Physical and mechanical properties of graphene oxide/polyethersulfone nanocomposites

Highly Permeable Ultrafiltration Membranes Based on Polyphenylene Sulfone with Cardo Fragments

For the first time, copolymers of polyphenylene sulfone (PPSU) with cardo fragments of phenolphthalein (PP) were synthesized to develop highly permeable flat-sheet ultrafiltration membranes. By introducing cardo fragments into the polymer chain, we achieved a mechanical strength 1.3 times higher than the strength of commercial PPSU. It is shown that the introduction of the cardo monomer significantly increases the solubility of the polymer in aprotic solvents. The highest solubility is observed at the concentration of PP 50 mol.%. It is found that reduced viscosity of cardo polymer solutions leads to an increase in the coagulation rate. The permeance of asymmetric ultrafiltration membranes increases with PP concentration from 17.5 L/(m2·h·bar) (10 mol.% PP) to 85.2 L/(m2·h·bar) (90 mol.% PP). These data are in agreement with the results of a study of the coagulation rate of polymer solutions. Thus, for ultrafiltration membranes with 1.5-8 times higher permeance in comparison with PPSU due to the introduction of cardo fragments in the polymer chain, possessing high rejection of the model dye Blue Dextran (MW = 70,000 g/mol), more than 99.2%, as well as high strength characteristics, were achieved.

Preparation and Characterization of Low CTE Poly(ethersulfone) Using Lignin Nano Composites as Flexible Substrates

Polyethersulfone (PES) has outstanding thermal and dimensional stability. It is considered an engineering thermoplastic. However, its high coefficient of thermal expansion (CTE) hinders its use in automobiles, microelectronics, and flexible display areas. To overcome its high coefficient of thermal expansion (CTE), recent studies have focused on reducing its high CTE and improving its mechanical properties by adding nano-sized fillers or materials. The addition of nanofiller or nanofibrils to the PES matrix often has a positive effect on its mechanical and thermal properties, making it a flexible display substrate. To obtain ideal flexible substrates, we prepared polyethersulfone with lignin nanocomposite films to reduce CTE and improve the mechanical and thermal properties of PES by varying the relative ratio of PES in the lignin nanocomposite. In this study, lignin as a biodegradable nanofiller was found to show high thermal, oxidative, and hydrolytic stability with favorable mechanical properties. PES/lignin nanocomposite films were prepared by solution casting according to the content of lignin (0 to 5 wt.%). PES/lignin composite films were subjected to mechanical, thermo-mechanical, optical, and surface analyses. The results showed enhanced thermomechanical and optical properties of PES, with the potential benefits of lignin filler materials realized for the development of thermoplastic polymer blends.

Super-Tough and Biodegradable Poly(lactide-co-glycolide) (PLGA) Transparent Thin Films Toughened by Star-Shaped PCL-b-PDLA Plasticizers

To obtain fully degradable and super-tough poly(lactide-co-glycolide) (PLGA) blends, biodegradable star-shaped PCL-b-PDLA plasticizers were synthesized using natural originated xylitol as initiator. These plasticizers were blended with PLGA to prepare transparent thin films. Effects of added star-shaped PCL-b-PDLA plasticizers on mechanical, morphological, and thermodynamic properties of PLGA/star-shaped PCL-b-PDLA blends were investigated. The stereocomplexation strong cross-linked network between PLLA segment and PDLA segment effectively enhanced interfacial adhesion between star-shaped PCL-b-PDLA plasticizers and PLGA matrix. With only 0.5 wt% addition of star-shaped PCL-b-PDLA (Mn = 5000 g/mol), elongation at break of the PLGA blend reached approximately 248%, without any considerable sacrifice over excellent mechanical strength and modulus of PLGA.

High electromagnetic interference shielding of poly(ether-sulfone)/multi-walled carbon nanotube nanocomposites fabricated by an eco-friendly route

High-performance polymer matrix nanocomposites based on poly(ether-sulfone) (PES) matrix reinforced with multi-walled carbon nanotubes (MWCNTs) were fabricated using planetary ball mill followed by hot pressing. Their electrical properties and the electromagnetic interference shielding effectiveness (EMI-SE) were investigated and discussed. A percolation threshold of about 0.65 vol% MWCNT was obtained. The electrical conductivity was increased by more than ten orders of magnitude at the percolation threshold and to approximately 0.01 S cm^-1 at 6.67 vol% (or 10 wt%) MWCNT. This is a significant improvement. The highest EMI-SE of about 29-30 dB (both in the X-band and K_u-band) was obtained for the 6.67 vol% MWCNT filled nanocomposites with a thickness of 0.9 mm. The specific EMI-SE of these nanocomposites were found to be higher than the literature values. The thermal stability and the char yield (measured at 900 °C) of the nanocomposites were found to be more than 470 °C and 40.6%, respectively.

