Simultaneous determination of 44 pharmaceutically active compounds in water samples using solid-phase extraction coupled with ultra-performance liquid chromatography-tandem mass spectrometry

Rapid Determination of Tetracyclines in Drinking and Environmental Waters Using Fully Automatic Solid-Phase Extraction with Ultra-Performance Liquid Chromatography-Tandem Mass Spectrometry

The abuse and irrational use of tetracyclines (TCs) in human medicine and animal husbandry has become a serious concern, affecting the ecological environment and human health. The aim of this study was to develop a sensitive and selective method using fully automatic solid-phase extraction coupled with ultra-performance liquid chromatography-tandem mass spectrometry for the determination of twelve TCs in water. Four isotope-labeled internal standards for TCs were used to correct matrix effects. Several parameters affecting extraction efficiency were systematically optimized, and the optimum experimental conditions found were 1.0 L water sample with 0.5 g/L Na2EDTA (pH 3.0) extracted and enriched by CNW HLB cartridge and eluted by 4 mL of acetone:methanol (v/v, 1:1). The enrichment factors were up to 798-1059 but only requiring about 60 min per six samples. Under the optimized conditions, the linearity of the method ranged from 0.2 to 100 μg/L for 12 TCs, the detection limits were as low as 0.01-0.15 ng/L, and the recoveries were in the range of 70%-118%, with relative standard deviations less than 15%. The developed method can be successfully utilized for the determination of 12 TCs in pure water, tap water, river water, and mariculture seawater. In summary, three and six TCs were detected in river water and mariculture seawater, respectively, with total concentrations of 0.074-0.520 ng/L (mean 0.248 ng/L) and 0.792-58.369 ng/L (12.629 ng/L), respectively. Tetracycline (TC) and oxytetracycline (OTC) were the dominant TCs in river water, while doxytetracycline (DXC) and OTC were dominant in mariculture seawater.

Efficacy of new generation biosorbents for the sustainable treatment of antibiotic residues and antibiotic resistance genes from polluted waste effluent

Antimicrobials are frequently used in both humans and animals for the treatment of bacterially-generated illnesses. Antibiotic usage has increased for more than 40% from last 15 years globally per day in both human populations and farm animals leading to the large-scale discharge of antibiotic residues into wastewater. Most antibiotics end up in sewer systems, either directly from industry or healthcare systems, or indirectly from humans and animals after being partially metabolized or broken down following consumption. To prevent additional antibiotic compound pollution, which eventually impacts on the spread of antibiotic resistance, it is crucial to remove antibiotic residues from wastewater. Antibiotic accumulation and antibiotic resistance genes cannot be effectively and efficiently eliminated by conventional sewage treatment plants. Because of their high energy requirements and operating costs, many of the available technologies are not feasible. However, the biosorption method, which uses low-cost biomass as the biosorbent, is an alternative technique to potentially address these problems. An extensive literature survey focusing on developments in the field was conducted using English language electronic databases, such as PubMed, Google Scholar, Pubag, Google books, and ResearchGate, to understand the relative value of the available antibiotic removal methods. The predominant techniques for eliminating antibiotic residues from wastewater were categorized and defined by example. The approaches were contrasted, and the benefits and drawbacks were highlighted. Additionally, we included a few antibiotics whose removal from aquatic environments has been the subject of extensive research. Lastly, a few representative publications were identified that provide specific information on the removal rates attained by each technique. This review provides evidence that biosorption of antibiotic residues from biological waste using natural biosorbent materials is an affordable and effective technique for eliminating antibiotic residues from wastewater.

An Automated Solid-Phase Extraction-UPLC-MS/MS Method for Simultaneous Determination of Sulfonamide Antimicrobials in Environmental Water

The large-scale use of sulfonamide antimicrobials in human and veterinary medicine has seriously endangered the ecological environment and human health. The objective of this study was to develop and validate a simple and robust method for the simultaneous determination of seventeen sulfonamides in water using ultra-high performance liquid chromatography-tandem mass spectrometry coupled with fully automated solid-phase extraction. Seventeen isotope-labeled internal standards for sulfonamides were used to correct matrix effects. Several parameters affecting extraction efficiency were systematically optimized, and the enrichment factors were up to 982-1033 and only requiring about 60 min per six samples. Under the optimized conditions, this method manifested good linearity (0.05-100 μg/L), high sensitivity (detection limits: 0.01-0.05 ng/L), and satisfactory recoveries (79-118%) with acceptable relative standard deviations (0.3-14.5%, n = 5). The developed method can be successfully utilized for the determination of 17 sulfonamides in pure water, tap water, river water, and seawater. In total, six and seven sulfonamides were detected in river water and seawater, respectively, with a total concentration of 8.157-29.676 ng/L and 1.683-36.955 ng/L, respectively, and sulfamethoxazole was the predominant congener.

