Fusion processing of itraconazole solid dispersions by kinetisol dispersing: a comparative study to hot melt extrusion

Minimization of Acid-Catalyzed Degradation in KinetiSol Processing through HPMCAS Neutralization

Hypromellose acetate succinate (HPMCAS) is an enteric polymer that has been successfully employed as a carrier in amorphous solid dispersions (ASDs). Deprotonation of succinic acid substituents at intestinal pH levels results in solubilization of the polymer. However, the acidic moieties responsible for favorable pH-dependent solubility can also result in incompatibilities between acid-sensitive drugs and HPMCAS. Solution-state conversion of the carboxylic acid substituents of enteric polymers into carboxylate salts to reduce acid-mediated drug degradation is a demonstrated effective strategy for generating ASDs in enteric polymers. This work aimed to extend the use of a pre-ionized enteric polymer to KinetiSol solvent-free processing to reduce acid- or base-mediated drug degradation during processing. Pre-ionization of HPMCAS was accomplished by reaction with a stoichiometric quantity of sodium carbonate (Na₂CO₃) delivered as a saturated aqueous solution. The resulting ionized polymer, HPMCAS-Na, was dried thoroughly before processing. Tetrabenazine (TBZ) was chosen as a model drug for its susceptibility to degradation via both acid- and base-catalyzed reaction mechanisms and for its tendency to form a single impurity by these mechanisms. The use of HPMCAS-Na in KinetiSol solid dispersions (KSDs) of TBZ resulted in a 6- to 8-fold reduction of the acid- and base-generated TBZ impurity compared with KSDs formulated with untreated HPMCAS.

Assessing the Interrelationship of Microstructure, Properties, Drug Release Performance, and Preparation Process for Amorphous Solid Dispersions Via Noninvasive Imaging Analytics and Material Characterization

PURPOSE

The purpose of this work is to evaluate the interrelationship of microstructure, properties, and dissolution performance for amorphous solid dispersions (ASDs) prepared using different methods.

METHODS

ASD of GDC-0810 (50% w/w) with HPMC-AS was prepared using methods of spray drying and co-precipitation via resonant acoustic mixing. Microstructure, particulate and bulk powder properties, and dissolution performance were characterized for GDC-0810 ASDs. In addition to application of typical physical characterization tools, we have applied X-Ray Microscopy (XRM) to assess the contribution of microstructure to the characteristics of ASDs and obtain additional quantification and understanding of the drug product intermediates and tablets.

RESULTS

Both methods of spray drying and co-precipitation produced single-phase ASDs. Distinct differences in microstructure, particle size distribution, specific surface area, bulk and tapped density, were observed between GDC-0810 spray dried dispersion (SDD) and co-precipitated amorphous dispersion (cPAD) materials. The cPAD powders prepared by the resonant acoustic mixing process demonstrated superior compactibility compared to the SDD, while the compressibility of the ASDs were comparable. Both SDD powder and tablets showed higher in vitro dissolution than those of cPAD powders. XRM calculated total solid external surface area (S_A) normalized by calculated total solid volume (S_V) shows a strong correlation with micro dissolution data.

CONCLUSION

Strong interrelationship of microstructure, physical properties, and dissolution performance was observed for GDC-0810 ASDs. XRM image-based analysis is a powerful tool to assess the contribution of microstructure to the characteristics of ASDs and provide mechanistic understanding of the interrelationship.

Melt Fusion Techniques for Solubility Enhancement: A Comparison of Hot Melt Extrusion and KinetiSol® Technologies

A successful candidate for oral drug delivery needs to possess adequate solubility and dissolution rate to elicit its therapeutic action. Extensive research is being carried out to enhance the solubility of poorly soluble drugs through a number of techniques involving polymeric and non-polymeric approaches. Non-polymeric approaches such as micronization and nanocrystals are successful in improving the apparent solubility of drugs, but the sustenance of solubility is not always possible. Amorphous solid dispersions (ASDs) lead to solubility enhancement as well as the maintenance of solubility with the assistance of polymers, thereby improving bioavailability. Spray drying, hot melt extrusion (HME), and KinetiSol® technologies are some of the techniques capable of manufacturing ASDs. Each of these techniques has its own advantages and disadvantages in terms of processing challenges and applicability in preparing ASDs. The latter two technologies are similar in being fusion and non-solvent techniques to improve solubility. This review compares both HME and KinetiSol® techniques regarding mechanism, equipment design, formulation, and process parameters involved and scalability.

