Extraordinary physical properties of functionalized graphene

Effect of Graphene on the Mechanical Properties of Recycled High-Density and High-Molecular-Weight Polyethylene Blends

This study uses an extrusion process to formulate blends based on recycled high-density and high-molecular-weight polyethylene (recHDPE, recHMWPE) for the manufacture of rainwater drainage pipes. The main objective of this project is to investigate the effects of incorporating graphene on the mechanical, thermal, and stress-cracking resistance properties of the recycled HDPE and HMWPE blends. Also, it aims to demonstrate that the addition of graphene may enable the use of different recycled polymers without compromising their properties. The effects of adding two amounts of graphene (0.5 and 1%) to recycled blends on the tensile and flexion properties, stress crack resistance (SCR) (using a notched crack ligament stress (NCLS) test), thermal behavior (using a differential scanning calorimeter (DSC) and a rheological plastometer) were investigated. The experimental results showed a significative enhancement when adding graphene in the SCR, some tensile properties (elongation at break and tensile strength), and flexural modulus. However, physical characterization showed that the samples containing 0.5% graphene exhibited lower crystallinity compared to the reference and, for the blend with 1% graphene, the fluidity also decreased for the blend filled with the graphene compared to the reference blend without any filler.

Stability and Electronic Structure of Nitrogen-Doped Graphene-Supported Cun (n = 1-5) Clusters in Vacuum and under Electrochemical Conditions: Toward Sensor and Catalyst Design

Here, we present a detailed computational study of the stability and the electronic structure of nitrogen-doped graphene (N4V2) supported Cun (n = 1-5) clusters, which are promising carbon-dioxide electroreduction catalysts. The binding of the clusters to the nitrogen-doped graphene and the electronic structure of these systems were investigated under vacuum and electrochemical conditions. The stability analysis showed that among the systems, the nitrogen-doped graphene bound Cu4 is the most stable in vacuum, while in an electrolyte, and at a negative potential, the N4V2-Cu3 is energetically more favorable. The ground state electronic structure of the nitrogen-doped graphene substrate undergoes topological phase transition, from a semimetallic state, and we observed a metallic and topologically trivial state after the clusters are deposited. The electrode potential adjusts the type and density of the charge carriers in the semimetallic models, while the structures containing copper exhibit bands which are deformed and relaxed by the modified number of electrons.

Recent advances in biological molecule detection based on a three-dimensional graphene structure

Graphene has become an attractive material in the field of electrochemical detection owing to its unique electrical properties. Although the simple stacking structures of two-dimensional (2D) graphene sheets can provide excellent detection properties, a macroscopic three-dimensional (3D) structure needs to be constructed to enhance its functional properties. Graphene with a 3D structure has elegant functions, unlike graphene with a 2D structure. These properties include a large specific surface area, easy loading of nanomaterials with electrocatalytic and redox functions, and so on. Herein, we outline the preparation methods (self-assembly, chemical vapor deposition, templates, and 3D printing) for 3D graphene structures for obtaining excellent detection performance and applications in detecting biological molecules, bacteria, and cells. Furthermore, this review focuses on the improvement of the detection performance and enhancement of the applicability of graphene-based electrochemical sensors. We hope that this article will provide a reference for the future development of electrochemical sensors based on 3D graphene composites.

Controllable Modulation of the Electronic Properties of a Two-Dimensional Ambipolar Semiconductor by Interface Ferroelectric Polarization

Precise control of charge carrier type and density of two-dimensional (2D) ambipolar semiconductors is the prerequisite for their applications in next-generation integrated circuits and electronic devices. Here, by fabricating a heterointerface between a 2D ambipolar semiconductor (hydrogenated germanene, GeH) and a ferroelectric substrate (PbMg1/3Nb2/3O3-PbTiO3, PMN-PT), fine-tuning of charge carrier type and density of GeH is achieved. Due to ambipolar properties, proper band gap, and high carrier mobility of GeH, by applying the opposite local bias (±8 V), a lateral polarization in GeH is constructed with a change of work function by 0.6 eV. Besides, the built-in polarization in GeH nanoflake could promote the separation of photoexcited electron-hole pairs, which lead to 4 times enhancement of the photoconductivity after poling by 200 V. In addition, a gradient regulation of the work function of GeH from 4.94 to 5.21 eV by adjusting the local substrate polarization is demonstrated, which could be used for data storage at the micrometer size by forming p-n homojunctions. This work of constructing such heterointerfaces provides a pathway for applying 2D ambipolar semiconductors in nonvolatile memory devices, photoelectronic devices, and next-generation integrated circuit.

Experimental, Theoretical and Numerical Studies on Thermal Properties of Lightweight 3D Printed Graphene-Based Discs with Designed Ad Hoc Air Cavities

The current state of the art on material science emphasizes recent research efforts aimed at designing novel materials characterized by low-density and advanced properties. The present article reports the experimental, theoretical and simulation results on the thermal behavior of 3D printed discs. Filaments of pure poly (lactic acid) PLA and filled with 6 wt% of graphene nanoplatelets (GNPs) are used as feedstocks. Experiments indicate that the introduction of graphene enhances the thermal properties of the resulting materials since the conductivity passes from the value of 0.167 [W/mK] for unfilled PLA to 0.335 [W/mK] for reinforced PLA, which corresponds to a significantly improvement of 101%. Exploiting the potential of 3D printing, different air cavities have been intentionally designed to develop new lightweight and more cost-effective materials without compromising their thermal performances. Furthermore, some cavities are equal in volume but different in the geometry; it is necessary to investigate how this last characteristic and its possible orientations affect the overall thermal behavior compared to that of an air-free specimen. The influence of air volume is also investigated. Experimental results are supported by theoretical analysis and simulation studies based on the finite element method. The results aim to be a valuable reference resource in the field of design and optimization of lightweight advanced materials.

