Smart Bandage Based on a ZIF-8 Triboelectric Nanogenerator for In Situ Real-Time Monitoring of Drug Concentration

For chronic wounds, frequent replacement of bandages not only increases the likelihood of secondary damage and the risk of cross infection but also wastes medication. Therefore, in situ real-time monitoring of the concentrations of residual drugs in bandages is crucial. Here, we propose a novel strategy that combines a triboelectric nanogenerator (TENG) with medical bandages to develop a smart bandage based on zeolite imidazolate framework TENG. During the process of wound healing, the electrical output of TENG changes with the continuous release of drugs. Based on the correlation between the electrical signal of TENG and drug concentration, the concentration of residual drugs in the bandage can be monitored in real-time in situ, guiding medical staff to replace the bandage at the most appropriate time. The smart bandage based on TENG provides a new strategy for in situ real-time monitoring of drug concentration and also provides an ideal and feasible solution for the field of biomedical drug sensing.

Affinity purification/immobilization of poly histidine-tagged proteins by nickel-functionalized porous chitosan membranes

Although immobilized metal ion affinity chromatography (IMAC) is one of the most effective methods for purifying his-tagged proteins, it has limitations such as expensive commercial resins and non-specific binding of unwanted proteins to the nickel immobilized on the resin. In this study, biocompatible chitosan and porous chitosan membranes as alternative resins were synthesized for protein immobilization and purification, but finally porous chitosan membrane was selected due to its higher porosity and consequently higher nickel adsorption. Once the membrane was functionalized with nickel ions and its metal adsorption confirmed by EDS and ICP methods, it was used to immobilize and purify recombinant β-NGF as a protein model with his-tag tail in batch-fashion. Protein binding and purification were also approved by FTIR and UV-Vis spectroscopy and SDS-PAGE technique. Our results indicated that the protein of interest could bind to the nickel-functionalized porous chitosan membrane with high efficiency at pH=7. Furthermore, for protein purification, the pH value of 6 and an imidazole concentration of 750 mM were suggested for the final elution buffer. In conclusion, nickel-functionalized porous chitosan membrane could be a suitable alternative to IMAC for low cost and specific protein immobilization and purification.

Electrospun zein nanofibers loaded with curcumin as a wound dressing: enhancing properties with PSS and PDADMAC layers

Development of wound dressings with enhanced therapeutic properties is of great interest in the modern healthcare. In this study, a zein-based nanofibrous wound dressing containing curcumin as a therapeutic agent was fabricated through electrospinning technique. In order to achieve desirable properties, such as antibacterial characteristics, reduced contact angle, and enhanced mechanical properties, the layer-by-layer technique was used for coating the surfaces of drug-loaded nanofibers by sequentially incorporating poly (sodium 4-styrene sulfonate) as a polyanion and poly (diallyldimethylammonium chloride) (PDADMAC) as a polycation. Various analyses, including scanning electron microscopy, Fourier transform infrared spectroscopy, drug release assessment., and mechanical tests were employed to assess the characteristics of the prepared wound dressings. Based on the results, coating with polyelectrolytes enhanced the Young's modulus and tensile strength of the electrospun mat from 1.34 MPa and 4.21 MPa to 1.88 MPa and 8.83 MPa, respectively. The coating also improved the controlled release of curcumin and antioxidant activity, while the outer layer, PDADMAC, exhibited antibacterial properties. The cell viability tests proved the appropriate biocompatibility of the prepared wound dressings. Moreover, our findings show that incorporation of the coating layers enhances cell migration and provides a favorable surface for cell attachment. According to the findings of this study, the fabricated nanofibrous wound dressing can be considered a promising and effective therapeutic intervention for wound management, facilitating the healing process.

