Antibacterial, antioxidant and fruit packaging ability of biochar-based silver nanoparticles-polyvinyl alcohol-chitosan composite film

Silver nanoparticles were prepared by loading Ag+ into biochar of waste barley distillers' grains shell by reduction with trisodium citrate, and this silver-loaded biochar was introduced into polyvinyl alcohol-chitosan. Various analysis with Fourier Transform Infrared spectroscopy, X-ray diffraction, Thermogravimetric analysis, and water contact angle revealed that biochar-based silver nanoparticle was incorporated into the polyvinyl alcohol-chitosan film, the biochar-based silver nanoparticles-polyvinyl alcohol-chitosan (C-Ag-loaded PVA/CS) composite film had good thermostability and hydrophobicity. Through the analysis via disk diffusion method, the composite containing 3 % of biochar-based silver nanoparticles-polyvinyl alcohol-chitosan had high antibacterial activity (inhibition zone: 18 mm against E. coli and 15 mm against S. aureus), and the bacterial membrane permeability was measured, indicating that C-Ag-loaded PVA/CS composite film could destroy the cell membrane, release intracellular substances, and have high antioxidant activity. During the storage, the weight loss rate of the biochar-based silver nanoparticles-polyvinyl alcohol-chitosan plastic wrap group was 0.14 %, and the titratable acid content only decreased by 0.061 %, which had a good effect on extending the shelf life of blueberries. The C-Ag-loaded PVA/CS composite film could also delay deterioration of blueberries and prolong storage time. Overall, this composite film had potential in food packaging and extending food shelf-life aspects.

Incorporation of mixed-dimensional palygorskite clay into chitosan/polyvinylpyrrolidone nanocomposite films for enhancing hemostatic activity

Clay mineral-based hemostatic materials have attracted much attention in recent years, but it is scarce to report the hemostatic nanocomposite films containing natural mixed-dimensional clay composed of natural one-dimensional and two-dimensional clay minerals. In this study, the high-performance hemostatic nanocomposite films were facilely prepared by incorporating the natural mixed-dimensional palygorskite clay leached by oxalic acid (O-MDPal) into chitosan/polyvinylpyrrolidone (CS/PVP) matrix. By contrast, the obtained nanocomposite films exhibited the higher tensile strength (27.92 MPa), lower water contact angel (75.40°), better degradation, thermal stability and biocompatibility after incorporation of 20 wt% of O-MDPal, suggesting that O-MDPal contributed to enhancing the mechanical performance and water holding capacity of the CS/PVP nanocomposite films. Compared with the medical gauze and CS/PVP matrix groups, the nanocomposite films also indicated excellent hemostatic performance evaluated by blood loss and hemostasis time indexes based on the mouse tail amputation model, which might be ascribed to the enriched hemostatic functional sites, and hydrophilic surface, robust physical barrier role of nanocomposite films. Therefore, the nanocomposite film exhibited a promising practical application in wound healing.

Chitosan Nanocomposites as Wound Healing Materials: Advances in Processing Techniques and Mechanical Properties

This review discusses the increasing potential of chitosan nanocomposites as viable materials capable of targeting these debilitating factors. This review focuses on various techniques used to process chitosan nanocomposites and their mechanical properties. Chitosan nanocomposites are regarded as highly effective antimicrobials for the treatment of chronic wounds. Chitosan nanocomposites, such as chitosan/polyethylene and oxide/silica/ciprofloxacin, demonstrate efficient antibacterial activity and exhibit no cytotoxicity against Human Foreskin Fibroblast Cell Lines (HFF2). Other studies have also showcased the capacity of chitosan nanocomposites to accelerate and improve tissue regeneration through increment in the number of fibroblast cells and angiogenesis and reduction of the inflammation phase. The layer-by-layer technique has benefits, ensuring its suitability in preparing chitosan nanocomposites for drug delivery and wound dressing applications. While the co-precipitation route requires a cross-linker to achieve stability during processing, the solution-casting route can produce stable chitosan nanocomposites without a cross-linker. By using the solution casting method, fillers such as multi-walled carbon nanotubes (MWCNTs) and halloysite nanotubes (HTs) can be uniformly distributed in the chitosan, leading to improved mechanical properties. The antibacterial effects can be achieved with the introduction of AgNPs or ZnO. With the increasing understanding of the biological mechanisms that control these diseases, there is an influx in the introduction of novel materials into the mainstream wound care market.

