Sol/Gel Transition of Aqueous Alginate Solutions Induced by Fe2+ Cations

Plant extract mediated in-situ synthesis of iron/manganese alginate hydrosphere and its excellent recovery of rare earth elements in mine wastewater

The recovery of rare earth elements (REEs) is a major issue based on environmental governance and sustainable resource utilization. In this study, we developed a novel hydrogel material (Fe/Mn@ALG) by anchoring Fe/Mn NPs on alginate spheres, where Fe/Mn NPs were in-situ synthesized using Euphorbia cochinchensi leaf extract as reduced and protection agents. The Fe/Mn@ALG was applied directly to real mine wastewater, generating efficient and selective recovery of REEs with the coexistence of numerous competing metal ions. As results have shown, Fe/Mn@ALG was a useful adsorbent for REEs with an adsorption efficiency 78.62 % achieved, which was also confirmed by distribution coefficients (Kd), up to 2451.66 mL·g-1. Furthermore, Fe/Mn@ALG exhibited preferential response to REEs over other metal ions with the separation factor (SF) being up to 240. This great adsorption performance and selectivity toward REEs were attributed to its specific surface area, oxygen-rich functional groups and negatively charged surface in acid wastewater. Furthermore, REEs could be greatly desorbed from Fe/Mn@ALG with output concentration being three times higher than the initial concentration. Additionally, Fe/Mn@ALG maintained its good adsorption performance with efficiency reaching 72.24 % after five reuses. Overall, Fe/Mn@ALG can be considered as a promising candidate for wastewater remediation and sustainable management of resources.

Tuning the Properties of Xylan/Chitosan-Based Films by Temperature and Citric Acid Crosslinking Agent

Petroleum-based food packaging causes environmental problems such as waste accumulation and microplastic generation. In this work, biobased films from stable polyelectrolyte complex suspensions (PECs) of xylan and chitosan (70 Xyl/30 Ch wt% mass ratio), at different concentrations of citric acid (CA) (0, 2.5, 5, 7.5 wt%), were prepared and characterized. Films were treated at two temperatures (135 °C, 155 °C) and times (30 min, 60 min) to promote covalent crosslinking. Esterification and amidation reactions were confirmed by Fourier Transform Infrared Spectroscopy and Confocal Raman Microscopy. Water resistance and dry and wet stress-strain results were markedly increased by thermal treatment, mainly at 155 °C. The presence of 5 wt% CA tended to increase dry and wet stress-strain values further, up to 88 MPa-10% (155 °C for 60 min), and 5.6 MPa-40% (155 °C for 30 min), respectively. The UV-blocking performance of the films was improved by all treatments, as was thermal stability (up to Tonset: 230 °C). Contact angle values were between 73 and 84°, indicating partly wettable surfaces. Thus, thermal treatment at low CA concentrations represents a good alternative for improving the performance of Xyl/Ch films.

In-situ magnetic alginate coated chitosan core@shell beads with excellent performance in simulated and real wastewater treatment: Behavior, mechanisms, and new perspectives

Herein, a new hybrid magnetic core@shell biocomposite was prepared based on an alginate-bentonite core and a chitosan shell layer (mAB@Cs) where magnetic Fe3O4 NPs (50.7 nm) were in-situ generated on the surface via a simple non-thermal co-precipitation approach. The biocomposite has a high ability to magnetically separate and remove organic (ciprofloxacin (CPX)) and seven toxic inorganic (Cu2+, Cd2+, Co2+, Ni2+, Pb2+, Zn2+, and Hg2+) contaminants from simulated wastewater. Experimental results showed a CPX monolayer chemisorption with a Langmuir maximum adsorption capacity of 264.7 mg/g, maintained effectiveness up to the fifth cycle, and high removal rates of heavy metals ranging from 74.89 % to 99.86 % corresponding to adsorption capacities ranging from 12 to 20 mg/g. For a more accurate evaluation, the biocomposite was tested on a real urban wastewater sample (RWW) and it has manifested a noteworthy efficiency in removing a mixture of inorganic pollutants in terms of potassium K+ and orthophosphate phosphorous P-PO43-, and organic matter in terms of biological oxygen demand (BOD) and chemical oxygen demand (COD) with 46 %, 90 %, 84 %, and 64 % removal efficiencies, respectively. On top of this, a high inactivation rate of E. coli of the order of 96 % was recorded, making the prepared magnetic biocomposite adept for the simultaneous removal of emergent wastewater pollutants, from organic, inorganic, to pathogen microorganisms.

