Chitosan-PEG hydrogel with sol-gel transition triggerable by multiple external stimuli

Rheological and Injectability Evaluation of Sterilized Poloxamer-407-Based Hydrogels Containing Docetaxel-Loaded Lipid Nanoparticles

Nanostructured lipid carriers (NLCs) have the potential to increase the bioavailability and reduce the side effects of docetaxel (DTX). However, only a small fraction of nanoparticles given intravenously can reach a solid tumor. In situ-forming gels combined with nanoparticles facilitate local administration and promote drug retention at the tumor site. Injectable hydrogels based on poloxamer 407 are excellent candidates for this hybrid nanoparticle-hydrogel system because of their thermoresponsive behavior and biocompatibility. Therefore, this work aimed to develop injectable poloxamer hydrogels containing NLCs for intratumoral delivery of DTX. To ensure sterility, the obtained hydrogels were autoclaved (121 °C for 15 min) after preparation. Then, the incorporation of NLCs into the poloxamer hydrogels and the impact of steam sterilization on the nanocomposite hydrogels were evaluated concerning sol-gel transition, injectability, and physicochemical stability. All formulations were extruded through the tested syringe-needle systems with acceptable force (2.2-13.4 N) and work (49.5-317.7 N·mm) of injection. Following steam sterilization, injection became easier in most cases, and the physicochemical properties of all hydrogels remained practically unchanged according to the spectroscopical and thermal analysis. The rheological evaluation revealed that the nanocomposite hydrogels were liquid at 25 °C and underwent rapid gelation at 37 °C. However, their sterilized counterparts gelled at 1-2 °C above body temperature, suggesting that the autoclaving conditions employed had rendered these nanocomposite hydrogels unsuitable for local drug delivery.

Injectable Chitosan-Methoxy Polyethylene Glycol Hybrid Hydrogel Untangling the Wound Healing Behavior: In Vitro and In Vivo Evaluation

Wound healing, particularly for difficult-to-treat wounds, presents a serious threat and may lead to complications. Currently available dressings lack mucoadhesion, safety, efficacy, and, most importantly, patient compliance. Herein, we developed a unique, simple, and inexpensive injectable chitosan-methoxy polyethylene glycol (chitosan-mPEG) hybrid hydrogel with tunable physicochemical and mechanical properties for wound healing. The detailed physicochemical and rheological characterization of the chitosan-mPEG hydrogel has revealed chemical interaction between available -NH2 groups of chitosan and -COOH groups of mPEG acid, which, to our perspective, enhanced the mechanical and wound healing properties of hybrid chitosan and mPEG hydrogel compared to solo chitosan or PEG hydrogel. By introducing mPEG, the wound healing ability of hydrogel is synergistically improved due to its antibacterial feature, together with chitosan's innate role in hemostasis and wound closure. The detailed hemostasis and wound closure potential of the chitosan-mPEG hydrogel were investigated in a rat model, which confirmed a significant acceleration in wound healing and ultimately wound closure. In conclusion, the developed chitosan-mPEG hydrogel met all the required specifications and could be developed as a promising material for hemostasis, especially wound management, and as an excellent candidate for wound healing application.

Cellulose-Based Ionic Conductor: An Emerging Material toward Sustainable Devices

Ionic conductors (ICs) find widespread applications across different fields, such as smart electronic, ionotronic, sensor, biomedical, and energy harvesting/storage devices, and largely determine the function and performance of these devices. In the pursuit of developing ICs required for better performing and sustainable devices, cellulose appears as an attractive and promising building block due to its high abundance, renewability, striking mechanical strength, and other functional features. In this review, we provide a comprehensive summary regarding ICs fabricated from cellulose and cellulose-derived materials in terms of fundamental structural features of cellulose, the materials design and fabrication techniques for engineering, main properties and characterization, and diverse applications. Next, the potential of cellulose-based ICs to relieve the increasing concern about electronic waste within the frame of circularity and environmental sustainability and the future directions to be explored for advancing this field are discussed. Overall, we hope this review can provide a comprehensive summary and unique perspectives on the design and application of advanced cellulose-based ICs and thereby encourage the utilization of cellulosic materials toward sustainable devices.