Fabrication of Conductive Tissue Engineering Nanocomposite Films Based on Chitosan and Surfactant-Stabilized Graphene Dispersions

Chitosan (CS)/graphene nanocomposite films with tunable biomechanics, electroconductivity and biocompatibility using polyvinylpyrrolidone (PVP) and Pluronic F108 (Plu) as emulsion stabilizers for the purpose of conductive tissue engineering were successfully obtained. In order to obtain a composite solution, aqueous dispersions of multilayered graphene stabilized with Plu/PVP were supplied with CS at a ratio of CS to stabilizers of 2:1, respectively. Electroconductive films were obtained by the solution casting method. The electrical conductivity, mechanical properties and in vitro and in vivo biocompatibility of the resulting films were assessed in relation to the graphene concentration and stabilizer type and they were close to that of smooth muscle tissue. According to the results of the in vitro cytotoxicity analysis, the films did not release soluble cytotoxic components into the cell culture medium. The high adhesion of murine fibroblasts to the films indicated the absence of contact cytotoxicity. In subcutaneous implantation in Wistar rats, we found that stabilizers reduced the brittleness of the chitosan films and the inflammatory response.

Fabrication and evaluation of Cs/PVP sponge containing platelet-rich fibrin as a wound healing accelerator: An in vitro and in vivo study

Despite significant advances in surgery and postoperative care, there are still challenges in the treatment of wounds. In the current study, a freeze-dried chitosan (Cs)/polyvinylpyrrolidone (PVP) sponges containing platelet-rich fibrin (PRF at 1, 1.5 and 2% w/v) for wound dressing application is fabricated and fully characterized. Addition of 1% w/v of PRF to Cs/PVP (CS/PVP/1PRF) sample significantly increased the tensile strength (from 0.147 ± 0.005 to 0.242 ± 0.001 MPa), elastic modulus (from 0.414 ± 0.014 to 0.611 ± 0.022 MPa) and strain at break (from 53.4 ± 0.9 to 61.83 ± 1.17%) compared to Cs sample, and was hence selected as the optimal sample. The antibacterial activity of Cs/PVP/1PRF sponge wound dressing against E. coli and S. aureus was confirmed to be effective. Enzyme-linked immunosorbent assays revealed that the release of both VEGF and PDGF-AB from PRF powder, as well as PDGF-AB from Cs/PVP/1PRF sample was time-independent, but the release of VEGF from Cs/PVP/1PRF sample increased significantly with time. According to MTT and CAM assays, the Cs/PVP/1PRF sample significantly increased proliferation and angiogenic potential, respectively. Furthermore, in vivo studies demonstrated a 97.16 ± 1.55% wound closure for Cs/PVP/1PRF group after 14 days.

Extraction of cellulose nanocrystals from areca waste and its application in eco-friendly biocomposite film

Areca nut husk fibers are easily available and they are abundant agricultural waste, whose utilization to high value products needs more attention. The present study aims at the extraction of cellulose nanocrystals (CNCs) from areca nut husk fibers and the evaluation of its reinforcement capacity in polyvinyl alcohol (PVA) and chitosan (CS) film. The CNC showed rod-like structures, which were confirmed by TEM and AFM analysis. The diameter of the isolated CNC was 19 ± 3.3 nm; the length was about 195 ± 24 nm with an aspect ratio of 10.2 ± 6.8. The zeta potential of CNC was -15.3 ± 1.2 mV. Fourier Transform Infrared Spectroscopy analysis showed that the non-cellulosic compounds were effectively eliminated, and the X-ray diffraction results showed that CNC had higher crystallinity than the raw, alkali, and the bleached fibers. Thermogravimetric analysis revealed good thermal stability for the CNC. Moreover, the effects of the incorporation of CNC on the optical and tensile behaviours of the bionanocomposite film were investigated. The bionanocomposite film retained the same transparency as the PVA/CS film, indicating that the CNC was disseminated evenly in the film. The incorporation of CNC (3 wt%) to the PVA/CS film enhanced the tensile strength of the bionanocomposite film (9.46 ± 1.6 MPa) when compared to the control films (7.81 ± 1.4 MPa). Furthermore, the prepared nanobiocomposite film exhibited good antimicrobial activity against foodborne pathogenic bacteria and postharvest pathogenic fungi. These findings suggest that the bionanocomposite film might be suitable for food packaging applications.