Pilot-scale removal of persistent and mobile organic substances in granular activated carbon filters and experimental predictability at lab-scale

Present knowledge about the fate of persistent and mobile (PM) substances in drinking water treatment is limited. Hence, this study assesses the potential of fixed-bed granular activated carbon (GAC) filters to fill the treatment gap for PM substances and the elimination predictability from lab-scale experiments. Two parallel pilot filters (GAC bed height 2 m, diameter 15 cm) with different GAC were operated for 1.5 years (ca. 47,000 BV throughput) alongside rapid small-scale column tests (RSSCT) designed based on the proportional diffusivity (PD) and the constant diffusivity (CD) approaches. Background dissolved organic matter (DOM) and a set of 17 target substances were investigated, among them 2-acrylamido-2-methylpropane sulfonate (AAMPS), adamantan-1-amine (ATA), melamine (MEL) and trifluoromethanesulfonic acid (TFMSA). Nine substances were predominantly present in the drinking water used as pilot filter influent (frequencies of detection above 80 %, median concentrations 0.003-1.868 μg/L) and their breakthrough behaviors could be observed: TFMSA was not retained at all, four substances including AAMPS and ATA reached complete breakthrough below 20,000 BV, three compounds were partially retained until the end of operation and oxypurinol was retained completely. The comparable PM candidate and DOM removal performances of both GAC aligns with their very similar surface characteristics and elemental compositions. The agreement of results between RSSCT with the pilot-scale filters were substance specific and no superior RSSCT design could be identified. However, CD-RSSCT provide a conservative removal prediction for most studied compounds. MEL adsorption was significantly underestimated by both RSSCT designs. Using the criterion of a carbon usage rate (with respect to 50 % breakthrough) below 25 mg_GAC/L_water for an economic retention by fixed-bed GAC filters, five (out of nine) substances met the requirement.

Determination of quinolone antibiotics in environmental water using automatic solid-phase extraction and isotope dilution ultra-performance liquid chromatography tandem mass spectrometry

The widespread use of quinolones in humans and animals has become a major threat to public health. In this study, a simple, rapid, sensitive, and high throughput method based on automatic solid-phase extraction and isotope dilution ultra-performance liquid chromatography tandem mass spectrometry was described for the determination of trace quinolones in environmental water. The proposed automated solid-phase extraction method was initially optimized, and the optimum experimental conditions found were 1 L water sample with 0.5 g/L Na₂EDTA (pH 3) extracted and enriched by CNW Poly-Sery HLB cartridge at a flow rate of 50 mL/min and eluted by 8 mL of methanol. The linearity of the method ranged from 0.05 to 100 μg/L for 15 quinolones, with correlation coefficients ranging from 0.9993 to 0.9999. The limits of detection were in the low ng/L level, ranging from 0.005 to 0.051 ng/L. Finally, the optimized method was applied for determining trace levels of 15 quinolones in Wahaha pure water, tap water, river water, and seawater samples with good recoveries of 93 %-119 % and satisfactory relative standard deviations of 0.1 %-13.9 %. Fourteen quinolones were detected, and ofloxacin was the predominant congener in river water and seawater.

Electrospun chitosan/polyethylene oxide nanofibers mat loaded with copper (II) as a new sensor for colorimetric detection of tetracycline

Using electrospun chitosan/polyethylene oxide nanofibers mat (CS/PEO NFM) as carrier, Cu@CS/PEO NFM, a new tetracycline (TC) solid-state colorimetric sensor, were simply prepared by directly immobilizing Cu²⁺ on surface of CS/PEO NFM. After immersing in TC solutions, Cu@CS/PEO NFM can display visible color changes to the naked eye within 5.0 min, and the TC concentration-dependent color changes can also be quantitatively analyzed with a smartphone. Because Cu²⁺ can enhance the adsorption of CS/PEO NFM for TC, Cu@CS/PEO NFM possess a more sensitive response ability to TC, ensuring that the colorimetric sensing detection will not be interfered by other coexisting drugs. Due to the reversible combination of chitosan and Cu²⁺, the colorimetric sensing ability of Cu@CS/PEO NFM can be regenerated even after being reused at least 4 times. In addition, the naked eye detection limit of Cu@CS/PEO NFM-based colorimetric sensing is 65 μg kg^-1, which does not exceed the maximum residue limit in milk samples set by China (100 μg kg^-1). The obtained results fully indicated the practical application value of this method in preventing the hazard of TC residues.