Three-Dimensional Bioprinting of Naturally Derived Hydrogels for the Production of Biomimetic Living Tissues: Benefits and Challenges

Three-dimensional bioprinting is the process of manipulating cell-laden bioinks to fabricate living structures. Three-dimensional bioprinting techniques have brought considerable innovation in biomedicine, especially in the field of tissue engineering, allowing the production of 3D organ and tissue models for in vivo transplantation purposes or for in-depth and precise in vitro analyses. Naturally derived hydrogels, especially those obtained from the decellularization of biological tissues, are promising bioinks for 3D printing purposes, as they present the best biocompatibility characteristics. Despite this, many natural hydrogels do not possess the necessary mechanical properties to allow a simple and immediate application in the 3D printing process. In this review, we focus on the bioactive and mechanical characteristics that natural hydrogels may possess to allow efficient production of organs and tissues for biomedical applications, emphasizing the reinforcement techniques to improve their biomechanical properties.

Significant Interfacial Dielectric Relaxation of Covalently Bonded Ice-Hydrogels

Hydrogels are composed of a three-dimensional network of cross-linked hydrophilic polymer chains and large amounts of water. The physicochemical properties of the polymer-water interface in hydrogels draw our attention. Due to the complex structure of hydrogel systems, it is still a challenge to investigate the interfacial layer properties of hydrogels through experiments. In this work, we investigate the properties of the covalently bonded chitosan-based ice-hydrogels interfacial layer by dielectric relaxation spectroscopy (DRS) techniques in the presence of avoided electrode polarization. The DRS data exhibit that the polymer-water interfacial layer has a strong dielectric signal response, which indicates that a large number of polar electric dipoles or polar molecules may be contained in the interfacial layer. The variable temperature dielectric relaxation behavior of a series of chitosan-base ice-hydrogels showed that the value of dielectric activation energy for different water contents is about 180 kJ/mol, which is much larger than that of the polymer and ice phases, suggesting a strong coupling of polar electric dipoles within the interfacial layer. This work demonstrates the important role of the polymer-water interface in covalently bonded hydrogels, which will provide assistance in the design and application of covalently bonded hydrogels.

Injectable Natural Polymer Hydrogels for Treatment of Knee Osteoarthritis

Osteoarthritis (OA) is a serious chronic and degenerative disease that increasingly occurs in the aged population. Its current clinical treatments are limited to symptom relief and cannot regenerate cartilage. Although a better understanding of OA pathophysiology has been facilitating the development of novel therapeutic regimen, delivery of therapeutics to target sites with minimal invasiveness, high retention, and minimal side effects remains a challenge. Biocompatible hydrogels have been recognized to be highly promising for controlled delivery and release of therapeutics and biologics for tissue repair. In this review, the current approaches and the challenges in OA treatment, and unique properties of injectable natural polymer hydrogels as delivery system to overcome the challenges are presented. The common methods for fabrication of injectable polysaccharide-based hydrogels and the effects of their composition and properties on the OA treatment are detailed. The strategies of the use of hydrogels for loading and release cargos are also covered. Finally, recent efforts on the development of injectable polysaccharide-based hydrogels for OA treatment are highlighted, and their current limitations are discussed.

The role of aldehyde-functionalized crosslinkers on the property of chitosan hydrogels

XXXX This article is protected by copyright. All rights reserved.

Deoxyribonucleic acid polymer nanoparticle hydrogels

Polymer nanoparticle hydrogels made of deoxyribonucleic acid and silica have been prepared and shown to display shear thinning and self-healing properties, sustained release of cargo and enzymatic degradation.

