Synergistic effects of flow and interfaces on antibody aggregation

Microfluidic Stress Device to Decouple the Synergistic Effect of Shear and Interfaces on Antibody Aggregation

Protein denaturation and aggregation resulting from the effects of interfacial stress, often enhanced by flow and shear stress, pose significant challenges in the production of therapeutic proteins and monoclonal antibodies. The influence of flow on protein stability is closely intertwined with interfacial effects. In this study, we have developed a microfluidic device capable of exposing low volume (< 320 µL) protein solutions to highly uniform shear. To disentangle the synergistic impact of flow and interfaces on protein aggregation, we fabricated two devices composed of different materials, namely poly(methyl methacrylate) (PMMA) and stainless steel. Upon application of shear, we observed formation of protein particles in the micron-size range. Notably, The number of particles generated in the steel devices was ∼ 3.5 fold lower than in the PMMA device, hinting at an interface-mediated effect. With increasing the protein concentration from 1 to 50 mg/mL we observed a saturation in the amount of aggregates, further confirming the key role of solid-liquid interfaces in inducing particle formation. Introduction of non-ionic surfactants prevented protein aggregation, even at the highest tested protein concentration and low surfactant concentrations of 0.05 mg/mL. Overall, our findings corroborate the synergistic impact of shear and interface effects on protein aggregation. The device developed in this study offers a small-scale platform for assessing the stability of antibody formulations throughout various stages of the development and manufacturing process.

Understanding the Impact of Combined Hydrodynamic Shear and Interfacial Dilatational Stress, on Interface-Mediated Particle Formation for Monoclonal Antibody Formulations

During biomanufacturing, several unit operations expose solutions of biologics to multiple stresses, such as hydrodynamic shear forces due to fluid flow and interfacial dilatational stresses due to mechanical agitation or bubble collapse. When these stresses individually act on proteins adsorbed to interfaces, it results in an increase in protein particles in the bulk solution, a phenomenon referred to as interface-induced protein particle formation. However, an understanding of the dominant cause, when multiple stresses are acting simultaneously or sequentially, on interface-induced protein particle formation is limited. In this work, we established a unique set-up using a peristaltic pump and a Langmuir-Pockels trough to study the impact of hydrodynamic shear stress due to pumping and interfacial dilatational stress, on protein particle formation. Our experimental results together demonstrate that for protein solutions subjected to various combinations of stress (i.e., interfacial and hydrodynamic stress in different sequences), surface pressure values during adsorption and when subjected to compression/dilatational stresses, showed no change, suggesting that the interfacial properties of the protein film are not impacted by pumping. The concentration of protein particles is an order of magnitude higher when interfacial dilatational stress is applied at the air-liquid interface, compared to solutions that are only subjected to pumping. Furthermore, the order in which these stresses are applied, have a significant impact on the concentration of protein particles measured in the bulk solution. Together, these studies conclude that for biologics exposed to multiple stresses throughout bioprocessing and manufacturing, exposure to air-liquid interfacial dilatational stress is the predominant mechanism impacting protein particle formation at the interface and in the bulk solution.

Transportation of mAb Dosing Solution in Intravenous Bag: Impact of Manual, Vehicle, and Pneumatic Tube System Transportation Methods on Product Quality

Monoclonal antibody (mAb) products for intravenous (IV) administration generally require aseptic compounding with a commercial diluent within a pharmacy. The prepared dosing solution in the IV bag may be transported to the dosing location via manual, vehicular, pneumatic tube system (PTS), or a combination of these methods. In this study, the type and level of physical stresses associated with these three methods and their product quality impact for relatively sensitive and stable mAbs were assessed. Vibration was found to be the main stress associated with manual and vehicle transportation methods, although this was at a relatively low level (<1 GRMS/Root-Mean-Square Acceleration). Shock and drop events, at relatively low levels, were also observed with these methods. PTS transportation showed substantially more intense shock, vibration, and drop stresses and the measured levels were up to 91 G/force of acceleration or deceleration, 3.7 GRMS and 39 G, respectively. Using a foam padding insert for PTS transportation reduced the shock level considerably (91 G to 59 G). Transportation of mAb dosing solutions in IV bags via different methods including PTS transportation variables caused a small increase in the subvisible particle counts and there was no change in submicrometer particle distribution. No visible particles and no significant change to soluble aggregate levels were observed after transportation. Strategies such as removal of IV bag headspace prior to transport and in-line filtration poststress reduced the subvisible particles counts. All tested transportation conditions showed negligible impact on other product quality attributes tested. Removal of IV bag headspace prior to PTS transport prevented formation of micro air bubbles and foaming compared to the unaltered IV bag. This study shows examples where manual, vehicle, and PTS transport methods did not significantly impact product quality, and provides evidence that mAb products that are appropriately stabilized in the dosing solution (e.g., with a surfactant) can be transported via a PTS.

