Monitoring biomolecular interactions by time-lapse atomic force microscopy

Nanoscale probing of local dielectric changes at the interface between solids and aqueous saline solutions

The mobility of dissolved ions and charged molecules at interfaces underpins countless processes in science and technology. Experimentally, this is typically measured from the averaged response of the charges to an electrical potential. High-resolution Atomic Force Microscopy (AFM) can image single adsorbed ions and molecules at solid-liquid interfaces, but probing the associated dynamics remains highly challenging. One possible strategy is to investigate the response of the species of interest to a highly localized AC electric field in an approach analogous to dielectric spectroscopy. The dielectric force experienced by the AFM tip apex is modulated by the dielectric properties of the sample probed, itself sensitive to the mobilities of solvated charges and dipoles. Previous work successfully used this approach to quantify the dielectric constant of thin samples, but with limited spatial resolution. Here we propose a strategy to simultaneously map the nanoscale topography and local dielectric variations across a range of interfaces by conducting high-resolution AFM imaging concomitantly with electrical AC measurements in a multifrequency approach. The strategy is tested over a 500 MHz bandwidth in pure liquids with different dielectric constants and in saline aqueous solutions. In liquids with higher dielectric constants, the system behaves as inductive-resistive-capacitive but the adjunction of ions removes the inductive resonances and precludes measurements at higher frequencies. High-resolution imaging is demonstrated over single graphene oxide (GrO) flakes with simultaneous but decoupled dielectric measurements. The dielectric constant is consistent and reproducible across liquids, except at higher salt concentrations where frequency-dependent effects occur. The results suggest the strategy is suitable for nanometre-level mapping of the dielectric properties of solid-liquid interfaces, but more work is needed to fully understand the different physical effects underpinning the measurements.

Atomic Force Microscopy for Protein Detection and Their Physicoсhemical Characterization

This review is focused on the atomic force microscopy (AFM) capabilities to study the properties of protein biomolecules and to detect the proteins in solution. The possibilities of application of a wide range of measuring techniques and modes for visualization of proteins, determination of their stoichiometric characteristics and physicochemical properties, are analyzed. Particular attention is paid to the use of AFM as a molecular detector for detection of proteins in solutions at low concentrations, and also for determination of functional properties of single biomolecules, including the activity of individual molecules of enzymes. Prospects for the development of AFM in combination with other methods for studying biomacromolecules are discussed.

Modeling of the mechano-chemical behaviour of the nuclear pore complex: current research and perspectives

Recent evidence suggests that mechanical deformation of the cell nucleus regulates the nuclear import of the transcriptional activators of genes involved in primary physiological cell responses such as stem cell differentiation. In addition, this nuclear mechanosensing response is de-regulated in pathological states, such as cancer and neurodegeneration. One hypothesis that could greatly advance the field is that the deformation of the nuclear envelope activates nuclear pore complexes through a direct mechanical link. The understanding of this possible mechanism for nuclear pore complex stretch-activation entails studying the mechanical connection of this complex to the nuclear envelope at the nanoscale. The nanomechanics of the nuclear pore complex is thus emerging as a novel research field, bridging nanoscience with nanotechnology. This review examines the frontier of research methodologies that are potentially useful for building a computational model of this interaction. This includes, for example, electron tomography to assess the geometrical features of the nuclear pore complex and nanoindentation to estimate its mechanical properties and that of the nuclear envelope. In order to summarize the state-of-the-art and perspectives in the field of NPC nanomechanics, this review covers highly interdisciplinary experimental and theoretical research methodologies pertaining to the fields of physics, chemistry, biology, materials and mechanics.

