A biodegradable and biocompatible regular nanopattern for large-scale selective cell growth

Fabrication of Nanostructured Polycaprolactone (PCL) Film Using a Thermal Imprinting Technique and Assessment of Antibacterial Function for Its Application

In the use of the medical devices, it is essential to prevent the attachment of bacteria to the device surface or to kill the attached bacteria. To kill bacteria, many researchers have used antibiotics or studied nanostructure-based antibacterial surfaces, which rely on mechanical antibacterial methods. Several polymers are widely used for device fabrication, one of which is polycaprolactone (PCL). PCL is biocompatible, biodegradable, easy to fabricate using 3D printing, relatively inexpensive and its quality is easily controlled; therefore, there are various approaches to its use in bio-applications. In addition, it is an FDA-approved material, so it is often used as an implantable material in the human body. However, PCL has no inherent antibacterial function, so it is necessary to develop antibacterial functions in scaffold or film-based PCL medical devices. In this study, process parameters for nanopillar fabrication were established through a simple thermal imprinting method with PCL. Finally, a PCL film with a flexible and transparent nanopillar structure was produced, and the mechano-bactericidal potential was demonstrated using only one PCL material. PCL with nanopillars showed bactericidal ability against Escherichia coli (E. coli) and Bacillus subtilis (B. subtilis) bacteria cultured on its surface that resulted in membrane damage and death due to contact with nanopillars. Additionally, bacteriostatic results were shown to inhibit bacterial growth and activity of Staphylococcus aureus (S. aureus) on PCL nanostructured columns. The fabricated nanopillar structure has confirmed that mechanically induced antibacterial function and can be applied to implantable medical devices.

Block copolymer nanopatterns affect cell spreading: Stem versus cancer bone cells

Bone healing after a tumor removal can be promoted by biomaterials that enhance the bone regeneration and prevent the tumor relapse. Herein, we obtained several nanopatterns by self-assembly of polystyrene-block-poly-(2-vinylpyridine) (PS-b-P2VP) with different molecular weights and investigated the adhesion and morphology of human bone marrow mesenchymal stem cells (BMMSC) and osteosarcoma cell line (SaOS-2) on these patterns aiming to identify topography and chemistry that promote bone healing. We analyzed > 2000 cells per experimental condition using imaging software and different morphometric descriptors, namely area, perimeter, aspect ratio, circularity, surface/area, and fractal dimension of cellular contour (FDC). The obtained data were used as inputs for principal component analysis, which showed distinct response of BMMSC and SaOS-2 to the surface topography and chemistry. Among the studied substrates, micellar nanopatterns assembled from the copolymer with high molecular weight promote the adhesion and spreading of BMMSC and have an opposite effect on SaOS-2. This nanopattern is thus beneficial for bone regeneration after injury or pathology, e.g. bone fracture or tumor removal.

Effectiveness of Direct Laser Interference Patterning and Peptide Immobilization on Endothelial Cell Migration for Cardio-Vascular Applications: An In Vitro Study

Endothelial coverage of an exposed cardiovascular stent surface leads to the occurrence of restenosis and late-stent thrombosis several months after implantation. To overcome this difficulty, modification of stent surfaces with topographical or biochemical features may be performed to increase endothelial cells’ (ECs) adhesion and/or migration. This work combines both strategies on cobalt-chromium (CoCr) alloy and studies the potential synergistic effect of linear patterned surfaces that are obtained by direct laser interference patterning (DLIP), coupled with the use of Arg-Gly-Asp (RGD) and Tyr-Ile-Gly-Ser-Arg (YIGSR) peptides. An extensive characterization of the modified surfaces was performed by using AFM, XPS, surface charge, electrochemical analysis and fluorescent methods. The biological response was studied in terms of EC adhesion, migration and proliferation assays. CoCr surfaces were successfully patterned with a periodicity of 10 µm and two different depths, D (≈79 and 762 nm). RGD and YIGSR were immobilized on the surfaces by CPTES silanization. Early EC adhesion was increased on the peptide-functionalized surfaces, especially for YIGSR compared to RGD. High-depth patterns generated 80% of ECs’ alignment within the topographical lines and enhanced EC migration. It is noteworthy that the combined use of the two strategies synergistically accelerated the ECs’ migration and proliferation, proving the potential of this strategy to enhance stent endothelialization.