Development of a novel beta-glucan supplemented hydrogel spray formulation and wound healing efficacy in a db/db diabetic mouse model

To relief the severe economic and social burdens and patient suffering caused by the increasing incidence of chronic wounds, more effective treatments are urgently needed. In this study, we focused on developing a novel sprayable wound dressing with the active ingredient β-1,3/1,6-glucan (βG). Since βG is already available as the active ingredient in a commercial wound healing product provided as a hydrogel in a tube (βG-Gel), the sprayable format should bring clinical benefit by being easily sprayed onto wounds; whilst retaining βG-Gel's physical stability, biological safety and wound healing efficacy. Potentially sprayable βG hydrogels were therefore formulated, based on an experimental design setup. One spray formulation, named βG-Spray, was selected for further investigation, as it showed favorable rheological and spraying properties. The βG-Spray was furthermore found to be stable at room temperature for more than a year, retaining its rheological properties and sprayability. The cytotoxicity of βG-Spray in keratinocytes in vitro, was shown to be promising even at the highest tested concentration of 100 μg/ml. The βG-Spray also displayed favorable fluid affinity characteristics, with a capacity to both donate and absorb close to 10% fluid relative to its own weight. Finally, the βG-Spray was proven comparably effective to the commercial product, βG-Gel, and superior to both the water and the carrier controls (NoβG-Spray), in terms of its ability to promote wound healing in healing-impaired animals. Contraction was found to be the main wound closure mechanism responsible for the improvement seen in the βG-treatment groups (βG-Spray and βG-Gel). In conclusion, the novel sprayable βG formulation, confirmed its potential to expand the clinical use of βG as wound dressing.

Water-soluble poly(ethylene glycol) methyl ether-grafted chitosan/alginate polyelectrolyte complex hydrogels

This study aimed to fabricate polyelectrolyte complexes from water-soluble poly(ethylene glycol) methyl ether-grafted chitosan (mPEG-g-CTS) and alginate (ALG) in the absence of acetic acid. The complexes formed fibrous network macrogels when mPEG-g-CTS with short mPEG chains (mPEG750-g-CTS and mPEG2000-g-CTS) and mPEG-g-CTS:ALG weight ratios in the range from 1:0.14 to 1:1 were used. The macrogels at a weight ratio of mPEG-g-CTS:ALG of 1:1 possessed the highest elasticity with electrophoretic mobility close to 0 m²·V^-1·s^-1. Water uptake of the sponge-like lyophilized macrogels decreased with increasing ALG content, mPEG chain length, and degree of substitution of mPEG-g-CTS. In contrast, the polyelectrolyte complexes prepared using long mPEG chains of mPEG-g-CTS (mPEG5000-g-CTS) formed spherical nanoparticles (70-90 nm) and showed highly negative electrophoretic mobility (< -3.20 × 10⁸ m²·V^-1·s^-1). The obtained mPEG-g-CTS/ALG polyelectrolyte complex hydrogels and nanoparticles have the potential to be applied as carriers for functional food additives, drugs, and bioactive compounds.

Chitosan reinforced hydrogels with swelling-shrinking behaviors in response to glucose concentration

Different hydrogels of poly(acrylamide-co-3-acrylamido phenylboronic acid-co-chitosan grafted maleic acid) (P(AM-co-AAPBA-co-CSMA)s) were synthesized using poly(ethylene glycol) diacrylate (PEGDA) as a crosslinker to serve for glucose sensing and insulin delivery. The structure and morphology of the hydrogels, named as CSPBA were studied by FTIR and SEM, while the mechanical properties were tested using dynamic mechanical analysis (DMA) and universal testing machine. The prepared hydrogels shrinked at low glucose concentration due to the 2:1 boronate-glucose binding, and swelled at high glucose concentration because of 1:1 boronate-glucose complexation. Both binding mechanisms are useful for glucose sensing and insulin delivery. The integration of CSMA into hydrogels network not only enhanced the response to glucose at physiological pH, but also improved the mechanical properties and increased the encapsulation efficiency of the prepared hydrogels. These CSPBA may find potential as implantable hydrogels in applications were continuous glucose monitoring and controlled release is beneficial.

