Green Synthesis of Photocatalytic TiO2 Nanoparticles for Potential Application in Photochemical Degradation of Ornidazole

Light-driven photocatalysis as an effective tool for degradation of antibiotics

Antibiotic contamination has become a severe issue and a dangerous concern to the environment because of large release of antibiotic effluent into terrestrial and aquatic ecosystems. To try and solve these issues, a plethora of research on antibiotic withdrawal has been carried out. Recently photocatalysis has received tremendous attention due to its ability to remove antibiotics from aqueous solutions in a cost-effective and environmentally friendly manner with few drawbacks compared to traditional photocatalysts. Considerable attention has been focused on developing advanced visible light-driven photocatalysts in order to address these problems. This review provides an overview of recent developments in the field of photocatalytic degradation of antibiotics, including the doping of metals and non-metals into ultraviolet light-driven photocatalysts, the formation of new semiconductor photocatalysts, the advancement of heterojunction photocatalysts, and the building of surface plasmon resonance-enhanced photocatalytic systems.

Kinetic constants and transformation products of ornidazole during ozonation

Ornidazole (ONZ), a nitroimidazole antibiotic detected in water bodies, may negatively impact the aquatic ecosystem. Its reaction kinetics during ozonation which is a feasible and applicable technology to control the contamination of emerging contaminants, however, has not been reported in literature. In this study, we measured the apparent second-order kinetic constant of ONZ with ozone molecules via the excessive ozone method and the competing method which led to an average value of 103.8 ± 2.7 M-1 s-1 at pH 7. The apparent second-order kinetic constant of ONZ with HO• was calculated to be 4.65 × 109 M-1 s-1 with the concept of Rct measured via para-chlorobenzoic acid as a probe. The transformation products (TPs) of ONZ during ozonation at pH 3 and pH 11 were separately analyzed with HPLC-MS/MS and some unique products were found at pH 11, reflecting the influence of HO•. The toxicity of individual TPs was predicted with the tool of T.E.S.T. It was found that 62% of 21 identified TPs could be more toxic than ONZ in terms of at least one acute toxicity endpoint, including chlorinated amines and N-oxides. The analysis with a respirometer further revealed that the toxicity of mixing TPs generated at HO• rich conditions was slightly lower than O3 dominated conditions. In general, this study provides the basic kinetic data for designing ozonation processes to eliminate ONZ and the important reference for understanding the toxicity evolution of ONZ during ozonation.

Synthesis and characterization of titanium dioxide nanoparticles from Bacillus subtilis MTCC 8322 and its application for the removal of methylene blue and orange G dyes under UV light and visible light

Over the last decade there has been a huge increase in the green synthesis of nanoparticles. Moreover, there is a continuous increase in harnessing the potential of microorganisms for the development of efficient and biocompatible nanoparticles around the globe. In the present research work, investigators have synthesized TiO2 NPs by harnessing the potential of Bacillus subtilis MTCC 8322 (Gram-positive) bacteria. The formation and confirmation of the TiO2 NPs synthesized by bacteria were carried out by using UV-Vis spectroscopy, Fourier transforms infrared (FT-IR), X-ray diffraction (XRD), scanning electron microscope (SEM), and energy dispersive X-ray spectroscopy (EDX/EDS). The size of the synthesized TiO2 NPs was 80-120 nm which was spherical to irregular in shape as revealed by SEM. FTIR showed the characteristic bands of Ti-O in the range of 400-550 cm-1 and 924 cm-1 while the band at 2930 cm-1 confirmed the association of bacterial biomolecules with the synthesized TiO2 NPs. XRD showed two major peaks; 27.5° (rutile phase) and 45.6° (anatase phase) for the synthesized TiO2 NPs. Finally, the potential of the synthesized TiO2 NPs was assessed as an antibacterial agent and photocatalyst. The remediation of Methylene blue (MB) and Orange G (OG) dyes was carried out under UV- light and visible light for a contact time of 150-240 min respectively. The removal efficiency for 100 ppm MB dye was 25.75% and for OG dye was 72.24% under UV light, while in visible light, the maximum removal percentage for MB and OG dye was 98.85% and 80.43% respectively at 90 min. Moreover, a kinetic study and adsorption isotherm study were carried out for the removal of both dyes, where the pseudo-first-order for MB dye is 263.269 and 475554.176 mg/g for OG dye. The pseudo-second-order kinetics for MB and OG dye were 188.679 and 1666.667 mg/g respectively. In addition to this, the antibacterial activity of TiO2 NPs was assessed against Bacillus subtilis MTCC 8322 (Gram-positive) and Escherichia coli MTCC 8933 (Gram-negative) where the maximum zone of inhibition in Bacillus subtilis MTCC 8322 was about 12 mm, and for E. coli 16 mm.

