Cell analysis system based on compact disk technology

The cytometric future: it ain't necessarily flow!

Initial approaches to cytometry for classifying and characterizing cells were based on microscopy; it was necessary to collect relatively high-resolution images of cells because only a few specific reagents usable for cell identification were available. Although flow cytometry, now the dominant cytometric technology, typically utilizes lenses similar to microscope lenses for light collection, improved, more quantitative reagents allow the necessary information to be acquired in the form of whole-cell measurements of the intensities of light transmission, scattering, and/or fluorescence.Much of the cost and complexity of both automated microscopes and flow cytometers arises from the necessity for them to measure one cell at a time. Recent developments in digital camera technology now offer an alternative in which one or more low-magnification, low-resolution images are made of a wide field containing many cells, using inexpensive light-emitting diodes (LEDs) for illumination. Minimalist widefield imaging cytometers can provide a smaller, less complex, and substantially less expensive alternative to flow cytometry, critical in systems intended for in resource-poor areas. Minimalism is, likewise, a good philosophy in developing instrumentation and methodology for both clinical and large-scale research use; it simplifies quality assurance and compliance with regulatory requirements, as well as reduces capital outlays, material costs, and personnel training requirements. Also, importantly, it yields "greener" technology.

Optically addressable single-use microfluidic valves by laser printer lithography

We report the design, fabrication, and characterization of practical microfluidic valves fabricated using laser printer lithography. These optofluidic valves are opened by directing optical energy from a solid-state laser, with similar power characteristics to those used in CD/DVD drives, to a spot of printed toner where localized heating melts an orifice in the polymer layer in as little as 500 ms, connecting previously isolated fluidic components or compartments. Valve functionality, response time, and laser input energy dependence of orifice size are reported for cyclo-olefin polymer (COP) and polyethylene terephthalate (PET) films. Implementation of these optofluidic valves is demonstrated on pressure-driven and centrifugal microfluidic platforms. In addition, these "one-shot" valves comprise a continuous polymer film that hermetically isolates on-chip fluid volumes within fluidic devices using low-vapor-permeability materials; we confirmed this for a period of one month. The fabrication and integration of optofluidic valves are compatible with a range of polymer microfabrication technologies and should facilitate the development of fully integrated, reconfigurable, and automated lab-on-a-chip systems, particularly when reagents must be stored on chip for extended periods, e.g. for medical diagnostic devices, lab-on-a-chip synthetic systems, or hazardous biochemical analysis platforms.

Personal cytometers: slow flow or no flow?

BACKGROUND

Although some manufacturers have optimistically described instruments with prices in the 40,000 US dollars range as "personal cytometers", analogy with the personal computer suggests that the target price for a true "personal" cytometer should be under 5,000 US dollars. Since such an apparatus could find a wide range of applications in cytomics in both developing and developed countries, it seemed desirable to consider its technical and economic feasibility.

METHODS

Using resolution targets and a variety of fluorescent bead standards immobilized on filters and/or slides, we evaluated high-intensity LEDs as fluorescence excitation sources, relatively inexpensive CCD cameras as detectors, and 35 mm camera lenses and plastic low-power microscope optics for light collection in a simple, inexpensive low-resolution imaging cytometer.

RESULTS

The components tested could be combined toproduce an instrument capable of detecting fewer than 10,000 molecules of cell-associated fluorescent label, and thus applicable to a broad range of cytometric tasks.

CONCLUSIONS

Given the requirements for light sources, detectors, optics, mechanics, electronics and data analysis hardware and software, and the components presently available, it should be easier to reach the desired 5,000 US dollars price point with an image cytometer than with a flow cytometer.

Geometry in digital molecular arrays

The development of digital molecular devices arises through the appropriate geometric positioning of a molecular assay. A detailed evaluation of the digital media reveals the critical aspects of geometric positioning in terms of developing an analytically-robust system for molecular analysis. This study reveals an explicit digital compact disc based assay for molecular affinity events.

Detection ofCryptosporidium parvum oocysts using a microfluidic device equipped with the SUS micromesh and FITC-labeled antibody

Development of a microfluidic device equipped with micromesh for detection of Cryptosporidium parvum oocyst was reported. A micromesh consisting of 10 x 10 cavities was microfabricated on the stainless steel plate by laser ablation. Each cavity size, approximately 2.7 microm in diameter, was adopted to capture a single C. parvum oocyst. Under negative pressure operation, suspensions containing microbeads or C. parvum oocysts flowed into the microchannel. Due to strong non-specific adsorption of microbeads onto the PDMS microchannel surface during sample injection, the surface was treated with air plasma, followed by treatment with 1% sodium dodecyl sulfate (SDS) solution. This process reduced the non-specific adsorption of microbeads on the microchannel to 10% or less in comparison to a non-treated microchannel. This microfluidic device equipped with the SUS micromesh was further applied for the capture of C. parvum oocysts. Trapped C. parvum oocysts were visualized by staining with FITC-labeled anti-C. parvum oocyst antibody on a micromesh and counted under fluoroscopic observation. The result obtained by our method was consistent with that obtained by direct immunofluorescence assay coupled with immunomagnetic separation (DFA-IMS) method, indicating that the SUS micromesh is useful for counting of C. parvum oocysts. The newly designed microfluidic device exploits a geometry that allowed for the entrapment of oocysts on the micromesh while providing the rapid introduction of a series of reagents and washes through the microfluidic structure. Our data indicate that this microfluidic device is useful for high-throughput counting of C. parvum oocysts from tap water sample.