Recent advances in the surfactant and controlled release polymer-based solid dispersion

The oral route is the most preferred delivery route for drug administration due to its advantages such as lower cost, improved patient compliance, no need for trained personnel and the drug reactions are generally less severe. The major problem with new molecules in the drug discovery pipeline is poor solubility and dissolution rate that ultimately results in low oral bioavailability. Numerous techniques are available for solubility and bioavailability (BA) enhancement, but out of all, solid dispersion (SD) is proven to be the most feasible due to the least issues in manufacturing, processing, storage, and transportation. In the past few years, SD had been extensively applied to reinforce the common issues of insoluble drugs. Currently, many hydrophobic and hydrophilic polymers are used to prepare either immediate release or controlled release SDs. Therefore, the biological behavior of the SDs is contingent upon the use of appropriate polymeric carriers and methods of preparation. The exploration of novel carriers and methodologies in SD technology leads to improved BA and therapeutic effectiveness. Moreover, the clinical applicability of SD-based formulations has been increased with the discovery of novel polymeric carriers. In this review, emphasis is laid down on the present status of recent generations of SDs (i.e., surfactant and controlled release polymer-based SD) and their application in modifying the physical properties of the drug and modulation of pharmacological response in different ailments.

Improved Bioavailability of Poorly Water-Soluble Drug by Targeting Increased Absorption through Solubility Enhancement and Precipitation Inhibition

Itraconazole (ITZ) is a class II drug according to the biopharmaceutical classification system. Its solubility is pH 3-dependent, and it is poorly water-soluble. Its pKa is 3.7, which makes it a weak base drug. The aim of this study was to prepare solid dispersion (SD) pellets to enhance the release of ITZ into the gastrointestinal environment using hot-melt extrusion (HME) technology and a pelletizer. The pellets were then filled into capsules and evaluated in vitro and in vivo. The ITZ changed from a crystalline state to an amorphous state during the HME process, as determined using DSC and PXRD. In addition, its release into the gastrointestinal tract was enhanced, as was the level of ITZ recrystallization, which was lower than the marketed drug (Sporanox^®), as assessed using an in vitro method. In the in vivo study that was carried out in rats, the AUC_0-48h of the commercial formulation, Sporanox^®, was 1073.9 ± 314.7 ng·h·mL^-1, and the bioavailability of the SD pellet (2969.7 ± 720.6 ng·h·mL^-1) was three-fold higher than that of Sporanox^® (*** p < 0.001). The results of the in vivo test in beagle dogs revealed that the AUC_0-24h of the SD-1 pellet (which was designed to enhance drug release into gastric fluids) was 3.37 ± 3.28 μg·h·mL^-1 and that of the SD-2 pellet (which was designed to enhance drug release in intestinal fluids) was 7.50 ± 4.50 μg·h·mL^-1. The AUC of the SD-2 pellet was 2.2 times higher than that of the SD-1 pellet. Based on pharmacokinetic data, ITZ would exist in a supersaturated state in the area of drug absorption. These results indicated that the absorption area is critical for improving the bioavailability of ITZ. Consequently, the bioavailability of ITZ could be improved by inhibiting precipitation in the absorption area.

Optimizing Solvent Selection and Processing Conditions to Generate High Bulk-Density, Co-Precipitated Amorphous Dispersions of Posaconazole

Co-precipitation is an emerging method to generate amorphous solid dispersions (ASDs), notable for its ability to enable the production of ASDs containing pharmaceuticals with thermal instability and limited solubility. As is true for spray drying and other unit operations to generate amorphous materials, changes in processing conditions during co-precipitation, such as solvent selection, can have a significant impact on the molecular and bulk powder properties of co-precipitated amorphous dispersions (cPAD). Using posaconazole as a model API, this work investigates how solvent selection can be leveraged to mitigate crystallization and maximize bulk density for precipitated amorphous dispersions. A precipitation process is developed to generate high-bulk-density amorphous dispersions. Insights from this system provide a mechanistic rationale to control the solid-state and bulk powder properties of amorphous dispersions.

Strategies for synthesis of 1,2,4-triazole-containing scaffolds using 3-amino-1,2,4-triazole

1,2,4-Triazole-containing scaffolds are unique heterocyclic compounds present in an array of pharmaceuticals and biologically important compounds used in the drug-discovery studies against cancer cells, microbes, and various types of disease in the human body. This review article summarizes the pharmacological significance of the 1,2,4-triazole-containing scaffolds and highlights the latest strategies for the synthesis of these privileged scaffolds using 3-amino-1,2,4-triazole. This review stimulates further research to find new and efficient methodologies for accessing new 1,2,4-triazole-containing scaffolds which would be very useful for the discover of new drug candidates.