The fabrication of a highly efficient self-healing hydrogel from natural biopolymers loaded with exosomes for the synergistic promotion of severe wound healing

Unhealable diabetic wounds and disabling scar formation in severe wounds need to be addressed with the help of multiple techniques. Here we put forward an idea to use exosomes loaded into a supporting scaffold to rebuild the vascular transportation system, which could solve hypoxia and infertility in these wounds. A highly efficient self-healing and biocompatible natural-based methylcellulose-chitosan hydrogel loaded with biological exosome nanoparticles has the appropriate strength and is made by an easy preparation process, and it eventually achieves the integrated structure needed for healing severe diabetic conditions. Hydrogels perform well in the cell proliferation and skin remodeling stages because of their three-dimensional porous structure, and self-healing and adhesion properties. Also, exosomes accumulated to an effective concentration for a period of time could induce proliferation, especially relating to vascular formation. After the overpass (vascular) has been constructed with the help of the base (hydrogel) and workers (exosomes), the society (skin) is reconstructed under a system of supply and regulation. The research results indicate that these novel complex hydrogels loaded with exosomes provide wide prospects for the healing of severe wounds.

Crosslinked Chitosan-PEG Hydrogel for Culture of Human Glioblastoma Cell Spheroids and Drug Screening

Two-dimensional monolayer cell cultures are routinely utilized for preclinical cancer drug screening, but the results often do not translate well when drugs are tested in vivo. To address this limitation, a biocompatible chitosan-PEG hydrogel (CSPG gel) was synthesized to create a gel that can be easily dispensed into 96-well plates at room temperature and neutral pH. The stiffness of this gel was tailored to be within the stiffness range of human glioblastoma tissue to promote the formation of tumor spheroids. Differences in cell morphology, proliferation rate, and dose-dependent drug cytotoxicity were compared among cell spheroids grown on CSPG gels, cells in monolayer culture on tissue culture polystyrene and cells cultured on Matrigel. Tumor spheroids on CSPG gels displayed statistically significantly greater resistance to chemotherapeutics than in the conditions where cells did not form spheroids. Gene expression analysis suggests that resistance of cells on CSPG gels to the therapy may be partially attributed to upregulation of ATP-binding cassette transporters and downregulation of DNA mismatch repair genes, which was stimulated by spheroid formation. These findings suggest CSPG gel generates tumor spheroids that better reflect the malignant behavior of GBM and provides a cost-effective substrate for preclinical, high-throughput screening of potential cancer therapeutics.

Development and Evaluation of an Injectable Chitosan/β-Glycerophosphate Paste as a Local Antibiotic Delivery System for Trauma Care

Complex open musculoskeletal wounds are a leading cause of morbidity worldwide, partially due to a high risk of bacterial contamination. Local delivery systems may be used as adjunctive therapies to prevent infection, but they may be nondegradable, possess inadequate wound coverage, or migrate from the wound site. To address this issue, a thermo-responsive, injectable chitosan paste was fabricated by incorporating beta-glycerophosphate. The efficacy of thermo-paste as an adjunctive infection prevention tool was evaluated in terms of cytocompatibility, degradation, antibacterial, injectability, and inflammation properties. In vitro studies demonstrated thermo-paste may be loaded with amikacin and vancomycin and release inhibitory levels for at least 3 days. Further, approximately 60% of thermo-paste was enzymatically degraded within 7 days in vitro. The viability of cells exposed to thermo-paste exceeded ISO 10993-5 standards with approximately 73% relative viability of a control chitosan sponge. The ejection force of thermo-paste, approximately 20 N, was lower than previously studied paste formulations and within relevant clinical ejection force ranges. An in vivo murine biocompatibility study demonstrated that thermo-paste induced minimal inflammation after implantation for 7 days, similar to previously developed chitosan pastes. Results from these preliminary preclinical studies indicate that thermo-paste shows promise for further development as an antibiotic delivery system for infection prevention.