Fully-automated SPE coupled to UHPLC-MS/MS method for multiresidue analysis of 26 trace antibiotics in environmental waters: SPE optimization and method validation

Achieving simultaneous determination of antibiotic multiresidues in environmental waters by solid phase extraction (SPE) coupled with ultra-high-performance liquid chromatography tandem mass spectrometry (UHPLC-MS/MS) with detection limits ≤ ng L^-1 is still a huge challenge. Moreover, the offline SPE procedure was performed manually, costly, and time-consuming, while the online SPE required precision pretreatment instruments that require highly-skilled personnel. In this paper, a fully automated SPE coupled with UHPLC-MS/MS method was developed for analysis of antibiotics (sulfonamides, quinolones, and macrolides) in water matrices. Sample preparation optimization included SPE materials and configuration (HLB disks), sample volume (500-1000 mL), and pH (pH = 3) with a flow rate at 2~5 mL min^-1, and an elution procedure with 2 × 6 mL methanol, and 2 × 6 mL acetone. Meanwhile, the parameters for UHPLC-MS/S detection of analytes were optimized, including LC retention time, and MS parameters. The instrumental limits of detection (LOD) and quantification (LOQ) of analytes ranged from 0.01-0.72 μg L^-1 and 0.05-2.39 μg L^-1, respectively, with satisfactory linear calibration (R² > 0.995) and precision (< 9.9%). Recoveries in spike samples ranged between 77.5-104.9% in pure water, 59.4-97.8% in surface water (SW), and 58.2-108.6% in wastewater effluent (WWE) with relative standard deviations ≤ 12.8%. The matrix effects observed for most analytes were suppression (0-28.1%) except for five analytes having presented enhancement (0-14.6 %) in SW or WWE. This method can basically meet the needs of trace antibiotic residues detection in waters, with examples of concentrations of detected antibiotics being lower than LOQ (LLQ) -94.47 ng L^-1 in WWEs and LLQ-15.47 ng L^-1 in SW in the lower reaches of the Yangtze River Basin.

Critical review on hazardous pollutants in water environment: Occurrence, monitoring, fate, removal technologies and risk assessment

Water is required for the existence of all living things. Water pollution has grown significantly, over the decades and now it has developed as a serious worldwide problem. The presence and persistence of Hazardous pollutants such as dyes, pharmaceuticals and personal care products, heavy metals, fertilizer and pesticides and their transformed products are the matter of serious environmental and health concerns. A variety of approaches have been tried to clean up water and maintain water quality. The type of pollutants present in the water determines the bulk of technological solutions. The main objective of this article was to review the occurrences and fate of hazardous contaminants (dyes, pharmaceuticals and personal care products, heavy metals, and pesticides) found in wastewater effluents. These effluents mingle with other streams of water and that are utilized for a variety of reasons such as irrigation and other domestic activities that is further complicating the issue. It also discussed traditional treatment approaches as well as current advances in hazardous pollutants removal employing graphite oxides, carbon nanotubes, metal organic structures, magnetic nano composites, and other innovative forms of useable materials. It also discussed the identification and quantification of harmful pollutants using various approaches, as well as current advancements. Finally, a risk assessment of hazardous pollutants in water is provided in terms of the human health and the environment. This data is anticipated to serve as a foundation for future improvements in hazardous pollutant risk assessment. Furthermore, future studies on hazardous pollutants must not only emphasize on the parent chemicals, as well as on their possible breakdown products in various media.

Filling the knowledge gap: A suspect screening study for 1310 potentially persistent and mobile chemicals with SFC- and HILIC-HRMS in two German river systems

Persistent and mobile chemicals (PM chemicals) were searched for in surface waters by hydrophilic interaction liquid chromatography (HILIC) and supercritical fluid chromatography (SFC), both coupled to high resolution mass spectrometry (HRMS). A suspect screening was performed using a newly compiled list of 1310 potential PM chemicals to the data of 11 surface water samples from two river systems. In total, 64 compounds were identified by this approach. The overlap between HILIC- and SFC-HRMS was limited (31 compounds), confirming the complementarity of the two methods used. The identified PM candidates are characterized by a high polarity (median logD -0.4 at pH 7.5), a low molecular weight (median 187 g/mol), are mostly ionic (54 compounds) and contain a large number of heteroatoms (one per four carbons on average). Among the most frequently detected novel or yet scarcely investigated water contaminants were cyanoguanidine (11/11 samples), adamantan-1-amine (10/11), trifluoromethanesulfonate (9/11), 2-acrylamido-2-methylpropanesulfonate (10/11), and the inorganic anions hexafluorophosphate (11/11) and tetrafluoroborate (10/11). 31% of the identified suspects are mainly used in ionic liquids, a chemically diverse group of industrial chemicals with numerous applications that is so far rarely studied for their occurrence in the environment. Prioritization of the findings of PM candidates is hampered by the apparent lack of toxicity data. Hence, precautionary principles and minimization approaches should be applied for the risk assessment and risk management of these substances. The large share of novel water contaminants among these findings of the suspect screening indicates that the universe of PM chemicals present in the environment has so far only scarcely been explored. Dedicated analytical methods and screening lists appear essential to close the analytical gap for PM compounds.

