Porous Hollow-Structured LaNiO3 Stabilized N,S-Codoped Graphene as an Active Electrocatalyst for Oxygen Reduction Reaction

Modification of LiMn2O4 Cathodes to Boost Kinetics Match via rGO for High-Performance Rocking-Chair Lithium-Ion Capacitors

The rocking-chair lithium-ion capacitors (RLICs), composed of a battery-type cathode and capacitive-type anode, alleviates the issue of increased internal resistance caused by electrolyte consumption during the cycling process of the lithium-ion capacitors (LICs). However, the poor conductivity of cathode materials and the mismatch between the cathode and anode are the key issues that hinder its commercial application. In this work, a modification simplification strategy is proposed to tailor the conductivity of the cathode and matching characteristic with the anode. The in situ grown lithium manganate (LMO) is featured with a three-dimensional conductive network constructed by reduced graphene oxide (rGO). The optimized LMO/rGO composite cathode demonstrates an excellent rate performance, lithium-ion diffusion rate, and cycling performance. After assembling an RLICs with activated carbon (AC), the RLICs exhibits an energy density of as high as 239.11 Wh/kg at a power density of 400 W/kg. Even at a power density of 200 kW/kg, its energy density can maintain at 39.9 Wh/kg. These excellent electrochemical performances are mainly attributed to the compounding of LMO with rGO, which not only improves the conductivity of the cathode but also realizes a better matching with the capacitive-type anode. This modification strategy provides a reference for the further development of energy storage devices suitable for actual production conditions and application scenarios.

Application of response surface methodology for optimization of the test condition of oxygen evolution reaction over La0.8Ba0.2CoO3 perovskite-active carbon composite

The Experimental Design was applied to optimize the electrocatalytic activity of La0.8Ba0.2CoO3 perovskite oxide/Active Carbon composite material in the alkaline solution for the Oxygen Evolution Reaction. After the preparation of La0.8Ba0.2CoO3, and structural characterizations, the experimental design was utilized to determine the optimal amount of the composite material and testing conditions. The overpotential was defined as the response variable, and the mass ratio of perovskite/active carbon, Potassium hydroxide (KOH) concentration, and Poly(vinylidene fluoride) (PVDF) amount were considered effective parameters. The significance of model terms is demonstrated by P-values less than 0.0500. The proposed prediction model determined the optimal amounts of 0.665 mg of PVDF, a KOH concentration of 0.609 M, and A perovskite/Active Carbon mass ratio of 2.81 with 308.22 mV overpotential (2.27% greater than the actual overpotential). The stability test of the optimized electrode material over 24 h suggests that it could be a good candidate electrocatalyst for OER with reusability potential.

High-Entropy Enhanced Microwave Attenuation in Titanate Perovskites

High-entropy oxides (HEOs), which incorporate multiple-principal cations into single-phase crystals and interact with diverse metal ions, extend the border for available compositions and unprecedented properties. Herein, a high-entropy-stabilized (Ca_0.2 Sr_0.2 Ba_0.2 La_0.2 Pb_0.2 )TiO₃  perovskite is reported, and the effective absorption bandwidth (90% absorption) improves almost two times than that of BaTiO₃ . The results demonstrate that the regulation of entropy configuration can yield significant grain boundaries, oxygen defects, and an ultradense distorted lattice. These characteristics give rise to strong interfacial and defect-induced polarizations, thus synergistically contributing to the dielectric attenuation performance. Moreover, the large strains derived from the strong lattice distortions in the high-entropy perovskite offer varied transport for electron carriers. The high-entropy-enhanced positive/negative charges accumulation around grain boundaries and strain-concentrated location, quantitatively validated by electron holography, results in unusual dielectric polarization loss. This study opens up an effective avenue for designing strong microwave absorption materials to satisfy the increasingly demanding requirements of advanced and integrated electronics. This work also offers a paradigm for improving other interesting properties for HEOs through entropy engineering.