Effects of sound energy on proteins and their complexes

Mechanical energy in the form of ultrasound and protein complexes intuitively have been considered as two distinct unrelated topics. However, in the past few years, increasingly more attention has been paid to the ability of ultrasound to induce chemical modifications on protein molecules that further change protein-protein interaction and protein self-assembling behavior. Despite efforts to decipher the exact structure and the behavior-modifying effects of ultrasound on proteins, our current understanding of these aspects remains limited. The limitation arises from the complexity of both phenomena. Ultrasound produces multiple chemical, mechanical, and thermal effects in aqueous media. Proteins are dynamic molecules with diverse complexation mechanisms. This review provides an exhaustive analysis of the progress made in better understanding the role of ultrasound in protein complexation. It describes in detail how ultrasound affects an aqueous environment and the impact of each effect separately and when combined with the protein structure and fold, the protein-protein interaction, and finally the protein self-assembly. It specifically focuses on modifying role of ultrasound in amyloid self-assembly, where the latter is associated with multiple neurodegenerative disorders.

Application of Formulation Principles to Stability Issues Encountered During Processing, Manufacturing, and Storage of Drug Substance and Drug Product Protein Therapeutics

The field of formulation and stabilization of protein therapeutics has become rather extensive. However, most of the focus has been on stabilization of the final drug product. Yet, proteins experience stress and degradation through the manufacturing process, starting with fermentaition. This review describes how formulation principles can be applied to stabilize biopharmaceutical proteins during bioprocessing and manufacturing, considering each unit operation involved in prepration of the drug substance. In addition, the impact of the container on stabilty is discussed as well.

Comparison of the Protective Effect of Polysorbates, Poloxamer and Brij on Antibody Stability Against Different Interfaces

Therapeutic proteins and antibodies are exposed to a variety of interfaces during their lifecycle, which can compromise their stability. Formulations, including surfactants, must be carefully optimized to improve interfacial stability against all types of surfaces. Here we apply a nanoparticle-based approach to evaluate the instability of four antibody drugs against different solid-liquid interfaces characterized by different degrees of hydrophobicity. We considered a model hydrophobic material as well as cycloolefin-copolymer (COC) and cellulose, which represent some of the common solid-liquid interfaces encountered during drug production, storage, and delivery. We assess the protective effect of polysorbate 20, polysorbate 80, Poloxamer 188 and Brij 35 in our assay and in a traditional agitation study. While all nonionic surfactants stabilize antibodies against the air-water interface, none of them can protect against hydrophilic charged cellulose. Polysorbates and Brij increase antibody stability in the presence of COC and the model hydrophobic interface, although to a lesser extent compared to the air-water interface, while Poloxamer 188 has a negligible stabilizing effect against these interfaces. These results highlight the challenge of fully protecting antibodies against all types of solid-liquid interfaces with traditional surfactants. In this context, our high-throughput nanoparticle-based approach can complement traditional shaking assays and assist in formulation design to ensure protein stability not only at air-water interfaces, but also at relevant solid-liquid interfaces encountered during the product lifecycle.

Interfacial Adsorption Controls Particle Formation in Antibody Formulations Subjected to Extensional Flows and Hydrodynamic Shear

During their manufacturing and delivery to patients, therapeutic proteins are commonly exposed to various interfaces and to hydrodynamic shear forces. Although adsorption of proteins to solid-liquid interfaces is known to foster formation of protein aggregates and particles, the impact of shear remains controversial, in part because of experimental challenges in separating the effects of shear from those caused by simultaneous exposure to interfaces. Extensional flows (occurring when solutions flow through sudden contractions) exert localized elongational forces that have been suspected to be damaging to proteins. In this work, we measured aggregation and particle formation in formulations of polyclonal and monoclonal antibodies subjected to extensional flow, high shear (105 s-1) and exposure to stainless-steel/water interfaces. Modification of the surface charge at the stainless steel/water interface changed protein adsorption characteristics without altering shear profiles, enabling shear and interfacial interactions to be separated. Even under conditions where antibodies were subjected to high hydrodynamic shear and extensional flow, production of subvisible particles could be inhibited by modifying the stainless-steel surface charge to minimize antibody adsorption. Digital images of particles recorded by flow imaging microscopy (FIM) and analyzed with machine learning algorithms were consistent with a particle formation mechanism by which antibodies adsorb and aggregate at the stainless-steel/water interface and subsequently form particles when shear displaces the interfacial aggregates, transporting them into the bulk solution. Topographical differences measured using atomic force microscopy (AFM) supported the proposed mechanism by showing reduced levels of protein adsorption on surface-charge-modified stainless-steel.