Introduction to Atomic Force Microscopy (AFM) in Biology

The atomic force microscope (AFM) has the unique capability of imaging biological samples with molecular resolution in buffer solution over a wide range of time scales from milliseconds to hours. In addition to providing topographical images of surfaces with nanometer- to angstrom-scale resolution, forces between single molecules and mechanical properties of biological samples can be investigated from the nano-scale to the micro-scale. Importantly, the measurements are made in buffer solutions, allowing biological samples to "stay alive" within a physiological-like environment while temporal changes in structure are measured-e.g., before and after addition of chemical reagents. These qualities distinguish AFM from conventional imaging techniques of comparable resolution, e.g., electron microscopy (EM). This unit provides an introduction to AFM on biological systems and describes specific examples of AFM on proteins, cells, and tissues. The physical principles of the technique and methodological aspects of its practical use and applications are also described. © 2016 by John Wiley & Sons, Inc.

Integrated compositional and nanomechanical analysis of a polyurethane surface modified with a fluorous oxetane siliceous-network hybrid

Investigating the surface characteristics of heterogeneous polymer systems is important for understanding how to better tailor surfaces and engineering specific reactions and desirable properties. Here we report on the surface properties for a blend consisting of a major component, a linear polyurethane or thermoplastic elastomer (TPU), and a minor component that is a hybrid network. The hybrid network consists of a fluorous polyoxetane soft block and a hydrolysis/condensation inorganic (HyCoin) network. Phase separation during coating formation results in surface concentration of the minor fluorous hybrid domain. The TPU is H12MDI/BD(50)-PTMO-1000 derived from bis(cyclohexylmethylene)-diisocyanate and butane diol (50 wt %) and poly(tetramethylene oxide). Surface modification results from a novel network-forming hybrid composed of poly(trifluoroethoxymethyl-methyl oxetane) diol) (3F) as the fluorous moiety end-capped with 3-isocyanatopropylriethoxysilane and bis(triethoxysilyl)ethane (BTESE) as a siliceous stabilizer. We use an integrated approach that combines elemental analysis of the near surface via X-ray photoelectron microscopy with surface mapping using atomic force microscopy that presents topographical and phase imaging along with nanomechanical properties. Overall, this versatile, high-resolution approach enabled unique insight into surface composition and morphology that led to a model of heterogeneous surfaces containing a range of constituents and properties.

A tetrahedral transition state at the active sites of the 20S proteasome is coupled to opening of the alpha-ring channel

Intrinsic conformational transitions contribute to the catalytic action of many enzymes. Here we use a single-molecule approach to demonstrate how such transitions are linked to the catalytic sites of the eukaryotic proteasome, an essential protease of the ubiquitin pathway. The active sites of the cylindrical proteasomal core particle are located in a central chamber accessible through gated entry channels. By using atomic force microscopy, we found continual alternation between open and closed gate conformations. We analyzed the relative abundance of these conformers in wild-type and mutated yeast core particles upon exposure to substrates or inhibitors. Our data indicate that the dynamic gate can be opened by allosteric coupling to a tetrahedral transition state at any of the working active centers. The results point to the N(alpha)-amine of the N-terminal active site threonyl residue as the major effector group responsible for triggering the essential conformational switch.

Introduction to atomic force microscopy (AFM) in biology

The atomic force microscope has the unique capability of imaging biological samples with molecular resolution in buffer solution. In addition to providing topographical images of surfaces with nanometer- to angstrom-scale resolution, forces between single molecules and mechanical properties of biological samples can be investigated. Importantly, the measurements are made in buffer solutions, allowing biological samples to stay alive within a physiological-like environment while temporal changes in structure are measured. This overview provides an introduction to AFM on biological systems and describes specific examples of AFM on proteins. The physical principles of the technique and methodological aspects of its practical use and applications are also described.

Past, present and future of atomic force microscopy in life sciences and medicine

To introduce this special issue of the Journal of Molecular Recognition dedicated to the applications of atomic force microscopy (AFM) in life sciences, this paper presents a short summary of the history of AFM in biology. Based on contributions from the first international conference of AFM in biological sciences and medicine (AFM BioMed Barcelona, 19-21 April 2007), we present and discuss recent progress made using AFM for studying cells and cellular interactions, probing single molecules, imaging biosurfaces at high resolution and investigating model membranes and their interactions. Future prospects in these different fields are also highlighted.

