Multifunctional Floating Titania-Coated Macro/Mesoporous Photocatalyst for Efficient Contaminant Removal

Establishing an affordable solar-floating Fe2O3@A1-xRx-TiO2 photo-Fenton catalytic system through the cyclic utilization of iron waste to de-pollute textile water contamination

This study focuses on developing a cost-effective Fe2O3 catalyst from oilfield iron waste to create a floating heterogeneous photo-Fenton system with anatase/rutile(A/R) TiO2 heterophase photocatalyst (cork-Fe2O3@A1-xRx-TiO2) for treating textile pollution in sunlight. Through controlling sol-gel (SG) microwave heating technique, the A/R ratio of A1-xRx-TiO2 crystal is tuned (A/R ratio = 1.13 and Eg = 3.02 eV) to improve adsorption-photocatalytic removal of anionic/cationic dyes with an apparent kinetic rate (kapp) of 0.0074 min-1 under UV-visible irradiation. The developed cork-Fe2O3@A53.1R46.8-TiO2 floated system also outperforms the classical photo-Fenton with Fe/H2O2 benchmark, showing a 2-fold enhancement in textile dye degradation (kapp = 0.216 min-1 and space-time yield (SY) of 1.7*10-4 mol/E.g at pH 5.65) with high stability over four reuse cycles. The formation of Fe2O3@A53.1R46.8-TiO2 Type-II heterojunction is confirmed by optical and electrochemical analyses, allowing the acceleration of direct electron transfer mechanism and oxidative degradation of dyes during photo-Fenton reaction. As a case study, the cork-Fe2O3@A53.1R46.8-TiO2 system demonstrates a high capability for efficient mineralization of textile pollution in a real effluent, achieving 82 ± 2% reduction in the total organic contents at an operational cost of 2.61 $/kg.m3 in sunlight. Thus, this research addresses challenges in conventional Fenton chemistry, iron waste recycling, and catalyst retention, offering new insights for sustainable treatment of textile effluents and environmental protection.

Floating photocatalysts as promising materials for environmental detoxification and energy production: A review

The oxygenation process of the catalyst surface, the incident-light harvesting capability, and facile recycling of utilized photocatalysts play key role in the outstanding photocatalytic performances. The typical existing photocatalysts in powder form have many drawbacks, such as difficult separation from the treated water, insufficient surface oxygenation, poor active surface area, low incident-light harvesting ability, and secondary pollution of the environment. A great number of scientific works introduced novel and fresh ideas related to designing floating photocatalytic systems by immobilizing highly active photocatalysts onto a floatable substrate. Thanks to direct contact with the illuminated light and oxygen molecules in the interface of water/air, the photocatalytic performance is maximized through production of more reactive species, employed in the photocatalytic reactions. Furthermore, facile recovering of the utilized photocatalysts for next processes avoids secondary pollution as well as diminishes the process's price. This review highlights the performance of developed floating photocatalysts for diverse applications. Furthermore, different floating substrates and possible mechanisms in floating photocatalysts are briefly mentioned. In addition, several emerging self-floating photocatalytic systems are taken attention and discussed. Specially, coupling photo-thermal and photocatalytic effects seems to be a good strategy for introducing a new class of floating photocatalyst to utilize the free, abundant, and green sunlight energy for the aims of water desalination and purification. Despite of a large number of attempts about the floating photocatalysts, there are still plenty of rooms for more in-depth research to be carried out for attaining the required characteristics of the large scale utilizations of these materials.