Water loss from silicone tubing and effect on protein concentration during drug product manufacturing

Silicone tubing is used in various unit operations during drug product (DP) manufacturing. Hold of protein formulations in silicone tubing over time may have an impact on product quality, particularly protein concentration. This study evaluated the change in protein concentration of a test monoclonal antibody (mAb) formulation over various hold times in silicone tubing as a function of tubing internal diameter (ID) and wall thickness. It was hypothesized that the rate of water diffusion through the semi-permeable membrane is a function of the tubing ID and wall thickness. The weight and protein concentration of various formulation-filled tubings over time was measured. The weight of water lost varied linearly with the change in protein concentration. It was observed to be independent of mAb type, formulation composition, and initial protein concentration for a given tubing ID and wall thickness. The effect of formulation water activity on the water loss rate was investigated. A mechanistic diffusion-based model was developed that predicts the change in tubing weight and therefore protein concentration over various hold times for a given formulation and tubing. Overall, this study suggests that water loss from silicone tubing affects protein concentration and should be monitored during DP process development and manufacturing.

Relationship between aggregation of therapeutic proteins and agitation parameters: Acceleration and frequency

An increase in protein aggregates during transportation should be suppressed in therapeutic protein products because the aggregates have a potential risk of immunogenicity. In this study, three protein solutions in vials were exposed to tri-axial vibration with various combinations of frequency and acceleration using a transportation test system to investigate the relationship between low g-force stresses and protein aggregate generation. The number concentration of micron aggregates detected by flow imaging analysis increased markedly when the acceleration and frequency of agitation were within a specific range, in other words, above a threshold. This threshold was common among the three protein solutions. The suppression of micron aggregate formation by adding a surfactant suggested that agitation above the threshold increased micron aggregates mainly via interface-mediated routes. Notably, agitation, including agitation below the threshold, accelerated spontaneous oligomerization (nanometer aggregate generation) of proteins in bulk solution even in the presence of the surfactant. Studies of stability against mechanical stresses (e.g., a random vibration test to simulate actual shipment, with a time-compressed setting by increasing acceleration) need to be performed and discussed with careful consideration of the threshold for generating micron aggregates.

Surface-Induced Protein Aggregation and Particle Formation in Biologics: Current Understanding of Mechanisms, Detection and Mitigation Strategies

Protein stability against aggregation is a major quality concern for the production of safe and effective biopharmaceuticals. Amongst the different drivers of protein aggregation, increasing evidence indicates that interactions between proteins and interfaces represent a major risk factor for the formation of protein aggregates in aqueous solutions. Potentially harmful surfaces relevant to biologics manufacturing and storage include air-water and silicone oil-water interfaces as well as materials from different processing units, storage containers, and delivery devices. The impact of some of these surfaces, for instance originating from impurities, can be difficult to predict and control. Moreover, aggregate formation may additionally be complicated by the simultaneous presence of interfacial, hydrodynamic and mechanical stresses, whose contributions may be difficult to deconvolute. As a consequence, it remains difficult to identify the key chemical and physical determinants and define appropriate analytical methods to monitor and predict protein instability at these interfaces. In this review, we first discuss the main mechanisms of surface-induced protein aggregation. We then review the types of contact materials identified as potentially harmful or detected as potential triggers of proteinaceous particle formation in formulations and discuss proposed mitigation strategies. Finally, we present current methods to probe surface-induced instabilities, which represent a starting point towards assays that can be implemented in early-stage screening and formulation development of biologics.

An Intra-Company Analysis of Inherent Particles in Biologicals Shapes the Protein Particle Mitigation Strategy Across Development Stages

To better understand protein aggregation and inherent particle formation in the biologics pipeline at Novartis, a cross-functional team collected and analyzed historical protein particle issues. Inherent particle occurrences from the past 10 years were systematically captured in a protein particle database. Where the root cause was identified, a number of product attributes (such as development stage, process step, or protein format) were trended. Several key themes were revealed: 1) there was a higher propensity for inherent particle formation with non-mAbs than with mAbs; 2) the majority of particles were detected following manufacturing at scale, and were not predicted by the small-scale studies; 3) most issues were related to visible particles, followed by subvisible particles; 4) 50% of the issues were manufacturing related. These learnings became the foundation of a particle mitigation strategy across development and technical transfer, and resulted in a set of preventive actions. Overall, this study provides further insight into a recognized industry challenge and hopes to inspire the biopharmaceutical industry to transparently share their experiences with inherent particles formation.

