A smartphone colorimetric reader integrated with an ambient light sensor and a 3D printed attachment for on-site detection of zearalenone

A label-free visual aptasensor for zearalenone detection based on target-responsive aptamer-cross-linked hydrogel and color change of gold nanoparticles

ZEN-responsive hydrogel was prepared using ZEN aptamer and a cationic conjugated skeleton which was formed by the electrostatic interaction between acrylamide and poly (diallyldimethylammonium chloride) (PDDA). In the presence of ZEN, the binding of aptamer and ZEN caused the hydrogel to dissociate, releasing the gold nanoparticles (AuNPs) encapsulated in the hydrogel into supernatant, whose color changes serving as response instructions were observed by eyes. To realize low dose visual detection, the TMB-H₂O₂ was used for quantitative readout by AuNPs released from the hydrogel which can efficiently catalyze the reaction to generate a obvious change.There was a good linear relationship between the changed absorbance and concentration of ZEN within 2.5-100 ng/mL, a detection limit of 0.98 ng/mL, recovery rates of 98.8%-101.3% and 99.8%-101.5% for corns and beer, respectively. This developed sensing strategy would provide a promising application for other mycotoxins by replacing the corresponding aptamer sequences.

A visual and reversible nanoprobe for rapid and on-site determination of hexavalent chromium and lysine based on dual-emission carbon quantum dots coupled with smartphone

A straightforward, largely instrument-free, smartphone-based analytical strategy for hexavalent chromium and lysine (Lys) on-site detection via exploitation of dual-emission carbon quantum dots (DECQDs) has been demonstrated. DECQDs show dual-emission peaks at 439 and 630 nm with the excitation at 375 nm. As a dual-mode detection probe, the fluorescence and ultraviolet adsorption spectra of DECQDs vary with hexavalent chromium concentrations. Most importantly, Lys can restore the fluorescence of the hexavalent chromium added DECQD nanoprobe and change the color of the probe under natural light. At the same time, based on the participation of smartphones, the prepared DECQD probes favor the establishment of visual smart sensors that can also be used for the in-situ detection of targets. The on-site quantitative analysis exhibited a linear range of 5.3-320 μM with a detection limit of 1.6 μM towards Cr(VI) and the differentiation of Lys variation from 1 to 75 mM with a detection limit of 0.3 mM. The probe has been applied for the first time to enable vision-based colorimetric in complex samples such as water, milk and egg. The recoveries of Cr(VI) and Lys in real samples were between 90 and 104%, and the relative standard deviation (RSD) was as low as 0.4%. This work offers new perspectives for fundamental understanding and new design of functional luminescent materials that are applicable for food-safety and rapid and intelligent inspection. A straightforward, large instrument-free, smartphone-based analytical strategy with dual-emission carbon quantum dots was developed for hexavalent chromium and Lys on-site detection via fluorescent and colorimetric twofold readout measure.

Low-Cost Microplate Reader with 3D Printed Parts for under 500 USD

A 96-well microplate reader for absorption spectroscopy was designed, constructed, and tested at a total cost of ca. 500 USD. The reduced cost of the device represents the major technical contribution of this manuscript, as costs were reduced 7 fold from previous reports. The device was able to achieve 3σ limits of detection of ca. 0.01 absorbance units (AU) over a 60 second measurement for the mid-visible wavelength range. Component parts are either commercially available, or 3D printed from plans. Analysis wavelength can be altered throughout the visible region through use of various photographic or theatrical filters. This feature allows the well plate reader to be used for typical laboratory assays such as cell population estimation by optical density (OD) at 600 nm, or enzyme-linked immunosorbent assays (ELISA) at 450 nm. This manuscript reports on the motivation and process of constructing the device, lists required parts, presents data demonstrating device function, and provides the community of scholars with plans to reproduce the work. The device can be reproduced in laboratories lacking sufficient resources to purchase commercially available options and this outcome contributes towards empowerment of individuals and equity of scientific enquiry.

