Material ejection and redeposition following atmospheric pressure near-field laser ablation on molecular solids

High resolution laser mass spectrometry bioimaging

Mass spectrometry imaging (MSI) was introduced more than five decades ago with secondary ion mass spectrometry (SIMS) and a decade later with laser desorption/ionization (LDI) mass spectrometry (MS). Large biomolecule imaging by matrix-assisted laser desorption/ionization (MALDI) was developed in the 1990s and ambient laser MS a decade ago. Although SIMS has been capable of imaging with a moderate mass range at sub-micrometer lateral resolution from its inception, laser MS requires additional effort to achieve a lateral resolution of 10μm or below which is required to image at the size scale of single mammalian cells. This review covers untargeted large biomolecule MSI using lasers for desorption/ionization or laser desorption and post-ionization. These methods include laser microprobe (LDI) MSI, MALDI MSI, laser ambient and atmospheric pressure MSI, and near-field laser ablation MS. Novel approaches to improving lateral resolution are discussed, including oversampling, beam shaping, transmission geometry, reflective and through-hole objectives, microscope mode, and near-field optics.

Femtosecond laser ablation-based mass spectrometry: An ideal tool for stoichiometric analysis of thin films

An accurate and routinely available method for stoichiometric analysis of thin films is a desideratum of modern materials science where a material’s properties depend sensitively on elemental composition. We thoroughly investigated femtosecond laser ablation-inductively coupled plasma-mass spectrometry (fs-LA-ICP-MS) as an analytical technique for determination of the stoichiometry of thin films down to the nanometer scale. The use of femtosecond laser ablation allows for precise removal of material with high spatial and depth resolution that can be coupled to an ICP-MS to obtain elemental and isotopic information. We used molecular beam epitaxy-grown thin films of LaPd_(x)Sb₂ and T^′-La₂CuO₄ to demonstrate the capacity of fs-LA-ICP-MS for stoichiometric analysis and the spatial and depth resolution of the technique. Here we demonstrate that the stoichiometric information of thin films with a thickness of ~10 nm or lower can be determined. Furthermore, our results indicate that fs-LA-ICP-MS provides precise information on the thin film-substrate interface and is able to detect the interdiffusion of cations.

Tip-enhanced laser ablation sample transfer for biomolecule mass spectrometry

Atomic force microscope (AFM) tip-enhanced laser ablation was used to transfer molecules from thin films to a suspended silver wire for off-line mass spectrometry using laser desorption ionization (LDI) and matrix-assisted laser desorption ionization (MALDI). An AFM with a 30 nm radius gold-coated silicon tip was used to image the sample and to hold the tip 15 nm from the surface for material removal using a 355 nm Nd:YAG laser. The ablated material was captured on a silver wire that was held 300 μm vertically and 100 μm horizontally from the tip. For the small molecules anthracene and rhodamine 6G, the wire was cut and affixed to a metal target using double-sided conductive tape and analyzed by LDI using a commercial laser desorption time-of-flight mass spectrometer. Approximately 100 fg of material was ablated from each of the 1 μm ablation spots and transferred with approximately 3% efficiency. For larger polypeptide molecules angiotensin II and bovine insulin, the captured material was dissolved in saturated matrix solution and deposited on a target for MALDI analysis.

The effect of ultrafast laser wavelength on ablation properties and implications on sample introduction in inductively coupled plasma mass spectrometry

We investigated the role of femtosecond (fs) laser wavelength on laser ablation (LA) and its relation to laser generated aerosol counts and particle distribution, inductively coupled plasma-mass spectrometry (ICP-MS) signal intensity, detection limits, and elemental fractionation. Four different NIST standard reference materials (610, 613, 615, and 616) were ablated using 400 nm and 800 nm fs laser pulses to study the effect of wavelength on laser ablation rate, accuracy, precision, and fractionation. Our results show that the detection limits are lower for 400 nm laser excitation than 800 nm laser excitation at lower laser energies but approximately equal at higher energies. Ablation threshold was also found to be lower for 400 nm than 800 nm laser excitation. Particle size distributions are very similar for 400 nm and 800 nm wavelengths; however, they differ significantly in counts at similar laser fluence levels. This study concludes that 400 nm LA is more beneficial for sample introduction in ICP-MS, particularly when lower laser energies are to be used for ablation.

Tip preparation for near-field ablation at mid-infrared wavelengths

A fabrication method for high-throughput, fiber-based tips for near-field scanning microscopy (NSOM) in the mid-infrared (λ ~ 3 μm) has been developed. Several fiber materials have been investigated and recipes for wet-chemical etching have been varied to produce tips that are physically robust and are capable of low-loss transmission of high-power pulses of mid-infrared light. Ultimately, wet-chemical etching techniques are used on glass fibers to produce tips capable of focusing mid-infrared light to ablate material from sub-micron-sized regions of organic films. The power throughput of the tips is significantly increased by using a novel material, previously unreported for NSOM applications: germanate fibers. The tips produced are mechanically strong and capable of transmitting high light fluence without sustaining physical damage. Here, the development of these tips and their performance are described.

Active capillary plasma source for ambient mass spectrometry

RATIONALE

Imaging mass spectrometry with high spatial resolution has become a rapidly developing area of mass spectrometric research. Many scientific and industrial problems deal with mass spectrometric analysis at ambient pressures. This requires efficient transport and ionization of small amounts of substance.

METHODS

An active sampling capillary based on a dielectric barrier discharge was constructed for ambient mass spectrometry. The capillary serves as an ionization source as well as an atmospheric interface of the mass spectrometer. The analyzed samples are transported through the sampling capillary due to the pressure difference between the atmospheric environment and the vacuum in the mass spectrometer. Ionization of the transported samples is provided by a low-temperature dielectric barrier discharge. This active capillary was shown to work in a robust fashion for ionizing both gas-phase and laser-ablated solid-phase samples.

RESULTS

The geometry of the electrodes was found to play a crucial role in ionization efficiency. The capillary was optimized in order to perform surface analysis of solid samples. Sensitivity tests were carried out to characterize different active capillary constructions. The sensitivity of the constructed active capillary was 0.1 ppb (relative concentration of a gaseous sample in ambient air). The active capillary was able to detect samples evaporated from a solid surface. With the active capillary source, it was possible to detect anthracene traces evaporated from a surface located 3 cm from the capillary inlet.

CONCLUSIONS

A plasma-based active capillary ionization source was constructed. This concept of an active sample inlet should broaden the range of applications of ambient mass spectrometry.

Spray desorption collection: an alternative to swabbing for pharmaceutical cleaning validation

Spray Desorption Collection (SDC) allows for much larger areas of surfaces to be sampled compared to traditional swabbing techniques, providing a valuable pre-concentration advantage. Closely related to desorption electrospray ionization (DESI), analytes from the sample surface are collected onto a selected collection surface, which in a second step can be analyzed directly. Here we demonstrate the application of SDC as a large surface area sampling tool coupled with paper spray MS (PS-MS) and demonstrate its capabilities for cleaning validation of pharmaceutical equipment for both acidic and basic active ingredients from an aluminium surface.