Water electrolysis: from textbook knowledge to the latest scientific strategies and industrial developments

Replacing fossil fuels with energy sources and carriers that are sustainable, environmentally benign, and affordable is amongst the most pressing challenges for future socio-economic development. To that goal, hydrogen is presumed to be the most promising energy carrier. Electrocatalytic water splitting, if driven by green electricity, would provide hydrogen with minimal CO2 footprint. The viability of water electrolysis still hinges on the availability of durable earth-abundant electrocatalyst materials and the overall process efficiency. This review spans from the fundamentals of electrocatalytically initiated water splitting to the very latest scientific findings from university and institutional research, also covering specifications and special features of the current industrial processes and those processes currently being tested in large-scale applications. Recently developed strategies are described for the optimisation and discovery of active and durable materials for electrodes that ever-increasingly harness first-principles calculations and machine learning. In addition, a technoeconomic analysis of water electrolysis is included that allows an assessment of the extent to which a large-scale implementation of water splitting can help to combat climate change. This review article is intended to cross-pollinate and strengthen efforts from fundamental understanding to technical implementation and to improve the 'junctions' between the field's physical chemists, materials scientists and engineers, as well as stimulate much-needed exchange among these groups on challenges encountered in the different domains.

Coupling LaNiO3 Nanorods with FeOOH Nanosheets for Oxygen Evolution Reaction

Perovskite-based electrocatalysts with compositional flexibility and tunable electronic structures have emerged as one of the promising non-noble metal candidates for oxygen evolution reaction (OER). Here, we propose a heterostructure comprising perovskite oxide (LaNiO3) nanorods and iron oxide hydroxide (FeOOH) nanosheets as an effective electrochemical catalyst for OER. The optimized 0.25Fe-LNO catalyst with an interesting 1D-2D hierarchical structure shows a low overpotential of 284 mV at 10 mA cm−2 and a small Tafel slope of 69 mV dec−1. The enhanced performance can be explained by the synergistic effect between LaNiO3 and FeOOH, resulting in an improved electrochemically active surface area, facilitated charge transfer and the optimized adsorption of OH intermediates.

Entropy Enhanced Perovskite Oxide Ceramic for Efficient Electrochemical Reduction of Oxygen to Hydrogen Peroxide

The electrochemical oxygen reduction reaction (ORR) offers a most promising and efficient route to produce hydrogen peroxide (H2 O2 ), yet the lack of cost-effective and high-performance electrocatalysts have restricted its practical application. Herein, an entropy-enhancement strategy has been employed to enable the low-cost perovskite oxide to effectively catalyze the electrosynthesis of H2 O2 . The optimized Pb(NiWMnNbZrTi)1/6 O3 ceramic is available on a kilogram-scale and displays commendable ORR activity in alkaline media with high selectivity over 91 % across the wide potential range for H2 O2 including an outstanding degradation property for organic dyes through the Fenton process. The exceptional performance of this perovskite oxide is attributed to the entropy stabilization-induced polymorphic transformation assuring the robust structural stability, decreased charge mobility as well as synergistic catalytic effects which we confirm using advanced in situ Raman, transient photovoltage, Rietveld refinement as well as finite elemental analysis.

Synergistic effect between La–Ni bimetallic oxides for the efficient decomposition of hydrogen peroxide

La–Ni bimetallic oxides with pure composition and well-crystalline structures were prepared, which showed high catalytic activities toward H₂O₂ decomposition.

The high photocatalytic efficiency and stability of LaNiO3/g-C3N4 heterojunction nanocomposites for photocatalytic water splitting to hydrogen

A binary direct Z-scheme LaNiO₃/g-C₃N₄ nanocomposite photocatalyst consisted with LaNiO₃ nanoparticles and g-C₃N₄ nanosheets was successfully synthesized by means of mechanical mixing and solvothermal methods in order to improve the photocatalytic water splitting activity. The as-prepared materials were characterized by powder X-ray diffraction (XRD), Scanning Electron microscope (SEM), Transmission Electron microscope (TEM), X-ray photoelectron spectroscope (XPS), Fourier Transform Infrared Spectroscopy (FT-IR) and N₂ adsorption–desorption experiments, respectively, demonstrating the formation of interfacial interaction and heterogeneous structure in LaNiO₃/g-C₃N₄ nanocomposites. Under UV-light irradiation, the LaNiO₃/g-C₃N₄ samples which without the addition of any noble metal as co-catalyst behaved enhanced photocatalytic water splitting activity compared with pure LaNiO₃ and g-C₃N₄, owing to the Z-scheme charge carrier transfer pathway. Especially, the LaNiO₃/70%g-C₃N₄ nanocomposite reach an optimal yield of up to 3392.50 µmol g⁻¹ in 5 h and held a maximum H₂ evolution rate of 678.5 µmol h⁻¹ g⁻¹ that was 5 times higher than that of pure LaNiO₃.