Experimental, Numerical, and Analytical Study on The Effect of Graphene Oxide in The Mechanical Properties of a Solvent-Free Reinforced Epoxy Resin

This paper presents a methodology for manufacturing nanocomposites from an epoxy resin reinforced with graphene oxide (GO) nanoparticles. A scalable and sustainable fabrication process, based on a solvent-free method, is proposed with the objective of achieving a high level of GO dispersion, while maintaining matrix performance. The results of three-point bending tests are examined by means of an analytical technique which allows determining the mechanical response of the material under tension and compression from flexural data. As result, an increase of 39% in the compressive elastic modulus of the nanocomposite is found with the addition of 0.3 wt % GO. In parallel, we described how the strain distribution and the failure modes vary with the amount of reinforcement based on digital image correlation (DIC) techniques and scanning electron microscopy (SEM). A novel analytical model, capable of predicting the influence of GO content on the elastic properties of the material, is obtained. Numerical simulations considering the experimental conditions are carried out. the full strain field given by the DIC system is successfully reproduced by means of the finite element method (FEM). While, the experimental failure is explained by the crack growth simulations using the eXtended finite element method (XFEM).

Synthesis of Structurally Precise Polysiloxanes via the Piers⁻Rubinsztajn Reaction

Silicone materials are widely used, from daily life to the military industry. With the advancement of science and technology and the increasing demands of industry, the requirement for high-performance precise structural silicone materials has increased. Therefore, the most important aspect in this field is finding a breakthrough in the synthetic methods. In this review, the latest research developments in controllable morphological structure and composite structure optimized synthesis of silicone materials using the Piers⁻Rubinsztajn (PR) reaction are summarized. The advantages of the PR reaction compared with traditional synthetic routes to silicone materials are presented. The highly controllable spatial structure of silicone materials and the structural combination of biomass or inorganic materials with silicone materials results in an improvement in performance or function. The morphological control of more complex silicone materials and the synthesis of non-traditional silicone materials with composite structures through the PR reaction will be the main research directions for the development of silicone materials in the future.

Oxidative Layer-By-Layer Multilayers Based on Metal Coordination: Influence of Intervening Graphene Oxide Layers

Layer-by-layer (LbL) fabricated oxidative multilayers consisting of successive layers of inorganic polyphosphate (PP) and Ce(IV) can electrolessly form thin conducting polymer films on their surface. We describe the effect of substituting every second PP layer in the (PP/Ce) multilayers for graphene oxide (GO) as a means of modifying the structure and mechanical properties of these (GO/Ce/PP/Ce) films and enhancing their growth. Both types of LbL films are based on reversible coordinative bonding between the metal ions and the oxygen-bearing groups in PP and GO, instead of purely electrostatic interactions. The GO incorporation leads to the doubling of the areal mass density and to a dry film thickness close to 300 nm after 4 (GO/Ce/PP/Ce) tetralayers. The film roughness increases significantly with thickness. The (PP/Ce) films are soft materials with approximately equal shear storage and loss moduli, but the incorporation of GO doubles the storage modulus. PP displays a marked terminating layer effect and practically eliminates mechanical losses, making the (GO/Ce/PP/Ce) films almost pure soft elastomers. The smoothness of the (PP/Ce) films and the PP-termination effects are attributed to the reversible coordinative bonding. The (GO/Ce/PP/Ce) films oxidize pyrrole and 3,4-ethylenedioxythiophene (EDOT) and form polypyrrole and PEDOT films on their surfaces. These polymer films are considerably thicker than those formed using the (PP/Ce) multilayers with the same nominal amount of cerium layers. The GO sheets interfere with the polymerization reaction and make its kinetics biphasic. The (GO/Ce) multilayers without PP are brittle and thin.