ColoriSens: An open-source and low-cost portable color sensor board for microfluidic integration with wireless communication and fluorescence detection

Microfluidic colorimetric biosensors have shown promising potential for detecting metal cations, anions, organic dyes, drugs, pesticides. As for today, most colorimetric sensors are read by a smartphone or professional optical imaging system, and there is still a lack of an affordable and reliable colorimetric detector for the microfluidic chip. Integrating those reading and detection capabilities into a microfluidic system is essential for point-of-care (POC) detection and can enable more complex microfluidic operations, such as lab-on-a-chip experiments or programmable microfluidics. We developed an open-source colorimetric detection sensor board that can be integrated into the existing microfluidic system. This sensor board has a built-in UV source that enables fluorescence detection. With built-in USB and Wi-Fi connectivity and a set of simple APIs, microfluidic systems can communicate directly with this sensor board, even wirelessly. The sensor was designed for low-cost. With a total build cost of less than 12 EUR per unit, it is ideal for low-cost systems and DIY microfluidic users. Along with the sensor board, we also designed a companion microfluidic chip carrier cartridge which can be modified depending on the chip's dimension. To demonstrate the sensor, we also developed a cross-platform open-source client application to demonstrate the communication APIs and the functionality of the sensor board.

Development of a Smartphone-Integrated Reflective Scatterometer for Bacterial Identification

We present a smartphone-based bacterial colony phenotyping instrument using a reflective elastic light scattering (ELS) pattern and the resolving power of the new instrument. The reflectance-type device can acquire ELS patterns of colonies on highly opaque media as well as optically dense colonies. The novel instrument was built using a smartphone interface and a 532 nm diode laser, and these essential optical components made it a cost-effective and portable device. When a coherent and collimated light source illuminated a bacterial colony, a reflective ELS pattern was created on the screen and captured by the smartphone camera. The collected patterns whose shapes were determined by the colony morphology were then processed and analyzed to extract distinctive features for bacterial identification. For validation purposes, the reflective ELS patterns of five bacteria grown on opaque growth media were measured with the proposed instrument and utilized for the classification. Cross-validation was performed to evaluate the classification, and the result showed an accuracy above 94% for differentiating colonies of E. coli, K. pneumoniae, L. innocua, S. enteritidis, and S. aureus.

Recent Advances in 3D Printing of Biomedical Sensing Devices

Additive manufacturing, also called 3D printing, is a rapidly evolving technique that allows for the fabrication of functional materials with complex architectures, controlled microstructures, and material combinations. This capability has influenced the field of biomedical sensing devices by enabling the trends of device miniaturization, customization, and elasticity (i.e., having mechanical properties that match with the biological tissue). In this paper, the current state-of-the-art knowledge of biomedical sensors with the unique and unusual properties enabled by 3D printing is reviewed. The review encompasses clinically important areas involving the quantification of biomarkers (neurotransmitters, metabolites, and proteins), soft and implantable sensors, microfluidic biosensors, and wearable haptic sensors. In addition, the rapid sensing of pathogens and pathogen biomarkers enabled by 3D printing, an area of significant interest considering the recent worldwide pandemic caused by the novel coronavirus, is also discussed. It is also described how 3D printing enables critical sensor advantages including lower limit-of-detection, sensitivity, greater sensing range, and the ability for point-of-care diagnostics. Further, manufacturing itself benefits from 3D printing via rapid prototyping, improved resolution, and lower cost. This review provides researchers in academia and industry a comprehensive summary of the novel possibilities opened by the progress in 3D printing technology for a variety of biomedical applications.