Interface design of carbon filler/polymer composites for electromagnetic interference shielding

The main three methods of interface design for carbon/polymer composites for different carbon materials.

An upgraded and universal strategy to reinforce chitosan/polyvinylpyrrolidone film by incorporating active silica nanorods derived from natural palygorskite

Active silica nanorod (OPal) was prepared from natural palygorskite (RPal) using an updated acid leaching route, and then the effect of RPal and OPal as nano-filler on the network structure, mechanical, thermal and anti-aging properties of chitosan/polyvinylpyrrolidone (CS/PVP) films was studied comparatively. It was revealed that OPal had a better dispersibility than RPal in CS/PVP substrate, and its incorporation improved the mechanical properties and thermal stability of the films significantly. The optimal composite film containing OPal shows the maximum tensile strength of 27.53 MPa (only 14.87 MPa and 22.47 MPa for CS/PVP and CS/PVP/RPal films, respectively), resulting from the more uniform dispersion of OPal in polymer substrate and its stronger interaction with 3D polymer network. By a controllable acid-leaching process, the metal ions in octahedral sheets of RPal were dissolved out continuously, which is favorable to alleviate the adverse effects of variable metal ions on the film under UV light irradiation, and thus improve the aging-resistant ability of films. This study provides new ideas for improving the reinforcing ability of natural clay minerals towards biopolymer-based material, finds a new way to resolve the aging problem of polymer composites caused by incorporation of natural clay minerals.

Fabrication of chitosan/polyvinylpyrrolidone hydrogel scaffolds containing PLGA microparticles loaded with dexamethasone for biomedical applications

One of the most effective approaches for treatment of chronic rhinosinusitis is the use of hydrogel scaffolds with the sustained release of a given required drug. With this in mind, first, we synthesized and characterized poly (lactide-co-glycolide) (PLGA) micro and nano particles loaded with dexamethasone (DEX). We observed a 7-day release of DEX from nanoparticles, while the microparticles showed a 22-day release profile. Due to their slower rate of release, the PLGA microparticles loaded with DEX (PLGADEX microparticles) were specifically chosen for this study. As a second step, chitosan/polyvinylpyrrolidone (PVP) based hydrogels were prepared in various weight ratios and the PLGADEX microparticles were optimized in their structure based on variable gelation times. The morphological studies showed PLGADEX microparticles homogenously dispersed in the hydrogels. Moreover, the effect of weight ratio in the presence and absence of optimum percentage of PLGADEX microparticles was studied. The resultant hydrogels demonstrated a range of advantages, including good mechanical strength, porous morphology, amorphous structure, high swelling ratio, controlled biodegradability rate, and antibacterial activity. Additionally, a cytotoxicity analysis confirmed that the hydrogel scaffolds do not have adverse effects on the cells; our release studies in the hydrogel with the highest PVP content also showed 80% release after 30 days. Based on these results we were able to predict and control some of the mechanical properties, including the microstructure of the scaffolds, as well as the drug release, by optimizing the polymers - microparticle concentration, plus their resulting interactions. This optimized hydrogel can become part of a suitable alternative for treatment of allergic rhinitis and chronic sinusitis.

Polycaprolactone/polyvinylpyrrolidone coaxial electrospun fibers containing veratric acid-loaded chitosan nanoparticles for bone regeneration

Veratric acid (3,4-dimethoxy benzoic acid) (VA) is a hydrophobic phenolic phytocompound possessing therapeutic potential, but it has not been reported as actuating bone regeneration to date. Furthermore, delivery of hydrophobic compounds is often impeded in the body, thus depreciating their bioavailability. In this study, VA was found to have osteogenic potential and its sustained delivery was facilitated through a nanoparticle-embedded coaxial electrospinning technique. Polycaprolactone/polyvinylpyrrolidone (PCL/PVP) coaxial fibers were electrospun, encasing VA-loaded chitosan nanoparticles (CHS-NP). The fibers showed commendable physiochemical and material properties and were biocompatible with mouse mesenchymal stem cells (mMSCs). When mMSCs were grown on coaxial fibers, VA promoted these cells towards osteoblast differentiation as was reflected by calcium deposits. The mRNA expression of Runx2, an important bone transcriptional regulator, and other differentiation markers such as alkaline phosphatase, collagen type I, and osteocalcin were found to be upregulated in mMSCs grown on the PCL/PVP/CHS-NP-VA fibers. Overall, the study portrays the delivery of the phytocompound, VA, in a sustained manner to promote bone regeneration.