Potential of solid dispersions to enhance solubility, bioavailability, and therapeutic efficacy of poorly water-soluble drugs: newer formulation techniques, current marketed scenario and patents

In the last few decades, solid dispersion (SD) technology had been studied as an approach to produce an amorphous carrier to enhance the solubility, dissolution rate, and bioavailability of poorly water-soluble drugs. The use of suitable carrier and methodology in the preparation of SDs play a significant role in the biological behavior of the SDs. SDs have been prepared using a variety of pharmaceutically acceptable polymers utilizing various novel technologies. In the recent years, much attention has been paid toward the use of novel carriers and methodologies in exploring novel types of SDs to enhance therapeutic efficacy and bioavailability. The use of novel carriers and methodologies would be very beneficial for formulation scientists to develop some SDs-based formulations for their commercial use and clinical applications. In the present review, current literature of novel methodologies for SD preparation to enhance the dissolution rate, solubility, therapeutic efficacy, and bioavailability of poorly water-soluble drugs has been summarized and analyzed. Further, the current status of SDs, patent status, and future prospects have also been discussed.

Overview of the Manufacturing Methods of Solid Dispersion Technology for Improving the Solubility of Poorly Water-Soluble Drugs and Application to Anticancer Drugs

Approximately 40% of new chemical entities (NCEs), including anticancer drugs, have been reported as poorly water-soluble compounds. Anticancer drugs are classified into biologic drugs (monoclonal antibodies) and small molecule drugs (nonbiologic anticancer drugs) based on effectiveness and safety profile. Biologic drugs are administered by intravenous (IV) injection due to their large molecular weight, while small molecule drugs are preferentially administered by gastrointestinal route. Even though IV injection is the fastest route of administration and ensures complete bioavailability, this route of administration causes patient inconvenience to visit a hospital for anticancer treatments. In addition, IV administration can cause several side effects such as severe hypersensitivity, myelosuppression, neutropenia, and neurotoxicity. Oral administration is the preferred route for drug delivery due to several advantages such as low cost, pain avoidance, and safety. The main problem of NCEs is a limited aqueous solubility, resulting in poor absorption and low bioavailability. Therefore, improving oral bioavailability of poorly water-soluble drugs is a great challenge in the development of pharmaceutical dosage forms. Several methods such as solid dispersion, complexation, lipid-based systems, micronization, nanonization, and co-crystals were developed to improve the solubility of hydrophobic drugs. Recently, solid dispersion is one of the most widely used and successful techniques in formulation development. This review mainly discusses classification, methods for preparation of solid dispersions, and use of solid dispersion for improving solubility of poorly soluble anticancer drugs.

Homogeneity of amorphous solid dispersions - an example with KinetiSol®

KinetiSol^® is a high-shear, fusion-based technology capable of producing stable amorphous solid dispersions (ASDs) without the assistance of solvent. KinetiSol^® has proven successful with multiple challenging BCS class II and IV drugs, where drug properties like thermal instability or lack of appreciable solubility in volatile solvents make hot melt extrusion or spray drying unfeasible. However, there is a necessity to characterize the ASDs like those made by the KinetiSol^® process, in order to better understand whether KinetiSol^® is capable of homogeneously dispersing drug throughout a carrier in a short (<40 s) processing time. Our study utilized the high melting point, BCS class II drug, meloxicam, in order to evaluate the degree of homogeneity of 1, 5, and 10% w/w KinetiSol^®-processed samples. Powder blend homogeneity and content uniformity were evaluated, and all samples demonstrated a meloxicam concentration % relative standard deviation of ≤2.0%. SEM/EDS was utilized to map elemental distribution of the processed samples, which confirmed KinetiSol^®-processed materials were homogeneous at a 25 µm² area. Utilizing Raman spectroscopy, we were able to verify the amorphous content of the processed samples. Finally, we utilized ssNMR ¹H spin-lattice relaxation measurement to evaluate the molecular miscibility of meloxicam with the polymer at 1% w/w drug load, for the first time, and determined the processed sample was highly miscible at ∼200 nm scale. In conclusion, we determined the KinetiSol^® process is capable of producing ASDs that are homogeneously and molecularly well-dispersed drug-in-polymer at drug concentrations as low as 1% w/w.

Development of Itraconazole Tablets Containing Viscous KinetiSol Solid Dispersions: In Vitro and In Vivo Analysis in Dogs

The formulation factors relevant to developing immediate and controlled release dosage forms containing poorly soluble drugs dispersed in amorphous systems are poorly understood. While the utility of amorphous solid dispersions is becoming apparent in the pharmaceutical marketplace, literature reports tend to concentrate on the development of solid dispersion particulates, which then must be formulated into a tablet. Amorphous solid dispersions of itraconazole in high molecular weight hydroxypropyl methylcellulose were prepared by KinetiSol® Dispersing and tablets were formulated to immediately disintegrate or control the release of itraconazole. Formulated tablets were evaluated by two non-sink dissolution methodologies and the dosage form properties that controlled the gelling tendency of the dispersion carrier, hydroxypropyl methylcellulose, were investigated. Selected formulations were evaluated in an exploratory beagle dog pharmacokinetic study; the results of which indicate potential for a prolonged absorption phase relative to the commercially extruded control.