A novel bioactive glass/graphene oxide composite coating for a polyether ether ketone-based dental implant

Polyether ether ketone (PEEK) is a biocompatible material that lacks antimicrobial activity and bioactivity; therefore, is not appropriate for use as a dental implant. To overcome these deficiencies, a novel composite coating of bioactive glass and graphene oxide was prepared. PEEK discs were polished, cleaned, and the surface treated with sulfuric acid for 15 min. The composite coating consisted of bioactive glass produced by the sol-gel route and doped with 0.75 wt% graphene oxide. X-ray diffraction, Fourier transform infrared spectroscopy, and scanning electron microscopy-energy dispersive spectroscopy analyses were employed to characterize the composite coating, and the coating adhesion strength quantified using a pull-off test. Cytotoxicity was assessed using osteoblast-like cells and gingival fibroblasts. The wettability of the coated and non-coated samples was determined by optical contact angle assessment, and bioactivity was assessed by immersion in simulated body fluid. The results revealed that the bioactive glass/graphene oxide composite coating, approximately 7 μm thick, was transparent, homogenous with few microcracks and microporosities, but adhered strongly and was not cytotoxic to either osteoblast-like cells or gingival fibroblasts. The wettability of the PEEK sample was increased to <20° after coating with the composite, and apatite formation was detectable after 14 days of immersion in simulated body fluid.

Antibacterial Enhancement of High-Efficiency Particulate Air Filters Modified with Graphene-Silver Hybrid Material

Bacterial infections are a major concern as antibiotic resistance poses a great threat, therefore leading to a race against time into finding new drugs or improving the existing resources. Nanomaterials with high surface area and bactericidal properties are the most promising ones that help combating microbial infections. In our case, graphene decorated with silver nanoparticles Gr-Ag (5 wt% Ag) exhibited inhibitory capacity against S. aureus and E. coli. The newly formed hybrid material was next incubated with high-efficiency particulate air (HEPA) filter, to obtain one with bactericidal properties. The modified filter had greater inhibitory action against the tested strains, compared to the control, and the effect was better against the Gram-negative model. Even if the bacteria remained attached to the filters, their colony forming unit capacity was affected by the Gr-Ag (5 wt% Ag) hybrid material, when they were subsequently re-cultured on fresh agar media. Therefore, the HEPA filter modified with Gr-Ag (5 wt% Ag) has high antibacterial properties that may substantially improve the existing technology.

Effects of Co-Solvent-Induced Self-Assembled Graphene-PVDF Composite Film on Piezoelectric Application

A persistent purpose for self-powered and wearable electronic devices is the fabrication of graphene-PVDF piezoelectric nanogenerators with various co-solvents that could provide enhanced levels of durability and stability while generating a higher output. This study resulted in a piezoelectric nanogenerator based on a composite film composed of graphene, and poly (vinylidene fluoride) (PVDF) as a flexible polymer matrix that delivers high performance, flexibility, and cost-effectiveness. By adjusting the co-solvent in the solution, a graphene-PVDF piezoelectric nanogenerator can be created (acetone, THF, water, and EtOH). The solution becomes less viscous and is more diluted the more significant the concentration of co-solvents, such as acetone, THF, and EtOH. Additionally, when the density is low, the thickness will be thinner. The final film thickness for all is ~25 µm. Furthermore, the- crystal phase becomes more apparent when graphene is added and combined with the four co-solvents. Based on the XRD results, the peak changes to the right, which can be inferred to be more dominant with the β-phase. THF is the co-solvent with the highest piezoelectric output among other co-solvents. Most of the output voltages produced are 0.071 V and are more significant than the rest.

Application of Nanomaterials to Enhance Polymerase Chain Reaction

Polymerase Chain Reaction (PCR) is one of the most common technologies used to produce millions of copies of targeted nucleic acid in vitro and has become an indispensable technique in molecular biology. However, it suffers from low efficiency and specificity problems, false positive results, and so on. Although many conditions can be optimized to increase PCR yield, such as the magnesium ion concentration, the DNA polymerases, the number of cycles, and so on, they are not all-purpose and the optimization can be case dependent. Nano-sized materials offer a possible solution to improve both the quality and productivity of PCR. In the last two decades, nanoparticles (NPs) have attracted significant attention and gradually penetrated the field of life sciences because of their unique chemical and physical properties, such as their large surface area and small size effect, which have greatly promoted developments in life science and technology. Additionally, PCR technology assisted by NPs (NanoPCR) such as gold NPs (Au NPs), quantum dots (QDs), and carbon nanotubes (CNTs), etc., have been developed to significantly improve the specificity, efficiency, and sensitivity of PCR and to accelerate the PCR reaction process. This review discusses the roles of different types of NPs used to enhance PCR and summarizes their possible mechanisms.

Production of Graphene Stably Dispersible in Ethanol by Microwave Reaction

Graphene is a 2D carbon material with peculiar features such as high electrical conductivity, high thermal conductivity, mechanical stability, and a high ratio between surface and thickness. Applications are continuously growing, and the possibility of dispersing graphene in low-boiling green solvents could reduce its global environmental impact. Pristine graphene can be dispersed in high concentration only in polar aprotic solvents that usually have high boiling points and high toxicity. For this reason, the oxidized form of graphene is always used, as it is easier to disperse and to subsequently reduce to reduced graphene oxide. However, compared to pristine graphene, reduced graphene oxide has more defects and has inferior properties respect to graphene. In this work, the polymerization of (diethyl maleate derivate) on graphene obtained by sonication was performed in a microwave reactor. The obtained material has good stability in ethanol even after a long period of time, therefore, it can be used to deposit graphene by mass production of inks or by casting and easy removal of the solvent. The thermal annealing by heating at 300–400 °C in inert atmosphere allows the removal of the polymer to obtain pristine graphene with a low number of defects.

