. After being milled into particles, nanoindentation shows these particles to be adhesive even at low contact forces. A suspension of particles is then sprayed and found to be effective at immobilizing a target pest, thrips, Frankliniella occidentalis. Small arthropod pests, like thrips, can cause crop damage through virus transfer, which is prevented by their immobilization. We show that through a scalable fabrication process, biosourced materials can be used to create an effective, sustainable physical pesticide.

Preparation and structural characterization of epoxidized soybean oils-based pressure sensitive adhesive grafted with tea polyphenol palmitate

Vegetable oils-based pressure sensitive adhesives (PSAs) are green and sustainable but face unsatisfactory adhesion strengths and are prone to aging during storage and application due to the existence of residual double bonds and massive ester bonds. Nine common antioxidants (tea polyphenol palmitate (TPP), caffeic acid, ferulic acid, gallic acid, butylated hydroxytoluene, tertiary butylhydroquinone, butylated hydroxyanisole, propyl gallate, and tea polyphenols) were grafted into epoxidized soybean oils-PSA (ESO-PSA) system to enhance antiaging properties and adhesion strengths. Results showed ESO-PSAs grafted with caffeic acid, tertiary butylhydroquinone, butylated hydroxyanisole, propyl gallate, tea polyphenols, or TPP didn't occur failure with TPP having best performance. The optimal conditions were ESO reacted with 0.9 % TPP, 70 % rosin ester, and 7.0 % phosphoric acid at 50 °C for 5 min, under which peel strength and loop tack increased to 2.460 N/cm and 1.66 N, respectively, but peel strength residue reduced to 138.09 %, compared with control (0.407 N/cm, 0.43 N, and 1669.99 %). Differential scanning calorimetry and thermogravimetric results showed TPP grafting increased the glass transition temperature of ESO-PSA slightly but improved its thermal stability significantly. Fourier transform infrared spectroscopy and 1H nuclear magnetic resonance results showed TPP, phosphoric acid, and rosin ester all partially participated in the covalently crosslinking polymerization of ESO-PSAs and the rest existed in the network structures in the free form.

Pilot-scale production of mcl-PHA by Pseudomonas citronellolis using acetic acid as the sole carbon source

Medium-chain-length polyhydroxyalkanoates (mcl-PHA) are biobased materials with promising properties for environmentally friendly applications. Due to high production costs, which are related to the cost of the carbon sources combined with conversion insufficiencies, currently only small quantities are produced. This results in a lack of reliable data on properties and application potential for the variety of polymers from different types of production strains. This study investigated the potential for the production of mcl-PHA from volatile fatty acids (VFA) at a larger scale, given their potential as low-cost and sustainable raw material within a carboxylate-platform based biorefinery. Pseudomonas citronellolis (DSMZ 50332) was chosen as the production strain, and acetic acid was selected as the main carbon and energy source. Nitrogen was limited to trigger polymer production, and a fed-batch process using a pH-stat feeding regime with concentrated acid was established. We report successful production, extraction, and characterization of mcl PHA, obtaining a total of 1.76 kg from two 500-litre scale fermentations. The produced polymer was identified as a copolymer of 3-hydroxydecanoate (60.7%), 3-hydroxyoctanoate (37.3%), and 3-hydroxyhexanoate (2.0%) with a weight average molecular weight (Mw) of 536 kDa. NMR analysis indicates the presence of unsaturated side chains, which may offer additional possibilities for modification. The results confirm that there is a potential to produce significant amounts of mcl-PHA with interesting rubber-like properties from waste-derived VFA.

Thermal decomposition reaction kinetics and storage life prediction of polyacrylate pressure-sensitive adhesive

The thermal decomposition behavior of polyacrylate pressure-sensitive adhesive (PSA) at heating rates of 4, 6, 8, and 10 K·min−1 was measured by thermogravimetric analysis (TGA). The kinetic parameters for thermal decomposition reaction of the polyacrylate adhesive were obtained from TG profile by differential method and integral method (Kissinger, general integral, MacCallum–Tanner, Šatava–Šesták, Agrawal, and Flynn–Wall–Ozawa), the results show that the main decomposition stage of the polyacrylate adhesive starts at 301°C and its activation energy is 142.68 kJ·mol−1, the pre exponential factor is 109.55, the decomposition mechanism obeys Avrami–Erofeev equation and its decomposition kinetic equation can be expressed as: dα/dT = (109.55/β)[(1 − α)/2][−ln(1 − α)]−1exp(−1.7161 × 104/T). The storage life of PSA at 25°C was predicted to be about 19 years by isoconversional method.