Expanding the Application and Formulation Space of Amorphous Solid Dispersions with KinetiSol®: a Review

Due to the high number of poorly soluble drugs in the development pipeline, novel processes for delivery of these challenging molecules are increasingly in demand. One such emerging method is KinetiSol, which utilizes high shear to produce amorphous solid dispersions. The process has been shown to be amenable to difficult to process active pharmaceutical ingredients with high melting points, poor organic solubility, or sensitivity to heat degradation. Additionally, the process enables classes of polymers not conventionally processable due to their high molecular weight and/or poor organic solubility. Beyond these advantages, the KinetiSol process shows promise with other applications, such as the production of amorphous mucoadhesive dispersions for delivery of compounds that would also benefit from permeability enhancement.

Effects of the Preparation Process on the Properties of Amorphous Solid Dispersions

The use of amorphous solid dispersions to improve the bioavailability of active ingredients from the BCS II and IV classifications continues to gain interest in the pharmaceutical industry. Over the last decade, methods for generating amorphous solid dispersions have been well established in commercially available products and in the literature. However, the amorphous solid dispersions manufactured by different technologies differ in many aspects, primarily chemical stability, physical stability, and performance, both in vitro and in vivo. This review analyzes the impact of manufacturing methods on those properties of amorphous solid dispersions. For example, the chemical stability of drugs and polymers can be influenced by differences in the level of thermal exposure during fusion-based and solvent-based processes. The physical stability of amorphous content varies according to the thermal history, particle morphology, and nucleation process of amorphous solid dispersions produced by different methods. The in vitro and in vivo performance of amorphous formulations are also affected by differences in particle morphology and in the molecular interactions caused by the manufacturing method. Additionally, we describe the mechanism of manufacturing methods and the thermodynamic theories that relate to amorphous formulations.

Melt Extrusion for a High Melting Point Compound with Improved Solubility and Sustained Release

The objective of the current study was to develop an amorphous solid dispersion for a high melting point compound, griseofulvin (GRF), with an enhanced solubility and a controlled release pattern utilizing hot melt extrusion (HME) technology. Hypromellose acetate succinate (HPMCAS, Shin-Etsu AQOAT®, medium particle size) was explored as the polymeric carrier, while hypromellose (HPMC, Metolose® SR) was chosen as the release rate control agent. GRF presented an HPMCAS grade-dependent solubility: AS-HMP > AS-MMP > AS-LMP. At 10 wt.% loading, the release of GRF was prolonged to 6 h with the incorporation of 10% HPMC 90SH-100SR, while its solubility was enhanced up to sevenfold. Fourier transform infrared spectroscopy (FT-IR) identified the H-bonding between drug and polymers. Element analysis utilizing X-ray photoelectron spectroscopy (XPS) discovered that less GRF aggregated on the surface of binary powders compared with ternary powders containing HPMC, indicating the relatively poor wettability of the latter one. The morphology of extrudates was observed by scanning electron microscopy (SEM) and atomic force microscopy (AFM), illustrating a much smoother and uniform surface of binary extrudates. Immediate release tablets including 10% super-disintegrant L-HPC were able to achieve identical dissolution profile as the powders of extrudates.

Hot Melt Extrudates Formulated Using Design Space: One Simple Process for Both Palatability and Dissolution Rate Improvement

This work aimed at obtaining an optimized itraconazole (ITZ) solid oral formulation in terms of palatability and dissolution rate by combining different polymers using hot melt extrusion (HME), according to a simplex centroid mixture design. For this, the polymers Plasdone^® (poly(1-vinylpyrrolidone-co-vinyl acetate) [PVP/VA]), Klucel^® ELF (2-hydroxypropyl ether cellulose [HPC]), and Soluplus^® (SOL, polyvinyl caprolactam-polyvinyl acetate-polyethylene glycol) were processed using a laboratory HME equipment operating without recirculation at constant temperature. Samples were characterized by physicochemical assays, as well as dissolution rate and palatability using an e-tongue. All materials became homogeneous and dense after HME processing. Thermal and structural analyses demonstrated drug amorphization, whereas IR spectroscopy evidenced drug stability and drug-excipient interactions in HME systems. Extrudates presented a significant increase in dissolution rate compared to ITZ raw material, mainly with formulations containing PVP/VA and HPC. A pronounced improvement in taste masking was also identified for HME systems, especially in those containing higher amounts of SOL and HPC. Data showed polymers act synergistically favoring formulation functional properties. Predicted best formulation should contain ITZ 25.0%, SOL 33.2%, HPC 28.9%, and PVP/VA 12.9% (w/w). Optimized response considering dissolution rate and palatability reinforces the benefit of polymer combinations.