Cation and Anion Co-doped Perovskite Nanofibers for Highly Efficient Electrocatalytic Oxygen Evolution

Perovskite oxides have been recognized as one of the most attractive oxygen evolution reaction (OER) catalysts because of their low cost, earth abundance, and robust nature. Herein, one-dimensional porous LaFe_1-xNi_xO₃ (LFNO) perovskite oxide nanofibers (LFNO NFs) are fabricated with a feasible electrospinning route and its further post-calcination treatment. By tailoring the atomic percent of Fe and Ni in the perovskite oxide, we determined that LaFe_0.25Ni_0.75O₃ (LFNO-III) NFs afford the best OER activity among all the prepared perovskite oxides. Especially remarkable is that the further selenide-doped LaFe_0.25Ni_0.75O₃ (LFNOSe-III) NFs exhibit outstanding OER activity with a low overpotential of 287 mV at 10 mA cm^-2 and a small Tafel slope of 87 mV dec^-1 in 1 M KOH solution, markedly exceeding that of the parent perovskite oxide and the commercial RuO₂. It also delivers decent durability with no significant degradation after 22 h of stability test. In the meanwhile, density functional theory calculations are also conducted to justify the optimized adsorption features of *OH, *O, and *OOH intermediates and unveil that the electrocatalytic active sites are the Ni atoms adjacent to Fe in the Ni- and Se codoped perovskite. This work provides an effective method for the development of highly efficient perovskite oxide catalysts.

Subnano Amorphous Fe-Based Clusters with High Mass Activity for Efficient Electrocatalytic Oxygen Reduction Reaction

The development of cost-effective and efficient oxygen-relative electrocatalysts with high mass activity is extremely critical for modern sustainable fuel cells. Here, we present a new type of subnano amorphous transition-metal clusters supported on a hierarchical carbon framework as a promising oxygen reduction reaction (ORR) electrocatalyst, synthesized by a novel "amino-induced spatial confinement" strategy. This developed Fe subnano-cluster/3D-C could deliver outstanding ORR performance with a large mass activity of ∼8600 A g_Fe^-1 at a half-wave potential of 0.92 V, ∼10 times that of the benchmarking Pt/C electrocatalyst. The atomic characterizations and theoretical calculations jointly reveal the robust surface-covalent Fe-N bonds, and the synergistic effect of hetero Fe^2+/0 species is essentially beneficial for the adsorption of *O₂ and the formation of key *O intermediate during the ORR process, contributing to high oxygen-relative electrocatalytic activity for subnano amorphous Fe clusters.

Facile synthesis of N-doped graphene supported porous cobalt molybdenum oxynitride nanodendrites for the oxygen reduction reaction

Exploring an inexpensive, active and stable electrocatalyst as an alternative to expensive Pt for the oxygen reduction reaction (ORR), porous Co-Mo-ON alloy nanodendrites supported on nitrogen-doped graphene (Co-Mo-ON/NG) have been synthesized by a two-step solid state heating method. The Co-Mo-ON/NG nanodendrites offer high ORR activity and superior electrochemical stability both in acidic and alkaline media. This superiority is due to the synergistic effect of NG, enhanced catalytic efficiency by Mo, highly active intrinsic surface area and exposure of catalytic facets of nanodendritic morphology towards the ORR. The Co-Mo-ON/NG nanodendrites show a 4e- ORR process with 0.710 V and 0.915 V onset potentials in 0.5 M H2SO4 and 0.1 M KOH, respectively. The Co-Mo-ON/NG nanodendrites show extreme electrochemical stability in terms of 96% and 97% current retention for 40 000 s in both acidic and alkaline media, respectively, long term durability for continuous 2000 cycles and greater resistance to methanol than the commercial Pt/C catalyst. Furthermore, Mo-ON/NG, Co-ON/NG, and Co-Mo-ON are also tested to evaluate the effect of Mo-doping and NG on the electrocatalytic activity of Co-Mo-ON/NG nanodendrites. Owing to their low cost, easy synthesis, outstanding ORR performance, and extreme durability, Co-Mo-ON/NG nanodendrites emerged as a promising non-precious and highly stable ORR electrocatalyst in fuel cell applications.