A smart safe rechargeable zinc ion battery based on sol-gel transition electrolytes

Thermal runaway has been a long-standing safety issue impeding the development of high-energy-density batteries. Physical safety designs such as employing circuit-breakers and fuses to batteries are limited by small operating voltage windows and no resumption of original working condition when it is cooled down. Here we report a smart thermoresponsive polymer electrolyte that can be incorporated inside batteries to prevent thermal runaway via a fast and reversible sol-gel transition, and successfully combine this smart electrolyte with a rechargeable Zn/α-MnO₂ battery system. At high temperature, battery operation is inhibited as a result of the increased internal resistance caused by the gelation of liquid electrolyte. After cooling down, the electrolyte is spontaneously reversed to sol state and the electrochemical performance of the battery is restored. More importantly, sol-gel transition enables the smart battery to experience different charge-discharge rates under various temperature levels, providing a smart and active strategy to achieve dynamic and reversible self-protection.

Preparation of injectable hydrogels from temperature and pH responsive grafted chitosan with tuned gelation temperature suitable for tumor acidic environment

In this present work, stimuli responsive polymers that can respond to the temperature and pH of the environment were prepared. A series of temperature responsive diblock copolymers based on poly(ethylene glycol) methyl ether (mPEG) and ε-caprolactone (CL) were synthesized. Subsequently, the diblock copolymers were grafted onto chitosan, a pH responsive biopolymer. These chitosan-graft-(mPEG-block-PCL) (chitosan-g-(mPEG-b-PCL)) graft copolymers were structurally characterized by ¹H NMR and FTIR and their sol-gel phase transitions were analyzed by the test tube inversion method as well as dynamic rheological measurements. These chitosan-g-(mPEG-b-PCL) graft copolymers demonstrated tunable temperature and pH responsive sol-gel phase transitions that correspond well with body temperature and pH of acidic tumor microenvironments. Gelation temperature (T_gel) decreased with increasing pH of the system, increasing PCL composition in the diblock copolymers, increasing solution concentration and decreasing grafting content of the diblock copolymers on chitosan. The graft copolymer hydrogels successfully showed the sustained release of both doxorubicin and curcumin for up to 2 weeks. The designed system was based on chitosan-g-(mPEG-b-PCL) graft copolymers, of which chitosan showed pH responsive properties and mPEG-b-PCL acted as a temperature sensitive moiety. In addition, mPEG and PCL are recognized as biocompatible polymers and chitosan has been engaged in various pharmaceutical research. Thus, this system could be considered an alternative choice for drug delivery applications.

The chitosan hydrogels: from structure to function

This review places an emphasis on chitosan intelligent hydrogels. The fabrication methods and mechanisms are introduced in this review and the interactions of the formation of hydrogels with both physical and chemical bonds are also introduced. The relationship between the structural characteristics and the corresponding functions of stimuli-responsive characteristics, self-healing functions and high mechanical strength properties of the chitosan hydrogels are discussed in detail.

Poly(ethylene glycol) and Cyclodextrin-Grafted Chitosan: From Methodologies to Preparation and Potential Biotechnological Applications

Chitosan, a polyaminosaccharide obtained by alkaline deacetylation of chitin, possesses useful properties including biodegradability, biocompatibility, low toxicity, and good miscibility with other polymers. It is extensively used in many applications in biology, medicine, agriculture, environmental protection, and the food and pharmaceutical industries. The amino and hydroxyl groups present in the chitosan backbone provide positions for modifications that are influenced by factors such as the molecular weight, viscosity, and type of chitosan, as well as the reaction conditions. The modification of chitosan by chemical methods is of interest because the basic chitosan skeleton is not modified and the process results in new or improved properties of the material. Among the chitosan derivatives, cyclodextrin-grafted chitosan and poly(ethylene glycol)-grafted chitosan are excellent candidates for a range of biomedical, environmental decontamination, and industrial purposes. This work discusses modifications including chitosan with attached cyclodextrin and poly(ethylene glycol), and the main applications of these chitosan derivatives in the biomedical field.