Development of Cissus quadrangularis-Loaded POSS-Reinforced Chitosan-Based Bilayer Sponges for Wound Healing Applications: Drug Release and In Vitro Bioactivity

Nowadays, antibiotic-loaded biomaterials have been widely used in wound healing applications. However, the use of natural extracts has come into prominence as an alternative to these antimicrobial agents in the recent period. Among natural sources, Cissus quadrangularis (CQ) herbal extract is used for treatment of bone and skin diseases in ayurvedic medicine due to its antibacterial and anti-inflammatory effects. In this study, chitosan-based bilayer wound dressings were fabricated with electrospinning and freeze-drying techniques. CQ extract-loaded chitosan nanofibers were coated on chitosan/POSS nanocomposite sponges using an electrospinning method. The bilayer sponge is designed to treat exudate wounds while mimicking the layered structure of skin tissue. Bilayer wound dressings were investigated with regard to the morphology and physical and mechanical properties. In addition, CQ release from bilayer wound dressings and in vitro bioactivity studies were performed to determine the effect of POSS nanoparticles and CQ extract loading on NIH/3T3 and HS2 cells. The morphology of nanofibers was investigated with SEM analysis. Physical characteristics of bilayer wound dressings were determined with FT-IR analysis, swelling study, open porosity determination, and mechanical test. The antimicrobial activity of CQ extract released from bilayer sponges was investigated with a disc diffusion method. Bilayer wound dressings' in vitro bioactivity was examined using cytotoxicity determination, wound healing assay, proliferation, and the secretion of biomarkers for skin tissue regeneration. The nanofiber layer diameter was obtained in the range of 77.9-97.4 nm. The water vapor permeability of the bilayer dressing was obtained as 4021 to 4609 g/m²day, as it is in the ideal range for wound repair. The release of the CQ extract over 4 days reached 78-80% cumulative release. The release media were found to be antibacterial against Gram-negative and Gram-positive bacteria. In vitro studies showed that both CQ extract and POSS incorporation induced cell proliferation as well as wound healing activity and collagen deposition. As a result, CQ-loaded bilayer CHI-POSS nanocomposites were found as a potential candidate for wound healing applications.

How to Promote Skin Repair? In-Depth Look at Pharmaceutical and Cosmetic Strategies

Skin repair encompasses epidermal barrier repair and wound healing which involves multiple cellular and molecular stages. Therefore, many skin repair strategies have been proposed. In order to characterize the usage frequency of skin repair ingredients in cosmetics, medicines, and medical devices, commercialized in Portuguese pharmacies and parapharmacies, a comprehensive analysis of the products' composition was performed. A total of 120 cosmetic products, collected from national pharmacies online platforms, 21 topical medicines, and 46 medical devices, collected from INFARMED database, were included in the study, revealing the top 10 most used skin repair ingredients in these categories. A critical review regarding the effectiveness of the top ingredients was performed and an in-depth analysis focused on the top three skin repair ingredients pursued. Results demonstrated that top three most used cosmetic ingredients were metal salts and oxides (78.3%), vitamin E and its derivatives (54.2%), and Centella asiatica (L.) Urb. extract and actives (35.8%). Regarding medicines, metal salts and oxides were also the most used (47.4%) followed by vitamin B5 and derivatives (23.8%), and vitamin A and derivatives (26.3%). Silicones and derivatives were the most common skin repair ingredients in medical devices (33%), followed by petrolatum and derivatives (22%) and alginate (15%). This work provides an overview of the most used skin repair ingredients, highlighting their different mechanisms of action, aiming to provide an up-to-date tool to support health professionals' decisions.

Preparation and characterization of Pullulan-based nanocomposite scaffold incorporating Ag-Silica Janus particles for bone tissue engineering