A proteome scale study reveals how plastic surfaces and agitation promote protein aggregation

Protein aggregation in biotherapeutics can reduce their activity and effectiveness. It may also promote immune reactions responsible for severe adverse effects. The impact of plastic materials on protein destabilization is not totally understood. Here, we propose to deconvolve the effects of material surface, air/liquid interface, and agitation to decipher their respective role in protein destabilization and aggregation. We analyzed the effect of polypropylene, TEFLON, glass and LOBIND surfaces on the stability of purified proteins (bovine serum albumin, hemoglobin and α-synuclein) and on a cell extract composed of 6000 soluble proteins during agitation (P = 0.1-1.2 W/kg). Proteomic analysis revealed that chaperonins, intrinsically disordered proteins and ribosomes were more sensitive to the combined effects of material surfaces and agitation while small metabolic oligomers could be protected in the same conditions. Protein loss observations coupled to Raman microscopy, dynamic light scattering and proteomic allowed us to propose a mechanistic model of protein destabilization by plastics. Our results suggest that protein loss is not primarily due to the nucleation of small aggregates in solution, but to the destabilization of proteins exposed to material surfaces and their subsequent aggregation at the sheared air/liquid interface, an effect that cannot be prevented by using LOBIND tubes. A guidance can be established on how to minimize these adverse effects. Remove one of the components of this combined stress - material, air (even partially), or agitation - and proteins will be preserved.

Machine Learning Analysis Provides Insight into Mechanisms of Protein Particle Formation Inside Containers During Mechanical Agitation

Container choice can influence particle generation within protein formulations. Incompatibility between proteins and containers can manifest as increased particle concentrations, shifts in particle size distributions and changes in particle morphology distributions. In this study, flow imaging microscopy (FIM) combined with machine learning-based goodness-of-fit hypothesis testing algorithms were used in accelerated stability studies to investigate the impact of containers on particle formation. Containers in four major container categories subdivided into eleven container types were filled with monoclonal antibody formulations and agitated with and without headspace, producing subvisible particles. Digital images of the particles were recorded using flow imaging microscopy and analyzed with machine learning algorithms. Particle morphology distributions depended on container category and type, revealing differences that would not have been obvious by analysis of particle concentrations or container surface characteristics alone. Additionally, the algorithm was used to compare morphologies of particles generated in containers against those generated using isolated stresses at air-liquid and container-air-liquid interfaces. These comparisons showed that the morphology distributions of particles formed during agitation most closely resemble distributions that result from exposure of proteins to moving triple interface lines at points where container-air-liquid interfaces intersect. The approach described here can be used to identify dominant causes of particle generation due to protein-container interactions.

Reaching the breaking point: Effect of tubing characteristics on protein particle formation during peristaltic pumping

Peristaltic pumping has been identified as a cause for protein particle formation during manufacturing of biopharmaceuticals. To give advice on tubing selection, we evaluated the physicochemical parameters and the propensity for tubing and protein particle formation using a monoclonal antibody (mAb) for five different tubings. After pumping, particle levels originating from tubing and protein differed substantially between the tubing types. An overall low shedding of tubing particles by wear was linked to low surface roughness and high abrasion resistance. The formation of mAb particles upon pumping was dependent on the tubing hardness and surface chemistry. Defined stretching of tubing filled with mAb solution revealed that aggregation increased with higher strain beyond the breaking point of the protein film adsorbed to the tubing wall. This is in line with the decrease in protein particle concentration with increasing tubing hardness. Furthermore, material composition influenced particle formation propensity. Faster adsorption to materials with higher hydrophobicity is suspected to lead to a higher protein film renewal rate resulting in higher protein particle counts. Overall, silicone tubing with high hardness led to least protein particles during peristaltic pumping. Results from this study emphasize the need of proper tubing selection to minimize protein particle generation upon pumping.