Processing thermally labile drugs by hot-melt extrusion: The lesson with gliclazide

The formation of molecularly dispersed amorphous solid dispersions by the hot-melt extrusion technique relies on the thermal and mechanical energy inputs, which can cause chemical degradation of drugs and polymeric carriers. Additionally, drug degradation may be exacerbated as drugs convert from a more stable crystalline form to a higher energy amorphous form. Therefore, it is imperative to study how drug degrades and evaluate methods to minimize drug degradation during the extrusion process. In this work, gliclazide was used as a model thermally labile drug for the degradation kinetics and process optimization studies. Preformulation studies were conducted using thermal analyses, and liquid chromatography-mass spectroscopy to identify drug degradation pathways and to determine initial extrusion conditions. Formulations containing 10% drug and 90% AFFINISOL™ HPMC HME 100LV were then extruded using a twin screw extruder, and the extrudates were characterized using X-ray powder diffraction, modulated dynamic scanning calorimetry, and potency testing to evaluate physicochemical properties. The energies of activation for both amorphous gliclazide, crystalline gliclazide, and gliclazide solution were calculated using the Arrhenius equation to further guide the extrusion optimization process. Preformulation studies identify two hydrolysis degradation pathways of gliclazide at elevated temperatures. The activation energy study indicates a significantly higher degradation rate for the amorphous gliclazide compared to the crystalline form. After optimization of the hot-melt extrusion process, including improved screw designs, machine setup, and processing conditions, gliclazide amorphous solid dispersion with ∼95% drug recovery was achieved. The ability to process thermally labile drugs and polymers using hot-melt extrusion will significantly expand the possible applications of this manufacturing process.

Thermal Processing of PVP- and HPMC-Based Amorphous Solid Dispersions

Thermal processing technologies continue to gain interest in pharmaceutical manufacturing. However, the types and grades of polymers that can be utilized in common thermal processing technologies, such as hot-melt extrusion (HME), are often limited by thermal or rheological factors. The objectives of the present study were to compare and contrast two thermal processing methods, HME and KinetiSol® Dispersing (KSD), and investigate the influence of polymer type, polymer molecular weight, and drug loading on the ability to produce amorphous solid dispersions (ASDs) containing the model compound griseofulvin (GRIS). Dispersions were analyzed by a variety of imaging, solid-state, thermal, and solution-state techniques. Dispersions were prepared by both HME and KSD using polyvinylpyrrolidone (PVP) K17 or hydroxypropyl methylcellulose (HPMC) E5. Dispersions were only prepared by KSD using higher molecular weight grades of HPMC and PVP, as these could not be extruded under the conditions selected. Powder X-ray diffraction (PXRD) analysis showed that dispersions prepared by HME were amorphous at 10% and 20% drug load; however, it showed significant crystallinity at 40% drug load. PXRD analysis of KSD samples showed all formulations and drug loads to be amorphous with the exception of trace crystallinity seen in PVP K17 and PVP K30 samples at 40% drug load. These results were further supported by other analytical techniques. KSD produced amorphous dispersions at higher drug loads than could be prepared by HME, as well as with higher molecular weight polymers that were not processable by HME, due to its higher rate of shear and torque output.

Miscibility of Itraconazole-Hydroxypropyl Methylcellulose Blends: Insights with High Resolution Analytical Methodologies

Drug-polymer miscibility is considered to be a prerequisite to achieve an optimally performing amorphous solid dispersion (ASD). Unfortunately, it can be challenging to evaluate drug-polymer miscibility experimentally. The aim of this study was to investigate the miscibility of ASDs of itraconazole (ITZ) and hydroxypropyl methylcellulose (HPMC) using a variety of analytical approaches. The phase behavior of ITZ-HPMC films prepared by solvent evaporation was studied before and after heating. Conventional methodology for miscibility determination, that is, differential scanning calorimetry (DSC), was used in conjunction with emerging analytical techniques, such as fluorescence spectroscopy, fluorescence imaging, and atomic force microscopy coupled with nanoscale infrared spectroscopy and nanothermal analysis (AFM-nanoIR-nanoTA). DSC results showed a single glass transition event for systems with 10% to 50% drug loading, suggesting that the ASDs were miscible, whereas phase separation was observed for all of the films based on the other techniques. The AFM-coupled techniques indicated that the phase separation occurred at the submicron scale. When the films were heated, it was observed that the ASD components underwent mixing. The results provide new insights into the phase behavior of itraconazole-HPMC dispersions and suggest that the emerging analytical techniques discussed herein are promising for the characterization of miscibility and microstructure in drug-polymer systems. The observed differences in the phase behavior in films prepared by solvent evaporation before and after heating also have implications for processing routes and suggest that spray drying/solvent evaporation and hot melt extrusion/melt mixing can result in ASDs with varying extent of miscibility between the drug and the polymer.