Study of Applying Naturally Occurring Mineral Materials for Silicone Pressure-Sensitive Adhesives

Silicones are commonly used as adhesives when high-quality materials are required due to harsh environmental conditions such as high temperature, humidity, etc. To ensure high resistance to environmental conditions, including high temperatures, modifications of silicone adhesives are made using fillers. The characteristics of a modified silicone-based pressure-sensitive adhesive with filler are the focus of this work. Functionalized palygorskite was prepared in this investigation by grafting 3-mercaptopropyltrimethoxysilane (MPTMS) onto palygorskite (palygorskite-MPTMS). The palygorskite was functionalized using MPTMS under dried conditions. FTIR/ATR spectroscopy, thermogravimetric analysis, and elemental analysis were all used to characterize the obtained palygorskite-MPTMS. MPTMS loading onto palygorskite was also proposed. The results demonstrated that palygorskite's initial calcination favors the grafting of functional groups on its surface. New self-adhesive tapes based on palygorskite-modified silicone resins have been obtained. This functionalized filler allows for the improvement of the compatibility of palygorskite with specific resins for application in heat-resistant silicone pressure-sensitive adhesives. The new self-adhesive materials showed increased thermal resistance while maintaining good self-adhesive properties.

Approaches in Sustainable, Biobased Multilayer Packaging Solutions

The depletion of fossil resources and the growing demand for plastic waste reduction has put industries and academic researchers under pressure to develop increasingly sustainable packaging solutions that are both functional and circularly designed. In this review, we provide an overview of the fundamentals and recent advances in biobased packaging materials, including new materials and techniques for their modification as well as their end-of-life scenarios. We also discuss the composition and modification of biobased films and multilayer structures, with particular attention to readily available drop-in solutions, as well as coating techniques. Moreover, we discuss end-of-life factors, including sorting systems, detection methods, composting options, and recycling and upcycling possibilities. Finally, regulatory aspects are pointed out for each application scenario and end-of-life option. Moreover, we discuss the human factor in terms of consumer perception and acceptance of upcycling.

Ring-Opening Metathesis Polymerization for the Synthesis of Terpenoid-Based Pressure-Sensitive Adhesives

Pressure-sensitive adhesives (PSAs) made from norbornene-functionalized terpenoid-based monomers are reported as a possible alternative to the conventional petrochemically based PSAs. For this, tetrahydrogeranyl, menthyl, and isobornyl norbornenate monomers, with a renewable carbon content up to 72%, are synthesized and copolymerized via ring-opening metathesis polymerization (ROMP) with cyclooctadiene and 5-norbornene-2-carboxylic acid. ROMP enables a much faster and controlled polymerization process in comparison to free radical polymerization techniques when targeting high molecular weights and therefore unlocks a potential to design a unique class of PSA materials. The moduli at bonding and debonding frequencies of the obtained PSAs are plotted in the Chang classification system and are used to predict their adhesive performance. Tack and peel measurements indicate that the terpenoid-based norbornenate formulations show similar adhesive properties in comparison to the previously investigated acrylic counterparts.

Biodegradable copolyesters based on a “soft” isohexide building block with tunable viscoelasticity and self-adhesiveness

PBIA copolyesters synthesised using a novel glycosylated monomer (IIDMC) have faster degradation and tunable self-adhesiveness.

Synthesis, characteristics, and applications of modified starch nanoparticles: A review

Nowadays, starch nanoparticles (SNPs) are drawing attention to the scientific community due to their versatility and wide range of applications. Although several works have extensively addressed the SNP production routes, not much is discussed about the SNPs modification techniques, as well as the use of modified SNPs in typical and unconventional applications. Here, we focused on the SNP modification strategies and characteristics and performance of the resulting products, as well as their practical applications, while pointing out the main limitations and recommendations. We aim to guide researchers by identifying the next steps in this emerging line of research. SNPs esterification and oxidation are preferred chemical modifications, which result in changes in the functional groups. Moreover, additional polymers are incorporated into the SNP surface through copolymer grafting. Physical modification of starch has demonstrated similar changes in the functional groups without the need for toxic chemicals. Modified SNPs rendered differentiated properties, such as size, shape, crystallinity, hydrophobicity, and Zeta-potential. For multiple applications, tailoring the aforementioned properties is key to the performance of nanoparticle-based systems. However, the number of studies focusing on emerging applications is fairly limited, while their applications as drug delivery systems lack in vivo studies. The main challenges and prospects were discussed.