A nanocomposite bone scaffold was fabricated from pullulan, a natural extracellular polysaccharide. Pullulan (PULL) was blended with polyvinylpyrrolidone (PVP), and a nano-platform with ball-stick morphology, Ag-Silica Janus particles (Ag-Silica JPs), which were utilized to fabricate nanocomposite scaffold with enhanced mechanical and biological properties. The Ag-Silica JPs were synthesized via a one-step sol-gel method and used to obtain synergistic properties of silver and silica's antibacterial and bioactive effects, respectively. The synthesized Ag-Silica JPs were characterized by means of FE-SEM, DLS, and EDS. The PULL/PVP scaffolds containing Ag-Silica JPs, fabricated by the freeze-drying method, were evaluated by SEM, EDS, FTIR, XRD, ICP and biological analysis, including antibacterial activity, bioactivity, cell viability and cell culture tests. It was noted that increasing Ag-Silica JPs amounts to an optimum level (1% w/w) led to an improvement in compressive modulus and strength of nanocomposite scaffold, reaching 1.03 ± 0.48 MPa and 3.27 ± 0.18, respectively. Scaffolds incorporating Ag-Silica JPs also showed favorable antibacterial activity. The investigations through apatite forming ability of scaffolds in SBF indicated spherical apatite precipitates. Furthermore, the cell viability test proved the outstanding biocompatibility of nanocomposite scaffolds (more than 90%) confirmed by cell culture tests showing that increment of Ag-Silica JPs amounts led to better adhesion, proliferation, ALP activity and mineralization of MG-63 cells.

Asymmetric resorbable-based dental barrier membrane for periodontal guided tissue regeneration and guided bone regeneration: A review

Guided tissue regeneration (GTR) and guided bone regeneration (GBR) are two common dental regenerative treatments targeted at reconstructing damaged periodontal tissue and bone caused by periodontitis. During GTR/GBR treatment, a barrier membrane is placed in the interface between the soft tissue and the periodontal defect to inhibit soft tissue ingrowth and creating a space for the infiltration of slow-growing bone cells into the defect site. Recently, asymmetric resorbable-based barrier membrane has received a considerable attention as a new generation of GTR/GBR membrane. Despite numerous literatures about asymmetric-based membrane that had been published, there is lacks comprehensive review on asymmetric barrier membrane that particularly highlight the importance of membrane structure for periodontal regeneration. In this review, we systematically cover the latest development and advancement of various kinds of asymmetric barrier membranes used in periodontal GTR/GBR application. Herein, the ideal requirements for constructing a barrier membrane as well as the rationale behind the asymmetric design, are firstly presented. Various innovative methods used in fabricating asymmetric barrier membrane are being further discussed. Subsequently, the application and evaluation of various types of asymmetric barrier membrane used for GTR/GBR are compiled and extensively reviewed based on the recent literatures reported. Based on the existing gap in this field, the future research directions of asymmetric resorbable-based barrier membrane such as its combination potential with bone grafts, are also presented.

Poly(lactic acid)/poly(butylene succinate) dual-layer membranes with cellulose nanowhisker for heavy metal ion separation

In this study, poly(lactic acid) (PLA)/poly(butylene succinate) (PBS) dual-layer membranes filled with 0-3 wt% cellulose nanowhisker (CNWs) were fabricated with aim to remove metal ions from wastewater. An integrated method was employed in the membrane fabrication process by combining water vapor-induced and crystallization-induced phase inversions. The membrane thickness was measured in between 11 and 13 μm, which did not pose significant flux deviation during filtration process. The 3% CNW filled membrane showed prominent and well-laminated two layers structure. Meanwhile, the increase in CNWs from 0 to 3% loadings could improve the membrane porosity (43-74%) but reducing pore size (2.45-0.54 μm). The heat resistance of neat membrane enhanced by 1% CNW but decreased with loadings of 2-3% CNWs due to flaming behavior of sulphated nanocellulose. Membrane with 3% CNW displayed the tensile strength (23.5 MPa), elongation at break (7.1%), and Young's modulus (0.75 GPa) as compared to other samples. For wastewater filtration performance, the continuous operation test showed that 3% CNW filled membrane exhibited the highest removal efficiency for both cobalt and nickel metal ions reaching to 83% and 84%, respectively. We concluded that CNWs filled dual-layer membranes have potential for future development in the removal of heavy metal ions from wastewater streams.