Magnetic nanoparticle-antibody conjugates for the separation of Escherichia coli O157:H7 in ground beef

The immunomagnetic separation with magnetic nanoparticle-antibody conjugates (MNCs) was investigated and evaluated for the detection of Escherichia coli O157:H7 in ground beef samples. MNCs were prepared by immobilizing biotin-labeled polyclonal goat anti-E. coli antibodies onto streptavidin-coated magnetic nanoparticles. For bacterial separation, MNCs were mixed with inoculated ground beef samples, then nanoparticle-antibody-E. coli O157:H7 complexes were separated from food matrix with a magnet, washed, and surface plated for microbial enumeration. The capture efficiency was determined by plating cells bound to nanoparticles and unbound cells in the supernatant onto sorbitol MacConkey agar. Key parameters, including the amount of nanoparticles and immunoreaction time, were optimized with different concentrations of E. coli O157:H7 in phosphate-buffered saline. MNCs presented a minimum capture efficiency of 94% for E. coli O157:H7 ranging from 1.6 x 10(1) to 7.2 x 10(7) CFU/ml with an immunoreaction time of 15 min without any enrichment. Capture of E. coli O157:H7 by MNCs did not interfere with other bacteria, including Salmonella enteritidis, Citrobacter freundii, and Listeria monocytogenes. The capture efficiency values of MNCs increased from 69 to 94.5% as E. coli O157:H7 decreased from 3.4 x 10(7) to 8.0 x 10(0) CFU/ml in the ground beef samples prepared with minimal steps (without filtration and centrifugation). An enrichment of 6 h was done for 8.0 x 10(0) and 8.0 x 10(1) CFU/ml of E. coli O157:H7 in ground beef to increase the number of cells in the sample to a detectable level. The results also indicated that capture efficiencies of MNCs for E. coli O157:H7 with and without mechanical mixing during immunoreaction were not significantly different (P > 0.05). Compared with microbeads based immunomagnetic separation, the magnetic nanoparticles showed their advantages in terms of higher capture efficiency, no need for mechanical mixing, and minimal sample preparation.

?Cellular astronomy??A foreseeable future in cytometry

Advances in electro-optic technology within the past 2 years, notably the development of high-intensity light-emitting diodes and highly efficient charge-coupled device cameras, have made it feasible to produce small, simple, rugged, automated fluorescence image cytometers, with selling prices well below 10,000 US dollars, that can make measurements previously the exclusive domain of flow and scanning cytometers costing many times more. It should be feasible to apply the new cytometric technology in scientific and geographic areas for which a previous generation of instruments was too complex and too expensive, e.g., to problems of diagnosis and management of infectious diseases prevalent at critical levels in resource-poor areas, such as the human immunodeficiency virus, malaria, and tuberculosis.

Near-infrared dyes for six-color immunophenotyping by laser scanning cytometry

BACKGROUND

To adequately analyze the complexity of the immune system and reduce the required sample volume for immunophenotyping in general, more measurable colors for the discrimination of leukocyte subsets are necessary. Immunophenotyping by the laser scanning cytometer (LSC), a slide-based cytometric technology, combines cell detection based on multiple colors with their subsequent visualization without the need for physical cell sorting. In the present study, the filter setting of the LSC was adapted for the measurement of the far-red emitting dye cyanine 7 (Cy7), thereby increasing the number of measurable commercially available fluorochromes.

METHODS

The optical filters of the LSC were replaced-photomultiplier (PMT) 3/allophycocyanin (APC): 740-nm dichroic long pass, and 670-/55-nm bandpass; PMT 4/Cy7: 810-/90-nm bandpass. Peripheral blood leukocytes were stained directly by fluorochrome-labeled antibodies or by indirect staining. The tandem dyes of Cy7 (phycoerythrin [PE]-Cy7, APC-Cy7) and the fluorochromes fluorescein isothiocyanate (FITC), PE, PE-Cy5, and APC were tested alone and in different combinations.

RESULTS

With the new filter combination and tandem fluorochromes, Cy7 was measurable at 488-nm (argon laser) or 633-nm (helium-neon laser) excitation. Resolution was in the range of FITC for PE-Cy7 but approximately 30% lower for APC-Cy7; spillover into the respective donor fluorochrome channel for both tandem dyes was prominent. A six-color panel for leukocyte subtyping was designed.

CONCLUSIONS

With this adaptation, it is possible to measure the tandem conjugates PE-Cy7 and APC-Cy7. This new setup opens the way for six-color immunophenotyping by LSC.

Magnetic field design for selecting and aligning immunomagnetic labeled cells

BACKGROUND

Recently we introduced the CellTracks cell analysis system, in which samples are prepared based on a combination of immunomagnetic selection, separation, and alignment of cells along ferromagnetic lines. Here we describe the underlying magnetic principles and considerations made in the magnetic field design to achieve the best possible cell selection and alignment of magnetically labeled cells. Materials and Methods Computer simulations, in combination with experimental data, were used to optimize the design of the magnets and Ni lines to obtain the optimal magnetic configuration.

RESULTS

A homogeneous cell distribution on the upper surface of the sample chamber was obtained with a magnet where the pole faces were tilted towards each other. The spatial distribution of magnetically aligned objects in between the Ni lines was dependent on the ratio of the diameter of the aligned object and the line spacing, which was tested with magnetically and fluorescently labeled 6 microm polystyrene beads. The best result was obtained when the line spacing was equal to or smaller than the diameter of the aligned object.

CONCLUSIONS

The magnetic gradient of the designed permanent magnet extracts magnetically labeled cells from any cell suspension to a desired plane, providing a homogeneous cell distribution. In addition, it magnetizes ferro-magnetic Ni lines in this plane whose additional local gradient adds to the gradient of the permanent magnet. The resultant gradient aligns the magnetically labeled cells first brought to this plane. This combination makes it possible, in a single step, to extract and align cells on a surface from any cell suspension.