Solubility and dissolution enhancement strategies: current understanding and recent trends

Identification of lead compounds with higher molecular weight and lower aqueous solubility has become increasingly prevalent with the advent of high throughput screening. Poor aqueous solubility of these lipophilic compounds can drastically affect the dissolution rate and subsequently the drug absorbed in the systemic circulation, imposing a significant burden of time and money during drug development process. Various pre-formulation and formulation strategies have been applied in the past that can improve the aqueous solubility of lipophilic compounds by manipulating either the crystal lattice properties or the activity coefficient of a solute in solution or both, if possible. However, despite various strategies available in the armor of formulation scientist, solubility issue still remains an overriding problem in the drug development process. It is perhaps due to the insufficient conceptual understanding of solubility and dissolution phenomenon that hinders the judgment in selecting suitable strategy for improving aqueous solubility and/or dissolution rate. This article, therefore, focuses on (i) revisiting the theoretical and mathematical concepts associated with solubility and dissolution, (ii) their application in making rationale decision for selecting suitable pre-formulation and formulation strategies and (iii) the relevant research performed in this field in past decade.

Interactions between drugs and polymers influencing hot melt extrusion

Objectives

Hot melt extrusion (HME) as a technique for producing amorphous solid dispersion (ASD) has been widely used in pharmaceutical research. The biggest challenge for the application of HME is the thermal degradation of drug, poor physical stability of ASD and precipitation of drug during dissolution. Interactions between drugs and polymers may play an important role in overcoming these barriers. In this review, influence of drug–polymer interactions on HME and the methods for characterizing the drug–polymer interactions were reviewed.

Key findings

Strong drug–polymer interactions, especially ionic interactions and hydrogen bonds, are helpful to improving the thermal stability of drug during HME, enhancing the physical stability of ASD during storage and maintaining supersaturated solution after dissolution in gastrointestinal tract. The interactions can be quantitatively and qualitatively characterized by many analysing methods.

Conclusions

As many factors collectively determine the properties of HME products, drug–polymer interactions play an extremely important role. However, the action mechanisms of drug–polymer interactions need intensive investigation to provide more useful information for optimizing the formulation and the process parameters of HME.

Strategies to address low drug solubility in discovery and development

Drugs with low water solubility are predisposed to low and variable oral bioavailability and, therefore, to variability in clinical response. Despite significant efforts to "design in" acceptable developability properties (including aqueous solubility) during lead optimization, approximately 40% of currently marketed compounds and most current drug development candidates remain poorly water-soluble. The fact that so many drug candidates of this type are advanced into development and clinical assessment is testament to an increasingly sophisticated understanding of the approaches that can be taken to promote apparent solubility in the gastrointestinal tract and to support drug exposure after oral administration. Here we provide a detailed commentary on the major challenges to the progression of a poorly water-soluble lead or development candidate and review the approaches and strategies that can be taken to facilitate compound progression. In particular, we address the fundamental principles that underpin the use of strategies, including pH adjustment and salt-form selection, polymorphs, cocrystals, cosolvents, surfactants, cyclodextrins, particle size reduction, amorphous solid dispersions, and lipid-based formulations. In each case, the theoretical basis for utility is described along with a detailed review of recent advances in the field. The article provides an integrated and contemporary discussion of current approaches to solubility and dissolution enhancement but has been deliberately structured as a series of stand-alone sections to allow also directed access to a specific technology (e.g., solid dispersions, lipid-based formulations, or salt forms) where required.

Investigation into mixing capability and solid dispersion preparation using the DSM Xplore Pharma Micro Extruder

Objectives

The goal of this investigation was to qualify the DSM Xplore Pharma Micro Extruder as a formulation screening tool for early-stage hot-melt extrusion.

Methods

Dispersive and distributive mixing was investigated using soluplus, copovidone or basic butylated methacrylate copolymer with sodium chloride (NaCl) in a batch size of 5 g. Eleven types of solid dispersions were prepared using various drugs and carriers in batches of 5 g in accordance with the literature.