A Polarization-Insensitive Broadband Terahertz Absorber Using Patterned Graphene

A polarization-insensitive broadband terahertz absorber with a sandwich structure of metal−dielectric-graphene is designed and simulated. The graphene is patterned as an array of graphene square blocks with circular apertures. The results of the simulations and theoretical analysis show that the absorption exceeds 99% from 0.93 to 1.65 THz while 90% from 0.80 to 1.87 THz, and a broad relative bandwidth of 80.2% is achieved. The absorption performance is passively enhanced by altering physical dimensions of the graphene pattern and actively adjusted by changing the chemical potential of graphene. When the chemical potential increases from 0.1 eV to 0.7 eV, the corresponding terahertz absorption increases from 59.1% to 99%. The mechanism of absorption is disclosed by analyzing the impedance matching theory and distribution of electric-field intensity. In addition, different polarization modes and incident angles are also studied. The proposed absorber has the superiorities of broad relative bandwidth, high absorption rate, polarization insensitivity, and a wide incident angle, which offers some potential applications in the field of terahertz technology such as imaging, detection, and cloaking.

Ab initio study for superior sensitivity of graphyne nanoflake towards nitrogen halides over ammonia

Graphyne (GYN) has received immense attention in gas adsorption applications due to its large surface area. The adsorption of toxic ammonia and nitrogen halides gaseous molecules on graphyne has been theoretically studied at ωB97XD/6-31 + G(d, p) level of DFT. The counterpoise corrected interaction energies of NH₃, NF₃, NCl₃, and NBr₃ molecules with GYN are - 4.73, - 2.27, - 5.22, and - 7.19 kcal mol^-1, respectively. Symmetry-adapted perturbation theory (SAPT0) and noncovalent interaction index (NCI) reveal that the noncovalent interaction between analytes and GYN is dominated by dispersion forces. The significant change in electronic behavior, i.e., energies of HOMO and LUMO orbitals and NBO charge transfer correspond to the pronounced sensitivity of GYN towards considered analytes, especially NBr₃. Finally, TD-DFT calculation reveals a decrease in electronic transition energies and shifting of adsorption to a longer wavelength. The recovery time for NX₃@GYN is observed in nanoseconds, which is many orders of magnitude smaller than the reported systems. The recovery time is further decreased with increasing temperature, indicating that the GYN benefits from a short recovery time as a chemical sensor.

Preparation and characterization of lignin/nano graphene oxide/styrene butadiene rubber composite for automobile tyre application

Styrene butadiene rubber (SBR), is a synthetic polymer and the most abundantly used in the tire industry, which have good collaborative properties with additives and fillers. In present work, we aim to synthesize SBR composite having the properties of graphene oxide filler and made it to be biodegradable. In composite preparation, we fabricated styrene-butadiene rubber/graphene oxide/lignin composites by adding biodegradable biomolecule of lignin fillers at varying 1-3 wt% quantities amount. Those prepared SBR composites were characterized using advanced analysis techniques, and also their biodegradability was. From microscopy examination results, the morphology of pure SBR composite had been improved after the addition of graphene oxide, while the 1 wt% lignin filled SBR sample revealed well-integrated morphology with crest-and-trough-like feature, showcasing the lignin fibrils could strengthen the molecular interaction between graphene oxide nano sheet and SBR rubber. For 2 wt% lignin filled SBR sample, it exhibited large protuberants due to the aggregation effect of lignin fibrils. However, bulky and bundle structure of protuberant was more significantly formed in 3 wt% lignin filled SBR, as a result of poor interface between lignin and SBR rubber. The porosity had also been improved for 1 wt% lignin filled SBR sample, imparting it with great surface area to act as tire in automobile application. The physico-chemical analysis also detected the trace of graphene oxide and lignin functional groups in the SBR composite. In addition, the thermal analysis revealed those lignin-filled composites had stable heat tolerance behavior, which suitably used in extreme weather condition. Moreover, the 1 wt% lignin filled SBR sample exhibited good characteristics in both mechanical and biodegradable properties. Thus, the composite of 1 wt% lignin filled SBR could be regarded as a promising candidate for green tire application in the future.

Preparation of Styrene-Butadiene Rubber (SBR) Composite Incorporated with Collagen-Functionalized Graphene Oxide for Green Tire Application

Styrene-butadiene rubber (SBR) is a synthetic polymer primarily used in the tire industry, due to its good collaborative properties with additives and fillers. In the present work, we aim to synthesize an SBR composite reinforced with graphene oxide filler to be made biodegradable. In composite preparation, we fabricated styrene-butadiene rubber/graphene oxide/collagen (SBR/GO/COL) composites by adding a biodegradable biomolecule of elastin collagen fillers at 1.5 wt% and 2.5 wt%. Those prepared SBR/GO/COL composites, along with pure SBR and SBR/GO as control samples, were characterized using advanced analysis techniques, and their biodegradability was also evaluated. From microscopy examination results, the morphology of pure SBR had been improved after the addition of GO for SBR/GO composite by revealing a compact structure with a smoother surface. As for the SBR/GO/1.5COL sample, the 1.5 wt% COL filler was found to be effectively embedded in the SBR/GO matrix. However, the 2.5 wt% COL amount led to the formation of an aggregated structure in the SBR/GO/2.5COL sample due to the unreacted interface between COL filler and SBR/GO. The porosity had also been improved for SBR/GO/1.5COL sample, imparting it with a surface area suitable for tires in the automobile industry. From elemental analysis, the presence of nitrogen was detected for the collagen-filled SBR composite, proving the successful incorporation of collagen fibrils. The physicochemical analysis also detected a trace of graphene oxide and collagen functional groups in the SBR composite. In addition, the thermal analysis revealed those collagen-filled composites had stable heat tolerance behavior, which is suitably used in extreme weather conditions. Moreover, the SBR/GO/1.5COL sample exhibited good characteristics in both mechanical and biodegradable properties. Thus, the product of SBR/GO/1.5COL could be regarded as a promising composite for green tires in the auto industry in the future.