Surface engineering and the application of laser-based processes to stents - A review of the latest development

Late in-stent thrombus and restenosis still represent two major challenges in stents’ design. Surface treatment of stent is attracting attention due to the increasing importance of stenting intervention for coronary artery diseases. Several surface engineering techniques have been utilised to improve the biological response in vivo on a wide range of biomedical devices. As a tailorable, precise, and ultra-fast process, laser surface engineering offers the potential to treat stent materials and fabricate various 3D textures, including grooves, pillars, nanowires, porous and freeform structures, while also modifying surface chemistry through nitridation, oxidation and coatings. Laser-based processes can reduce the biodegradable materials' degradation rate, offering many advantages to improve stents’ performance, such as increased endothelialisation rate, prohibition of SMC proliferation, reduced platelet adhesion and controlled corrosion and degradation. Nowadays, adequate research has been conducted on laser surface texturing and surface chemistry modification. Laser texturing on commercial stents has been also investigated and a promotion of performance of laser-textured stents has been proved.

In this critical review, the influence of surface texture and surface chemistry on stents performance is firstly reviewed to understand the surface characteristics of stents required to facilitate cellular response. This is followed by the explicit illustration of laser surface engineering of stents and/or related materials. Laser induced periodic surface structure (LIPSS) on stent materials is then explored, and finally the application of laser surface modification techniques on latest generation of stent devices is highlighted to provide future trends and research direction on laser surface engineering of stents.

•

Compared conventional surface engineering with laser-based methods for biomedical devices.

•

Explained the influence of texture geometry and surface chemistry on stents biological response.

•

Reviewed state of the art in laser surface engineering of stents for improved biological response.

•

Reviewed state of the art in laser surface engineering to control degradation of bioresorbable stents.

•

Highlighted novel laser surface engineering designs for improved stents'performance.

A micron-scale surface topography design reducing cell adhesion to implanted materials

The micron-scale surface topography of implanted materials represents a complementary pathway, independent of the material biochemical properties, regulating the process of biological recognition by cells which mediate the inflammatory response to foreign bodies. Here we explore a rational design of surface modifications in micron range to optimize a topography comprised of a symmetrical array of hexagonal pits interfering with focal adhesion establishment and maturation. When implemented on silicones and hydrogels in vitro, the anti-adhesive topography significantly reduces the adhesion of macrophages and fibroblasts and their activation toward effectors of fibrosis. In addition, long-term interaction of the cells with anti-adhesive topographies markedly hampers cell proliferation, correlating the physical inhibition of adhesion and complete spreading with the natural progress of the cell cycle. This solution for reduction in cell adhesion can be directly integrated on the outer surface of silicone implants, as well as an additive protective conformal microstructured biocellulose layer for materials that cannot be directly microstructured. Moreover, the original geometry imposed during manufacturing of the microstructured biocellulose membranes are fully retained upon in vivo exposure, suggesting a long lasting performance of these topographical features after implantation.

Design and Applications of Cell-Selective Surfaces and Interfaces

Tissue regeneration involves versatile types of cells. The accumulation and disorganized behaviors of undesired cells impair the natural healing process, leading to uncontrolled immune response, restenosis, and/or fibrosis. Cell-selective surfaces and interfaces can have specific and positive effects on desired types of cells, allowing tissue regeneration with restored structures and functions. This review outlines the importance of surfaces and interfaces of biomaterials with cell-selective properties. The chemical and biological cues including peptides, antibodies, and other molecules, physical cues such as topography and elasticity, and physiological cues referring mainly to interactions between cells-cells and cell-chemokines or cytokines are effective modulators for achieving cell selectivity upon being applied into the design of biomaterials. Cell-selective biomaterials have also shown practical significance in tissue regeneration, in particular for endothelialization, nerve regeneration, capture of stem cells, and regeneration of tissues of multiple structures and functions.

Insect Analogue to the Lotus Leaf: A Planthopper Wing Membrane Incorporating a Low-Adhesion, Nonwetting, Superhydrophobic, Bactericidal, and Biocompatible Surface