Key findings

The dispersive mixing was a function of screw speed and recirculation time and the particle size was remarkably reduced after 1 min of processing, regardless of the polymers. An inverse relationship between the particle size and specific mechanical energy (SME) was also found. The SME values were higher than those in large-scale extruders. After 1 min recirculation at 200 rpm, the uniformity of NaCl content met the criteria of the European Pharmacopoeia, indicating that distributive mixing was achieved in this time. For the solid dispersions preparations, the results from different scanning calorimetry, powder X-ray diffractometry and in-vitro dissolution tests confirmed that all solid-dispersion systems were successfully prepared.

Conclusions

These findings demonstrated that the extruder is a useful tool to screen solid-dispersion formulations and their material properties on a small scale.

Melt extrusion with poorly soluble drugs

Melt extrusion (ME) over recent years has found widespread application as a viable drug delivery option in the drug development process. ME applications include taste masking, solid-state stability enhancement, sustained drug release and solubility enhancement. While ME can result in amorphous or crystalline solid dispersions depending upon several factors, solubility enhancement applications are centered around generating amorphous dispersions, primarily because of the free energy benefits they offer. In line with the purview of the current issue, this review assesses the utility of ME as a means of enhancing solubility of poorly soluble drugs/chemicals. The review describes major processing aspects of ME technology, definition and understanding of the amorphous state, manufacturability, analytical characterization and biopharmaceutical performance testing to better understand the strength and weakness of this formulation strategy for poorly soluble drugs. In addition, this paper highlights the potential advantages of employing a fusion of techniques, including pharmaceutical co-crystals and spray drying/solvent evaporation, facilitating the design of formulations of API exhibiting specific physico-chemical characteristics. Finally, the review presents some successful case studies of commercialized ME based products.

Ditosylate salt of itraconazole and dissolution enhancement using cyclodextrins

Salt formation has been a promising approach for improving the solubility of poorly soluble acidic and basic drugs. The aim of the present study was to prepare the salt form of itraconazole (ITZ), a hydrophobic drug to improve the solubility and hence dissolution performance. Itraconazolium ditolenesulfonate salt (ITZDITOS) was synthesized from ITZ using acid addition reaction with p-toluenesulfonic acid. Salt characterization was performed using (1)H NMR, mass spectrometry, Fourier transform infrared spectroscopy, differential scanning calorimetry, and X-ray diffraction. The particle size and morphology was studied using dynamic light scattering technique and scanning electron microscopy, respectively. The solubility of the salt in water and various pharmaceutical solvents was found multifold than ITZ. The dissolution study exhibited 5.5-fold greater percentage release value in 3 h of ITZDITOS (44.53%) as compared with ITZ (8.54%). Results of in vitro antifungal studies using broth microdilution technique indicate that ITZDITOS possessed similar antifungal profile as that of ITZ when tested against four fungal pathogens. Furthermore, the physical mixtures of ITZDITOS with two cyclodextrins, β-cyclodextrin (β-CD), and 2-hydroxypropyl-β-cyclodextrin (HP-β-CD) were prepared in different molar ratios and were evaluated for in vitro release. It was observed that in only 30 min of dissolution study, about 74 and 81% of drug was released from 1:3 molar ratios of ITZDITOS with β-CD and ITZDITOS with HP-β-CD, respectively, which was distinctly higher than the drug released from ITZ commercial capsules (70%). The findings warrant further preclinical and clinical studies on ITZDITOS so that it can be established as an alternative to ITZ for developing oral formulations.

Preparation and characterization of fusion processed solid dispersions containing a viscous thermally labile polymeric carrier

The primary aim of the present study was to investigate the ability of hydroxypropyl and methoxyl substituted cellulose ethers to stabilize supersaturated concentrations of itraconazole (ITZ), a poorly water-soluble weak base, after an acid-to-neutral pH transition. A secondary aim of the study was to evaluate the effect of fusion processes on polymer stability and molecular weight. Polymer screening studies showed that stabilization of ITZ supersaturation was related to the molecular weight of the polymer and levels of hydroxypropyl and methoxyl substitution. METHOCEL E50LV (E50LV), which is characterized as having a high melt viscosity, was selected for solid dispersion formulation studies. Hot-melt extrusion processing of E50LV based compositions resulted in high torque loads, low material throughput and polymer degradation. KinetiSol Dispersing, a novel fusion based processing technique, was evaluated as a method to prepare the solid dispersions with reduced levels of polymer degradation. An experimental design revealed that polymer molecular weight was sensitive to shearing forces and high temperatures. However, optimal processing conditions resulted in significantly reduced E50LV degradation relative to HME processing. The technique was effectively utilized to prepare homogenous solid solutions of E50LV and ITZ, characterized as having a single glass transition temperature over a wide range of drug loadings. All prepared compositions provided for a high degree of ITZ supersaturation stabilization.