Morphological integrity of insulin amyloid-like aggregates depends on preparation methods and post-production treatments

Protein aggregates are often varying extensively in their morphological characteristics, which may lead to various biological outcomes, such as increased immunogenicity risk. However, isolation of aggregates with a specific morphology within an ensemble is often challenging. To gain vital knowledge on the effects of aggregate characteristics, samples containing a single morphology must be produced by direct control of the aggregation process. Moreover, the formed aggregates need to be in an aqueous solution suitable for biological assays, while keeping their morphology intact. Here we evaluated the dependence of morphology and integrity of amyloid-like fibrils and spherulites on preparation conditions and post-treatment methods. Samples containing either amyloid-like fibrils or spherulites produced from human insulin in acetic acid solutions are dependent on the presence of salt (NaCl). Moreover, mechanical shaking (600 rpm) inhibits spherulite formation, while only affecting the length of the formed fibrils compared to quiescent conditions. Besides shaking, the initial protein concentration in the formulation was found to control fibril length. Surprisingly, exchanging the solution used for aggregate formation to a physiologically relevant buffer, had a striking effect on the morphological integrity of the fibril and spherulite samples. Especially the secondary structure of one of our spherulite samples presented dramatic changes of the aggregated β-sheet content after exchanging the solution, emphasizing the importance of the aggregate stability. These results and considerations have profound implications on the data interpretation and should be implemented in the workflow for both fundamental characterization of aggregates as well as assays for evaluation of their corresponding biological effects.

Insulin aggregation starts at dynamic triple interfaces, originating from solution agitation

The consequences of agitation on protein stability are particularly relevant to therapeutic proteins. However, the precise contribution of the different effects induced by agitation in pathways leading to protein denaturation and aggregation at interfaces is not entirely understood. In particular, the contribution of a moving triple line, induced by the sweeping of a solution meniscus on a container wall upon agitation, has only been rarely assessed. In this article, we therefore designed experimental setups to analyze how mixing, shear stress, and dynamic triple interfaces influence insulin aggregation in physiological conditions. This has been achieved by controlling agitation speed, shear stress, and the extension of triple interfaces in order to shed light on the contribution of different agitation-induced effects on insulin aggregation in physiological conditions. We demonstrate that strong agitation is necessary for the onset of insulin aggregation, while the growth of the aggregates is sustained even under weak agitation. Kinetic insulin aggregation studies in conditions of intermittent wetting show that the aggregation rate correlates with the amount of dynamic triple interfaces that the proteins are exposed to. Finally, we demonstrate that the triple line, where the protein solution, the air, and a hydrophobic surface meet constitutes a preferential early aggregation site.

Emerging Challenges and Innovations in Surfactant-mediated Stabilization of Biologic Formulations

Biologics may be subjected to various destabilizing conditions during manufacturing, transportation, storage, and use. Therefore, biologics must be appropriately formulated to meet their desired quality target product profiles. In the formulations of protein-based biologics, one critical component is surfactant. Polysorbate 80 and Polysorbate 20 remain the most commonly used surfactants. Surfactants can stabilize proteins through different mechanisms and help the proteins withstand destabilization stresses. However, the challenges associated with surfactants, for instance, impurities, degradation, and potential triggering of adverse immune responses, have been encountered. Therefore, there are continued efforts to develop novel surfactants to overcome these challenges associated with traditional surfactants. Meanwhile, surfactants have also found their use in formulations of newer and novel modalities, namely, antibody-drug conjugates, bispecific antibodies, and adeno-associated viruses (AAV). This review provides an updated in-depth discussion of surfactants in the above-mentioned areas, namely mechanism of action of surfactants, a critical review of challenges with surfactants and current mitigation approaches, and emerging technologies to develop novel surfactants. In addition, gaps, current mitigations, and future directions have been presented to trigger further discussion and research to facilitate the use and development of novel surfactants.

Stress Factors in Protein Drug Product Manufacturing and Their Impact on Product Quality

Injectable protein-based medicinal products (drug products, or DPs) must be produced by using sterile manufacturing processes to ensure product safety. In DP manufacturing the protein drug substance, in a suitable final formulation, is combined with the desired primary packaging (e.g., syringe, cartridge, or vial) that guarantees product integrity and enables transportation, storage, handling and clinical administration. The protein DP is exposed to several stress conditions during each of the unit operations in DP manufacturing, some of which can be detrimental to product quality. For example, particles, aggregates and chemically-modified proteins can form during manufacturing, and excessive amounts of these undesired variants might cause an impact on potency or immunogenicity. Therefore, DP manufacturing process development should include identification of critical quality attributes (CQAs) and comprehensive risk assessment of potential protein modifications in process steps, and the relevant steps must be characterized and controlled. In this commentary article we focus on the major unit operations in protein DP manufacturing, and critically evaluate each process step for stress factors involved and their potential effects on DP CQAs. Moreover, we discuss the current industry trends for risk mitigation, process control including analytical monitoring, and recommendations for formulation and process development studies, including scaled-down runs.