Nature has produced many intriguing and spectacular surfaces at the micro- and nanoscales. These small surface decorations act for a singular or, in most cases, a range of functions. The minute landscape found on the lotus leaf is one such example, displaying antiwetting behavior and low adhesion with foreign particulate matter. Indeed the lotus leaf has often been considered the "benchmark" for such properties. One could expect that there are animal counterparts of this self-drying and self-cleaning surface system. In this study, we show that the planthopper insect wing (Desudaba danae) exhibits a remarkable architectural similarity to the lotus leaf surface. Not only does the wing demonstrate a topographical likeness, but some surface properties are also expressed, such as nonwetting behavior and low adhering forces with contaminants. In addition, the insect-wing cuticle exhibits an antibacterial property in which Gram-negative bacteria (Porphyromonas gingivalis) are killed over many consecutive waves of attacks over 7 days. In contrast, eukaryote cell associations, upon contact with the insect membrane, lead to a formation of integrated cell sheets (e.g., among human stem cells (SHED-MSC) and human dermal fibroblasts (HDF)). The multifunctional features of the insect membrane provide a potential natural template for man-made applications in which specific control of liquid, solid, and biological contacts is desired and required. Moreover, the planthopper wing cuticle provides a "new" natural surface with which numerous interfacial properties can be explored for a range of comparative studies with both natural and man-made materials.

Biophysical Regulation of Cell Behavior-Cross Talk between Substrate Stiffness and Nanotopography

The stiffness and nanotopographical characteristics of the extracellular matrix (ECM) influence numerous developmental, physiological, and pathological processes in vivo. These biophysical cues have therefore been applied to modulate almost all aspects of cell behavior, from cell adhesion and spreading to proliferation and differentiation. Delineation of the biophysical modulation of cell behavior is critical to the rational design of new biomaterials, implants, and medical devices. The effects of stiffness and topographical cues on cell behavior have previously been reviewed, respectively; however, the interwoven effects of stiffness and nanotopographical cues on cell behavior have not been well described, despite similarities in phenotypic manifestations. Herein, we first review the effects of substrate stiffness and nanotopography on cell behavior, and then focus on intracellular transmission of the biophysical signals from integrins to nucleus. Attempts are made to connect extracellular regulation of cell behavior with the biophysical cues. We then discuss the challenges in dissecting the biophysical regulation of cell behavior and in translating the mechanistic understanding of these cues to tissue engineering and regenerative medicine.

Diversity of Cuticular Micro- and Nanostructures on Insects: Properties, Functions, and Potential Applications

Insects exhibit a fascinating and diverse range of micro- and nanoarchitectures on their cuticle. Beyond the spectacular beauty of such minute structures lie surfaces evolutionarily modified to act as multifunctional interfaces that must contend with a hostile, challenging environment, driving adaption so that these can then become favorable. Numerous cuticular structures have been discovered this century; and of equal importance are the properties, functions, and potential applications that have been a key focus in many recent studies. The vast range of insect structuring, from the most simplistic topographies to the most elegant and geometrically complex forms, affords us with an exhaustive library of natural templates and free technologies to borrow, replicate, and employ for a range of applications. Of particular importance are structures that imbue cuticle with antiwetting properties, self-cleaning abilities, antireflection, enhanced color, adhesion, and antimicrobial and specific cell-attachment properties.

Material- and feature-dependent effects on cell adhesion to micro injection moulded medical polymers

Two polymers, polymethylmethacrylate (PMMA) and cyclic olefin copolymer (COC), containing a range of nano- to micron- roughness surfaces (Ra 0.01, 0.1, 0.4, 1.0, 2.0, 3.2 and 5.0μm) were fabricated using electrical discharge machining (EDM) and replicated using micro injection moulding (μIM). Polymer samples were characterized using optical profilometry, atomic force microscopy (AFM) and water surface contact angle. Cell adhesion tests were carried out using bacterial Pseudomonas fluorescens and mammalian Madin-Darby Canine Kidney (MDCK) cells to determine the effect of surface hydrophobicity, surface roughness and stiffness. It is found that there are features which gave insignificant differences (feature-dependent effect) in cell adhesion, albeit a significant difference in the physicochemical properties (material-dependent effect) of substrata. In bacterial cell adhesion, the strongest feature-dependence is found at Ra 0.4μm surfaces, with material-dependent effects strongest at Ra 0.01μm. Ra 0.1μm surfaces exhibited strongest feature-dependent effects and Ra 5.0μm has strongest material-dependent effects on mammalian cell adhesion. Bacterial cell adhesion is found to be favourable to hydrophobic surfaces (COC), with the lowest adhesion at Ra 0.4μm for both materials. Mammalian cell adhesion is lowest in Ra 0.1μm and highest in Ra 1.0μm, and generally favours hydrophilic surfaces (PMMA). These findings can be used as a basis for developing medical implants or microfluidic devices using micro injection moulding for diagnostic purposes, by tuning the cell adhesion on different areas containing different surface roughnesses on the diagnostic microfluidic devices or medical implants.