Advances in Graphene/Inorganic Nanoparticle Composites for Catalytic Applications

Graphene-based nanocomposites with inorganic (metal and metal oxide) nanoparticles leads to materials with high catalytic activity for a variety of chemical transformations. Graphene and its derivatives such as graphene oxide, highly reduced graphene oxide, or nitrogen-doped graphene are excellent support materials due to their high surface area, their extended π-system, and variable functionalities for effective chemical interactions to fabricate nanocomposites. The ability to fine-tune the surface composition for desired functionalities enhances the versatility of graphene-based nanocomposites in catalysis. This review summarizes the preparation of graphene/inorganic NPs based nanocomposites and their use in catalytic applications. We discuss the large-scale synthesis of graphene-based nanomaterials. We have also highlighted the interfacial electronic communication between graphene/inorganic nanoparticles and other factors resulting in increased catalytic efficiencies.

Rapid and sensitive detection of PD-L1 exosomes using Cu-TCPP 2D MOF as a SPR sensitizer

Two-dimensional metal organic framework (2D MOF Cu-TCPP) with significantly enhanced photoelectric properties was synthesized by a simple hydrothermal method. The π-stacked electroactive porphyrin molecules of TCPP-based 2D MOF carry out charge transport in the MOF structure. The d-d band transition of Cu²⁺ and its 2D ultra-thin characteristics can produce excellent near-infrared light absorption to couple with SPR. Three key parameters including the refractive index sensitivity, detection accuracy and quality factor were improved significantly for 2D MOF modified gold chips. Especially, the refractive index sensitivity was increased from 98 to 137.67°/RIU after modified with 2D MOF. Thus, for the first time, we applied it as a signal enhancer to improve direct SPR assay for the Programmed death ligand-1 (PD-L1) exosomes. Owning to its large specific surface area, excellent photoelectric properties, highly ordered structure, good dispersion and biocompatibility, the LOD of the SPR sensor was 16.7 particles/mL. The reliability and practicability were further validated by analysis of PD-L1 exosomes in human serum samples. The recovery rate was 93.43 %-102.35%, with RSD of 5.79 %-14.6%. Given their excellent signal amplification ability, 2D MOF Cu-TCPP could serve as an ideal SPR sensitizer for rapid and sensitive detection of trace disease markers.

High electrochemical performance of ink solution based on manganese cobalt sulfide/reduced graphene oxide nano-composites for supercapacitor electrode materials

Large scale supercapacitor electrodes were prepared by 3D-printing directly on a graphite paper substrate from ink solution containing manganese cobalt sulfide/reduced graphene oxide (MCS/rGO) nanocomposites. The MCS/rGO composite solution was synthesized through the dispersion of MCS NPs and rGO in dimethylformamide (DMF) solvent at room temperature. Their morphology and composition were investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and energy dispersive X-ray diffraction (EDS). The role of rGO on decreasing charge transfer resistance and enhancing ion exchange was discussed. The MCS/rGO electrode exhibits an excellent specific capacitance of 3812.5 F g⁻¹ at 2 A g⁻¹ and it maintains 1780.8 F g⁻¹ at a high current density of 50 A g⁻¹. The cycling stability of the electrodes reveals capacitance retention of over 92% after 22 000 cycles at 50 A g⁻¹.

Large scale supercapacitor electrodes were prepared by 3D-printing directly on a graphite paper substrate from ink solution containing manganese cobalt sulfide/reduced graphene oxide (MCS/rGO) nanocomposites.

In-situ food spoilage monitoring using a wireless chemical receptor-conjugated graphene electronic nose

Monitoring food spoilage is one of the most effective methods for preventing food poisoning caused by biogenic amines or microbes. Therefore, various analytical techniques have been introduced to detect low concentrations of cadaverine (CV) and putrescine (PT), which are representative biogenic polyamines involved in food spoilage (5-8 ppm at the stage of initial decomposition after storage for 5 days at 5 °C and 17-186 ppm at the stage of advanced decomposition after storage for 7 days at 5 °C). Although previous methods showed selective CV and PT detection even at low concentrations, the use of these methods remains challenging in research areas that require in-situ, real-time, on-site monitoring. In this study, we demonstrated for the first time an in-situ high-performance chemical receptor-conjugated graphene electronic nose (CRGE-nose) whose limits of detection (LODs), 27.04 and 7.29 ppb, for CV and PT are up to 10² times more sensitive than those of conventional biogenic amine sensors. Specifically, the novel chemical receptors 2,7-bis(3-morpholinopropyl)benzo[lmn][3,8] phenanthroline-1,3,6,8(2H,7H)-tetraone (NaPhdiMor (NPM)) and 2,7-bis(2-((3-morpholinopropyl)amino)ethyl)benzo[lmn][3,8]phenanthroline-1,3,6,8(2H,7H)-tetraone (NaPhdiEtAmMor (NPEAM)) were designed on the basis of density functional theory (DFT) calculations, and their interaction mechanism was characterized by a DFT 3D simulation. Interestingly, the CRGE-nose was connected on a micro sim chip substrate via wire bonding and then integrated into wireless portable devices, resulting in a cost-effective, high-performance prototype CRGE-nose device capable of on-site detection. The portable CRGE-nose can be used for in-situ monitoring of CV and PT concentration changes as low as 27.04 and 7.29 ppb in real meats such as pork, beef, lamb and chicken.