Property and Stability of Astaxanthin Emulsion Based on Pickering Emulsion Templating with Zein and Sodium Alginate as Stabilizer

Astaxanthin loaded Pickering emulsion with zein/sodium alginate (SA) as a stabilizer (named as APEs) was developed, and its structure and stability were characterized. The encapsulation efficiency of astaxanthin (Asta) in APEs was up to 86.7 ± 3.8%, with a mean particle size of 4.763 μm. Freeze-dried APEs showed particles stacked together under scanning electronic microscope; whereas dispersed spherical nanoparticles were observed in APEs dilution under transmission electron microscope images. Confocal laser scanning microscope images indicated that zein particles loaded with Asta were aggregated with SA coating. X-ray diffraction patterns and Fourier transform infrared spectra results showed that intermolecular hydrogen bonding, electrostatic attraction and hydrophobic effect were involved in APEs formation. APEs demonstrated non-Newtonian shear-thinning behavior and fit well to the Cross model. Compared to bare Asta extract, APEs maintained high Asta retention and antioxidant activity when heated from 50 to 10 °C. APEs showed different stability at pH (3.0-11.0) and Na+, K+, Ca2+, Cu2+ and Fe2+ conditions by visual, zeta potential and polydispersity index measurements. Additionally, the first order kinetics fit well to describe APEs degradation at pH 3.0 to 9.0, Na+, and K+ conditions. Our results suggest the potential application of Asta-loaded Pickering emulsion in food systems as a fortified additive.

Optimization of the Rheological Properties of Self-Assembled Tripeptide/Alginate/Cellulose Hydrogels for 3D Printing

3D printing is an emerging and powerful technique to create shape-defined three-dimensional structures for tissue engineering applications. Herein, different alginate-cellulose formulations were optimized to be used as printable inks. Alginate (Alg) was chosen as the main component of the scaffold due to its tunable mechanical properties, rapid gelation, and non-toxicity, whereas microcrystalline cellulose (MCC) was added to the hydrogel to modulate its mechanical properties for printing. Additionally, Fmoc-FFY (Fmoc: 9-fluorenylmethoxycarbonyl; F: phenylalanine; Y: tyrosine), a self-assembled peptide that promotes cell adhesion was incorporated into the ink without modifying its rheological properties and shear-thinning behavior. Then, 3D-printed scaffolds made of Alg, 40% of MCC inks and Fmoc-FFY peptide were characterized by scanning electron microscopy and infrared spectroscopy, confirming the morphological microstructure of the hydrogel scaffolds with edged particles of MCC homogeneously distributed within the alginate matrix and the self-assembly of the peptide in a β-sheet conformation. Finally, the cytocompatibility of the scaffolds was tested in contact with the MG63 osteosarcoma cells, confirming the absence of cytotoxic components that may compromise their viability. Interestingly, MG63 cell growth was retarded in the scaffolds containing the peptide, but cells were more likely to promote adhesive interactions with the material rather than with the other cells, indicating the benefits of the peptide in promoting biological functionality to alginate-based biomaterials.

A review of advances over 20 years on polysaccharide-based polymers applied as enhanced efficiency fertilizers

Over the last 20 years, polysaccharide-based materials have garnered attention in the enhanced efficiency fertilizers (EEFs) research. Biodegradability, non-toxicity, water-solubility, swellability, and ease of chemical modification make these polymers suitable for agricultural applications. In this review, the polysaccharides-based EEFs advances are summarized over the polymer and co-materials selection, the methods, and the chemical/structure aspects necessary for an appropriate production. We also briefly discuss terminologies, nutrient release mechanisms, biodegradation, and future trends. The most used polysaccharides are chitosan, starch, and alginate, and the non-Fickian model most describes the release mechanism. It is dependent on the relaxation of polymer chains by the matrix swelling followed by the nutrient diffusion. EEFs-polymers-based should be designed as more packed and less porous structures to avoid the immediate contact of the fertilizer with the surrounding water, improving fertilizer retention. Furthermore, the preparation methods will determine the scale-up of the material.