Critical review on modified floating photocatalysts for emerging contaminants removal from landscape water: problems, methods and mechanism

Due to the disorderly discharge in modern production and daily life of people, emerging contaminants(ECs) began to appear in landscape water, and have become a key public concern. Because of the unique characteristics of landscape water, it is difficult to efficiently remove ECs either by natural purification or by traditional large-scale sewage treatment facilities. The ideal purification method is to remove them while maintaining a beautiful environment. Possessing the feature of low-density, floating photocatalysts could harvest sufficient light on the surface of the water for photocatalytic degradation, which may be an important supplement for ECs treatment in landscape water. This paper gave a review related to floating photocatalysts and proposed an idea of combining floating photocatalysts to construct bionic photocatalytic materials for contaminative landscape water treatment. Six types of common floating substrates and corresponding applications for floating photocatalysts were concluded in this paper, and the main problem leading to the low efficiency of photocatalysts and three corresponding three improvement strategies were discussed. Besides, the modification mechanisms of photocatalysts were discussed thoroughly. On this basis, the engineering application prospects of bionic photocatalytic materials were proposed to remove ECs in landscape water.

Electrospun composite nanofibers as novel high-performance and visible-light photocatalysts for removal of environmental pollutants: A review

Environmental pollution caused by industries and human manipulations is coming a serious global challenge. On the other hand, the world is facing an energy crisis caused by population growth. Designing solar-driven photocatalysts which are inspired by the photosynthesis of plant leaves is a fantastic solution to use solar energy as green, available, and unlimited energy containing ∼50% visible light for the removal of environmental pollutants. The polymeric and non-polymeric-based electrospun composite nanofibers (NFs) are as innovative photocatalytic candidates which increase photocatalytic activity and transition from UV light to visible light and overcome the aggregation, photocorrosion, toxicity, and hard recycling and separation of the nanosized powder form of photocatalysts. The composite NFs are fabricated easily by either embedding the photocatalytic agents into the NFs during electrospinning or via their decorating on the surface of NFs post-electrospinning. Polyacrylonitrile-based, tungsten trioxide-based, zinc oxide-based, and titanium dioxide-based composite NFs were revealed as the most reported composite NFs. All the lately investigated electrospun composite NFs indicated long-term stability, high photocatalytic efficiency (∼> 80%) within a short time of light radiation (10-430 min), and high stability after several cycles of use. They were applied in various applications including degradation of dyes/antibiotics, water splitting, wastewater treatment, antibacterial usage, etc. The photogenerated species especially holes, O₂^∙-, and ^.OH were mostly responsible for the photocatalytic mechanism and pathway. The electrospun composite NFs have the potential to use in large-scale productions in condition that their thickness and recycling conditions are optimized, and their toxicity and detaching are resolved.

Renewable and eco-friendly ZnO immobilized onto dead sea sponge floating materials with dual practical aspects for enhanced photocatalysis and disinfection applications

In this study, we have investigated the role of natural dead sea sponge (DSS, Porifera) as a three-dimensional (3D) porous host substrate for the immobilization of nanostructured ZnO material towards the development of ZnO based floating photocatalysts for efficient removal of methylene blue (MB) dye under the illumination of sunlight. After photodegradation, the treated water after dye degradation contains several pathogens, different disinfectants or chemical reagents that are essentially used. This is not the case for DSS as it can naturally kill any pathogens during the wastewater treatment process. To explore these functions, ZnO nanosheets were incorporated onto DSS via hydrothermal protocol and the as prepared ZnO/DSS hybrid material exhibited approximately ∼100% degradation efficiency for the removal of MB. Importantly, the degradation kinetics associated with the fabricated ZnO/DSS was remarkably accelerated as evidenced by the high values of degradation reaction rate constants (3.35 × 10^-2min^-1). The outperformance of ZnO/DSS could be attributed to the adsorption caused by its 3D porous structure together with the high rapid oxidation of MB. Furthermore, the high charge separation of electron-hole pairs, natural porosity, and abundant catalytic sites offered by the hybrid ZnO/DSS floating photocatalyst have enabled quantitative (∼100%) degradation efficiency for MB. Finally, the excellent reusability results confirm the feasibility of using natural ZnO/DSS-based photocatalyst for practical solution of wastewater treatment and other environmental problems.