Improving the Performance of Feather Keratin/Polyvinyl Alcohol/Tris(hydroxymethyl)Aminomethane Nanocomposite Films by Incorporating Graphene Oxide or Graphene

In this study, feather keratin/polyvinyl alcohol/tris(hydroxymethyl)aminomethane (FK/PVA/Tris) bionanocomposite films containing graphene oxide (GO) (0.5, 1, 2, and 3 wt%) or graphene (0.5, 1, 2, and 3 wt%) were prepared using a solvent casting method. The scanning electron microscopy results indicated that the dispersion of GO throughout the film matrix was better than that of graphene. The successful formation of new hydrogen bonds between the film matrix and GO was confirmed through the use of Fourier-transform infrared spectroscopy. The tensile strength, elastic modulus, and initial degradation temperature of the films increased, whereas the total soluble mass, water vapor permeability, oxygen permeability, and light transmittance decreased following GO or graphene incorporation. In summary, nanoblending is an effective method to promote the application of FK/PVA/Tris-based blend films in the packaging field.

Fabrication of CS/GA/RGO/Pd composite hydrogels for highly efficient catalytic reduction of organic pollutants

In this study, natural polymer material chitosan (CS) and graphene oxide (GO) with large specific surface area were used to prepare a new CS/RGO-based composite hydrogel by using glutaraldehyde (GA) as cross-linking agent. In addition, a CS/GA/RGO/Pd composite hydrogel was prepared by loading palladium nanoparticles (Pd NPs). The morphologies and microstructures of the prepared hydrogels were characterized by SEM, TEM, XRD, TG, and BET. The catalytic performance of the CS/GA/RGO/Pd composite hydrogel was analyzed, and the experimental results showed that the CS/GA/RGO/Pd composite hydrogel had good catalytic performance for degradation of p-nitrophenol (4-NP) and o-nitroaniline (2-NA). Therefore, this study has potential application prospect in wastewater treatment and provides new information for composite hydrogel design.

New functional CS/GA/RGO/Pd composite hydrogels are prepared via a self-assembly process, demonstrating potential applications in catalysis as well as composite materials.

Characterizations and interfacial reinforcement mechanisms of multicomponent biopolymer based scaffold

It is difficult for a single component biopolymer to meet the requirements of scaffold at present. The development of multicomponent biopolymer based scaffold provides an effective method to solve the issue based on the advantages of each kind of the biomaterials. However, the compatibility between different components might be very poor due to the difficulties in forming strong interfacial bonding, and thereby significantly degrading the integrated mechanical properties of the scaffold. In recent years, interface phase introduction, surface modification and in situ growth have been the major strategies for enhancing interfacial bonding. This article presents a comprehensive overview on the research in the area of constructing multicomponent biopolymer based scaffold and reinforcing their interfacial properties, and more importantly, the interfacial bonding mechanisms are systematically summarized. Detailly, interface phase introduction can build a bridge between biopolymer and other components to form strong interface bonding with the two phases under the action of interface phase. Surface modification can graft organic molecules or polymers containing functional groups onto other components to crosslink with biopolymer. In situ growth can directly in situ synthesize other components with the action of nucleating agent serving as an adherent platform for the nucleation and growth of other components to biopolymer surface by chemical bonding. In addition, the mechanical properties (including strength and modulus) and biological properties (including bioactivity, cytocompatibility and biosensing in vitro, and tissue compatibility, bone regeneration capacity in vivo) of multicomponent biopolymer based scaffold after interfacial reinforcing are also reviewed and discussed. Finally, suggestions for further research are given with highlighting the need for specific investigations to assess the interface formation, structure, properties, and more in vivo studies of scaffold before applications.

Organophilic graphene nanosheets as a promising nanofiller for bio-based polyurethane nanocomposites: investigation of the thermal, barrier and mechanical properties

The present study focuses on the design of new nanocomposite films using bio-based thermoplastic polyurethane (TPU) as a polymer matrix and long chain amine functionalized reduced graphene oxide (G-ODA) as a nanofiller.