Graphene and carbon nanotubes interfaced electrochemical nanobiosensors for the detection of SARS-CoV-2 (COVID-19) and other respiratory viral infections: A review

Recent COVID-19 pandemic has claimed millions of lives due to lack of a rapid diagnostic tool. Global scientific community is now making joint efforts on developing rapid and accurate diagnostic tools for early detection of viral infections to preventing future outbreaks. Conventional diagnostic methods for virus detection are expensive and time consuming. There is an immediate requirement for a sensitive, reliable, rapid and easy-to-use Point-of-Care (PoC) diagnostic technology. Electrochemical biosensors have the potential to fulfill these requirements, but they are less sensitive for sensing viruses/viral infections. However, sensitivity and performance of these electrochemical platforms can be improved by integrating carbon nanostructure, such as graphene and carbon nanotubes (CNTs). These nanostructures offer excellent electrical property, biocompatibility, chemical stability, mechanical strength and, large surface area that are most desired in developing PoC diagnostic tools for detecting viral infections with speed, sensitivity, and cost-effectiveness. This review summarizes recent advancements made toward integrating graphene/CNTs nanostructures and their surface modifications useful for developing new generation of electrochemical nanobiosensors for detecting viral infections. The review also provides prospects and considerations for extending the graphene/CNTs based electrochemical transducers into portable and wearable PoC tools that can be useful in preventing future outbreaks and pandemics.

Fabrication and Specific Functionalisation of Carbon Fibers for Advanced Flexible Biosensors

This review aims at offering an up-to-date comprehensive summary of carbon fibers (CFs)-based composites, with the emphasis on smart assembly and purpose-driven specific functionalization for their critical applications associated with flexible sensors. We first give a brief introduction to CFs as a versatile building block for preparation of mutil-fountional materials and the current status of research studies on CFs. This is followed by addressing some crucial methods of preparation of CFs. We then summarize multiple possibilities of functionalising CFs, an evaluation of some key applications of CFs in the areas of flexible biosensors was also carried out.

Graphene Oxide Composite for Selective Recognition, Capturing, Photothermal Killing of Bacteria over Mammalian Cells

The multifunctional photothermal therapy (PTT) platform with the ability to selectively kill bacteria over mammalian cells has received widespread attention recently. Herein, we prepared graphene oxide-amino(polyethyleneglycol) (GO-PEG-NH2) while using the hydrophobic interaction between heptadecyl end groups of 1,2-distearoyl-sn-glycero-3-phosphoethanolamine-N-[amino(polyethyleneglycol)] (DSPE-PEG-NH2) and graphene oxide (GO). Based on GO-PEG-NH2, the versatile PTT system was constructed with simultaneous selective recognition, capturing, and photothermal killing of bacteria. When the cells undergo bacterial infection, owing to the poly(ethylene glycol) (PEG) chains and positively charged amino groups, GO-PEG-NH2 can specifically recognize and capture bacteria in the presence of cells. Meanwhile, the stable photothermal performance of GO-PEG-NH2 enables the captured bacteria to be efficiently photothermally ablated upon the irradiation of 808 nm laser. Besides, the GO-PEG-NH2 is highly stable in various biological media and it exhibits low cytotoxicity, suggesting that it holds great promise for biological applications. This work provides new insight into graphene-based materials as a PTT agent for the development of new therapeutic platforms.

Bioactive Three-Dimensional Graphene Oxide Foam/Polydimethylsiloxane/Zinc Silicate Scaffolds with Enhanced Osteoinductivity for Bone Regeneration

Nanocomposite scaffold materials have shown great prospect in promoting bone integration and bone regeneration. A three-dimensional graphene oxide foam/polydimethylsiloxane/zinc silicate (GF/PDMS/ZS) scaffold for bone tissue engineering was synthesized via dip coating and hydrothermal synthesis processes, resulting in the interconnected macroporous structure. The scaffold was characterized with scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and thermogravimetric (TG) analysis. The result showed that scaffolds exhibiting a porous characteristic had organic-inorganic components similar to natural bone tissue. Moreover, the scaffolds possessed suitable pore size, high porosity, and good mechanical properties. In vitro experiments with mouse bone marrow mesenchymal stem cells (mBMSCs) revealed that the composite scaffold not only has great biocompatibility but also has the ability to induce mBMSC proliferation and preferential osteogentic differentiation. Thereafter, the expression of critical genes, ALP, RUNX2, VEGFA, and OPN, was activated. In vivo analysis of critical bone defect in rabbits demonstrated superior bone formation in defect sites in the GF/PDMS/ZS scaffold group at 12 weeks of post implantation without no significant inflammatory response. All the results validated that the GF/PDMS/ZS scaffold is a promising alternative for applications in bone regeneration.

Graphene based adsorbents for remediation of noxious pollutants from wastewater

The contamination of water resources with noxious pollutants is a serious issue. Many aquatic systems are contaminated with different toxic inorganic and organic species; coming to wastewater from various anthropogenic sources such as industries, agriculture, mining, and domestic households. Keeping in view of this, wastewater treatment appears to the main environmental challenge. Adsorption is one of the most efficient techniques for removing all most all types of pollutants i.e. inorganics and organics. Nowadays, graphene and its composite materials are gaining importance as nano adsorbents. Graphene; a two-dimensional nanomaterial having single-atom graphite layer; has attracted a great interest in many application areas (including wastewater treatment) due to its unique physico-chemical properties. The present paper is focused on the remediation of noxious wastes from wastewater using graphene based materials as adsorbents, and it contains all the details on materials - i.e., from their synthesis to application in the field of wastewater treatment (removal of hazardous contaminants of different chemical nature - heavy and rare-earth metal ions, and organic compounds - from wastewater effluents. The efficiency of the adsorption and desorption of these substances is considered. Certainly, this article will be useful for nano environmentalist to design future experiments for water treatment.