Silica/Protein and Silica/Polysaccharide Interactions and Their Contributions to the Functional Properties of Derived Hybrid Wound Dressing Hydrogels

Multifunctional and biocompatible hydrogels are on the focus of wound healing treatments. Protein and polysaccharides silica hybrids are interesting wound dressing alternatives. The objective of this review is to answer questions such as why silica for wound dressings reinforcement? What are the roles and contributions of silane precursors and silica on the functional properties of hydrogel wound dressings? The effects of tailoring the porous, morphological, and chemical characteristics of synthetic silicas on the bioactivity of hybrid wound dressings hydrogels are explored in the first part of the review. This is followed by a commented review of the mechanisms of silica/protein and silica/polysaccharide interactions and their impact on the barrier, scaffold, and delivery matrix functions of the derived hydrogels. Such information has important consequences for wound healing and paves the way to multidisciplinary researches on the production, processing, and biomedical application of this kind of hybrid materials.

Thermal Stability and Dynamic Mechanical Properties of Poly(ε-caprolactone)/Chitosan Composite Membranes

Poly (ε-caprolactone) (PCL) and chitosan (CS) are widely used as biodegradable and biocompatible polymers with desirable properties for tissue engineering applications. Composite membranes (CS-PCL) with various blend ratios (CS:PCL, w/w) of 0:100, 5:95, 10:90, 15:85, 20:80, and 100:0 were successfully prepared by lyophilization. The thermal stabilities of the CS-PCL membranes were systematically characterized by thermogravimetric analysis (TG), dynamic thermogravimetry (DTG), and differential scanning calorimetry (DSC). It was shown that the blend ratio of PCL and CS had a significant effect on the thermal stability, hydrophilicity, and dynamic mechanical viscoelasticity of the CS-PCL membranes. All the samples in the experimental range exhibited high elasticity at low temperature and high viscosity at high temperatures by dynamic mechanical thermal analysis (DMTA). The performances of the CS-PCL membranes were at optimum levels when the blend ratio (w/w) was 10:90. The glass transition temperature of the CS-PCL membranes increased from 64.8 °C to 76.6 °C compared to that of the pure PCL, and the initial thermal decomposition temperature reached 86.7 °C. The crystallinity and porosity went up to 29.97% and 85.61%, respectively, while the tensile strength and elongation at the breakage were 20.036 MPa and 198.72%, respectively. Therefore, the 10:90 (w/w) blend ratio of CS/PCL is recommended to prepare CS-PCL membranes for tissue engineering applications.

Chemical and physical Chitosan modification for designing enzymatic industrial biocatalysts: How to choose the best strategy?

Chitosan is one of the most abundant natural polymer worldwide, and due to its inherent characteristics, its use in industrial processes has been extensively explored. Because it is biodegradable, biocompatible, non-toxic, hydrophilic, cheap, and has good physical-chemical stability, it is seen as an excellent alternative for the replacement of synthetic materials in the search for more sustainable production methodologies. Thus being, a possible biotechnological application of Chitosan is as a direct support for enzyme immobilization. However, its applicability is quite specific, and to overcome this issue, alternative pretreatments are required, such as chemical and physical modifications to its structure, enabling its use in a wider array of applications. This review aims to present the topic in detail, by exploring and discussing methods of employment of Chitosan in enzymatic immobilization processes with various enzymes, presenting its advantages and disadvantages, as well as listing possible chemical modifications and combinations with other compounds for formulating an ideal support for this purpose. First, we will present Chitosan emphasizing its characteristics that allow its use as enzyme support. Furthermore, we will discuss possible physicochemical modifications that can be made to Chitosan, mentioning the improvements obtained in each process. These discussions will enable a comprehensive comparison between, and an informed choice of, the best technologies concerning enzyme immobilization and the application conditions of the biocatalyst.