Rapid aggregation of therapeutic monoclonal antibodies by bubbling induced air/liquid interfacial and agitation stress at different conditions

Degradation of therapeutic monoclonal antibodies (mAb) due to interfacial agitation through air bubbling was investigated. Samples containing mAb in phosphate buffered saline were subjected to rapid bubbling by using a peristaltic pump at an air flow rate of 11.5 mL/min. Samples were analyzed by visual observation, UV-Vis, fluorescence, circular dichroism and infrared spectroscopy, size-exclusion chromatography (SEC), dynamic light scattering, microscopy, and cell-based activity assays. The stressed samples showed increasing turbidity with bubbling time, with mAb1 showing a protein loss of 53% in the supernatant at the latest time point (240 min), indicating formation of sub-visible and visible aggregates. Aggregate rich samples exhibited altered secondary structure and higher hydrophobicity with 40% reduction in activity. The supernatants of the stressed samples showed unchanged secondary and tertiary structure without the presence of any oligomers in SEC. Furthermore, the impact of various factors that could affect aggregation was investigated and it was found that the extent of aggregation was affected by protein concentration, sample volume, presence of surfactants, temperature, air flow rate, and presence of silicone oil. In conclusion, exposure to air/liquid interfacial stress through bubbling into liquid mAb samples effectively generated sub-visible and visible aggregates, making air bubbling an attractive approach for interfacial stress degradation studies of mAbs.

An accelerated surface-mediated stress assay of antibody instability for developability studies

High physical stability is required for the development of monoclonal antibodies (mAbs) into successful therapeutic products. Developability assays are used to predict physical stability issues such as high viscosity and poor conformational stability, but protein aggregation remains a challenging property to predict. Among different types of stresses, air–water and solid–liquid interfaces are well known to potentially trigger protein instability and induce aggregation. Yet, in contrast to the increasing number of developability assays to evaluate bulk properties, there is still a lack of experimental methods to evaluate antibody stability against interfaces. Here, we investigate the potential of a hydrophobic nanoparticle surface-mediated stress assay to assess the stability of mAbs during the early stages of development. We evaluate this surface-mediated accelerated stability assay on a rationally designed library of 14 variants of a humanized IgG4, featuring a broad span of solubility values and other developability properties. The assay could identify variants characterized by high instability against agitation in the presence of air–water interfaces. Remarkably, for the set of investigated molecules, we observe strong correlations between the extent of aggregation induced by the surface-mediated stress assay and other developability properties of the molecules, such as aggregation upon storage at 45°C, self-association (evaluated by affinity-capture self-interaction nanoparticle spectroscopy) and nonspecific interactions (estimated by cross-interaction chromatography, stand-up monolayer chromatography (SMAC), SMAC*). This highly controlled surface-mediated stress assay has the potential to complement and increase the ability of the current set of screening techniques to assess protein aggregation and developability potential of mAbs during the early stages of drug development.

Abbreviations:AC-SINS: Affinity-Capture Self-Interaction Nanoparticle Spectroscopy; AMS: Ammonium sulfate precipitation; ANS: 1-anilinonaphtalene-8-sulfonate; CIC: Cross-interaction chromatography; DLS: Dynamic light scattering; HIC: Hydrophobic interaction chromatography; HNSSA: Hydrophobic nanoparticles surface-stress assay; mAb: Monoclonal antibody; NP: Nanoparticle; SEC: Size exclusion chromatography; SMAC: Stand-up monolayer chromatography; WT: Wild type

Size-based Degradation of Therapeutic Proteins - Mechanisms, Modelling and Control

Protein therapeutics are in great demand due to their effectiveness towards hard-to-treat diseases. Despite their high demand, these bio-therapeutics are very susceptible to degradation via aggregation, fragmentation, oxidation, and reduction, all of which are very likely to affect the quality and efficacy of the product. Mechanisms and modelling of these degradation (aggregation and fragmentation) pathways is critical for gaining a deeper understanding of stability of these products. This review aims to provide a summary of major developments that have occurred towards unravelling the mechanisms of size-based protein degradation (particularly aggregation and fragmentation), modelling of these size-based degradation pathways, and their control. Major caveats that remain in our understanding and control of size-based protein degradation have also been presented and discussed.

Adsorbed protein film on pump surfaces leads to particle formation during fill-finish manufacturing

During fill-finish manufacturing, therapeutic proteins may aggregate or form subvisible particles in response to the physical stresses encountered within filling pumps. Understanding and quantitating this risk is important since filling may be the last unit operation before the patient receives their dose. We studied particle formation from lab-scale to manufacturing-scale using sensitive and robust protein formulations. Filling experiments with a ceramic rotary piston pump were integrated with a rinse-stripping method to investigate the relationship between protein adsorption and particle formation. For a sensitive protein, multilayer film formation on the piston surface correlated with high levels of subvisible particles in solution. For a robust protein formulation, adsorption and subvisible particle formation were minimal. These results support an aggregation mechanism that is initiated by adsorption to pump surfaces and propagated by mechanical and/or hydrodynamic disruption of the film. The elemental analysis confirmed that ceramic wear debris remained at trace levels and did not contribute appreciably to protein aggregation.