Effects of Line and Pillar Array Microengineered SiO2 Thin Films on the Osteogenic Differentiation of Human Bone Marrow-Derived Mesenchymal Stem Cells

A primary goal in bone tissue engineering is the design of implants that induce controlled, guided, and rapid healing. The events that normally lead to the integration of an implant into bone and determine the performance of the device occur mainly at the tissue-implant interface. Topographical surface modification of a biomaterial might be an efficient tool for inducing stem cell osteogenic differentiation and replace the use of biochemical stimuli. The main goal of this work was to develop micropatterned bioactive silica thin films to induce the osteogenic differentiation of human bone marrow-derived mesenchymal stem cells (hMSCs) only through topographical stimuli. Line and pillar micropatterns were developed by a combination of sol-gel/soft lithography and characterized by scanning electron microscopy, atomic force microscopy, and contact angle measurements. hMSCs were cultured onto the microfabricated thin films and flat control for up to 21 days under basal conditions. The micropatterned groups induced levels of osteogenic differentiation and expression of osteoblast-associated markers higher than those of the flat controls. Via comparison of the micropatterns, the pillars caused a stronger response of the osteogenic differentiation of hMSCs with a higher level of expression of osteoblast-associated markers, ALP activity, and extracellular matrix mineralization after the cells had been cultured for 21 days. These findings suggest that specific microtopographic cues can direct hMSCs toward osteogenic differentiation.

In situ Endothelialization: Bioengineering Considerations to Translation

Improving patency rates of current cardiovascular implants remains a major challenge. It is widely accepted that regeneration of a healthy endothelium layer on biomaterials could yield the perfect blood-contacting surface. Earlier efforts in pre-seeding endothelial cells in vitro demonstrated success in enhancing patency, but translation to the clinic is largely hampered due to its impracticality. In situ endothelialization, which aims to create biomaterial surfaces capable of self-endothelializing upon implantation, appears to be an extremely promising solution, particularly with the utilization of endothelial progenitor cells (EPCs). Nevertheless, controlling cell behavior in situ using immobilized biomolecules or physical patterning can be complex, thus warranting careful consideration. This review aims to provide valuable insight into the rationale and recent developments in biomaterial strategies to enhance in situ endothelialization. In particular, a discussion on the important bio-/nanoengineering considerations and lessons learnt from clinical trials are presented to aid the future translation of this exciting paradigm.

A gecko skin micro/nano structure - A low adhesion, superhydrophobic, anti-wetting, self-cleaning, biocompatible, antibacterial surface

Geckos, and specifically their feet, have attracted significant attention in recent times with the focus centred around their remarkable adhesional properties. Little attention however has been dedicated to the other remaining regions of the lizard body. In this paper we present preliminary investigations into a number of notable interfacial properties of the gecko skin focusing on solid and aqueous interactions. We show that the skin of the box-patterned gecko (Lucasium sp.) consists of dome shaped scales arranged in a hexagonal patterning. The scales comprise of spinules (hairs), from several hundred nanometres to several microns in length, with a sub-micron spacing and a small radius of curvature typically from 10 to 20 nm. This micro and nano structure of the skin exhibited ultralow adhesion with contaminating particles. The topography also provides a superhydrophobic, anti-wetting barrier which can self clean by the action of low velocity rolling or impacting droplets of various size ranges from microns to several millimetres. Water droplets which are sufficiently small (10-100 μm) can easily access valleys between the scales for efficient self-cleaning and due to their dimensions can self-propel off the surface enhancing their mobility and cleaning effect. In addition, we demonstrate that the gecko skin has an antibacterial action where Gram-negative bacteria (Porphyromonas gingivalis) are killed when exposed to the surface however eukaryotic cell compatibility (with human stem cells) is demonstrated. The multifunctional features of the gecko skin provide a potential natural template for man-made applications where specific control of liquid, solid and biological contacts is required.

Sub-micron lateral topography affects endothelial migration by modulation of focal adhesion dynamics

Through the interaction with topographical features, endothelial cells tune their ability to populate target substrates, both in vivo and in vitro. Basal textures interfere with the establishment and maturation of focal adhesions (FAs) thus inducing specific cell-polarization patterns and regulating a plethora of cell activities that govern the overall endothelial function. In this study, we analyze the effect of topographical features on FAs in primary human endothelial cells. Reported data demonstrate a functional link between FA dynamics and cell polarization and spreading on structured substrates presenting variable lateral feature size. Our results reveal that gratings with 2 µm lateral periodicity maximize contact guidance. The effect is linked to the dynamical state of FAs. We argue that these results are readily applicable to the rational design of active surfaces at the interface with the blood stream.