Blended Chitosan Paste for Infection Prevention: Preliminary and Preclinical Evaluations

BACKGROUND

Local drug delivery devices offer a promising method for delivering vancomycin and amikacin for musculoskeletal wounds. However, current local delivery devices such as beads and sponges do not necessarily allow for full coverage of a wound surface with eluted antibiotics and do not address the need for reducing the antibiotic diffusion distance to help prevent contamination by bacteria or other microorganisms. We blended chitosan/polyethylene glycol (PEG) pastes/sponges to increase biocompatibility and improve antibiotic coverage within the wound.

QUESTIONS/PURPOSES

(1) Are blended chitosan/PEG pastes biodegradable? (2) Are the blended pastes biocompatible? (3) How much force does paste require for placement by injection? (4) Will the pastes elute active antibiotics to inhibit bacteria in vitro? (5) Can the pastes prevent infection in a preclinical model with hardware?

METHODS

Our blended paste/sponge formulations (0.5% acidic, 1% acidic, and acidic/neutral) along with a control neutral 1% chitosan sponge were tested in vitro for degradability, cytocompatibility, injectability tested by determining the amount of force needed to inject the pastes, elution of antibiotics, and activity tested using zone of inhibition studies. Along with these studies, in vivo models for biocompatibility and infection prevention were tested using a rodent model and an infected mouse model with hardware, respectively. By evaluating these characteristics, an improved local drug delivery device can be determined.

RESULTS

All three of the paste formulations evaluated were almost fully degraded and with 6 days of degradation, the percent remaining being was less than that of the control sponge (percent remaining: control 99.251% ± 1.0%; 0.5% acidic 1.6% ± 2.1%, p = 0.002; 1% acidic 1.7% ± 1.6%, p = 0.002; acidic/neutral 2.3% ± 1.7%, p = 0.010). There was good biocompatibility because cell viability in vitro was high (control 100.0 ± 14.3; 0.5% acidic formulation at 79.4 ± 12.6, p < 0.001; 1% acidic formulation at 98.6 ± 6.1, p = 0.993; acidic/neutral formulation at 106.7 ± 12.8, p = 0.543), and in vivo inflammation was moderate (control 2.1 ± 1.2; 0.5% acidic 3.3 ± 0.2, p = 0.530; 1% acidic 2.5 ± 0.9, p = 0.657; acidic/neutral 2.9 ± 1.1, p = 0.784). Force required to inject the 0.5% acidic and 1% acidic pastes was less than the acidic/neutral paste used as a control (control 167.7 ± 85.6; 0.5% acidic 41.3 ± 10.7, p = 0.070; 1% acidic 28.0 ± 7.0, p = 0.940). At 72 hours, all paste formulations exhibited in vitro activity against Staphylococcus aureus (control 2.6 ± 0.8; 0.5% acidic 98.1 ± 33.5, p = 0.002; 1% acidic 87.3 ± 17.2, p = 0.006; acidic/neutral 83.5 ± 14.3, p = 0.010) and Pseudomonas aeruginosa (control 163.0 ± 1.7; 0.5% acidic 85.7 ± 83.6, p = 0.373; 1% acidic 38.0 ± 45.1, p = 0.896; acidic/neutral 129.7 ± 78.0, p = 0.896). Also, the paste formulations were able to prevent the infection with 100% clearance on the implanted hardware and surrounding tissue with the control being a 0.5% acidic paste group without antibiotics (control 4 × 10⁴ ± 4.8 × 10⁴; 0.5% acidic 0.0 ± 0.0, p value: 0.050; 1% acidic 0.0 ± 0.0, p = 0.050; acidic/neutral 0.0 ± 0.0, p = 0.050).