A gold nanoparticle-based visual aptasensor for rapid detection of acetamiprid residues in agricultural products using a smartphone

Based on the colorimetric analysis of gold nanoparticles and a smartphone readable strategy, a stable, sensitive, and visual method was established for rapid detection of acetamiprid residues in agricultural products. By optimizing the key parameters, the detection process only took 40 minutes with good specificity. The acetamiprid aptamer can help AuNPs to resist salt-induced aggregation. Conversely, in the presence of acetamiprid, the anti-protection is weakened and the AuNPs aggregated with the color change of the solution. The photographs of the solution are recorded by the smartphone and analyzed through image processing. In the range from 25 to 300 μM the method can realize a quantitative analysis of acetamiprid, and the detection limit is about 3.81 μM. Excellent recoveries are taken in samples of cucumber, cabbage, and river water, ranging from 96.78% to 129.95%. These results show no significant difference from the results obtained by the microplate reader. What's more, the method employs a smartphone to read without the assistance of professional equipment, which greatly reduces the cost of detection, and shows a promising application prospect for on-site rapid detection of acetamiprid.

Smartphone-Based Device for Colorimetric Detection of MicroRNA Biomarkers Using Nanoparticle-Based Assay

The detection of microRNAs (miRNAs) is emerging as a clinically important tool for the non-invasive detection of a wide variety of diseases ranging from cancers and cardiovascular illnesses to infectious diseases. Over the years, miRNA detection schemes have become accessible to clinicians, but they still require sophisticated and bulky laboratory equipment and trained personnel to operate. The exceptional computing ability and ease of use of modern smartphones coupled with fieldable optical detection technologies can provide a useful and portable alternative to these laboratory systems. Herein, we present the development of a smartphone-based device called Krometriks, which is capable of simple and rapid colorimetric detection of microRNA (miRNAs) using a nanoparticle-based assay. The device consists of a smartphone, a 3D printed accessory, and a custom-built dedicated mobile app. We illustrate the utility of Krometriks for the detection of an important miRNA disease biomarker, miR-21, using a nanoplasmonics-based assay developed by our group. We show that Krometriks can detect miRNA down to nanomolar concentrations with detection results comparable to a laboratory-based benchtop spectrophotometer. With slight changes to the accessory design, Krometriks can be made compatible with different types of smartphone models and specifications. Thus, the Krometriks device offers a practical colorimetric platform that has the potential to provide accessible and affordable miRNA diagnostics for point-of-care and field applications in low-resource settings.

Colorimetric ratiometry with ion optodes for spatially resolved concentration analysis

The deprotonation degree of the lipophilic pH indicator dye (chromoionophore) in ionophore-based ion optodes (so-called bulk optodes) has traditionally been measured spectrophotometrically. This makes it difficult to obtain spatially resolved concentration information, for example in the study of heterogenous systems. This article reports on a new colorimetric method that relies on a ratiometric image analysis. The acquision of image data allows one to map the deprotonation degree in two dimensions, which in turn is used to obtain the spatially-resolved ion concentration of the image. Using the detection of potassium as an example, the deprotonation degree data calculated on the basis of image analysis correlate quantitatively with those from spectrophotometry. They showed no dependence on the type of camera used in spite of their different gamma correction values and spectral sensitivities, as expected from theory. As an example, the method is successfully applied to the pixel level analysis of an ensemble of pictures acquired at different times to spatially and temporally observe potassium ion diffusion into an agarose gel containing a potassium-selective optical sensor microemulsion.

Field analysis of Cr(vi) in water samples by using a smartphone-based ultralong absorption path reflection colorimetric device

Hexavalent chromium is highly toxic and regarded as one of the main pollutants in the environment. A multiple reflection colorimetric cell is designed to improve the sensitivity in field analysis for Cr(vi).

An explorative study of polymers for 3D printing of bioanalytical test systems

BACKGROUND

The 3D printing is relevant as a manufacturing technology of functional models for forensic, pharmaceutical and bioanalytical applications such as drug delivery systems, sample preparation and point-of-care tests.

OBJECTIVE

Melting behavior and autofluorescence of materials are decisive for optimal printing and applicability of the product which are influenced by varying unknown additives.