Tuning the surface properties of hydrogel at the nanoscale with focused ion irradiation

With the site-specific machining capability of Focused Ion Beam (FIB) irradiation, we aim to tailor the surface morphology and physical attributes of biocompatible hydrogel at the nano/micro scale particularly for tissue engineering and other biomedical studies. Thin films of Gtn-HPA/CMC-Tyr hydrogels were deposited on a gold-coated substrate and were subjected to irradiation with a kiloelectronvolt (keV) gallium ion beam. The sputtering yield, surface morphology and mechanical property changes were investigated using Scanning Electron Microscopy (SEM), Atomic Force Microscopy (AFM) and Monte Carlo simulations. The sputtering yield of the hydrogel was found to be approximately 0.47 μm(3) nC(-1) compared with Monte-Carlo simulation results of 0.09 μm(3) nC(-1). Compared to the surface roughness of the pristine hydrogel at approximately 2 nm, the average surface roughness significantly increased with the increase of ion fluence with measurements extended to 20 nm at 100 pC μm(-2). Highly packed submicron porous patterns were also revealed with AFM, while significantly decreased pore sizes and increased porosity were found with ion irradiation at oblique incidence. The Young's modulus of irradiated hydrogel determined using AFM force spectroscopy was revealed to be dependent on ion fluence. Compared to the original Young's modulus value of 20 MPa, irradiation elevated the value to 250 MPa and 350 MPa at 1 pC μm(-2) and 100 pC μm(-2), respectively. Cell culture studies confirmed that the irradiated hydrogel samples were biocompatible, and the generated nanoscale patterns remained stable under physiological conditions.

Nylon-3 polymers that enable selective culture of endothelial cells

Substrates that selectively encourage the growth of specific cell types are valuable for the engineering of complex tissues. Some cell-selective peptides have been identified from extracellular matrix proteins; these peptides have proven useful for biomaterials-based approaches to tissue repair or regeneration. However, there are very few examples of synthetic materials that display selectivity in supporting cell growth. We describe nylon-3 polymers that support in vitro culture of endothelial cells but do not support the culture of smooth muscle cells or fibroblasts. These materials may be promising for vascular biomaterials applications.

Directing vascular cell selectivity and hemocompatibility on patterned platforms featuring variable topographic geometry and size

It is great challenge to generate multifunctionality of vascular grafts and stents to enable vascular cell selectivity and improve hemocompatibility. Micro/nanopatterning of vascular implant surfaces for such multifunctionality is a direction to be explored. We developed a novel patterned platform featuring two typical geometries (groove and pillar) and six pattern sizes (0.5-50 μm) in a single substrate to evaluate the response of vascular cells and platelets. Our results indicate that targeted multifunctionality can be indeed instructed by rationally designed surface topography. The pillars nonselectively inhibited the growth of endothelial and smooth muscle cells. By contrast, the grooves displayed selective effects: in a size-dependent manner, the grooves enhanced endothelialization but inhibited the growth of smooth muscle cells. Moreover, our studies suggest that topographic cues can affect response of vascular cells by regulating focal adhesion and stress fiber development, which define cytoskeleton organization and cell shape. Notably, both the grooves and the pillars at 1 μm size drastically reduced platelet adhesion and activation. Taken together, these findings suggest that the topographic pattern featuring 1 μm grooves may be the optimal design of surface multifunctionality that favors vascular cell selectivity and improves hemocompatibility.

Development of a novel 3D culture system for screening features of a complex implantable device for CNS repair

Tubular scaffolds which incorporate a variety of micro- and nanotopographies have a wide application potential in tissue engineering especially for the repair of spinal cord injury (SCI). We aim to produce metabolically active differentiated tissues within such tubes, as it is crucially important to evaluate the biological performance of the three-dimensional (3D) scaffold and optimize the bioprocesses for tissue culture. Because of the complex 3D configuration and the presence of various topographies, it is rarely possible to observe and analyze cells within such scaffolds in situ. Thus, we aim to develop scaled down mini-chambers as simplified in vitro simulation systems, to bridge the gap between two-dimensional (2D) cell cultures on structured substrates and three-dimensional (3D) tissue culture. The mini-chambers were manipulated to systematically simulate and evaluate the influences of gravity, topography, fluid flow, and scaffold dimension on three exemplary cell models that play a role in CNS repair (i.e., cortical astrocytes, fibroblasts, and myelinating cultures) within a tubular scaffold created by rolling up a microstructured membrane. Since we use CNS myelinating cultures, we can confirm that the scaffold does not affect neural cell differentiation. It was found that heterogeneous cell distribution within the tubular constructs was caused by a combination of gravity, fluid flow, topography, and scaffold configuration, while cell survival was influenced by scaffold length, porosity, and thickness. This research demonstrates that the mini-chambers represent a viable, novel, scale down approach for the evaluation of complex 3D scaffolds as well as providing a microbioprocessing strategy for tissue engineering and the potential repair of SCI.