Sonochemical synthesis of PVA/PVP blend nanocomposite containing modified CuO nanoparticles with vitamin B1 and their antibacterial activity against Staphylococcus aureus and Escherichia coli

The aim of this paper was to blend the polymers, poly(N-vinyl-2-pyrrolidone) (PVP) and poly(vinyl alcohol) (PVA) to produce a novel composite materials possessing the benefits of both. CuO nanoparticles (NPs) were used as a suitable filler to fabricate the blend nanocomposites (NCs) with desired properties. First, the surface of NPs, was modified with vitamin B₁ (VB₁) as a bio-safe coupling agent. Then, the blend NCs with various ratios of modified CuO (3, 5, and 7 wt%) were fabricated under ultrasonic irradiations followed by casting/solvent evaporation method. These processes are fast and green way to disperse the NPs sufficiently. Several techniques were applied for the characterization of the obtained NCs. morphology examination demonstrated the morphology of NCs and compatibility of NPs with the blend polymer. EDX results indicated the weight and atomic percentage of the achieved materials. TGA analysis verified that the NCs show higher thermal properties than the neat blend polymer. Also embedding the modified NPs into the blend polymer had effected on optical absorbance of the obtained NCs. The contact angle measurements confirmed that the hydrophilicity decreased for different proportions of the modified NPs loaded in the blend polymer. Finally, NCs show better bactericidal effects against gram-positive than gram-negative bacteria.

Graphene Oxide Filled Lignin/Starch Polymer Bionanocomposite: Structural, Physical, and Mechanical Studies

In this study, graphene oxide (GO) was investigated as a potential nanoreinforcing agent in starch/lignin (ST/L) biopolymer matrix. Bionanocomposite films based on ST/L blend matrix and GO were prepared by solution-casting technique of the corresponding film-forming solution. The structures, morphologies, and properties of bionanocomposite films were characterized by Fourier transform infrared (FTIR), thermal gravimetric analysis (TGA), ultraviolet-visible (UV-vis), SEM, and tensile tests. The experimental results showed that content of GO have a significant influence on the mechanical properties of the produced films. The results revealed that the interfacial interaction formed in the bionanocomposite films improved the compatibility between GO fillers and ST/L matrix. The addition of GO also reduced moisture uptake (Mu) and water vapor permeability of ST/L blend film. In addition, TGA showed that the thermal stability of bionanocomposite films was better than that of neat starch film. These findings confirmed the effectiveness of the proposed approach to produce biodegradable films with enhanced properties, which may be used in packaging applications.

Antimicrobial Bamboo Materials Functionalized with ZnO and Graphene Oxide Nanocomposites

Bamboo materials with improved antibacterial performance based on ZnO and graphene oxide (GO) were fabricated by vacuum impregnation and hydrothermal strategies. The Zn2+ ions and GO nanosheets were firstly infiltrated into the bamboo structure, followed by dehydration and crystallization upon hydrothermal treatment, leading to the formation of ZnO/GO nanocomposites anchored in the bulk bamboo. The bamboo composites were characterized by several techniques including scanning electron microscopy (SEM), Fourier transform infrared spectra (FTIR), and X-ray diffraction (XRD), which confirmed the existence of GO and ZnO in the composites. Antibacterial performances of bamboo samples were evaluated by the bacteriostatic circle method. The introduction of ZnO/GO nanocomposites into bamboo yielded ZnO/GO/bamboo materials which exhibited significant antibacterial activity against Escherichia coli (E. coli, Gram-negative) and Bacillus subtilis (B. subtilis, Gram-positive) bacteria and high thermal stability. The antimicrobial bamboo would be expected to be a promising material for the application in the furniture, decoration, and construction industry.

Bioinspired, Ultrastrong, Highly Biocompatible, and Bioactive Natural Polymer/Graphene Oxide Nanocomposite Films

Tough and biocompatible nanocomposite films: A new type of bioinspired ultrastrong, highly biocompatible, and bioactive konjac glucomannan (KGM)/graphene oxide (GO) nanocomposite film is fabricated on a large scale by a simple solution-casting method. Such KGM-GO composite films exhibit much enhanced mechanical properties under the strong hydrogen-bonding interactions, showing great potential in the fields of tissue engineering and food package.

Anti-bacterial performances and biocompatibility of bacterial cellulose/graphene oxide composites

Bacterial cellulose/graphene oxide composites have excellent anti-bacterial activities and good compatibility.