Effective Removal of Methylene Blue by Surface Alteration of TiO2 with Ficus Carica Leaf Extract under Visible Light

The present study describes the use of a leaf extract from Ficus carica as a source of natural antioxidants for the surface alteration of bulk titanium dioxide (TiO₂) in two steps. First, the hydro-thermal treatment of the bulk TiO₂ material was carried out and followed by thermal annealing at 300 °C for 3 h in air. The role of the leaf extract of Ficus carica on the performance of the bulk TiO₂ material for the removal of methylene blue (MB) was also studied. Various analytical techniques such as powder X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) were used to explore the crystalline structure, morphology, and composition. The bulk TiO₂ material after the leaf-extract treatment exhibited mixed anatase and rutile phases, a flower-like morphology, and Ti, O, and C were its main elements. The average crystallite size was also calculated, and the obtained values for the bulk TiO₂ material, 18.11 nm, and the treated bulk TiO₂ material with various amounts, 5, 10, and 15 mL, of leaf extract were 16.4, 13.16, and 10.29 nm respectively. Moreover, Fourier-transform infrared spectroscopy validated the typical metal-oxygen bonds and strengthened the XRD results. The bulk TiO₂ material chemically treated with Ficus carica has shown outstanding activity towards the degradation of MB under sunlight. The 15 mL of Ficus carica extract significantly enhanced the photocatalytic activity of the bulk TiO₂ material towards the degradation of MB. The dye degradation efficiency was found to be 98.8%, which was experimentally proven by the Fourier Transform Infrared spectroscopoyy (FTIR) analysis. The obtained performance of the bulk TiO₂ material with Ficus carica revealed excellent surface modifying properties for poorly-performing photocatalysts towards the degradation of synthetic dyes when used in their pristine form. The presented approach suggests that Ficus carica could be of great interest for tuning the surface properties of materials, either in the form of nano-size or bulk-phase in a particular application.

Comparison of the photoactivity of several semiconductor oxides in floating aerogel and suspension systems towards the reduction of Cr(VI) under visible light

A massive amount of research has been done over the last three decades to develop photoactive materials which could be suitable for real-world use in water remediation sector. Water-floating photocatalysts could be one of the best options due to their technological characteristics in terms of efficiency and reasonability including a high oxygenation of the photocatalyst surface, a fully sunlight irradiation, easy recovery and reuse. In the present study, aerogel water-floating based materials were fabricated using poly(vinyl alcohol) and polyvinylidene fluoride as a polymer platform, and loaded with different semiconductors such as g-C₃N₄, MoO₃, Bi₂O₃, Fe₂O₃ or WO₃. The photocatalytic efficiencies of aerogel floating materials and the suspension of above-mentioned semiconductors were compared evaluating the photoreduction of Cr(VI) under visible light (λ > 420 nm). The results showed that Fe₂O₃ suspension was the most efficient but the slowest in floating system. On the contrary, g-C₃N₄ exhibited a good performance in suspension system, and on top of that it was very effective in floating system, wherein it ensures a total reduction of 10 ppm-Cr(VI) to Cr(III) within 20 min.

TiO2/Ag2O immobilized on cellulose paper: A new floating system for enhanced photocatalytic and antibacterial activities

Paper-TiO₂-Ag₂O floating photocatalysts were produced under mild condition and their photocatalytic activity for the degradation of aromatic amine under sunlight stimulant was investigated. Characterizations by Raman, XRD, XPS, DRS and PL confirmed the presence of TiO₂ and Ag₂O, and the morphology of the appended TiO₂/Ag₂O layer was probed by FE-SEM. The photocatalytic activity of the prepared samples was investigated by the degradation of aniline (AN) in water under simulated sun-light illumination and constrained conditions, i.e. non-stirring and non-oxygenation. The presence of Ag₂O combined with TiO₂ was shown to improve the resistance of paper to bacteria attack, thus increasing the durability of the photocatalyst. Thanks to its hydrophobic character, the paper-TiO₂-Ag₂O NPs can be employed as useful floating photocatalyst and can be reused in continuous cycles.