METHODS

We have produced devices for bioanalytical applications from commercially available thermoplastic polymers using a melt-layer process. We characterized them by differential scanning calorimetry, fluorescence spectroscopy and functional assays (DNA capture assay, model for cell adhesion, bacterial adhesion and biofilm formation test).

RESULTS

From 14 tested colored, transparent and black materials we found only deep black acrylonitrile-butadiene-styrene (ABS) and some black polylactic acid (PLA) useable for fluorescence-based assays, with low autofluorescence only in the short-wave range of 300-400 nm. PLA was suitable for standard bioanalytical purposes due to a glass transition temperature of approximately 60°C, resistance to common laboratory chemicals and easy print processing. For temperature-critical methods, such as hybridization reactions up to 90°C, ABS was better suited.

CONCLUSIONS

Autofluorescence was not a disadvantage per se but can also be used as a reference signal in assays. The rapid development of individual protocols for sample processing and analysis required the availability of a material with consistent quality over time. For fluorescence-based assays, the use of commercial standard materials did not seem to meet this requirement.

Smartphone-based optical assays in the food safety field

Smartphone based devices (SBDs) have the potential to revolutionize food safety control by empowering citizens to perform screening tests. To achieve this, it is of paramount importance to understand current research efforts and identify key technology gaps. Therefore, a systematic review of optical SBDs in the food safety sector was performed. An overview of reviewed SBDs is given focusing on performance characteristics as well as image analysis procedures. The state-of-the-art on commercially available SBDs is also provided. This analysis revealed several important technology gaps, the most prominent of which are: (i) the need to reach a consensus regarding optimal image analysis, (ii) the need to assess the effect of measurement variation caused by using different smartphones and (iii) the need to standardize validation procedures to obtain robust data. Addressing these issues will drive the development of SBDs and potentially unlock their massive potential for citizen-based food control.

•

Optical smartphone based sensors in the food safety field are systematically reviewed.

•

Recommendations on image analysis optimization are given.

•

The analytical performance of smartphone based sensors is discussed.

•

Available commercial devises are critically compared.

Label-Free Colorimetric Detection of Urine Glucose Based on Color Fading Using Smartphone Ambient-Light Sensor

In this work, a label-free colorimetric assay was developed for the determination of urine glucose using smartphone ambient-light sensor (ALS). Using horseradish peroxidase—hydrogen peroxide—3,3′,5,5′-tetramethylbenzidine (HRP-H2O2-TMB) colored system, quantitative H2O2 was added to samples to-be-determined for deepest color. The presence of glucose oxidase in urine led to the formation of H2O2 and the reduction of TMBred. As a result of this, the color of the urine faded and the solution changed from deep blue to light blue. We measured the illuminance of the transmitted light by a smartphone ambient light sensor, and thereby color changes were used to calculate the content of urine glucose. After method validation, this colorimetric assay was practically applied for the determination of urine samples from diabetic patients. Good linearity was obtained in the range of 0.039–10.000 mg/mL (R2 = 0.998), and a limit of detection was 0.005 mg/mL. Our method was had high accuracy, sensitivity, simplicity, rapidity, and visualization, providing a new sensor to be potentially applicable for point-of-care detection of urine glucose.

On site determination of free chlorine in water samples by a smartphone-based colorimetric device with improved sensitivity and reliability

Absorbance in a long-path portable colorimetric device was measured by a ratiometric fluorescent strategy in a smartphone platform.

A novel fluorescent immunochromatographic strip combined with pocket fluorescence observation instrument for rapid detection of PRV

Pseudorabies virus (PRV) is an acute and thermal infectious disease in domestic animals. Pigs are a main source of PRV infection, which causes high mortality rates for newborn infected piglets and high miscarriage rates for infected adults. Therefore, early control of PRV is necessary to avoid significant economic loss. We have developed a novel fluorescent immunochromatographic strip (F-ICS) for rapid, sensitive, and specific detection of PRV with a limit of detection (LOD) of 0.13 ng mL^-1 and a detection linear range (DLR) between 0.13 and 2.13 ng mL^-1. The detection limit was about 10 times lower than the colloidal gold strip. In tests of clinical samples, the F-ICS was largely consistent with PCR results, indicating its practical clinical application. In addition, for easy observation of the F-ICS signal by eye, we present a matching 3D-printed pocket fluorescence observation instrument (PFOI) that allows for use of the F-ICS in the field as easily as conventional colloidal gold strips. Graphical Abstract ᅟ.