On-Demand Manufacturing Capabilities of Mussels Enable Robust Adhesion to Geometrically Complex Surfaces

Marine mussels have the remarkable ability to adhere to a variety of natural and artificial surfaces under hostile environmental conditions. Although the molecular composition of mussel adhesives has been well studied, a mechanistic understanding of the physical origins of mussels' impressive adhesive strength remains elusive. Here, we investigated the role of substrate geometry in the adhesive performance of mussels. Experimentally, we created substrates with differing surface properties using 3D printing and laser drilling and introduced these to mussels, which in turn adhered to the engineered surfaces via plaque-thread byssal structures. Tensile testing with in situ imaging was conducted to quantify the adhesion strength of the mussel plaques, and the microstructures of the mechanically deformed plaques were characterized using scanning electron microscopy. Our results reveal that the geometry of the surfaces has no significant impact on the detachment force and the strain, whereas the change in adhesion area leads to a different adhesion stress. Ultrastructural analysis confirms the expected presence of an open-cell foamy network coated with the cuticle. The observed detachment dynamics and failure mechanisms do vary depending on the substrate properties, suggesting the presence of substrate-dependent nonuniform stress distributions at the interface. Together, these results show mussels' remarkable ability to adapt to differing physical conditions and demonstrate the importance of the on-demand and in situ manufacturing of the stiff cuticle and relatively compliant adhesive interlayer. The resultant composite structure avoids the formation of prestress during the formation of the adhesive joint, provides conformability to the surface, and helps compensate for local bending interactions to maintain adhesive strength. Our findings suggest forward design strategies to improve adhesive performance on complex surfaces.

Sustainable UV-Crosslinkable Acrylic Pressure-Sensitive Adhesives for Medical Application

This study aimed to investigate the potential of photoreactive acrylate patches as systems for transdermal drug delivery, in particular, using more renewable alternatives and more environmentally friendly synthesis routes of transdermal patches. Therefore, the aim of this study was to develop a transdermal patch containing ibuprofen and investigate its performance in vitro through the pigskin. Transparent patches were prepared using four acrylate copolymers with an incorporated photoinitiator. Two types of transdermal patches based on the photocrosslinking acrylic prepolymers with isobornyl methacrylate as biocomponent and monomer increasing Tg ("hard") were manufactured. The obtained patches were characterized for their adhesive properties and tested for permeability of the active substance. It turns out that patches whose adhesive matrix is photoreactive polyacrylate copolymers have a higher cohesion than patches from commercial adhesives, while the modification of the copolymers with isobornyl methacrylate resulted in an improvement in adhesion and tack. This study demonstrates the feasibility of developing photoreactive acrylic-based transdermal patches that contain biocomponents that can deliver a therapeutically relevant dose of ibuprofen.

RAFT polymerisation of renewable terpene (meth)acrylates and the convergent synthesis of methacrylate–acrylate–methacrylate triblock copolymers

We now report the synthesis of well-defined terpene-based polymers and precise di- and multiblock copolymer architectures by use of RAFT, wide range of T_g and promising adhesive properties are observed.

Bio-based and Degradable Block Polyester Pressure-Sensitive Adhesives

A new class of bio-based fully degradable block polyesters are pressure-sensitive adhesives. Bio-derived monomers are efficiently polymerized to make block polyesters with controlled compositions. They show moderate to high peel adhesions (4-13 N cm-1 ) and controllable storage and loss moduli, and they are removed by adhesive failure. Their properties compare favorably with commercial adhesives or bio-based polyester formulations but without the need for tackifier or additives.