Three-dimensional graphene-based polymer nanocomposites: preparation, properties and applications

Motivated by the unique structure and outstanding properties of graphene, three-dimensional (3D) graphene-based polymer nanocomposites (3D-GPNCs) are considered as new generation materials for various multi-functional applications. This review presents an overview of the preparation, properties and applications of 3D-GPNCs. Three main approaches for fabricating 3D-GPNCs, namely 3D graphene based template, polymer particle/foam template, and organic molecule cross-linked graphene, are introduced. A thorough investigation and comparison of the mechanical, electrical and thermal properties of 3D-GPNCs are performed and discussed to understand their structure-property relationship. Various potential applications of 3D-GPNCs, including energy storage and conversion, electromagnetic interference shielding, oil/water separation, and sensors, are reviewed. Finally, the current challenges and outlook of these emerging 3D-GPNC materials are also discussed.

Incorporation of graphene oxide in polyethersulfone mixed matrix membranes to enhance hemodialysis membrane performance

Graphene is a carbon allotrope and possesses numerous unique properties which make it an attractive material in many areas. In this work, graphene oxide (GO) was added to polyethersulfone (PES) mixed matrix membranes (MMMs) to improve the performance of hemodialysis membranes. GO was synthesized from tartaric acid by pyrolysis with various temperatures of the pyrolysis and the membrane was fabricated by a casting solution method followed by its characterization. The MMMs showed better mechanical properties than pristine PES with a tensile stress and tensile strain value of 5.55 MPa and 0.039 m, respectively. The hydrophilicity of the membranes which is in agreement with contact angle values showed that GO addition increased the hydrophilicity of the MMMs. Hence, the solute flux and clearance of creatinine gave values of 2.94 L m⁻² h⁻¹ and 78.3%, respectively. Cross sectional images and the surface morphology were also recorded using scanning electron microscopy (SEM). The resulting data proved that the modified MMMs can be a potential material for hemodialysis.

In this work, graphene oxide (GO) was added to polyethersulfone (PES) mixed matrix membranes (MMMs) to improve the performance of hemodialysis membranes.

Study of Graphene Oxide Structural Features for Catalytic, Antibacterial, Gas Sensing, and Metals Decontamination Environmental Applications

This study represents a comprehensive review about the structural features of graphene oxide (GO) and its significance in environmental applications. Two dimensional (2D) GO is tremendously focused in advanced carbon-based nanomaterials for environmental applications due to its tunable physicochemical characteristics. Herein, we report foundational structural models of GO and explore the chemical bonding of oxygen moieties, with graphite basal plane using various characterization tools. Moreover, the impact of these oxygen moieties and the morphology of GO for environmental applications such as removal of metal ions and catalytic, antibacterial, and gas sensing abilities have here been critically reviewed for the first time. Environmental applications of GO are highly significant because, in the recent era, the fast progress of industries, even in the countryside, results in air and water pollution. GO has been widely investigated by researchers to eradicate such environmental issues and for potential industrial and clinical applications due to its 2D structural features, large surface area, presence of oxygen moieties, nonconductive nature, intense mechanical strength, excellent water dispersibility, and tunable optoelectronic properties. Thence, particular emphasis is directed toward the modification of GO by varying the number of its oxygen functional groups and by coupling it with other exotic nanomaterials to induce unique properties in GO for potential environmental remediation purposes.

Influence of 3-aminopropyltriethoxysilane- graphite oxide composite on thermal stability and mechanical property of polyethersulfone

Graphite oxide (GO) was modified using 3-aminopropyltriethoxysilane (APTES) for the fabrication of sheet type APTES–GO composite. Then, this composite was incorporated into the polyethersulfone (PES) matrix to enhance the thermal and mechanical properties of this polymer. The influence of APTES–GO composite on the thermal stability and mechanical property of PES was evaluated. The surface modification of GO by interacting with APTES could be an effective method to improve the compatibility and dispersion of GO sheets within the PES matrix. In comparison with those of virgin PES and GO/PES composites, the thermal decomposition temperature of PES composites containing well-dispersed APTES–GO sheets increased by 18.7°C. The tensile strength, tensile modulus, flexural strength, and flexural modulus of PES composite reinforced with 1.0 wt% APTES–GO sheets were enhanced by 21.1%, 15.2%, 15.4%, and 12.8%, respectively. The enhancement in thermal stability and mechanical property of APTES–GO/PES composite can be attributed to the uniform dispersion of APTES–GO sheets in the PES matrix as well as the strong interfacial interaction between them.