PrP106–126 amide causes the semi-penetrated poration in the supported lipid bilayers

A major hallmark of prion diseases is the cerebral amyloid accumulation of the pathogenic PrP(Sc), an abnormally misfolded, protease-resistant, and beta-sheet rich protein. PrP106-126 is the key domain responsible for the conformational conversion and aggregation of PrP. It shares important physicochemical characteristics with PrP(Sc) and presents similar neurotoxicity as PrP(Sc). By combination of fluorescence polarization, dye release assay and in situ time-lapse atomic force microscopy (AFM), we investigated the PrP106-126 amide interacting with the large unilamellar vesicles (LUVs) and the supported lipid bilayers (SLBs). The results suggest that the interactions involve a poration-mediated process: firstly, the peptide binding results in the formation of pores in the membranes, which penetrate only half of the membranes; subsequently, PrP106-126 amide undergoes the poration-mediated diffusion in the SLBs, represented by the formation and expansion of the flat high-rise domains (FHDs). The possible mechanisms of the interactions between PrP106-126 amide and lipid membranes are proposed based on our observations.

Developing scanning probe–based nanodevices—stepping out of the laboratory into the clinic

This report focuses on nanotools based on the scanning force microscope (SFM) for imaging, measuring, and manipulating biological matter at the sub-micron scale. Because pathophysiological processes often occur at the (sub-) cellular scale, the SFM has opened the exciting possibility to spot diseases at a stage before they become symptomatic and cause functional impairments in the affected part of the body. Such presymptomatic detection will be key to developing effective therapies to slow or halt disease progression.

Lipid-induced beta-amyloid peptide assemblage fragmentation

Alzheimer's disease is the most common cause of dementia and is widely believed to be due to the accumulation of beta-amyloid peptides (Abeta) and their interaction with the cell membrane. Abetas are hydrophobic peptides derived from the amyloid precursor proteins by proteolytic cleavage. After cleavage, these peptides are involved in a self-assembly-triggered conformational change. They are transformed into structures that bind to the cell membrane, causing cellular degeneration. However, it is not clear how these peptide assemblages disrupt the structural and functional integrity of the membrane. Membrane fluidity is one of the important parameters involved in pathophysiology of disease-affected cells. Probing the Abeta aggregate-lipid interactions will help us understand these processes with structural detail. Here we show that a fluid lipid monolayer develop immobile domains upon interaction with Abeta aggregates. Atomic force microscopy and transmission electron microscopy data indicate that peptide fibrils are fragmented into smaller nano-assemblages when interacting with the membrane lipids. Our findings could initiate reappraisal of the interactions between lipid assemblages and Abeta aggregates involved in Alzheimer's disease.

From the trap to the basket: getting to the bottom of the nuclear pore complex

Nuclear pore complexes (NPCs) are large supramolecular assemblies that perforate the double-membraned nuclear envelope and serve as the sole gateways of molecular exchange between the cytoplasm and the nucleus in interphase cells. Combining novel specimen preparation regimes with innovative use of high-resolution scanning electron microscopy, Hans Ris produced in the late eighties stereo images of the NPC with unparalleled clarity and structural detail, thereby setting new standards in the field. Since that time, efforts undertaken to resolve the molecular structure and architecture, and the numerous interactions that occur between NPC proteins (nucleoporins), soluble transport receptors, and the small GTPase Ran, have led to a deeper understanding of the functional role of NPCs in nucleocytoplasmic transport. In spite of these breakthroughs, getting to the bottom of the actual cargo translocation mechanism through the NPC remains elusive and controversial. Here, we review recent insights into NPC function by correlating structural findings with biochemical data. By introducing new experimental and computational results, we reexamine how NPCs can discriminate between receptor-mediated and passive cargo to promote vectorial translocation in a highly regulated manner. Moreover, we comment on the importance and potential benefits of identifying and experimenting with individual key components implicated in the translocation mechanism. We conclude by dwelling on questions that we feel are pertinent to a more rational understanding of the physical aspects governing NPC mechanics. Last but not least, we substantiate these uncertainties by boldly suggesting a new direction in NPC research as a means to verify such novel concepts, for example, a de novo designed 'minimalist' NPC.