Hot-melt extrusion technology and pharmaceutical application

The use of hot-melt extrusion (HME) within the pharmaceutical industry is steadily increasing, due to its proven ability to efficiently manufacture novel products. The process has been utilized readily in the plastics industry for over a century and has been used to manufacture medical devices for several decades. The development of novel drugs with poor solubility and bioavailability brought the application of HME into the realm of drug-delivery systems. This has specifically been shown in the development of drug-delivery systems of both solid dosage forms and transdermal patches. HME involves the application of heat, pressure and agitation through an extrusion channel to mix materials together, and subsequently forcing them out through a die. Twin-screw extruders are most popular in solid dosage form development as it imparts both dispersive and distributive mixing. It blends materials while also imparting high shear to break-up particles and disperse them. HME extrusion has been shown to molecularly disperse poorly soluble drugs in a polymer carrier, increasing dissolution rates and bioavailability. The most common difficulty encountered in producing such dispersions is stabilization of amorphous drugs, which prevents them from recrystallization during storage. Pharmaceutical industrial suppliers, of both materials and equipment, have increased their development of equipment and chemicals for specific use with HME. Clearly, HME has been identified as an important and significant process to further enhance drug solubility and solid-dispersion production.

Dissolution enhancement of a drug exhibiting thermal and acidic decomposition characteristics by fusion processing: a comparative study of hot melt extrusion and KinetiSol dispersing

In this study, hot melt extrusion (HME) and KinetiSol Dispersing (KSD) were utilized to prepare dissolution-enhanced solid dispersions of Roche Research Compound A (ROA), a BCS class II drug. Preformulation characterization studies showed that ROA was chemically unstable at elevated temperatures and acidic pH values. Eudragit L100-55 and AQOAT LF (HPMCAS) were evaluated as carrier polymers. Dispersions were characterized for ROA recovery, crystallinity, homogeneity, and non-sink dissolution. Eudragit L100-55 dispersions prepared by HME required the use of micronized ROA and reduced residence times in order to become substantially amorphous. Compositions containing HPMCAS were also prepared by HME, but an amorphous dispersion could not be obtained. All HME compositions contained ROA-related impurities. KSD was investigated as a method to reduce the decomposition of ROA while rendering compositions amorphous. Substantially amorphous, plasticizer free compositions were processed successfully by KSD with significantly higher ROA recovery values and amorphous character than those achieved by HME. A near-infrared chemical imaging analysis was conducted on the solid dispersions as a measure of homogeneity. A statistical analysis showed similar levels of homogeneity in compositions containing Eudragit L100-55, while differences were observed in those containing HMPCAS. Non-sink dissolution analysis of all compositions showed rapid supersaturation after pH adjustment to approximately two to three times the equilibrium solubility of ROA, which was maintained for at least 24 h. The results of the study demonstrated that KSD is an effective method of forming dissolution-enhanced amorphous solid solutions in cases where HME is not a feasible technique.

Applications of KinetiSol dispersing for the production of plasticizer free amorphous solid dispersions

Thermal manufacturing methods for the production of solid dispersions frequently require the addition of a plasticizer in order to achieve requisite molten material flow properties when processed by unit operations such as hot melt extrusion. KinetiSol Dispersing, a rapid high energy thermal manufacturing process, was investigated for the ability to produce amorphous solid dispersions without the aid of a plasticizer. For this study itraconazole was used as a model active ingredient, while Eudragit L100-55 and Carbomer 974P were used as model solid dispersion carriers. Triethyl citrate (TEC) was used as necessary as a model plasticizer. Compositions prepared by KinetiSol Dispersing and hot melt extrusion were evaluated for solid state properties, supersaturated in vitro dissolution behavior under pH change conditions and accelerated stability performance. Results showed that both manufacturing processes were capable of producing amorphous solid dispersions, however compositions produced by hot melt extrusion required the presence of TEC and yielded a glass transition temperature (T(g)) of approximately 54 degrees C. Plasticized and unplasticized compositions were successfully produced by KinetiSol Dispersing, with plasticizer free solid dispersions exhibiting a T(g) of approximately 101 degrees C. Supersaturated in vitro dissolution testing revealed a significantly higher dissolution rate of plasticized material which was attributed to the pore forming behavior of TEC during the acidic phase of testing. A further contribution to release may also have been provided by the greater diffusivity in the plasticized polymer. X-ray diffraction testing revealed that under accelerated stability conditions, plasticized compositions exhibited partial recrystallization, while plasticizer free materials remained amorphous throughout the 6-month testing period. These results demonstrated that KinetiSol Dispersing could be used for the production of amorphous solid dispersions without the aid of a plasticizer and illustrated the enhanced solid state stability that can be achieved by producing solid dispersions with higher glass transition temperatures.