Multiresidue antibiotic-metabolite quantification method using ultra-performance liquid chromatography coupled with tandem mass spectrometry for environmental and public exposure estimation

This manuscript describes a new multiresidue method utilising ultra-performance liquid chromatography tandem mass spectrometry (UPLC-MS/MS) via multiple reaction monitoring (MRM), for the identification and quantification of 58 antibiotics and their 26 metabolites, in various solid and liquid environmental matrices. The method was designed with a ‘one health’ approach in mind requiring multidisciplinary and multisectoral collaborative efforts. It enables comprehensive evaluation of antibiotic usage in surveyed communities via wastewater-based epidemiology, as well as allowing for the assessment of potential environmental impacts. The instrumental performance was very good, demonstrating linearity up to 3000 μg L⁻¹, and high accuracy and precision. The method accuracy in several compounds was significantly improved by dividing calibration curves into separate ranges. This was accompanied by applying a weighting factor (1/x). Microwave-assisted and/or solid-phase extraction of analytes from liquid and solid matrices provided good recoveries for most compounds, with only a few analytes underperforming. Method quantification limits were determined as low as 0.017 ng L⁻¹ in river water, 0.044 ng L⁻¹ in wastewater, 0.008 ng g⁻¹ in river sediment, and 0.009 ng g⁻¹ in suspended solids. Overall, the method was successfully validated for the quantification of 64 analytes extracted from aqueous samples, and 45 from solids. The analytes that underperformed are considered on a semi-quantitative basis, including aminoglycosides and carbapenems. The method was applied to both solid and liquid environmental matrices, whereby several antibiotics and their metabolites were quantified. The most notable antibiotic-metabolite pairs are three sulfonamides and their N-acetyl metabolites; four macrolides/lincomycins and their N-desmethyl metabolites; and five quinolone metabolites.

Determination and dietary intake risk assessment of 14 pesticide residues in apples of China

The presence of pesticide residues in apples raises serious health concerns. In this study, a novel, sensitive, high-performance method was developed to simultaneously analyze the residues of 14 pesticides in apples using modified QuEChERS sample pretreatment coupled with ultra-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS). The optimized purification procedure demonstrated satisfactory recovery and precision for all the tested pesticides. The limits of detection (LOD) and quantification (LOQ) values of 14 pesticides in the apple matrix ranged from 0.03 μg/kg to 0.3 μg/kg and 0.1 μg/kg to 1.0 μg/kg, respectively. The proposed method detected six pesticides in the apple samples collected from 20 counties in China's major apple-producing regions. Furthermore, the risk quotient (RQ, %) of the detected pesticides was evaluated by the national estimated acceptable daily intake. The RQs of six pesticides in Chinese people of different age groups were less than 100%.

Electrooxidation of tetracycline antibiotic demeclocycline at unmodified boron-doped diamond electrode and its enhancement determination in surfactant-containing media

In this paper, for the first time, the study of voltammetric determination of tetracycline antibiotic demeclocycline was conducted. The oxidation of compound was investigated using a commercially available boron-doped diamond electrode pretreated electrochemically (anodic and subsequent cathodic). Addition of anionic surfactant, sodium dodecylsulfate (SDS) and cationic surfactant, cetyltrimethylammonium bromide (CTAB) to the demeclocycline-containing electrolyte solution at pH 2.0 and 9.0, respectively, was found to improve the sensitivity of the stripping voltammetric measurements. Employing square-wave stripping mode (after 30 s accumulation at open-circuit condition) in Britton-Robinson buffer, the limits of detection were found to be 1.17 μg mL^-1 (2.3 × 10^-6 M) for 4 × 10^-4 SDS-containing buffer solution at pH 2, and 0.24 μg mL^-1 (4.8 × 10^-7 M) for 1 × 10^-4 CTAB-containing buffer solution at pH 9.0. The feasibility of the developed approach for the quantification of demeclocycline was tested in urine samples.