From the Polymorphism of Amyloid Fibrils to their Assembly Mechanism and Cytotoxicity

Extracellular amyloid deposits are present in a variety of diseases. They contain amyloid fibrils that arise from the association of proteins or peptides. At the molecular level, all these fibrils share a common assembly principle based on a conformational change of the protein precursor leading to the formation of a cross-beta sheet structure. The smallest observed fibrils in vitro, often called protofibrils, are 4-5 nm in diameter. An amyloid fibril is generally composed of several of these protofibrils and may adopt different morphologies such as ribbons, sheets, or multistranded cables. This polymorphism was observed with many different amyloid-forming peptides and proteins using electron microscopy. The need to understand the molecular origin of this effect as well as the desire to find inhibitors of fibril formation has driven researchers toward the dissection of amyloid fibril assembly pathways. We review the current knowledge on amyloid polymorphism and discuss recent findings in the field concerning amyloid fibril assembly pathways and cytotoxicity mechanisms.

Investigating native coronary artery endothelium in situ and in cell culture by scanning force microscopy

The purpose of our studies is to better understand the morphology and functioning of the arteries and their changes in pathogenesis. The most frequently used imaging techniques are intravascular ultrasound, magnetic resonance imaging, and optical coherence tomography. These methods do not image cell-level structural details and only provide biomechanical properties indirectly. We present a new protocol for imaging the endothelial surface and measuring elastic properties of vascular tissue by scanning force microscopy. Full-thickness sections of native pig coronary arteries were prepared. In addition, cultured human umbilical vein endothelial cells were studied as an in vitro model system and for comparison. We encountered a variety of difficulties mostly due to the softness of vascular tissue which required significant adaptations of standard equipment: (i) a new specimen holder designed to stably immobilize the coronary arteries; (ii) a phase-contrast microscope incorporated for assessing the status of the cultured endothelial cells and positioning the scanning force microscope (SFM) tip at a site of interest; and (iii) a continuous exchange of the culture medium at 37 degrees C to assure viability of the cells in the SFM over extended times. We were thus able to investigate both fresh arterial tissue and living endothelial cells in a near-physiological environment. We present initial SFM images of vascular tissue at a spatial resolution similar to scanning electron microscopy, but which also provide a closer view of the bona fide structure of native tissue. Novel morphological features such as distinct granular particles were observed. Moreover, we report initial measurements of vascular tissue surface stiffness, obtained by indentation-type SFM.

Architecture and high-resolution structure of Bacillus thuringiensis and Bacillus cereus spore coat surfaces

We have utilized atomic force microscopy (AFM) to visualize the native surface topography and ultrastructure of Bacillus thuringiensis and Bacillus cereus spores in water and in air. AFM was able to resolve the nanostructure of the exosporium and three distinctive classes of appendages. Removal of the exosporium exposed either a hexagonal honeycomb layer (B. thuringiensis) or a rodlet outer spore coat layer (B. cereus). Removal of the rodlet structure from B. cereus spores revealed an underlying honeycomb layer similar to that observed with B. thuringiensis spores. The periodicity of the rodlet structure on the outer spore coat of B. cereus was approximately 8 nm, and the length of the rodlets was limited to the cross-patched domain structure of this layer to approximately 200 nm. The lattice constant of the honeycomb structures was approximately 9 nm for both B. cereus and B. thuringiensis spores. Both honeycomb structures were composed of multiple, disoriented domains with distinct boundaries. Our results demonstrate that variations in storage and preparation procedures result in architectural changes in individual spore surfaces, which establish AFM as a useful tool for evaluation of preparation and processing "fingerprints" of bacterial spores. These results establish that high-resolution AFM has the capacity to reveal species-specific assembly and nanometer scale structure of spore surfaces. These species-specific spore surface structural variations are correlated with sequence divergences in a spore core structural protein SspE.