The design of hollow PdO–Co3O4 nano-dodecahedrons with moderate catalytic activity for Li–O2 batteries

Hollow PdO–Co₃O₄ nano-dodecahedrons can stably cycle for more than 90 cycles with a low overpotential as an electrocatalyst for Li–O₂ batteries.

Hierarchical Heterostructures of Ultrasmall Fe2O3-Encapsulated MoS2/N-Graphene as an Effective Catalyst for Oxygen Reduction Reaction

In this study, a facile approach has been successfully applied to synthesize a hierarchical three-dimensional architecture of ultrasmall hematite nanoparticles homogeneously encapsulated in MoS₂/nitrogen-doped graphene nanosheets, as a novel non-Pt cathodic catalyst for oxygen reduction reaction in fuel cell applications. The intrinsic topological characteristics along with unique physicochemical properties allowed this catalyst to facilitate oxygen adsorption and sped up the reduction kinetics through fast heterogeneous decomposition of oxygen to final products. As a result, the catalyst exhibited outstanding catalytic performance with a high electron-transfer number of 3.91-3.96, which was comparable to that of the Pt/C product. Furthermore, its working stability with a retention of 96.1% after 30 000 s and excellent alcohol tolerance were found to be significantly better than those for the Pt/C product. This hybrid can be considered as a highly potential non-Pt catalyst for practical oxygen reduction reaction application in requirement of low cost, facile production, high catalytic behavior, and excellent stability.

Highly Active and Durable Core-Shell fct-PdFe@Pd Nanoparticles Encapsulated NG as an Efficient Catalyst for Oxygen Reduction Reaction

Development of highly active and durable catalysts for oxygen reduction reaction (ORR) alternative to Pt-based catalyst is an essential topic of interest in the research community but a challenging task. Here, we have developed a new type of face-centered tetragonal (fct) PdFe-alloy nanoparticle-encapsulated Pd (fct-PdFe@Pd) anchored onto nitrogen-doped graphene (NG). This core-shell fct-PdFe@Pd@NG hybrid is fabricated by a facile and cost-effective technique. The effect of temperature on the transformation of face-centered cubic (fcc) to fct structure and their effect on ORR activity are systematically investigated. The core-shell fct-PdFe@Pd@NG hybrid exerts high synergistic interaction between fct-PdFe@Pd NPs and NG shell, beneficial to enhance the catalytic ORR activity and excellent durability. Impressively, core-shell fct-PdFe@Pd@NG hybrid exhibits an excellent catalytic activity for ORR with an onset potential of ∼0.97 V and a half-wave potential of ∼0.83 V versus relative hydrogen electrode, ultrahigh current density, and decent durability after 10 000 potential cycles, which is significantly higher than that of marketable Pt/C catalyst. Furthermore, the core-shell fct-PdFe@Pd@NG hybrid also shows excellent tolerance to methanol, unlike the commercial Pt/C catalyst. Thus, these findings open a new protocol for fabricating another core-shell hybrid by facile and cost-effective techniques, emphasizing great prospect in next-generation energy conversion and storage applications.

CuAg@Ag Core-Shell Nanostructure Encapsulated by N-Doped Graphene as a High-Performance Catalyst for Oxygen Reduction Reaction

Development of a robust, cost-effective, and efficient catalyst is extremely necessary for oxygen reduction reaction (ORR) in fuel cell applications. Herein, we reported a well-defined nanostructured catalyst of highly dispersed CuAg@Ag core-shell nanoparticle (NP)-encapsulated nitrogen-doped graphene nanosheets (CuAg@Ag/N-GNS) exhibiting a superior catalytic activity toward ORR in alkaline medium. The synergistic effects produced from the unique properties of CuAg@Ag core-shell NPs and N-GNS made such a novel nanohybrid display a catalytic behavior comparable to that of the commercial Pt/C product. In particular, it demonstrated a much better stability and methanol tolerance than Pt/C under the same conditions. Because of its outstanding electrochemical performance and ease of synthesis, CuAg@Ag/N-GNS material was expected to be a promising low-cost catalyst for ORR in alkaline fuel cell applications.

Melamine formaldehyde–metal organic gel interpenetrating polymer network derived intrinsic Fe–N-doped porous graphitic carbon electrocatalysts for oxygen reduction reaction

Melamine formaldehyde metal organic gel interpenetrating networks for heteroporous Fe–N-doped carbon.