Cell patterning with a heptagon acoustic tweezer--application in neurite guidance

Accurate control over positioning of cells is a highly desirable feature in tissue engineering applications since it allows, for example, population of substrates in a controlled fashion, rather than relying on random seeding. Current methods to achieve a differential distribution of cells mostly use passive patterning methods to change chemical, mechanical or topographic properties of surfaces, making areas differentially permissive to the adhesion of cells. However, these methods have no ad hoc control over the actual deposition of cells. Direct patterning methods like bioprinting offer good control over cell position, but require sophisticated instrumentation and are often cost- and time-intensive. Here, we present a novel electronically controlled method of generating dynamic cell patterns by acoustic trapping of cells at a user-determined position, with a heptagonal acoustic tweezer device. We demonstrate the capability of the device to create complex patterns of cells using the device's ability to re-position acoustic traps by using a phase shift in the acoustic wave, and by switching the configuration of active piezoelectric transducers. Furthermore, we show that by arranging Schwann cells from neonatal rats in a linear pattern we are able to create Bands of Büngner-like structures on a non-structured surface and demonstrate that these features are able to guide neurite outgrowth from neonatal rat dorsal root ganglia.

Engineering cellular response using nanopatterned bulk metallic glass

Nanopatterning of biomaterials is rapidly emerging as a tool to engineer cell function. Bulk metallic glasses (BMGs), a class of biocompatible materials, are uniquely suited to study nanopattern-cell interactions as they allow for versatile fabrication of nanopatterns through thermoplastic forming. Work presented here employs nanopatterned BMG substrates to explore detection of nanopattern feature sizes by various cell types, including cells that are associated with foreign body response, pathology, and tissue repair. Fibroblasts decreased in cell area as the nanopattern feature size increased, and fibroblasts could detect nanopatterns as small as 55 nm in size. Macrophages failed to detect nanopatterns of 150 nm or smaller in size, but responded to a feature size of 200 nm, resulting in larger and more elongated cell morphology. Endothelial cells responded to nanopatterns of 100 nm or larger in size by a significant decrease in cell size and elongation. On the basis of these observations, nondimensional analysis was employed to correlate cellular morphology and substrate nanotopography. Analysis of the molecular pathways that induce cytoskeletal remodeling, in conjunction with quantifying cell traction forces with nanoscale precision using a unique FIB-SEM technique, enabled the characterization of underlying biomechanical cues. Nanopatterns altered serum protein adsorption and effective substrate stiffness, leading to changes in focal adhesion density and compromised activation of Rho-A GTPase in fibroblasts. As a consequence, cells displayed restricted cell spreading and decreased collagen production. These observations suggest that topography on the nanoscale can be designed to engineer cellular responses to biomaterials.

On cell separation with topographically engineered surfaces

BACKGROUND

Topographical modifications of the surface influence several cell functions and can be exploited to modulate cellular activities such as adhesion, migration and proliferation. These complex interactions are cell-type specific, therefore engineered substrates featuring patterns of two or more different topographies may be used to obtain the selective separation of different cell lineages. This process has the potential to enhance the performance of biomedical devices promoting, for example, the local coverage with functional tissues while demoting the onset of inflammatory reactions.

FINDINGS & CONCLUSIONS

Here we present a computational tool, based on Monte Carlo simulation, which decouples the contribution of cell proliferation and migration and predicts the cell-separation performance of topographically engineered substrates. Additionally, we propose an optimization procedure to shape the topographically engineered areas of a substrate and obtain maximal cell separation.