2D and 3D inkjet printing of biopharmaceuticals - A review of trends and future perspectives in research and manufacturing

There is an ongoing global shift in pharmaceutical business models from small molecule drugs to biologics. This increase in complexity is in response to advancements in our diagnoses and understanding of diseases. With the more targeted approach coupled with its inherently more costly development and manufacturing, 2D and 3D printing are being explored as suitable techniques to deliver more personalised and affordable routes to drug discovery and manufacturing. In this review, we explore first the business context underlying this shift to biopharmaceuticals and provide an update on the latest work exploring discovery and pharmaceutics. We then draw on multiple disciplines to help reveal the shared challenges facing researchers and firms aiming to develop biopharmaceuticals, specifically when using the most commonly explored manufacturing routes of drop-on-demand inkjet printing and pneumatic extrusion. This includes separating out how to consider mechanical and chemical influences during manufacturing, the role of the chosen hardware and the challenges of aqueous formulation based on similar challenges being faced by the printing industry. Together, this provides a review of existing work and guidance for researchers and industry to help with the de-risking and rapid development of future biopharmaceutical products.

The role of surfaces on amyloid formation

Interfaces can strongly accelerate or inhibit protein aggregation, destabilizing proteins that are stable in solution or, conversely, stabilizing proteins that are aggregation-prone. Although this behaviour is well-known, our understanding of the molecular mechanisms underlying surface-induced protein aggregation is still largely incomplete. A major challenge is represented by the high number of physico-chemical parameters involved, which are highly specific to the considered combination of protein, surface properties, and solution conditions. The key aspect determining the role of interfaces is the relative propensity of the protein to aggregate at the surface with respect to bulk. In this review, we discuss the multiple molecular determinants that regulate this balance. We summarize current experimental techniques aimed at characterizing protein aggregation at interfaces, and highlight the need to complement experimental analysis with theoretical modelling. In particular, we illustrate how chemical kinetic analysis can be combined with experimental methods to provide insights into the molecular mechanisms underlying surface-induced protein aggregation, under both stagnant and agitation conditions. We summarize recent progress in the study of important amyloids systems, focusing on selected relevant interfaces.

Environmental Control of Amyloid Polymorphism by Modulation of Hydrodynamic Stress

The phenomenon of amyloid polymorphism is a key feature of protein aggregation. Unravelling this phenomenon is of great significance for understanding the underlying molecular mechanisms associated with neurodegenerative diseases and for the development of amyloid-based functional biomaterials. However, the understanding of the molecular origins and the physicochemical factors modulating amyloid polymorphs remains challenging. Herein, we demonstrate an association between amyloid polymorphism and environmental stress in solution, induced by an air/water interface in motion. Our results reveal that low-stress environments produce heterogeneous amyloid polymorphs, including twisted, helical, and rod-like fibrils, whereas high-stress conditions generate only homogeneous rod-like fibrils. Moreover, high environmental stress converts twisted fibrils into rod-like fibrils both in-pathway and after the completion of mature amyloid formation. These results enrich our understanding of the environmental origin of polymorphism of pathological amyloids and shed light on the potential of environmentally controlled fabrication of homogeneous amyloid biomaterials for biotechnological applications.

Shear-Induced Amyloid Aggregation in the Brain: V. Are Alzheimer's and Other Amyloid Diseases Initiated in the Lower Brain and Brainstem by Cerebrospinal Fluid Flow Stresses?

Amyloid-β (Aβ) and tau oligomers have been identified as neurotoxic agents responsible for causing Alzheimer's disease (AD). Clinical trials using Aβ and tau as targets have failed, giving rise to calls for new research approaches to combat AD. This paper provides such an approach. Most basic AD research has involved quiescent Aβ and tau solutions. However, studies involving laminar and extensional flow of proteins have demonstrated that mechanical agitation of proteins induces or accelerates protein aggregation. Recent MRI brain studies have revealed high energy, chaotic motion of cerebrospinal fluid (CSF) in lower brain and brainstem regions. These and studies showing CSF flow within the brain have shown that there are two energetic hot spots. These are within the third and fourth brain ventricles and in the neighborhood of the circle of Willis blood vessel region. These two regions are also the same locations as those of the earliest Aβ and tau AD pathology. In this paper, it is proposed that cardiac systolic pulse waves that emanate from the major brain arteries in the lower brain and brainstem regions and whose pulse waves drive CSF flows within the brain are responsible for initiating AD and possibly other amyloid diseases. It is further proposed that the triggering of these diseases comes about because of the strengthening of systolic pulses due to major artery hardening that generates intense CSF extensional flow stress. Such stress provides the activation energy needed to induce conformational changes of both Aβ and tau within the lower brain and brainstem region, producing unique neurotoxic oligomer molecule conformations that induce AD.