3D-Printed Biosensor Arrays for Medical Diagnostics

While the technology is relatively new, low-cost 3D printing has impacted many aspects of human life. 3D printers are being used as manufacturing tools for a wide variety of devices in a spectrum of applications ranging from diagnosis to implants to external prostheses. The ease of use, availability of 3D-design software and low cost has made 3D printing an accessible manufacturing and fabrication tool in many bioanalytical research laboratories. 3D printers can print materials with varying density, optical character, strength and chemical properties that provide the user with a vast array of strategic options. In this review, we focus on applications in biomedical diagnostics and how this revolutionary technique is facilitating the development of low-cost, sensitive, and often geometrically complex tools. 3D printing in the fabrication of microfluidics, supporting equipment, and optical and electronic components of diagnostic devices is presented. Emerging diagnostics systems using 3D bioprinting as a tool to incorporate living cells or biomaterials into 3D printing is also reviewed.

Fluorometric lateral flow immunochromatographic zearalenone assay by exploiting a quencher system composed of carbon dots and silver nanoparticles

It is found that the fluorescence of carbon dots (CD) with an emission peak at 459 nm is strongly quenched by silver nanoparticles (AgNPs) with their absorption peak at 430 nm. The finding was applied in a fluorescence quenchometric lateral flow immunochromatographic assay for detection of zearalenone (ZEN) with CDs conjugated to ovalbumin (OVA) as donor signal probe and AgNP-Ab as acceptor signal probe. The assay has an LOD of 0.1 μg·L^-1 for ZEN. This is 10 times better than the respective "turn-off" AgNP-based LFIA. In case of cereal samples and their products, the LODs range from 1 to 2.5 μg·kg^-1. Only minor cross reactivity is found for fusarium toxins, and no cross-sensitivity for aflatoxin B1, T-2 mycotoxin, ochratoxin A, deoxynivalenol, and fumonisin B1. The assay represents a simple, sensitive, and rapid tool for determination of ZEN in cereal samples and their products. Graphical abstract Schematic presentation of fluorescence quenching lateral flow immunochromatographic assay (FLFIA) based on carbon dots (CD) and silver nanoparticle (AgNP) fluorescence resonance energy transfer (FRET) system for the rapid high sensitive detection of zearalenone (ZEN) in cereal samples.

Three kinds of lateral flow immunochromatographic assays based on the use of nanoparticle labels for fluorometric determination of zearalenone

Colloidal gold, quantum dots and polystyrene microspheres were used as labels in three kinds of lateral flow immunochromatographic assays (ICAs) for the detection of zearalenone (ZEN) in cereal samples. The assays allow ZEN to be quantified within 20 min. The LODs are 10 μg·L^-1 of ZEN for the colloidal gold-based ICA, and 1 μg·L^-1 for both the quantum dot and polystyrene microsphere based ICAs. The respective data are 60 μg·kg^-1, 6 μg·kg^-1 and 6 μg·kg^-1, respectively, for spiked samples and cereals. Only minor cross-sensitivity occurred between ZEN and fusarium toxins, and no cross-sensitivity if found for aflatoxin B₁, T-2 mycotoxin, ochratoxin A, deoxynivalenol, and fumonisin B₁. LODs of the three assays are lower than the maximum limits of ZEN set by most standardization agencies. Graphical abstract Schematic presentation of three lateral flow immunochromatographic assays (ICAs) based on the use of (a) colloidal gold (CG), (b) fluorescent quantum dots (QD), and