Laminin adsorption on nanostructures: switching the molecular orientation by local curvature changes

This work addresses the influence that the nanometric features of biologically relevant surfaces have on the conformation and properties of adsorbed laminin. It was observed that the adsorption kinetics and the nanomorphology of laminin were affected by the change in local curvature of chemically homogeneous nanostructured surfaces. The nanostructured surfaces were prepared by exploiting the self-assembly process of carboxylated polystyrene NPs, with diameters of 45, 109, and 209 nm, onto a polyelectrolyte multilayer formed by alternate deposition of poly(acrylic acid) and poly(allylamine hydrochloride) on gold. The anchored polymeric NPs were finally coated with a homogeneous layer of poly(allylamine hydrochloride), providing three surfaces with different nanometric local curvature. Atomic force microscopy was employed to characterize the relevant morphological parameters of the nanostructured surfaces. Quartz crystal microbalance with dissipation monitoring was employed to determine the adsorbed mass of laminin as well as its adsorption rate as a function of the local surface curvature. A model is proposed to explain the higher and faster laminin adsorption on surfaces with lower local curvature, where a switching of laminin anchoring orientation from a side-on to an end-on geometry can be predicted by a simple curvature-dependent parameter, γ, connecting the average nanostructure height h and the macromolecule radius of gyration R(g). The results provide a framework to understand the dependence of biomolecule orientation on local nanostructure.

Label-free segmentation of Co-cultured cells on a nanotopographical gradient

The function and fate of cells is influenced by many different factors, one of which is surface topography of the support culture substrate. Systematic studies of nanotopography and cell response have typically been limited to single cell types and a small set of topographical variations. Here, we show a radical expansion of experimental throughput using automated detection, measurement, and classification of co-cultured cells on a nanopillar array where feature height changes continuously from planar to 250 nm over 9 mm. Individual cells are identified and characterized by more than 200 descriptors, which are used to construct a set of rules for label-free segmentation into individual cell types. Using this approach we can achieve label-free segmentation with 84% confidence across large image data sets and suggest optimized surface parameters for nanostructuring of implant devices such as vascular stents.

Influence of variable substrate geometry on wettability and cellular responses

In this report, we evaluate the impact of a systematic change to the extracellular environment on cell morphology and functionality by combining the inherent properties of biocompatible polymers such as polydimethylsiloxane and polycaprolactone with a specific surface response. By microstructuring pillars and pits on the substrates, varying spacing and height of the structures, we investigate the role of topography in fibroblast cell adhesion and viability. The change of wetting behaviour was tailored and evaluated in terms of contact angle measurements. It was shown that the range of micro-scale physical cues at the interface between the cells and the surrounding environment affects cell shape and migrations, indicating a tendency to respond differently to higher features of the micro-scale. We found that surface topography seems dominant over material wettability, fibroblasts responded to variations in topography by altering morphology and migrating along the direction of spacing among the features biased by the height of structures and not by the material. It is therefore possible to selectively influence either cell adhesion or morphology by choosing adequate topography of the surface. This work can impact in the design of biomaterials and can be applied to implanted biomedical devices, tissue engineering scaffolds and lab on chip devices.

Tunable two dimensional protein patterns through self-assembly nanosphere template

By the aim of constructing surfaces for multi-component and multifunctional bioassay, a microsphere lithography technique was employed to control the surface morphology. Two kinds of protein molecules (antibodies) were used as building blocks. As a result, dual-component biocompatible surfaces with alternate immunoglobulin micropatterns were fabricated. The employed antibodies included human Immunoglobulin G (IgG) and rabbit IgG, which composed nanometer scale surface arrays on the surfaces. The antibodies were identified specially by immunoreactions with labeled antigens of fluorescein isothiocyanate (FITC)-antihuman IgG and tetramethylrhodamine-5-(and 6)-isothiocyanate (TRITC)-antirabbit IgG. The immune responses were confirmed by confocal fluorescence (FL) microscopy. A study on the sensitivity and quantification was done by using surface-enhanced resonance Raman scattering (SERRS) spectroscopy. The obtained SERRS spectra showed satisfactory resolution in the multi-component detection objects. No interference was observed from inner- or interactions of detecting molecules. The detection limits for both of the antigens reached to as low as 1 ng/mL, which was comparable to FL method. Meanwhile, a good linear relationship between SERRS peak intensity and the logarithm of antigens' concentrations (from 1 ng/mL to 1 mg/mL) were observed. The results demonstrated that SERRS is a very promising detection technique for multi-component immunoassay, and has great potential applications in biotechnology and biochemistry.

