Study of BOD microbial sensors for waste water treatment control

Short-range remote sensing of water quality by a handheld fluorosensor system

Laser-induced fluorescence is a powerful measurement method for determining the concentration of organic pollutants as well as the amount of algae in water. It can be applied in remote sensing of natural waters and has the advantages of high speed and sensitivity. In this paper, we present a compact handheld fluorosensor system for water quality assessment. The power of the technique is demonstrated in measurements at a river system in South China.

Toxicity assessment using different bioassays and microbial biosensors

Toxicity assessment of water streams, wastewater, and contaminated sediments, is a very important part of environmental pollution monitoring. Evaluation of biological effects using a rapid, sensitive and cost effective method can indicate specific information on ecotoxicity assessment. Recently, different biological assays for toxicity assessment based on higher and lower organisms such as fish, invertebrates, plants and algal cells, and microbial bioassays have been used. This review focuses on microbial biosensors as an analytical device for environmental, food, and biomedical applications. Different techniques which are commonly used in microbial biosensing include amperometry, potentiometry, conductometry, voltammetry, microbial fuel cells, fluorescence, bioluminescence, and colorimetry. Examples of the use of different microbial biosensors in assessing a variety of environments are summarized.

Methods for assessing biochemical oxygen demand (BOD): a review

The Biochemical Oxygen Demand (BOD) is one of the most widely used criteria for water quality assessment. It provides information about the ready biodegradable fraction of the organic load in water. However, this analytical method is time-consuming (generally 5 days, BOD5), and the results may vary according to the laboratory (20%), primarily due to fluctuations in the microbial diversity of the inoculum used. Work performed during the two last decades has resulted in several technologies that are less time-consuming and more reliable. This review is devoted to the analysis of the technical features of the principal methods described in the literature in order to compare their performances (measuring window, reliability, robustness) and to identify the pros and the cons of each method.

Microbial biosensors

A microbial biosensor is an analytical device that couples microorganisms with a transducer to enable rapid, accurate and sensitive detection of target analytes in fields as diverse as medicine, environmental monitoring, defense, food processing and safety. The earlier microbial biosensors used the respiratory and metabolic functions of the microorganisms to detect a substance that is either a substrate or an inhibitor of these processes. Recently, genetically engineered microorganisms based on fusing of the lux, gfp or lacZ gene reporters to an inducible gene promoter have been widely applied to assay toxicity and bioavailability. This paper reviews the recent trends in the development and application of microbial biosensors. Current advances and prospective future direction in developing microbial biosensor have also been discussed.

Co-immobilized microbial biosensor for BOD estimation based on sol-gel derived composite material

A novel type of biochemical oxygen demand (BOD) biosensor was developed for water monitor, based on co-immobilizing of Trichosporon cutaneum and Bacillus subtilis in the sol-gel derived composite material which is composed of silica and the grafting copolymer of poly (vinyl alcohol) and 4-vinylpyridine (PVA-g-P(4-VP)). Factors that influence the performance of the resulting biosensor were examined. The biodegradable substrate spectrum could be expanded by the co-immobilized microorganisms. The biosensor prepared also exhibited good reproducibility and long-term stability. Good agreement was obtained between the results of the sensor BOD measurement and those obtained from conventional BOD(5) method for water samples.

Microbial BOD sensors for wastewater analysis

The field of biosensors for measuring biochemical oxygen demand (BOD) is reviewed. Particularly, BOD sensors constructed on the biofilm configuration are discussed regarding performance characteristics like linearity, response time, precision, agreement between BOD values obtained from the biosensors and the conventional 5-days test, as well as toxic resistance to various compounds and operational stability. The techniques for improving the agreement between the sensor BOD and BOD5 are described. Information provided also includes BOD biosensors based on respirometers and other measuring principles, the commercial BOD instruments, as well as the current limitations of BOD biosensor development.

Characterization of two novel yeast strains used in mediated biosensors for wastewater

After isolation from a pulp mill wastewater treatment facility, two yeast strains, designated SPT1 and SPT2, were characterized and used in the development of mediated biochemical oxygen demand (BOD) biosensors for wastewater. 18S rRNA gene sequence analysis revealed a one nucleotide difference between the sequence of SPT1 and those of Candida sojae and Candida viswanthii. While SPT2 had the highest overall homology to Pichia norvegensis, at only 73.5%, it is clearly an ascomycete, based on BLAST comparisons and phylogenetic analyses. Neighbor-joining dendrograms indicated that SPT1 clustered with several Candida spp., and that SPT2 clustered with Starmera spp., albeit as a very deep branch. Physiological tests, microscopic observations, and fatty acid analysis confirmed that SPT1 and SPT2 are novel yeast strains. Physiological tests also indicated that both strains had potential for use in mediated biosensors for estimation of BOD in wastewater. The lower detection limits of SPT1- and SPT2-based K3Fe(CN)6-mediated biosensors for a pulp-mill effluent were 2 and 1 mg BOD/L, respectively. Biosensor-response times for effluents from eight different pulp mills were in the range of 5 min. Reliability and sensitivity of the SPT1- and SPT2-based biosensors were good, but varied with the wastewater.