The high-resolution architecture and structural dynamics of Bacillus spores

The capability to image single microbial cell surfaces at nanometer scale under native conditions would profoundly impact mechanistic and structural studies of pathogenesis, immunobiology, environmental resistance, and biotransformation. Here, using in vitro atomic force microscopy, we have directly visualized high-resolution native structures of bacterial endospores, including the exosporium and spore coats of four Bacillus species in air and water environments. Our results demonstrate that the mechanisms of spore coat self-assembly are similar to those described for inorganic and macromolecular crystallization. The dimensions of individual Bacillus atrophaeus spores decrease reversibly by 12% in response to a change in the environment from fully hydrated to air-dried state, establishing that the dormant spore is a dynamic physical structure. The interspecies distributions of spore length and width were determined for four species of Bacillus spores in water and air environments. The dimensions of individual spores differ significantly depending upon species, growth regimes, and environmental conditions. These findings may be useful in the reconstruction of environmental and physiological conditions during spore formation and for modeling the inhalation and dispersal of spores. This study provides a direct insight into molecular architecture and structural variability of bacterial endospores as a function of spatial and developmental organizational scales.

Physical properties of Escherichia coli P pili measured by optical tweezers

The mechanical behavior of individual P pili of uropathogenic Escherichia coli has been investigated using optical tweezers. P pili, whose main part constitutes the PapA rod, composed of approximately 10(3) PapA subunits in a helical arrangement, are distributed over the bacterial surface and mediate adhesion to host cells. They are particularly important in the pathogenesis of E. coli colonizing the upper urinary tract and kidneys. A biological model system has been established for in situ measurements of the forces that occur during mechanical stretching of pili. A mathematical model of the force-versus-elongation behavior of an individual pilus has been developed. Three elongation regions of pili were identified. In region I, P pili stretch elastically, up to a relative elongation of 16 +/- 3%. The product of elasticity modulus and area of a P pilus, EA, was assessed to 154 +/- 20 pN (n=6). In region II, the quaternary structure of the PapA rod unfolds under a constant force of 27 +/- 2 pN (n approximately 100) by a sequential breaking of the interactions between adjacent layers of PapA subunits. This unfolding can elongate the pilus up to 7 +/- 2 times. In region III, pili elongate in a nonlinear manner as a result of stretching until the bond ruptures.

Morphological analysis of glutaraldehyde-fixed vimentin intermediate filaments and assembly-intermediates by atomic force microscopy

Atomic force microscopy (AFM) was used to study the morphology of vimentin intermediate filaments (IFs) and their assembly intermediates. At each time after initiation of IF assembly in vitro of recombinant mouse vimentin, the sample was fixed with 0.1% glutaraldehyde and then applied to AFM analysis. When mature vimentin IFs were imaged in air on mica, they appeared to have a width of approximately 28 nm, a height of approximately 4 nm and a length of several micrometers. Taking into account the probe tip's distortion effect, the exact width was evaluated to be approximately 25 nm, suggesting that the filaments flatten on the substrate rather than be cylindrical with a diameter of approximately 10 nm. Vimentin IFs in air clearly demonstrated approximately 21-nm repeating patterns along the filament axis. The three-dimensional profiles of vimentin IFs indicated that the characteristic patterns were presented by repeating segments with a convex surface. The repeating patterns close to 21 nm were also observed by AFM analysis in a physiological solution condition, suggesting that the segments along the filaments are an intrinsic substructure of vimentin IFs. In the course of IF assembly, assembly intermediates were analyzed in air. Many short filaments with a full-width and an apparent length of approximately 78 nm (evaluated length approximately 69 nm) were observed immediately after initiation of the assembly reaction. Interestingly, the short full-width filaments appeared to be composed of the four segments. Further incubation enabled the short full-width filaments to anneal longitudinally into longer filaments with a distinct elongation step of approximately 40 nm, which corresponds to the length of the two segments. To explain these observations, we propose a vimentin IF formation model in which vimentin dimers are supercoiling around the filament axis.