Achieving high yield of graphene nanoplatelets in poloxamer-assisted ultrasonication of graphite in water

The role of surfactant (Pluronic® F 127) concentration on the yield and morphological characteristics of graphene nanoplatelets (GNPs) produced from the sonication of aqueous graphene suspensions is investigated in this work. By employing a wide surfactant concentration range (0.1-15 wt%) and sonication power densities up to 420 W L^-1 we identify two graphene exfoliation regimes: the first occurs at low sonication power densities (<340 W L^-1) and produces GNPs with sizes 200-300 nm, aspect ratios between 70 and 100, and concentrations up 1 mg mL^-1. In that regime, the surfactant concentration has no effect on the exfoliation results. In the second exfoliation regime (>340 W L^-1), surfactant concentrations greater than 10 wt% produce dramatic increases in GNP yields, namely up to 3.0 mg mL^-1, and overall larger GNPs (350-500 nm) with smaller aspect ratios (5-60). We attribute these changes to the onset of a more energy intensive mechanism, termed cleavage. Cleavage involves the separation of graphite clusters in sub-bulk multi-layered graphene entities, as opposed to exfoliation, which involves the separation of individual or few-layer GNPs. Choosing an exfoliation regime by tuning simple process parameters enables control over the yield, size and morphology of the produced GNPs.

Voltage-reduced low-defect graphene oxide: a high conductivity, near-zero temperature coefficient of resistance material

A highly conductive graphene derivative was produced by using a low-defect form of graphene oxide, oxo-G, in conjunction with voltage-reduction, a simple and environmentally-benign procedure for removing oxygen-containing functional groups. A low temperature coefficient of resistance was achieved, making this material promising for temperature-stable electronics and sensors.

Formation and stability of water clusters at the molybdenum disulfide interface: a molecular dynamics simulation investigation

In this work structural properties and dynamic behavior of a water nano droplet on the molybdenum disulfide were considered. The simulation results show that water molecules form polygon clusters on the interface, and most of which are hexagonal. Structures of water clusters at the interface are seen in two forms of curved and flattened polygons, which result in the formation of hydrogen bonds between and in the adjacent layers, respectively. Most of the clusters have circular flattened structures. Calculations of the lifetime of hydrogen bonds of water molecules at the interface also show that hydrogen bonds between water molecules at the interface have a low stability. This leads to the permanent formation and breaking down of hydrogen bonds of water molecules which can cause movement of water molecules and, consequently, the displacement of the center of mass and droplet motion. Considering the changes in the center of mass of a water droplet at the MoS₂ interface display, the water droplet has a significant spontaneous motion.

Preparation and Characterization of Chiral Transition-Metal Dichalcogenide Quantum Dots and Their Enantioselective Catalysis

Two-dimensional transition-metal dichalcogenides (TMDs) had attracted enormous interests owing to their extraordinary optical, physical, and chemical properties. Herein, we prepared for the first time a series of chiral TMD quantum dots (QDs) from MoS₂ and WS₂ bulk crystals by covalent modification with chiral ligands cysteine and penicillamine. The chiral TMD QDs were carefully investigated by spectroscopic and microscopic techniques. Their chiral optical activity was confirmed by distinct circular dichroism signals different to those of the chiral ligands. Interestingly, with the assistance of copper ions, the chiral QDs displayed strong and chiral selective peroxidase-like activity. Up to now, inorganic nanomaterials with peroxidase-like activity were tremendous but seldom examples with enantioselectivity. The enantioselectivity of our chiral TMD QDs toward chiral substrates d- and l-tyrosinol was highly up to 6.77, which was almost the best performance ever reported. The mechanisms of enantioselectivity was further investigated by quartz crystal microbalance assays. We believed that because of the extraordinary electronic and optical properties, the chiral TMD QDs should be useful for nonlinear optical materials, asymmetric catalysis, chiral and biological sensors, and so on.

Oxo-Functionalized Graphene: A Versatile Precursor for Alkylated Graphene Sheets by Reductive Functionalization

Controlled covalent functionalization of graphene remains a challenging task owing to the heterogeneous nature of materials. Functionalization approaches for graphene either lack in quantifying the degree of functionalization or they do not discriminate between covalent and non-covalent functionalization. Here, graphite is oxidized and exfoliated in a three-step procedure and subsequently reduced and functionalized by hexylation. Although Raman spectroscopy is powerful to determine the degree of in-plane lattice defects (θ_LD ) and functionalization (θ_FD ), the method fails at detecting introduced hexyl groups at a concentration of about 0.03 %, next to the pre-existing in-plane lattice defects of 0.7 %. However, sensitive thermogravimetric analysis coupled with gas chromatography and mass spectrometry (TGA-GC/MS) can prove the hexylation reaction. The efficiency of functionalization is comparable to reductive functionalization of pristine chemical vapor deposition (CVD)-graphene and bulk graphite.

Enhancement of surface bioactivity on carbon fiber-reinforced polyether ether ketone via graphene modification

Background and objective

The modulus of carbon fiber-reinforced polyether ether ketone (CFR-PEEK), a composite containing layers of carbon fiber sheets, can be precisely controlled to match bone. However, CFR-PEEK is biologically inert and cannot promote bone apposition. The objective of this study was to investigate whether graphene modification could enhance the bioactivity of CFR-PEEK.

Methods and results

In vitro, the proliferation and differentiation of rat bone marrow stromal cells on scaffolds were quantified via cell-counting kit-8 assay and Western blotting analysis of osteoblast-specific proteins. Graphene modification significantly promoted bone marrow stromal cell proliferation and accelerated induced differentiation into osteogenic lineages compared to cells seeded onto nongraphene-coated CFR-PEEK. An in vivo rabbit extraarticular graft-to-bone healing model was established. At 4, 8, and 12 weeks after surgery, microcomputed tomography analyses and histological observations revealed significantly better microstructural parameters and higher average mineral apposition rates for graphene-modified CFR-PEEK implants than CFR-PEEK implants (P<0.05). van Gieson staining indicated more new bone was formed around graphene-modified CFR-PEEK implants than CFR-PEEK implants.

Conclusion

Graphene may have considerable potential to enhance the bioactivity and osseointegration of CFR-PEEK implants for clinical applications.