Microbial sensors on a respiratory basis for wastewater monitoring

In respect of their rapidity, their online capabilities, and their moderate costs, biosensing systems generally offer an attractive alternative to the existing methods of water analysis. Additionally, one particular advantage of microbial biosensors is the ability to measure direct effects on living cells, e.g., their respiratory activity and its alteration caused by environmental pollutants. It is true that microbial sensors, often do not provide the optimum solution for the determination of individual analytes when compared to established physico-chemical analysis methods. However, these biosensing devices are predestined for the summary determination of environmentally relevant compounds and their complex effects, respectively. For this reason, microbial sensors allow an integral evaluation of the degree of environmental pollution including the interaction of various compounds. Moreover, in some cases specific metabolic pathways in microorganisms are used, resulting in the development of microbial sensors for the more selective analysis for those compounds or pollutants, which cannot be measured by simple enzyme reactions, e.g., the determination of aromatic compounds and heavy metals. This chapter gives an overview of microbiological biosensors on respiratory basis for the measurement of the following environmentally relevant compounds: inorganic N-compounds, heavy metals, organic xenobiotics and the estimation of sum parameters or so-called complex parameters such as BOD, ADOC, N-BOD, and the inhibition of nitrification.

Barriers to sustainable water-quality management

Due to the pressures of increasing population and developing economy all over the world, the present situation of water-quality management is far from satisfactory. To enhance sustainability of water-quality-management systems, in-depth research of the related barriers and the relevant mitigation approaches is desired. In this paper, recent developments, advancements, challenges, and barriers associated with practices of water-quality management were analyzed. A number of related methodologies, applications, and policy considerations were examined. Issues of information support, technology development, system integration, and policy implementation were discussed. Perspectives of sustainable water-quality management in the twenty-first century were investigated, demonstrating many demanding areas for enhanced research efforts, including issues of data availability and reliability, concerns in system complexity and methodology validity, limitations of computer techniques, usefulness of research outputs, difficulties in policy implementation, and necessity of training programs.

Immobilised activated sludge based biosensor for biochemical oxygen demand measurement

A biochemical oxygen demand (BOD) sensor, based on an immobilised mixed culture of microorganisms in combination with a dissolved oxygen electrode, has been developed for the purpose of on-line monitoring of the biological treatment process for waste and wastewater. The sensor was designed for easy replacement of the biomembrane, thereby making it suitable for short-term use. The drawbacks of activated sludge based sensor, such as short sensor lifetime, were thereby circumvented. The sensor BOD measurements were carried out in the kinetic mode using a flow injection system, resulting in 25 s for one measurement followed by 4-8 min recovery time. Based on the results of normalised sensor responses, the OECD synthetic wastewater was considered to be a more suitable calibration solution in comparison with the GGA solution. Good agreement was achieved between the results of the sensor BOD measurement and those obtained from BOD5 analysis of a wastewater sample from a food-processing factory. Reproducibility of responses using one sensor was below +/- 5.6%, standard deviation. Reproducibility of responses using different sensors was within acceptable bias limits, viz. +/- 15% standard deviation.

Measurement of biodegradable substances using the salt-tolerant yeast Arxula adeninivorans for a microbial sensor immobilized with poly(carbamoyl)sulfonate (PCS). Part II: Application of the novel biosensor to real samples from coastal and island regions

A microbial sensor for rapid measurement of the amount of biodegradable substances based on the salt-tolerant yeast Arxula adeninivorans LS3 has been developed especially for coastal and island regions. Our parameter, the so-called sensorBOD, that is available after only a few minutes, agrees with the 5-day value for the biochemical oxygen demand (BOD5) very well. We have employed the Arxula sensor in the short-time estimation and supervision of the BOD of both domestic and industrial wastewater with high salinity. The novel sensor makes it possible to monitor the different types of wastewater rapidly without pretreatment, and it can be used for an active process control of sewage treatment works. Compared to a commercially available sensor, the novel sensor achieves better agreement between sensorBOD and BOD5 measurements with salt containing samples.

Biochemical oxygen demand sensor using Serratia marcescens LSY 4

A microbial biochemical oxygen demand (BOD) sensor consisting of Serratia marcescens LSY 4 and an oxygen electrode was prepared for estimation of the biochemical oxygen demand. The response of the BOD sensor was insensitive to pH in the range of pH 6.0-8.0, and the baseline drift of the signal was nearly absent even in unbuffered aqueous solution. Because heavy metal ions were precipitated from the phosphate buffer solution, unbuffered solution was used to investigate the effect of the concentration of heavy metal ions on the sensor response. Contrary to previous studies, not only Cu2+ and Ag+ but also Cd2+ and Zn2+ significantly decreased the response of the BOD sensor in unbuffered solution. Graft polymerization of sodium styrene sulfonate on the surface of the porous teflon membrane was carried out to absorb the heavy metal ions permeating through the membrane. Tolerance against Zn2+ was induced for S. marcescens LSY 4 to make the cells less sensitive to the presence of heavy metal ions. The membrane modification and the Zn2+ tolerance induction showed some positive effects in such a way that they reduced the inhibitory effects of Zn2+ and Cd2+ on the sensitivity of the BOD sensor. However, they had no effect on the protection of the cells against the interference of Cu2+ and Ag+ on the performance of the sensor.

Immobilized cells used for detection and analysis

Many kinds of biosensor have now been developed and utilized for various types of analysis including clinical, medical and environmental monitoring, industrial process control, as well as many other applications. The microbial biosensor has advantages, such as longer lifetime and lower cost, over other types of biosensor. Recently, photobacteria and recombinant bacteria have been employed in biosensors both for determining biochemical oxygen demand and for detecting heavy metals and other toxic compounds.