Analysis of biomolecular condensates and protein phase separation with microfluidic technology

An increasing body of evidence shows that membraneless organelles are key components in cellular organization. These observations open a variety of outstanding questions about the physico-chemical rules underlying their assembly, disassembly and functions. Some molecular determinants of biomolecular condensates are challenging to probe and understand in complex in vivo systems. Minimalistic in vitro reconstitution approaches can fill this gap, mimicking key biological features, while maintaining sufficient simplicity to enable the analysis of fundamental aspects of biomolecular condensates. In this context, microfluidic technologies are highly attractive tools for the analysis of biomolecular phase transitions. In addition to enabling high-throughput measurements on small sample volumes, microfluidic tools provide for exquisite control of self-assembly in both time and space, leading to accurate quantitative analysis of biomolecular phase transitions. Here, with a specific focus on droplet-based microfluidics, we describe the advantages of microfluidic technology for the analysis of several aspects of phase separation. These include phase diagrams, dynamics of assembly and disassembly, rheological and surface properties, exchange of materials with the surrounding environment and the coupling between compartmentalization and biochemical reactions. We illustrate these concepts with selected examples, ranging from simple solutions of individual proteins to more complex mixtures of proteins and RNA, which represent synthetic models of biological membraneless organelles. Finally, we discuss how this technology may impact the bottom-up fabrication of synthetic artificial cells and for the development of synthetic protein materials in biotechnology.

Shear-induced aggregation of amyloid β (1-40) in a parallel plate geometry

Protein aggregation is induced by various environmental or external factors and associated with various neurodegenerative diseases. Among various external factors, shear stress is inevitable for both in vivo and in vitro applications of proteins. In this study, Aβ (1-40) peptide, a derivative of the amyloid precursor protein, was subjected to constant (300, 500, 700 s^-1) and varying (ramp) shear in a parallel plate geometry to explore the implications of shear in terms of macro (viscosity) and micro (secondary structure, morphology) characteristics. Aβ (1-40) solution followed a shear thickening flow behaviour with performance index value 'n' of 2.12. The fibrillation process resulting from the shear force was evaluated in terms of dissipation energy, which was found to exceed the free energy of unfolding. This resulted in the formation of β-sheet rich structures, which were confirmed by CD and FTIR analyses and enhanced Th-T fluorescence. The apparent rate of aggregation (k) was found to increase with the shear rate, and inversely related to the solution viscosity. The maximum k value was 0.21 ± 0.3 min^-1 at 700 s^-1. The molecular weights of aggregates were determined using gel filtration, which were proportionally related to the solution viscosity. The average molecular weights were estimated to be 70, 62 and 52 KDa for samples sheared at 300, 500 and 700 s^-1, respectively. The present study has deciphered the interplay of viscosity, a fluid property, with the aggregation process and its corresponding change in the secondary structures of the peptide. These findings provide useful insights for understanding various proteopathies under shear force.Communicated by Ramaswamy H. Sarma.

The uniqueness of flow in probing the aggregation behavior of clinically relevant antibodies

The development of therapeutic monoclonal antibodies (mAbs) can be hindered by their tendency to aggregate throughout their lifetime, which can illicit immunogenic responses and render mAb manufacturing unfeasible. Consequently, there is a need to identify mAbs with desirable thermodynamic stability, solubility, and lack of self-association. These behaviors are assessed using an array of in silico and in vitro assays, as no single assay can predict aggregation and developability. We have developed an extensional and shear flow device (EFD), which subjects proteins to defined hydrodynamic forces which mimic those experienced in bioprocessing. Here, we utilize the EFD to explore the aggregation propensity of 33 IgG1 mAbs, whose variable domains are derived from clinical antibodies. Using submilligram quantities of material per replicate, wide-ranging EFD-induced aggregation (9-81% protein in pellet) was observed for these mAbs, highlighting the EFD as a sensitive method to assess aggregation propensity. By comparing the EFD-induced aggregation data to those obtained previously from 12 other biophysical assays, we show that the EFD provides distinct information compared with current measures of adverse biophysical behavior. Assessing a candidate's liability to hydrodynamic force thus adds novel insight into the rational selection of developable mAbs that complements other assays.