CONCLUSIONS

The preliminary studies demonstrated promising results for the blended chitosan/PEG pastes with antibiotics provided degradability, biocompatibility, injectability, and infection prevention for musculoskeletal-type wounds.

CLINICAL RELEVANCE

The preliminary studies with the chitosan paste delivered antibiotics to a contaminated musculoskeletal wound with hardware and prevented infection. More studies in a complex musculoskeletal wound and dosage studies are needed for continued development.

Evaluation of a chitosan-polyethylene glycol paste as a local antibiotic delivery device

AIM

To investigate the efficacy of a chitosan/polyethylene glycol blended paste as a local antibiotic delivery device, particularly in musculoskeletal wounds.

METHODS

Acidic (A) chitosan sponges and neutralized (N) chitosan/polyethylene glycol (PEG) blended sponges were combined in ratios of 3A:2N, 1A:1N, and 2A:3N; then hydrated with phosphate buffered saline to form a chitosan/PEG paste (CPP). Both in vitro and in vivo studies were conducted to determine the potential CPP has as a local antibiotic delivery device. In vitro biocompatibility was assessed by the cytotoxic response of fibroblast cells exposed to the experimental groups. Degradation rate was measured as the change in dry mass due to lysozyme based degradation over a 10-d period. The antibiotic elution profiles and eluate activity of CPP were evaluated over a 72-h period. To assess the in vivo antimicrobial efficacy of the CPP, antibiotic-loaded paste samples were exposed to subcutaneously implanted murine catheters inoculated with Staphylococcus aureus. Material properties of the experimental paste groups were evaluated by testing the ejection force from a syringe, as well as the adhesion to representative musculoskeletal tissue samples.

RESULTS

The highly acidic CPP group, 3A:2N, displayed significantly lower cell viability than the control sponge group. The equally distributed group, 1A:1N, and the highly neutral group, 2A:3N, displayed similar cell viability to the control sponge group and are deemed biocompatible. The degradation studies revealed CPP is more readily degradable than the chitosan sponge control group. The antibiotic activity studies indicated the CPP groups released antibiotics at a constant rate and remained above the minimum inhibitory concentrations of the respective test bacteria for a longer time period than the control chitosan sponges, as well as displaying a minimized burst release. The in vivo functional model resulted in complete bacterial infection prevention in all catheters treated with the antibiotic loaded CPP samples. All experimental paste groups exhibited injectability and adhesive qualities that could be advantageous material properties for drug delivery to musculoskeletal injuries.

CONCLUSION

CPP is an injectable, bioadhesive, biodegradable, and biocompatible material with potential to allow variable antibiotic loading and active, local antibiotic release to prevent bacterial contamination.

Synthesis of an injectable, self-healable and dual responsive hydrogel for drug delivery and 3D cell cultivation

An injectable, self-healable and dual pH and temperature responsive hydrogel was facilely prepared and applied as a potential carrier for drug delivery and cell cultivation.

Injectable Pore-Forming Hydrogel Scaffolds for Complex Wound Tissue Engineering: Designing and Controlling Their Porosity and Mechanical Properties

Traumatic soft tissue wounds present a significant reconstructive challenge. The adoption of closed-circuit negative pressure wound therapy (NPWT) has enabled surgeons to temporize these wounds before reconstruction. Such systems use porous synthetic foam scaffolds as wound fillers at the interface between the negative pressure system and the wound bed. The idea of using a bespoke porous biomaterial that enhances wound healing, as filler for an NPWT system, is attractive as it circumvents concerns regarding reconstructive delay and the need for dressing changes that are features of the current systems. Porous foam biomaterials are mechanically robust and able to synthesize in situ. Hence, they exhibit potential to fulfill the niche for such a functionalized injectable material. Injectable scaffolds are currently in use for minimally invasive surgery, but the design parameters for large-volume expansive foams remain unclear. Potential platforms include hydrogel systems, (particularly superabsorbent, superporous, and nanocomposite systems), polyurethane-based moisture-cured foams, and high internal phase emulsion polymer systems. The aim of this review is to discuss the design parameters for such future biomaterials and review potential candidate materials for further research into this up and coming field.