Annular Oligomeric Amyloid Intermediates Observed by in Situ Atomic Force Microscopy

Amyloidoses and related protein deposition diseases involve the transformation of normally soluble proteins into insoluble deposits, usually fibrillar in nature. Although it was originally assumed that the fibrils were the toxic species, this assumption has recently been called into question. Accumulating evidence in several systems suggests that oligomeric intermediates on the aggregation pathway may be toxic. In the present study we used in situ atomic force microscopy to monitor aggregation in aqueous solution in real time. The sample used was an amyloidogenic immunoglobulin light chain, involved in AL or light chain amyloidosis. The nature of the observed oligomeric intermediates was dependent on the conditions of incubation, especially pH and ionic strength. Several different aggregation intermediates with a variety of morphologies, including annular or torus-shaped species, were observed. The data indicate that protein aggregation can be very complex, involving a variety of different oligomeric intermediates whose population will be determined by the kinetic and thermodynamic competition between them.

An overview of the biophysical applications of atomic force microscopy

The potentialities of the atomic force microscopy (AFM) make it a tool of undeniable value for the study of biologically relevant samples. AFM is progressively becoming a usual benchtop technique. In average, more than one paper is published every day on AFM biological applications. This figure overcomes materials science applications, showing that 17 years after its invention, AFM has completely crossed the limits of its traditional areas of application. Its potential to image the structure of biomolecules or bio-surfaces with molecular or even sub-molecular resolution, study samples under physiological conditions (which allows to follow in situ the real time dynamics of some biological events), measure local chemical, physical and mechanical properties of a sample and manipulate single molecules should be emphasized.

3-D morphological characterization of the liver parenchyma by atomic force microscopy and by scanning electron microscopy

A comparative study of atomic force microscopy (AFM) and scanning electron microscopy (SEM) imaging of the healthy human liver parenchyma was carried out to determine the similarities and the differences. In this study, we compared the fine hepatic structures as observed by SEM and AFM. Although AFM revealed such typical hepatic structures as bile canaliculi and hepatocytes, it also showed the location of the nucleus and chromatin granules in rough relief structure, which was not visible by SEM. By contrast, SEM visualized other structures, such as microvilli, the central vein, and collagenous fibers, none of which was visualized by AFM. For better orientation and confirmation of most of the structures imaged by SEM and AFM, Congo Red-stained specimens were also examined. Amyloid deposits in the Disse's spaces were shown especially clearly in these images. The differences between the SEM and AFM images reflected the characteristics of the detection systems and methods used for sample preparation. Our results reveal that more detailed information on hepatic morphology is obtained by exploiting the advantages of both SEM and AFM.

Investigations into the life cycle of the bacterial predator Bdellovibrio bacteriovorus 109J at an interface by atomic force microscopy

Atomic force microscopy was used to image Bdellovibrio bacteriovorus 109J, a gram-negative bacterial predator that consumes a variety of other gram-negative bacteria. In predator-prey communities grown on filters at hydrated air-solid interfaces, repeated cycles of hunting, invasion, growth, and lysis occurred readily even though the cells were limited to near two-dimensional movement. This system allowed us to image the bacteria directly without extensive preparation or modification, and many of the cells remained alive during imaging. Presented are images of the life cycle in two species of prey organisms, both Escherichia coli (a small prey bacterium that grows two-dimensionally on a surface) and Aquaspirillum serpens (a large prey bacterium that grows three-dimensionally on a surface), including high-resolution images of invaded prey cells called bdelloplasts. We obtained evidence for multiple invasions per prey cell, as well as significant heterogeneity in morphology of bdellovibrios. Mutant host-independent bdellovibrios were observed to have flagella and to excrete a coating that causes the predators to clump together on a surface. Most interestingly, changes in the texture of the cell surface membranes were measured during the course of the invasion cycle. Thus, coupled with our preparation method, atomic force microscopy allowed new observations to be made about Bdellovibrio at an interface. These studies raise important questions about the ways in which bacterial predation at interfaces (air-solid or liquid-solid) may be similar to or different from predation in solution.