Flexible hemispheric microarrays of highly pressure-sensitive sensors based on breath figure method

Recently, flexible pressure sensors featuring high sensitivity, broad sensing range and real-time detection have aroused great attention owing to their crucial role in the development of artificial intelligent devices and healthcare systems. Herein, highly sensitive pressure sensors based on hemisphere-microarray flexible substrates are fabricated via inversely templating honeycomb structures deriving from a facile and static breath figure process. The interlocked and subtle microstructures greatly improve the sensing characteristics and compressibility of the as-prepared pressure sensor, endowing it a sensitivity as high as 196 kPa-1 and a wide pressure sensing range (0-100 kPa), as well as other superior performance, including a lower detection limit of 0.5 Pa, fast response time (<26 ms) and high reversibility (>10 000 cycles). Based on the outstanding sensing performance, the potential capability of our pressure sensor in capturing physiological information and recognizing speech signals has been demonstrated, indicating promising application in wearable and intelligent electronics.

DNA metallization: principles, methods, structures, and applications

This review summarizes the research activities on DNA metallization since the concept was first proposed in 1998, covering the principles, methods, structures, and applications.

Graphene-Based Nanocomposites as Promising Options for Hard Tissue Regeneration

Tissues are often damaged by physical trauma, infection or tumors. A slight injury heals naturally through the normal healing process, while severe injury causes serious health implications. Therefore, many efforts have been devoted to treat and repair various tissue defects. Recently, tissue engineering approaches have attracted a rapidly growing interest in biomedical fields to promote and enhance healing and regeneration of large-scale tissue defects. On the other hand, with the recent advances in nanoscience and nanotechnology, various nanomaterials have been suggested as novel biomaterials. Graphene, a two-dimensional atomic layer of graphite, and its derivatives have recently been found to possess promoting effects on various types of cells. In addition, their unique properties, such as outstanding mechanical and biological properties, allow them to be a promising option for hard tissue regeneration. Herein, we summarized recent research advances in graphene-based nanocomposites for hard tissue regeneration, and highlighted their promising potentials in biomedical and tissue engineering.

Bilayered BMP2 Eluting Coatings on Graphene Foam by Electrophoretic Deposition: Electroresponsive BMP2 Release and Enhancement of Osteogenic Differentiation

Recent development of three-dimensional graphene foam (GF) with conductive and interconnected macroporous structure is attracting particular attention as platforms for tissue engineering. However, widespread application of GF as bone scaffolds is restricted due to its poor mechanical property and inert surface character. To overcome these drawbacks, in this study, a bilayered biopolymer coating was designed and successfully deposited covering the entire surface area of GF skeleton. A poly(lactic-co-glycolic acid) layer was first dip-coated to strengthen the GF substrate, followed by the electrophoretic codeposition of a hybrid layer, consisting of chitosan and BMP2, to functionalize GF with the ability to recruit and induce osteogenic differentiation of hMSC. Our data indicated that the mechanical property of GF was significantly increased without compromising the macroporous structure. Importantly, the immobilized BMP2 exhibited sustained and electroresponsive release profiles with rapid response to the electric field exerted on GF, which is beneficial to balancing BMP2 dose in a physiological environment. Moreover, the osteogenic differentiation of hMSC was significantly improved on the functionalized GF. Taking advantage of the unique macrostructure from GF as well as the superior mechanical properties and BMP2 release profile supported by the deposited coatings, it is therefore expected that the developed GF could be a promising alternative as innovative bone-forming favorable scaffolds.

Multifaceted Biomedical Applications of Functional Graphene Nanomaterials to Coated Substrates, Patterned Arrays and Hybrid Scaffolds

Because of recent research advances in nanoscience and nanotechnology, there has been a growing interest in functional nanomaterials for biomedical applications, such as tissue engineering scaffolds, biosensors, bioimaging agents and drug delivery carriers. Among a great number of promising candidates, graphene and its derivatives-including graphene oxide and reduced graphene oxide-have particularly attracted plenty of attention from researchers as novel nanobiomaterials. Graphene and its derivatives, two-dimensional nanomaterials, have been found to have outstanding biocompatibility and biofunctionality as well as exceptional mechanical strength, electrical conductivity and thermal stability. Therefore, tremendous studies have been devoted to employ functional graphene nanomaterials in biomedical applications. Herein, we focus on the biological potentials of functional graphene nanomaterials and summarize some of major literature concerning the multifaceted biomedical applications of functional graphene nanomaterials to coated substrates, patterned arrays and hybrid scaffolds that have been reported in recent years.

Synthesis of Graphene-Based Sensors and Application on Detecting SF6 Decomposing Products: A Review

Graphene-based materials have aroused enormous focus on a wide range of engineering fields because of their unique structure. One of the most promising applications is gas adsorption and sensing. In electrical engineering, graphene-based sensors are also employed as detecting devices to estimate the operation status of gas insulated switchgear (GIS). This paper reviews the main synthesis methods of graphene, gas adsorption, and sensing mechanism of its based sensors, as well as their applications in detecting SF₆ decomposing products, such as SO₂, H₂S, SO₂F₂, and SOF₂, in GIS. Both theoretical and experimental researches on gas response of graphene-based sensors to these typical gases are summarized. Finally, the future research trend about graphene synthesis technique and relevant perspective are also given.

Bacterial Hyaluronidase Self-Triggered Prodrug Release for Chemo-Photothermal Synergistic Treatment of Bacterial Infection

A novel platform for targeted on-demand prodrug ascorbic acid (AA) delivery is fabricated using a bacterial hyaluronidase sensitive graphene-mesoporous silica nanosheet@hyaluronic acid-magnetic nanoparticles as the nanocarrier to treat bacterial infections. The released AA can be converted to detrimental •OH in situ on the surface of bacteria. With the chemo-photothermal synergistic effect, the designed antibacterial system can effectively inactivate bacteria and disperse stubborn biofilm.