A dual gradient assay for the parametric analysis of cell-surface interactions

Cellular response to microgrooves is addressed using a new assay format, comprising orthogonal gradients of continuously varied groove pitch and depth. Dual layer etch masks are created using a combination of micropatterning and plasma polymer deposition. A silicon substrate with a constant groove width of 8 μm and with ridge width increasing from 8 μm in 0.5 μm steps across 10 mm is fabricated by photolithography. A plasma-polymerized hexane film which is 120 nm thick at one end of these grooves, and 10 nm at the other, is deposited under a diffusion mask. Reactive etching of the patterned sample transfers a gradient of groove pitch and groove depth into the silicon substrate. A silicon master with a gradient of groove depth spanning more than two orders of magnitude (less than 10 nm to over 1000 nm) is used to create an injection molding inlay for mass replication of the screening topography. Polycarbonate replicas are molded for use in cell culture studies, and the functionality of the topography as a high-throughput screening platform is investigated. The response of MDCK, h-TERT fibroblasts, and LE2 endothelial cells is examined, in terms of attachment and morphological response to the variation in topographical cues, with the aim of pinpointing the optimal combination of groove pitch and depth to elicit a tailored response from each cell type. When the range of topographical features screened on a single substrate is considered, this new assay represents a significant step forward in the parametric design and analysis of topographical cues at the biomaterial interface.

The effect of nano-scale topography on keratinocyte phenotype and wound healing following burn injury

Topographic modulation of tissue response is an important consideration in the design and manufacture of a biomaterial. In developing new tissue therapies for skin, all levels of architecture, including the nanoscale need to be considered. Here we show that keratinocyte phenotype is affected by nanoscale changes in topography with cell morphology, proliferation, and migration influenced by the pore size in anodic aluminum oxide membranes. A membrane with a pore size of 300 nm, which enhanced cell phenotype in vitro, was used as a dressing to cover a partial thickness burn injury in the pig. Wounds dressed with the membrane showed evidence of advanced healing with significantly less organizing granulation tissue and more mature epidermal layers than control wounds dressed with a standard burns dressing. The results demonstrate the importance of nanoscale topography in modulating keratinocyte phenotype and skin wound healing.

Micro-/nano-engineered cellular responses for soft tissue engineering and biomedical applications

The development of biomedical devices and reconstruction of functional ex vivo tissues often requires the need to fabricate biomimetic surfaces with features of sub-micrometer precision. This can be achieved with the advancements in micro-/nano-engineering techniques, allowing researchers to manipulate a plethora of cellular behaviors at the cell-biomaterial interface. Systematic studies conducted on these 2D engineered surfaces have unraveled numerous novel findings that can potentially be integrated as part of the design consideration for future 2D and 3D biomaterials and will no doubt greatly benefit tissue engineering. In this review, recent developments detailing the use of micro-/nano-engineering techniques to direct cellular orientation and function pertinent to soft tissue engineering will be highlighted. Particularly, this article aims to provide valuable insights into distinctive cell interactions and reactions to controlled surfaces, which can be exploited to understand the mechanisms of cell growth on micro-/nano-engineered interfaces, and to harness this knowledge to optimize the performance of 3D artificial soft tissue grafts and biomedical applications.

The interactions of astrocytes and fibroblasts with defined pore structures in static and perfusion cultures

Open pores to maintain nutrient diffusion and waste removal after cell colonization are crucial for the successful application of constructs based on assembled membranes, in our case tubular scaffolds made of ɛ-polycaprolactone (PCL), for use in tissue engineering. Due to the complex three-dimensional structure and large size of such scaffolds needed for transplantable tissues, it is difficult to investigate the cell–pore interactions in situ. Therefore miniaturized bioreactors inside Petri dishes (30 mm in diameter), containing porous PCL or poly-dimethylsiloxane (PDMS) membranes, were developed to allow the interactions of different cells with defined pores to be investigated in situ during both static and perfusion cultures. Investigation of two different cell types (fibroblasts and cortical astrocytes) and how they interact with a range of pores (100–350 μm in diameter) for up to 50 days indicated that the cells either ‘covered’ or ‘bridged’ the pores. Three distinct behaviors were observed in the way cortical astrocytes interacted with pores, while fibroblasts were able to quickly bridge the pores based on consistent “joint efforts”. Our studies demonstrate that the distinct pore sealing behaviors of both cell types were influenced by pore size, initial cell density and culture period, but not by medium perfusion within the range of shear forces investigated. These findings form important basic data about the usability of pores within scaffolds that could inform the design and fabrication of suitable scaffolds for various applications in tissue engineering.