Full-length rat amylin forms fibrils following substitution of single residues from human amylin

Pancreatic amyloid deposits, composed of the 37 amino acid residue peptide amylin, represent an integral part of type 2 diabetes mellitus pathology. Human amylin (hA) forms fibrils in vitro and is toxic to cultured pancreatic islet beta-cells. In contrast, rat amylin (rA) which differs from hA by only six amino acid residues in the central region of the peptide, residues 18-29, does not form fibrils and is not cytotoxic. To elucidate the role of individual residues in fibril formation, we have generated a series of full-length rA variants and examined their ability to form fibrils in vitro. Single-residue substitutions with amino acids from corresponding positions of the hA sequence, i.e. R18H, L23F, or V26I, were sufficient to render rA competent for fibril formation albeit at a small yield. Combining two or three of these substitutions generally increased the ability to produce fibrils. Variant rA fibril morphologies were examined by negative stain electron microscopy and found to be similar to those generated by hA itself. Bulk assays, i.e. involving thioflavin-T fluorescence and sedimentation, showed that the amount of fibril formation was relatively small for these rA variants when compared to hA under the same conditions. Fibril growth was demonstrated by time-lapse atomic force microscopy, and MALDI-TOF mass spectrometry was used to verify that fibrils consisted of full-length peptide. Our observations confirm previous reports that the three proline residues play a dominant negative role in fibril formation. However, their presence is not sufficient to completely abolish the ability of rA to form fibrils, as each of the other three implicated residues (i.e. R18, L23 and V26) also has a dominant modulating effect.

Surface-catalyzed amyloid fibril formation

Light chain (or AL) amyloidosis is characterized by the pathological deposition of insoluble fibrils of immunoglobulin light chain fragments in various tissues, walls of blood vessels, and basement membranes. In the present investigation, the in vitro assembly of a recombinant amyloidogenic light chain variable domain, SMA, on various surfaces was monitored using atomic force microscopy. SMA formed fibrils on native mica at pH 5.0, conditions under which predominantly amorphous aggregates form in solution. Fibril formation was accelerated significantly on surfaces compared with solution; for example, fibrils grew on surfaces at significantly faster rates and at much lower concentrations than in solution. No fibrils were observed on hydrophobic or positively charged surfaces or at pH >7.0. Two novel types of fibril growth were observed on the surface: bidirectional linear assembly of oligomeric units, and linear growth from preformed amorphous cores. In addition to catalyzing the rate of fibrillation, the mechanism of fibril formation on the surfaces was significantly different from in solution, but it may be more physiologically relevant because in vivo the deposits are associated with surfaces.

Regulation of nuclear pore complex conformation by IP(3) receptor activation

In recent years, both the molecular architecture and functional dynamics of nuclear pore complexes (NPCs) have been revealed with increasing detail. These large, supramolecular assemblages of proteins form channels that span the nuclear envelope of cells, acting as crucial regulators of nuclear import and export. From the cytoplasmic face of the nuclear envelope, nuclear pore complexes exhibit an eightfold symmetric ring structure encompassing a central lumen. The lumen often appears occupied by an additional structure alternatively referred to as the central granule, nuclear transport complex, or nuclear plug. Previous studies have suggested that the central granule may play a role in mediating calcium-dependent regulation of diffusion across the nuclear envelope for intermediate sized molecules (10-40 kDa). Using atomic force microscopy to measure the surface topography of chemically fixed Xenopus laevis oocyte nuclear envelopes, we present measurements of the relative position of the central granule within the NPC lumen under a variety of conditions known to modify nuclear Ca(2+) stores. These measurements reveal a large, approximately 9-nm displacement of the central granule toward the cytoplasmic face of the nuclear envelope under calcium depleting conditions. Additionally, activation of nuclear inositol triphosphate (IP(3)) receptors by the specific agonist, adenophostin A, results in a concentration-dependent displacement of central granule position with an EC(50) of ~1.2 nM. The displacement of the central granule within the NPC is observed on both the cytoplasmic and nucleoplasmic faces of the nuclear envelope. The displacement is blocked upon treatment with xestospongin C, a specific inhibitor of IP(3) receptor activation. These results extend previous models of NPC conformational dynamics linking central granule position to depletion of IP(3) sensitive nuclear envelope calcium stores.