Antibacterial applications of graphene-based nanomaterials: Recent achievements and challenges

Graphene has emerged as a novel green broad-spectrum antibacterial material, with little bacterial resistance and tolerable cytotoxic effect on mammalian cells. It exerts its antibacterial action via physical damages such as direct contact of its sharp edges with bacterial membranes and destructive extraction of lipid molecules. These damages also include wrapping and photothermal ablation mechanisms. Alternatively, chemical damage of bacteria is caused by oxidative stress with the generation of reactive oxygen species and charge transfer. Furthermore, graphene has been used as a support to disperse and stabilize various nanomaterials, such as metals, metal oxides, and polymers, with high antibacterial efficiency due to the synergistic effect. In addition, graphene-based antibiotic drug delivery platforms have been constructed. Due to the superior antibacterial properties and good biocompatibility, graphene-based nanocomposites have a wide range of applications, such as antibacterial packaging, wound dressing, and water disinfection. In this review, we highlight the antibacterial mechanism of graphene and summarize recent advances related to the antibacterial activity of graphene-based materials. Many of the recent application examples are further discussed. We hope that this review provides valuable insight, stimulates broader concerns, and spurs further developments in this promising field.

As-prepared MoS2 quantum dot as a facile fluorescent probe for long-term tracing of live cells

Recently, the newly emerged two-dimensional nanomaterials, layered transition metal dichalcogenide (e.g. MoS2) nanosheets, have drawn tremendous attentions due to their extraordinary electronic and optical properties, and MoS2 quantum dots (MoS2 QDs) with lateral sizes less than 10 nm have been found to be highly luminescent. In the present study, a facile approach for large-scale preparation of MoS2 QDs by Na intercalation reaction without using any toxic organic reagents is proposed. MoS2 QDs were carefully characterized by various techniques including transmission electron microscopy, atomic force microscopy, dynamic light scattering, spectroscopy, in vitro cytotoxicology, and capillary electrophoresis. The as-prepared MoS2 QDs were strongly fluorescent, highly photo-stable, low in cytotoxicity, and readily reactive to thiols. These inherent properties of MoS2 QDs make them excellent fluorescent probes for long-term live cell tracing. The results of live cells imaging indicated that MoS2 QD stained cells remained highly fluorescent after long-term culture, and could be easily traced from other co-cultured cell lines.

Fluorinated graphenes as advanced biosensors - effect of fluorine coverage on electron transfer properties and adsorption of biomolecules

Graphene derivatives are promising materials for the electrochemical sensing of diverse biomolecules and development of new biosensors owing to their improved electron transfer kinetics compared to pristine graphene. Here, we report complex electrochemical behavior and electrocatalytic performance of variously fluorinated graphene derivatives prepared by reaction of graphene with a nitrogen-fluorine mixture at 2 bars pressure. The fluorine content was simply controlled by varying the reaction time and temperature. The studies revealed that electron transfer kinetics and electrocatalytic activity of CFx strongly depend on the degree of fluorination. The versatility of fluorinated graphene as a biosensor platform was demonstrated by cyclic voltammetry for different biomolecules essential in physiological processes, i.e. NADH, ascorbic acid and dopamine. Importantly, the highest electrochemical performance, even higher than pristine graphene, was obtained for fluorinated graphene with the lowest fluorine content (CF0.084) due to its high conductivity and enhanced adsorption properties combining π-π stacking interaction with graphene regions with hydrogen-bonding interaction with fluorine atoms.

Investigation of the Transition from Local Anodic Oxidation to Electrical Breakdown During Nanoscale Atomic Force Microscopy Electric Lithography of Highly Oriented Pyrolytic Graphite

As one of the tip-based top-down nanoscale machining methods, atomic force microscopy (AFM) electric lithography is capable of directly generating flexible nanostructures on conductive or semi-conductive sample surfaces. In this work, distinct fabrication mechanisms and mechanism transition from local anodic oxidation (LAO) to electrical breakdown (BD) in the AFM nanoscale electric lithography of the highly oriented pyrolytic graphite sample surface was studied. We provide direct evidence of the transition process mechanism through the detected current-voltage (I-V) curve. Characteristics of the fabrication results under the LAO, transition, and BD regions involving the oxide growth rate or material removal rate and AFM probe wear are analyzed in detail. These factors are of great significance for improving the machining controllability and expanding its potential applications.

Interfacial n-Doping Using an Ultrathin TiO2 Layer for Contact Resistance Reduction in MoS2

We demonstrate a low and constant effective Schottky barrier height (ΦB ∼ 40 meV) irrespective of the metal work function by introducing an ultrathin TiO2 ALD interfacial layer between various metals (Ti, Ni, Au, and Pd) and MoS2. Transmission line method devices with and without the contact TiO2 interfacial layer on the same MoS2 flake demonstrate reduced (24×) contact resistance (RC) in the presence of TiO2. The insertion of TiO2 at the source-drain contact interface results in significant improvement in the on-current and field effect mobility (up to 10×). The reduction in RC and ΦB has been explained through interfacial doping of MoS2 and validated by first-principles calculations, which indicate metallic behavior of the TiO2-MoS2 interface. Consistent with DFT results of interfacial doping, X-ray photoelectron spectroscopy (XPS) data also exhibit a 0.5 eV shift toward higher binding energies for Mo 3d and S 2p peaks in the presence of TiO2, indicating Fermi level movement toward the conduction band (n-type doping). Ultraviolet photoelectron spectroscopy (UPS) further corroborates the interfacial doping model, as MoS2 flakes capped with ultrathin TiO2 exhibit a reduction of 0.3 eV in the effective work function. Finally, a systematic comparison of the impact of selective doping with the TiO2 layer under the source-drain metal relative to that on top of the MoS2 channel shows a larger benefit for transistor performance from the reduction in source-drain contact resistance.