Coagulation of Quartz Particles in Aqueous Solutions of Copper(II)

Isoelectric points and points of zero charge of metal (hydr)oxides: 50years after Parks' review

The pH-dependent surface charging of metal (hydr)oxides is reviewed on the occasion of the 50th anniversary of the publication by G.A. Parks: "Isoelectric points of solid oxides, solid hydroxides, and aqueous hydroxo complex systems" in Chemical Reviews. The point of zero charge (PZC) and isoelectric point (IEP) became standard parameters to characterize metal oxides in aqueous dispersions, and they define adsorption (surface excess) of ions, stability against coagulation, rheological properties of dispersions, etc. They are commonly used in many branches of science including mineral processing, soil science, materials science, geochemistry, environmental engineering, and corrosion science. Parks established standard procedures and experimental conditions which are required to obtain reliable and reproducible values of PZC and IEP. The field is very active, and the number of related papers exceeds 300 a year, and the standards established by Parks remain still valid. Relevant experimental techniques improved over the years, especially the measurements of electrophoretic mobility became easier and more reliable, are the numerical values of PZC and IEP compiled by Parks were confirmed by contemporary publications with a few exceptions. The present paper is an up-to-date compilation of the values of PZC and IEP of metal oxides. Unlike in former reviews by the same author, which were more comprehensive, only limited number of selected results are presented and discussed here. On top of the results obtained by means of classical methods (titration and electrokinetic methods), new methods and correlations found over the recent 50years are presented.

AFM Measurements of Adhesion between CMP Slurry Particles and Copper

Adhesion between abrasive particles and surfaces being polished plays an important role in chemical mechanical planarization (CMP) processes. The changes in particle - surface and particle – particle interactions can significantly influence the effectiveness of material removal and cleaning methods. To determine the adhesion between actual abrasive particles and different surfaces treated by the CMP process a method employing atomic force microscopy (AFM) technique is being developed.

The monolayer of silica abrasive nanoparticles was deposited on silicon wafer covered with polymer anchoring layer. High affinity of the thin polymer film to the particles and wafer ensures the stability of particles monolayer on the surface during measurements. AFM cantilever was modified with attachment of 20-40 microns hollow glass bead (representing a flat surface), which then was covered with copper using physical vapor deposition technique. Force-distance curves were collected employing AFM force volume mode and used to calculate the adhesion value. The effect of different factors (such as pH, presence of surfactants) on adhesion between copper surface and silica slurry has been studied.

Application of ferrate(VI) in the treatment of industrial wastes containing metal-complexed cyanides : a green treatment

Ferrate(VI) was employed for the oxidation of cyanide (CN) and simultaneous removal of copper or nickel in the mixed/complexed systems of CN-Cu, CN-Ni, or CN-Cu-Ni. The degradation of CN (1.00 mmol/L) and removal of Cu (0.095 mmol/L) were investigated as a function of Fe(VI) doses from 0.3-2.00 mmol/L at pH 10.0. It was found that Fe(VI) could readily oxidize CN and the reduction of Fe(VI) into Fe(III) might serve efficiently for the removal of free copper ions. The increase in Fe(VI) dose apparently favoured the CN oxidation as well as Cu removal. Moreover, the pH dependence study (pH 10.0-13.0) revealed that the oxidation of CN was almost unaffected in the studied pH range (10.0-13.0), however, the maximum removal efficiency of Cu was obtained at pH 13.0. Similarly, treatment was carried out for CN-Ni system having the initial Ni concentration of 0.170 mmol/L and CN concentration of 1.00 mmol with Fe(VI) dose 2.00 mmol at various pH values (10.0-12.0). Results showed a partial oxidation of CN and partial removal of Ni. It can be observed that Fe(VI) can partially degrade the CN-Ni complex in this pH range. Further, Fe(VI) was applied for the treatment of simulated industrial waste/effluent waters treatment containing CN, Cu, and Ni.

Influence of hydrolyzable metal ions on the interfacial chemistry, particle interactions, and dewatering behavior of kaolinite dispersions

The influence of hydrolyzable metal ions (Mn(II) and Ca(II)) adsorption on the surface chemistry, particle interactions, flocculation, and dewatering behavior of kaolinite dispersions has been investigated at pH 7.5 and 10.5. Metal ion adsorption was strongly cation type- and pH-dependent and significantly influenced the zeta potential, anionic polyacrylamide-acrylate flocculant (PAM) adsorption, shear yield stress, settling rate, and consolidation of kaolinite slurries. The presence of Mn(II) and Ca(II) ions alone led to a systematic reduction in zeta potential due to specific adsorption of positively charged metal ion-based hydrolysis products at the kaolinite-water interface. Metal ion-mediated zeta potential changes were reflected by lower dispersion shear yield stresses and improved clarification (higher settling rates) but had no detectable effect on dispersion consolidation. The adsorption of PAM was significantly improved by prior addition of the metal ions. In the presence of Mn(II) or Ca(II) ions, the flocculant adsorption density was enhanced at pH 7.5 for Mn(II) and pH 10.5 for Ca(II). Optimum flocculation conditions, involving partial rather than complete particle surface coverage by both metal ions and flocculant, were identified. As a consequence, the metal ions and flocculant acted synergistically to enhance dewatering, producing particle interactions that were more conducive to high settling rates and greater consolidation of kaolinite dispersions at pH 7.5 than 10.5.

Multiinstrument Study of the Electrophoretic Mobility of Quartz

The electrophoretic mobility of quartz in 0.01 mol dm(-3) NaCl and NaNO3 over the pH range 2-8 was studied using five different commercial instruments. The mobilities over the pH range 4-8 were relatively consistent, but the mobilities over the pH range 2-4 and the position of the isoelectric point IEP varied from one instrument to another. This result suggests that the discrepancies in the apparent IEP of quartz (and other silicas) reported in the literature are due to the instrument artifacts.