Biosourced All-Acrylic ABA Block Copolymers with Lactic Acid-Based Soft Phase

Lactic acid is one of the key biobased chemical building blocks, given its readily availability from sugars through fermentation and facile conversion into a range of important chemical intermediates and polymers. Herein, well-defined rubbery polymers derived from butyl lactate solvent were successfully prepared by reversible addition–fragmentation chain transfer (RAFT) polymerization of the corresponding monomeric acrylic derivative. Good control over molecular weight and molecular weight distribution was achieved in bulk using either monofunctional or bifunctional trithiocarbonate-type chain transfer agents. Subsequently, poly(butyl lactate acrylate), with a relative low T_g (−20 °C), good thermal stability (5% wt. loss at 340 °C) and low toxicity was evaluated as a sustainable middle block in all-acrylic ABA copolymers using isosorbide and vanillin-derived glassy polyacrylates as representative end blocks. Thermal, morphological and mechanical properties of copolymers containing hard segment contents of <20 wt% were evaluated to demonstrate the suitability of rubbery poly(alkyl lactate) building blocks for developing functional sustainable materials. Noteworthy, 180° peel adhesion measurements showed that the synthesized biosourced all-acrylic ABA copolymers possess competitive performance when compared with commercial pressure-sensitive tapes.

Aldehyde-Assisted Lignocellulose Fractionation Provides Unique Lignin Oligomers for the Design of Tunable Polyurethane Bioresins

Thanks to chemical stabilization, aldehyde-assisted fractionation (AAF) of lignocellulosic biomass has recently emerged as a powerful tool for the production of largely uncondensed lignin. Depolymerization of AAF lignin via ether cleavage provides aromatic monomers at near theoretical yields based on ether cleavage and an oligomeric fraction that remains largely unexploited despite its unique material properties. Here, we present an in-depth analytical characterization of AAF oligomers derived from hardwood and softwood in order to elucidate their molecular structures. These bioaromatic oligomers surpass technical Kraft lignin in terms of purity, solubility, and functionality and thus cannot even be compared to this common feedstock directly for material production. Instead, we performed comparative experiments with Kraft oligomers of similar molecular weight (Mn ∼ 1000) obtained through solvent extraction. These oligomers were then formulated into polyurethane materials. Substantial differences in material properties were observed depending on the amount of lignin, the botanical origin, and the biorefining process (AAF vs Kraft), suggesting new design principles for lignin-derived biopolymers with tailored properties. These results highlight the surprising versatility of AAF oligomers towards the design of new biomaterials and further demonstrate that AAF can enable the conversion of all biomass fractions into value-added products.

Progress Toward Sustainable Reversible Deactivation Radical Polymerization

The recent focus of media and governments on renewability, green chemistry, and circular economy has led to a surge in the synthesis of renewable monomers and polymers. In this review, focussing on renewable monomers for reversible deactivation radical polymerizations (RDRP), it is highlighted that for the majority of the monomers and polymers reported, the claim to renewability is not always accurate. By closely examining the sustainability of synthetic routes and the renewability of starting materials, fully renewable monomers are identified and discussed in terms of sustainability, polymerization behavior, and properties obtained after polymerization. The holistic discussion considering the overall preparation process of polymers, that is, monomer syntheses, origin of starting materials, solvents used, the type of RDRP technique utilized, and the purification method, allows to highlight certain topics which need to be addressed in order to progress toward not only (partially) renewable, but sustainable monomers and polymers using RDRPs.

Pressure-Sensitive Tissue Adhesion and Biodegradation of Viscoelastic Polymer Blends

Viscoelastic blends of biodegradable polyesters with low and high molecular weight distributions have remarkably strong adhesion (significantly greater than 1 N/cm2) to soft, wet tissue. Those that transition from viscous flow to elastic, solidlike behavior at approximately 1 Hz demonstrate pressure-sensitivity yet also have sufficient elasticity for durable bonding to soft, wet tissue. The pressure-sensitive tissue adhesive (PSTA) blends produce increasingly stronger pull-apart adhesion in response to compressive pressure application, from 10 to 300 s. By incorporating a stiffer high molecular weight component, the PSTA exhibits dramatically improved burst pressure (greater than 100 kPa) when used as a tissue sealant. The PSTA's biodegradation mechanism can be switched from erosion (occurring primarily over the first 10 days) to bulk chemical degradation (and minimal erosion) depending on the chemistry of the high molecular weight component. Interestingly, fibrosis toward the PSTA is reduced when fast-occurring erosion is the dominant biodegradation mechanism.

Non-thermal microwave effects in radical polymerization of bio-based terpenoid (meth)acrylates

Non-thermal microwave effects are operative for terpenoid acrylates but not for methacrylates, provided that a minimum irradiation power is applied.