Dynamic cross-linking of an alginate-acrylamide tough hydrogel system: time-resolved in situ mapping of gel self-assembly

Hydrogels are a popular class of biomaterial that are used in a number of commercial applications (e.g.; contact lenses, drug delivery, and prophylactics). Alginate-based tough hydrogel systems, interpenetrated with acrylamide, reportedly form both ionic and covalent cross-links, giving rise to their remarkable mechanical properties. In this work, we explore the nature, onset and extent of such hybrid bonding interactions between the complementary networks in a model double-network alginate-acrylamide system, using a host of characterisation techniques (e.g.; FTIR, Raman, UV-vis, and fluorescence spectroscopies), in a time-resolved manner. Further, due to the similarity of bonding effects across many such complementary, interpenetrating hydrogel networks, the broad bonding interactions and mechanisms observed during gelation in this model system, are thought to be commonly replicated across alginate-based and broader double-network hydrogels, where both physical and chemical bonding effects are present. Analytical techniques followed real-time bond formation, environmental changes and re-organisational processes that occurred. Experiments broadly identified two phases of reaction; phase I where covalent interaction and physical entanglements predominate, and; phase II where ionic cross-linking effects are dominant. Contrary to past reports, ionic cross-linking occurred more favourably via mannuronate blocks of the alginate chain, initially. Evolution of such bonding interactions was also correlated with the developing tensile and compressive properties. These structure-property findings provide mechanistic insights and future synthetic intervention routes to manipulate the chemo-physico-mechanical properties of dynamically-forming tough hydrogel structures according to need (i.e.; durability, biocompatibility, adhesion, etc.), allowing expansion to a broader range of more physically and/or environmentally demanding biomaterials applications.

Ions-induced gelation of alginate: Mechanisms and applications

Alginate is an important natural biopolymer and has been widely used in the food, biomedical, and chemical industries. Ca²⁺-induced gelation is one of the most important functional properties of alginate. The gelation mechanism is well-known as egg-box model, which has been intensively studied in the last five decades. Alginate also forms gels with many other monovalent, divalent or trivalent cations, and their gelation can possess different mechanisms from that of Ca²⁺-induced gelation. The resulted gels also exhibit different properties that lead to various applications. This study is proposed to summarize the gelation mechanisms of alginate induced by different cations, mainly including H⁺, Ca²⁺, Ba²⁺, Cu²⁺, Sr²⁺, Zn²⁺, Fe²⁺, Mn²⁺, Al³⁺, and Fe³⁺. The mechanism of H⁺-induced gelation of alginate mainly depends on the protonation of carboxyl groups. Divalent ions-induced gelation of alginate show different selection towards G, M, and GM blocks. Trivalent ions can bind to carboxyl groups of uronates with no selection. The properties and applications of these ionotropic alginate gels are also discussed. The knowledge gained in this study would provide useful information for the practical applications of alginate.

Physical Properties, Chemical Analysis, and Evaluation of Antimicrobial Response of New Polylactide/Alginate/Copper Composite Materials

In recent years, due to an expansion of antibiotic-resistant microorganisms, there has been growing interest in biodegradable and antibacterial polymers that can be used in selected biomedical applications. The present work describes the synthesis of antimicrobial polylactide-copper alginate (PLA-ALG-Cu2+) composite fibers and their characterization. The composites were prepared by immersing PLA fibers in aqueous solution of sodium alginate, followed by ionic cross-linking of alginate chains within the polylactide fibers with Cu(II) ions to yield PLA-ALG-Cu2+ composite fibers. The composites, so prepared, were characterized by scanning electron microscopy (SEM), UV/VIS transmittance and attenuated total reflection Fourier-transform infrared spectroscopy ATR-FTIR, and by determination of their specific surface area (SSA), total/average pore volumes (through application of the 5-point Brunauer-Emmett-Teller method (BET)), and ability to block UV radiation (determination of the ultraviolet protection factor (UPF) of samples). The composites were also subjected to in vitro antimicrobial activity evaluation tests against colonies of Gram-negative (E. coli) and Gram-positive (S. aureus) bacteria and antifungal susceptibility tests against Aspergillus niger and Chaetomium globosum fungal mold species. All the results obtained in this work showed that the obtained composites were promising materials to be used as an antimicrobial wound dressing.

Photoresponsive Nanometer-Scale Iron Alginate Hydrogels: A Study of Gel-Sol Transition Using a Quartz Crystal Microbalance

Alginate/Fe³⁺ hydrogels were fabricated on hyaluronic acid (HA) and poly(allylamine hydrochloride) (PAH) multilayers to yield photoresponsive nanometer-scale hydrogels. Light irradiation of the resulting hydrogels induced the photoreduction of "hard" Fe³⁺ to "soft" Fe²⁺ cations, leading to changes in the mechanical properties of the hydrogels related to their cross-linking behavior. The buildup and the phototriggered response of the supported alginate hydrogels were followed in situ with a quartz crystal microbalance (QCM) using an open cell allowing light irradiation from an LED source on top of the hydrogel. The results were correlated to the release profiles of folic acid, employed herein as a drug model, obtained from light-irradiated supported iron alginate hydrogels.