Modification of Thermal and Mechanical Properties of PEG-PPG-PEG Copolymer (F127) with MA-POSS

Pluronic F127 exhibits thermogelling behaviour at 20⁻30 °C via a micelle packing mechanism. Disruption of the micelle packing increases the sol-gel temperature, but results in the decrease of modulus. Herein, we reported a method to modify F127 with polyhedral oligosilsesquioxane (POSS) to impart a higher gelling temperature without yielding the property and strength of the thermogel. The thermal degradation temperature was enhanced to 15 °C after POSS incorporation and the gelling temperature shifted 10 °C higher, without sacrificing the modulus of the gel. Rheological studies supported the claim that the gel property was reinforced after POSS incorporation. F127-POSS copolymer matrix stored more energy from POSS reinforcement, which saw larger Lissajous curve areas before the collapse of the microstructure for the same amount of stress applied. These results indicated that modification with POSS would raise the sol-gel transition temperature without sacrificing the modulus of the gel.

PEG-chitosan hydrogel with tunable stiffness for study of drug response of breast cancer cells

Mechanical properties of the extracellular matrix have a profound effect on the behavior of anchorage-dependent cells. However, the mechanisms that define the effects of matrix stiffness on cell behavior remains unclear. Therefore, the development and fabrication of synthetic matrices with well-defined stiffness is invaluable for studying the interactions of cells with their biophysical microenvironment in vitro. We demonstrate a methoxypolyethylene glycol (mPEG)-modified chitosan hydrogel network where hydrogel stiffness can be easily modulated under physiological conditions by adjusting the degree of mPEG grafting onto chitosan (PEGylation). We show that the storage modulus of the hydrogel increases as PEGylation decreases and the gels exhibit instant self-recovery after deformation. Breast cancer cells cultured on the stiffest hydrogels adopt a more malignant phenotype with increased resistance to doxorubicin as compared with cells cultured on tissue culture polystyrene or Matrigel. This work demonstrates the utility of mPEG-modified chitosan hydrogel, with tunable mechanical properties, as an improved replacement of conventional culture system for in vitro characterization of breast cancer cell phenotype and evaluation of cancer therapies.

Mussel-Inspired Photografting on Colloidal Spheres: A Generalized Self-Template Route to Stimuli-Responsive Hollow Spheres for Controlled Pesticide Release

A thermo-controlled pesticide release system composed of poly(2-(dimethylamino)ethyl methacrylate) (PDMAEMA) thin film grafted polydopamine (PDA) (PDMAEMA-g-PDA) microcapsules is reported. SiO2 microparticles are used as a template to prepare PDA-coated SiO2 microparticles. The thermally-responsive PDMAEMA thin films are grafted on PDA surfaces using a metal-free surface-initiated photopolymerization approach without adding any photo-initiator or photosensitizer under UV light irradiation. The subsequent acid etching yields PDMAEMA-g-PDA hollow microcapsules. PDMAEMA-g-PDA microcapsules exhibit well-controlled release of avermectin (Av). The results show that the loading ability of PDMAEMA-g-PDA microcapsules of Av is up to 52.7% (w/w). The release kinetics of Av demonstrate that Av@PDMAEMA-g-PDA microcapsules exhibit temperature-controlled release performance. This work is significant for controlled release systems. This simple design is expected to be used in various applications, such as in controlled drug release and agriculture-related fields.