Fabrication of ciprofloxacin-loaded chitosan/polyethylene oxide/silica nanofibers for wound dressing application: In vitro and in vivo evaluations

Silica plays an effective role in collagen creation; hence, the degradation products of silica-based materials accelerate wound healing. In this regard, chitosan/polyethylene oxide/silica hybrid nanofibers were prepared by the combining the sol-gel method with electrospinning technique to accelerate the wound healing process. Ciprofloxacin, as an antibacterial drug, was then added to the electrospinning mixture. The nanofibers were characterized by SEM, EDX, X-ray mapping, TEM, TGA, FTIR, and XRD analysis. The degradation, swelling ratio, and release of ciprofloxacin were investigated in PBS. The prepared nanofiber could absorb water, maintain its morphological integrity during the degradation process, and gradually release ciprofloxacin. The nanofibers revealed an efficient antibacterial activity against Escherichia coli and Staphylococcus aureus. Cell viability assays showed that the nanofibers had no cytotoxicity against L929 mouse fibroblast and HFFF2 human foreskin fibroblast cell lines. The potential of the chitosan/polyethylene oxide/silica/ciprofloxacin nanofiber for healing full-thickness wound was assessed by applying the scaffold in the dorsal cutaneous wounds of the Balb/C mice. The white blood cell counts of the animals indicated the nanofiber-treated mice compared with the untreated ones had less infection and inflammation. According to the histopathologic data, the prepared nanofiber accelerated and enhanced tissue regeneration by increasing fibroblast cells and angiogenesis as well as decreasing the inflammation phase. The findings suggest that the prepared antibacterial scaffold with drug delivery properties could be an appropriate candidate for many medical and hygienic applications, especially as a bio-compatible and bio-degradable wound dressing.

Fabrication and Characterization of Novel Poly(D-lactic acid) Nanocomposite Membrane for Water Filtration Purpose

The development of membrane technology from biopolymer for water filtration has received a great deal of attention from researchers and scientists, owing to the growing awareness of environmental protection. The present investigation is aimed at producing poly(D-lactic acid) (PDLA) membranes, incorporated with nanocrystalline cellulose (NCC) and cellulose nanowhisker (CNW) at different loadings of 1 wt.% (PDNC-I, PDNW-I) and 2 wt.% (PDNC-II PDNW-II). From morphological characterization, it was evident that the nanocellulose particles induced pore formation within structure of the membrane. Furthermore, the greater surface reactivity of CNW particles facilitates in enhancing the surface wettability of membranes due to increased hydrophilicity. In addition, both thermal and mechanical properties for all nanocellulose filled membranes under investigation demonstrated significant improvement, particularly for PDNW-I-based membranes, which showed improvement in both aspects. The membrane of PDNW-I presented water permeability of 41.92 L/m²h, when applied under a pressure range of 0.1-0.5 MPa. The investigation clearly demonstrates that CNWs-filled PDLA membranes fabricated for this investigation have a very high potential to be utilized for water filtration purpose in the future.

Hollow Fiber Membranes of PCL and PCL/Graphene as Scaffolds with Potential to Develop In Vitro Blood-Brain Barrier Models

There is a huge interest in developing novel hollow fiber (HF) membranes able to modulate neural differentiation to produce in vitro blood-brain barrier (BBB) models for biomedical and pharmaceutical research, due to the low cell-inductive properties of the polymer HFs used in current BBB models. In this work, poly(ε-caprolactone) (PCL) and composite PCL/graphene (PCL/G) HF membranes were prepared by phase inversion and were characterized in terms of mechanical, electrical, morphological, chemical, and mass transport properties. The presence of graphene in PCL/G membranes enlarged the pore size and the water flux and presented significantly higher electrical conductivity than PCL HFs. A biocompatibility assay showed that PCL/G HFs significantly increased C6 cells adhesion and differentiation towards astrocytes, which may be attributed to their higher electrical conductivity in comparison to PCL HFs. On the other hand, PCL/G membranes produced a cytotoxic effect on the endothelial cell line HUVEC presumably related with a higher production of intracellular reactive oxygen species induced by the nanomaterial in this particular cell line. These results prove the potential of PCL HF membranes to grow endothelial cells and PCL/G HF membranes to differentiate astrocytes, the two characteristic cell types that could develop in vitro BBB models in future 3D co-culture systems.