Titanium Dioxide/Polyvinyl Alcohol/Cork Nanocomposite: A Floating Photocatalyst for the Degradation of Methylene Blue under Irradiation of a Visible Light Source

Photocatalytic degradation by the titanium dioxide (TiO2) photocatalyst attracts tremendous interest due to its promising strategy to eliminate pollutants from wastewater. The floating photocatalysts are explored as potential candidates for practical wastewater treatment applications that could overcome the drawbacks posed by the suspended TiO2 photocatalysis system. The problem occurs when the powdered TiO2 applied directly into the treated solution will form a slurry, making its reuse become a difficult step after treatment. In this study, the immobilization of titanium dioxide nanoparticles (TiO2 NPs) on the floating substrate (cork) employing polyvinyl alcohol (PVA) as a binder to anchor TiO2 NPs on the surface of the cork was carried out. Characterizations such as Fourier transformer infrared, X-ray diffraction (XRD), ultraviolet-visible spectroscopy (UV-vis), zeta potential, photoluminescence spectroscopy, femtosecond to millisecond time-resolved visible to mid-IR absorption spectroscopy, ion chromatography, and scanning electron microscopy-energy-dispersive X-ray spectroscopy (SEM-EDX) analyses were employed. XRD analysis revealed the formation of anatase-phase TiO2 NPs. The results demonstrated that the crystallite size was 9.36 nm. The band gap energy of TiO2 NPs was determined as 3.0 eV. PL analysis verified that TiO2 NPs possessed a slower recombination rate of electron-hole pairs as compared to anatase TiO2. The result was attributed by the behavior of photogenerated charge carriers on TiO2 NPs, which existed as shallowly trapped electrons that could survive longer than a few milliseconds in this study. Furthermore, SEM-EDX analysis indicated that TiO2 NPs were well distributed on the surface of the cork. At the optimal mole ratio of TiO2/PVA (1:8), the TiO2/PVA/cork floating photocatalyst degraded at 98.43% of methylene blue (MB) under a visible light source which performed better than under sunlight irradiation (77.09% of MB removal) for 120 min. Besides, the mineralization result has measured the presence of sulfate anions after photocatalytic activities, which achieved 86.13% (under a visible light source) and 65.34% (under sunlight). The superior photodegradation performance for MB was mainly controlled by the reactive oxygen species of the superoxide radical (•O2 -). The degradation kinetics of MB followed the first-order kinetics. Meanwhile, the Langmuir isotherm model was fitted for the adsorption isotherm. The floating photocatalyst presented good reusability, resulting in 78.13% of MB removal efficiency even after five cycles. Our TiO2/PVA/cork floating photocatalyst fabrication and high photocatalytic performance are potentially used in wastewater treatment, especially under visible light irradiation.

A Buoyant, Microstructured Polymer Substrate for Photocatalytic Degradation Applications

Microbubble fabrication of poly(dimethylsiloxane) (PDMS) beads with incorporated TiO2 provides a low-density, microstructured photocatalyst that is buoyant in water. This approach surmounts many of the challenges traditionally encountered in the generation of buoyant photocatalysts, an area which is critical for the implementation of widespread environmental cleaning of organic pollutants in water resources. Because the incorporation into the polymer bead surface is done at low temperatures, the crystal structure of TiO2 is unaltered, ensuring high-quality photocatalytic activity, while PDMS is well-established as biocompatible, temperature stable, and simple to produce. The photocatalyst is shown to degrade methylene blue faster than other buoyant, TiO2-based photocatalysts, and only an order of magnitude less than direct suspension of an equivalent amount of photocatalyst in solution, even though the photocatalyst is only present at the surface of the solution. The reusability of the TiO2/PDMS beads is also strong, showing no depreciation in photocatalytic activity after five consecutive degradation trials.