Solvent-Free Deposition of Ultrathin Copolymer Films with Tunable Viscoelasticity for Application to Pressure-Sensitive Adhesives

A new fabrication method for an ultrathin (500 nm thick) pressure-sensitive adhesive (PSA) was demonstrated by utilizing a series of in situ cross-linked viscoelastic copolymer films. Viscoelastic films composed of poly(2-hydroxyethyl acrylate- co-2-ethylhexyl acrylate) were synthesized successfully in a one-step manner by an initiated chemical vapor deposition (iCVD) process, where free-radical polymerization is triggered in the vapor phase either by heat or UV, or a combination of both. In particular, the photoinitiated chemical vapor deposition method generated a highly cross-linked polymer film, whereas cross-linking of the copolymer film was suppressed greatly in the conventional thermal iCVD method. A combination of thermal and photoinitiated chemical vapor deposition could regulate the cross-linking density of the copolymer films. We controlled the cross-linking density of the copolymer films to exhibit a viscoelastic property so that they would readily adhere to various kinds of substrates with only 500 nm thick copolymer PSA. The adhesion performance of the PSA was systematically optimized by tuning the copolymer composition as well as the cross-linking density, and consequently a high shear strength of more than 85.2 ± 5 N/cm² was achieved despite the 500 nm thickness. In addition, the PSA was completely transparent. We expect that the ultrathin PSAs developed in this work will be utilized widely for the realization of various soft electronic devices, which usually require strong adhesion, tunable viscoelastic properties, and optical transparency.

From Tree to Tape: Direct Synthesis of Pressure Sensitive Adhesives from Depolymerized Raw Lignocellulosic Biomass

We report a new and robust strategy toward the development of high-performance pressure sensitive adhesives (PSAs) from chemicals directly obtained from raw biomass deconstruction. A particularly unique and translatable aspect of this work was the use of a monomer obtained from real biomass, as opposed to a model compound or lignin-mimic, to generate well-defined and nanostructure-forming polymers. Herein, poplar wood depolymerization followed by minimal purification steps (filtration and extraction) produced two aromatic compounds, 4-propylsyringol and 4-propylguaiacol, with high purity and yield. Efficient functionalization of those aromatic compounds with either acrylate or methacrylate groups generated monomers that could be easily polymerized by a scalable reversible addition-fragmentation chain-transfer (RAFT) process to yield polymeric materials with high glass transition temperatures and robust thermal stabilities, especially relative to other potentially biobased alternatives. These lignin-derived compounds were used as a major component in low-dispersity triblock polymers composed of 4-propylsyringyl acrylate and n-butyl acrylate (also can be biobased). The resulting PSAs exhibited excellent adhesion to stainless steel without the addition of any tackifier or plasticizer. The 180° peel forces were up to 4 N cm^-1, and tack forces were up to 2.5 N cm^-1, competitive with commercial Fisherbrand labeling tape and Scotch Magic tape, demonstrating the practical significance of our biomass-derived materials.

Thermo-responsive gels based on supramolecular assembly of an amidoamine and citric acid

In this work, we report the formation of a novel, aqueous-based thermo-responsive, supramolecular gelling system prepared by a convenient and efficient self-assembly of a long-chain amino-amide and citric acid. To determine the viscosity behavior and to gain insights into the gelation mechanism, a complementary combination of techniques, including Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), dynamic light scattering (DLS), and sinusoidal oscillatory tests, were used. The supramolecular gelator exhibited remarkably reversible sol-gel transitions induced by temperature at 76 °C. At a concentration of 5 wt%, the zero-frequency viscosity of the supramolecular system increased by about four orders of magnitude (from 4.2 to 12 563 Pa s) by changing the temperature from 23 °C to 76 °C. The viscous nature of the supramolecular gel could be preserved up to 90 °C. The synergistic combination of the hydrogen bonding between amino and carboxylic acid groups and the electrostatic interactions arising from the protonation of the amino-group and the deprotonation of carboxylic acid groups enhanced at higher temperatures is presumably responsible for the thermo-responsive behavior. We anticipate that these supramolecular gelators can be beneficial in various applications such as hydrogel scaffolds for regenerative medicine, personal care products and cosmetics, and enhanced oil recovery as viscosity modifiers.

Thiol–ene adhesives from clove oil derivatives

This paper reports the synthesis of catechol-functionalized thiol–ene networks as photocurable adhesives, where adhesive interactions are derived from 4-allylpyrocatechol – an alkene readily obtained from Syzygium aromaticum flower buds (clove oil).