Polysaccharide Coating of Gelatin Gels for Controlled BSA Release

Self-assembly of natural polymers constitute a powerful route for the development of functional materials. In particular, layer-by-layer (LBL) assembly constitutes a versatile technique for the nanostructuration of biobased polymers into multilayer films. Gelatin has gained much attention for its abundance, biodegradability, and excellent gel-forming properties. However, gelatin gels melt at low temperature, thus limiting its practical application. With respect to the above considerations, here, we explored the potential application of gelatin gels as a matrix for protein delivery at physiological temperature. A model protein, bovine serum albumin (BSA), was encapsulated within gelatin gels and then coated with a different number of bilayers of alginate and chitosan (10, 25, 50) in order to modify the diffusion barrier. The coated gel samples were analyzed by means of Attenuated Total Reflectance-Fourier Transform Infrared (ATR-FTIR) and confocal Raman spectroscopy, and it was found that the multilayer coatings onto polymer film were interpenetrated to some extent within the gelatin. The obtained results inferred that the coating of gelatin gels with polysaccharide multilayer film increased the thermal stability of gelatin gels and modulated the BSA release. Finally, the influence of a number of bilayers onto the drug release mechanism was determined. The Ritger-Peppas model was found to be the most accurate to describe the diffusion mechanism.

Local and controlled release of tamoxifen from multi (layer-by-layer) alginate/chitosan complex systems

Herein, multilayer polysaccharide films were proposed and characterized as biomaterials for the local and controlled release of an antitumoral drug. To that aim, multilayer films of alginate (Alg) and chitosan (Chi) were built up through spray assisted layer-by-layer (LbL) technique employing an automatic equipment. A specific drug against breast cancer, tamoxifen (TMX), was incorporated in different intermediate positions of the multilayer Alg/Chi films. Our findings highlight that Alg/Chi multilayer films can be employed for sustained and local TMX delivery and their therapeutic effect can be modulated and optimized by the number of bilayers deposited over the loaded tamoxifen, the quantity of tamoxifen loaded in several intermediate positions and the total area of the film.

Design of polygalacturonate hydrogels using iron(II) as cross-linkers: A promising route to protect bioavailable iron against oxidation

We designed stable and highly reproducible hydrogels by external unidirectional diffusion of Fe²⁺ ions into aqueous solutions of polygalacturonate (polyGal) chains. The Fe²⁺ ions act as cross-linkers between the Gal units in such a way that both the molar ratio R ([Fe²⁺]/[Gal units] = 0.25) and the mesh size of the polyGal network at the local scale (ξ = 75 ± 5 Å) have constant values within the whole gel, as respectively determined by titration and Small Angle Neutron Scattering. From macroscopic point of view, there is a progressive decrease of polyGal concentration from the part of the gel formed in the early stages of the gelation process, which is homogeneous, transparent and whose Young modulus has a high value of ∼10⁵ Pa, up to the part of the gel formed in the late stages, which is heterogeneous, highly turbid and has a much lower Young modulus of ∼10³ Pa. Since the local organization of the polyGal chains remains identical all along the hydrogels, this macroscopic concentration gradient originates from the formation of heterogeneities at a mesoscopic length scale during the gelation process. In addition, X-ray Absorption Spectroscopy measurements remarkably reveal that Fe²⁺ ions keep their +II oxidation state in the whole gels once they have cross-linked the Gal units. These polyGal hydrogels thus protect iron against oxidation and could be used for iron fortification.

Photodegradable iron(III) cross-linked alginate gels

Biocompatible photoresponsive materials are of interest for targeted drug delivery, tissue engineering, 2D and 3D protein patterning, and other biomedical applications. We prepared light degradable hydrogels using a natural alginate polysaccharide cross-linked with iron(III) cations. The "hard" iron(III) cations used to cross-link the alginate hydrogel were found to undergo facile photoreduction to "soft" iron(II) cations in the presence of millimolar concentrations of sodium lactate. The "soft" iron(II) cations have a decreased ability to cross-link the alginate which results in dissolution of the hydrogel and the formation of a homogeneous solution. The photodegradation is done using long wave UV or visible light at neutral pH. The very mild conditions required for the photodegradation and the high rate at which it occurs suggest applications for iron(III) cross-linked alginate hydrogels as light-controlled biocompatible scaffolds.