Visible-Light-Activated Black Organotitanias: How Synthetic Conditions Influence Their Structure and Photocatalytic Activity

A series of low-temperature, visible-light-activated black organotitanias were synthesised through a sol-gel strategy that allowed the in situ incorporation of p-phenylenediamine (PPD) into the framework of anatase nanoparticles. The effect of the synthetic conditions on the crystalline structure and photocatalytic activity of these materials was assessed by several characterisation techniques, which revealed a small crystalline domain size (4.6-5.5 nm), effective incorporation of PPD inside the nanoparticles, and a significant reduction in the band gap of these materials (from 3.2 to 2.7-2.9 eV). A systematic study of the synthetic parameters also allowed a significant reduction of the solvent used for the preparation of these black organotitanias (20-fold), as well as the crystallisation time, without compromising the structural properties and photocatalytic activity of these materials. The organotitanias with the highest PPD content and high crystallinity result in the best performing materials in the photocatalytic degradation of rhodamine 6G under both UV- and visible-light irradiation.

An easy preparation of photo-response TiO2@copper wire mesh with quick on/off switchable superwetting for high efficiency oil–water separation

A photo-response superwetting was easily fabricated using a hydrothermal method and titanium dioxide (TiO₂) on a copper wire mesh (CWM).

Ti3+ Self-Doped Blue TiO2(B) Single-Crystalline Nanorods for Efficient Solar-Driven Photocatalytic Performance

Ti³⁺ self-doped blue TiO₂(B) single-crystalline nanorods (b-TR) are fabricated via a simple sol-gelation method, cooperated with hydro-thermal treatment and subsequent in situ treatment method, and afterward annealed at 350 °C in Ar. The structures are characterized by X-ray diffraction (XRD), Raman, X-ray photoelectron spectroscopy (XPS), diffuse reflectance spectroscopy (UV-vis), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The prepared b-TR with narrow band gap possesses single-crystalline TiO₂(B) phase, Ti³⁺ self-doping, and one-dimensional (1D) rodlike nanostructure. In addition, the improved photocatalytic performance is studied by decomposition of Rhodamine B (RhB) and hydrogen evolution. The degradation rate of RhB by Ti³⁺ self-doped blue TiO₂(B) single-crystalline nanorods is ∼6.9- and 2.1-times higher compared with the rates of titanium dioxide nanoparticles and pristine TiO₂(B) nanorods under visible light illumination, respectively. The hydrogen evolution rate of b-TR is 26.6 times higher compared with that of titanium dioxide nanoparticles under AM 1.5 irradiation. The enhanced photocatalytic performances arise from the synergetic action of the special TiO₂(B) phase, Ti³⁺ self-doping, and the 1D rod-shaped single-crystalline nanostructure, favoring the visible light utilization and the separation and transportation of photogenerated charge carriers.

Fabrication of 3 D Mesoporous Black TiO2 /MoS2 /TiO2 Nanosheets for Visible-Light-Driven Photocatalysis

A novel 3 D mesoporous black TiO2 (MBT)/MoS2 /MBT sandwich-like nanosheet was successfully fabricated using a facile mechanochemical process combined with an in situ solid-state chemical reduction approach, followed by mild calcination (350 °C) under an argon atmosphere. The MBT/MoS2 /MBT exhibits a 3 D sandwich-like nanosheet structure and heterojunctions are formed at the interfaces between MoS2 and black TiO2 . The significantly narrowed band gap of MBT/MoS2 /MBT is attributed to the introduction of MoS2 and the formed Ti(3+) species in the frameworks. The visible-light photocatalytic degradation rate of methyl orange and the hydrogen production rate are as high as 89.86 % and 0.56 mmol h(-1)  g(-1) , respectively. The introduction of MoS2 and Ti(3+) in the frameworks favors the visible-light absorption and the separation of photogenerated charges, and the 3 D sandwich-like heterojunction structure facilitates the transfer of photogenerated charges.

Ni2+ and Ti3+ co-doped porous black anatase TiO2 with unprecedented-high visible-light-driven photocatalytic degradation performance

A black Ni doped porous TiO₂ were fabricated via an in situ solid-state chemical reduction approach, which exhibited excellent visible-light-driven performance.