Heterogeneous photocatalytic degradation of antiviral drug didanosine mediated by rose bengal and TiO2 nanoparticles

There is a great concern among the researcher to remove the problem of the persistent organic pollutants in wastewater. Pharmaceutical agrochemical and personal care products are generally considered Persistent organic pollutants. Therefore, it is a matter of concern to develop new techniques how to remove these pollutants safely at low cost. This study mainly focuses on the commonly used antiviral drug didanosine and one most commonly used dye rose bengal. In this study, an organic dye rose bengal and TiO2 nanoparticles have been used in combination with UV light to achieve the photodegradation of selected pharmaceutical products and the dye was also degraded by using TiO2 Nanoparticles. The formation of three oxidation products was detected by using a very popular separation technique thin layer and column chromatography. The isolated photoproduct was characterized by using advanced characterization techniques like FTIR (Fourier transform infrared spectroscopy), UV Spectroscopy, and Proton and 13C NMR (Nuclear Magnetic Resonance spectroscopy). The role of singlet oxygen as an active species in this reaction was confirmed by using D2O as a reaction medium. The role of singlet oxygen in this photochemical reaction was also established by the addition of sodium azide. The TiO2 nanophotocatalyst efficiently degrade the didanosine and rose bengal in the presence of the UV light. In the TiO2-induced photocatalytic degradation of didanosine and dyes, the hydroxyl and superoxide radical anion play a prominent role. The finding of this manuscript is very useful to develop an efficient low-cost method for the treatment of wastewater contaminated by antiviral drugs, similar pharmaceutical products and dyes. This study was also very helpful to establish a plausible mechanism behind the phototoxicity of the didanosine.

Low-temperature molten-salt synthesis of Co3O4 nanoparticles grown on MXene can rapidly remove ornidazole via peroxymonosulfate activation

We further developed previous work on MXene materials prepared using molten salt methodology. We substituted single, with mixed salts, and reduced the melting point from >724 °C to <360 °C. Cobalt (Co) compounds were simultaneously etched and doped while the MXene material was created using various techniques in which Co compounds occur as Co3O4. The synthesized Co3O4/MXene compound was used as a peroxymonosulfate (PMS) activator that would generate free radicals to degrade antibiotic ornidazole (ONZ). Under optimal conditions, almost 100% of ONZ (30 mg/L) was degraded within 10 min. The Co3O4/MXene + PMS system efficiently degraded ONZ in natural water bodies, and had a broad pH adaptation range (4-11), and strong anion anti-interference. We investigated how the four active substances were generated using radical quenching and electron paramagnetic resonance (EPR) spectroscopy. We identified 12 ONZ intermediates by liquid chromatography-mass spectrometry and propose a plausible degradative mechanism.

Green synthesis of TiO2 for furfural production by photohydrolysis of tortilla manufacturing waste

Corn nixtamalization generates a waste byproduct that requires diverse environmental preservation measures depending on the country. Such measures could include catalytic and advanced oxidation processes. This study aims to exploit the hemicellulose within the nejayote (32.5%) to create added value chemicals such as furfural using photocatalytic hydrolysis. In the present work, titania (TiO2) nanoparticles (NPs) were greenly synthesized using Ricinus Communis (RC), Moringa Oleifera (MO) or Bougainvillea Spectabilis (BS) plant extracts. Obtained nanoparticles were characterized using XRD, SEM, EDS, BET, XPS and UV-vis techniques. Furthermore, the photocatalytic performance of the obtained samples was evaluated in the furfural production from nejayote. Furfural yield reached 44% in 30 min using the BS synthesized material, which is 1.6 × the yield obtained by the material synthesized with MO extract (26.4% at 45 min) and 6 × the yield obtained by the material obtained with RC (7.2% at 90 min). Such results have not been reported before in the literature and could be the groundwork for novel waste treatments in the tortilla-making industry.

Acmella oleracea induced nanostructured Ca2Fe2O5 for evaluation of photo catalytic degradation of cardiovascular drugs and bio toxicity

Biosynthesis of nanoparticles is increasingly becoming popular due to the demand for sustainable technologies worldwide. In the present investigation, Acmella oleracea plant extract fuelled combustion technique followed by calcination at 600 °C was adopted to prepare nanocrystalline Ca₂Fe₂O₅. The prepared nano compound was characterised using X-ray powder diffraction (XRD), scanning electron microscopy (SEM), Ultra Violet (UV) spectroscopy, Infrared (IR) spectroscopy and its role was assessed for photocatalytic pollutant degradation along with bactericidal action in the concentration range of 1 μg/mL to 320 μg/mL. The photocatalytic degradation efficiency of pollutant drugs Clopidogrel Bisulphate and Asprin used for cardiovascular disorders is around 80% with 10 mg/L photocatalyst. The results showed that the photocatalytic activity increased with rising pH from 4, to 10, along with a significant antibacterial action against Enterococcus faecalis bacteria and a slight cytotoxic effect at high concentrations. The antibacterial property was reinforced by Minimum inhibitory concentrations (MIC) and Minimum bactericidal concentrations (MBC) studies with an average value of 0.103 at 600 nm which was further proved by significant anti-biofilm activeness. Adhesion tests in conjunction with cryogenic-scanning electron microscopy displayed a morphological change through agglomeration that caused an expansion in nano particles from 181 nm to 223.6 nm due to internalization followed by inactivation of bacteria. In addition, the non-toxicity of nano Ca₂Fe₂O₅ was confirmed by subtle cytological changes in microscopic images of Allium Cepa root cells in the concentration range 0.01-100 μg/mL and a slight inhibition in HeLa cell proliferation indicated by IC₅₀ value of 170.94 μg/mL. In total, the current investigation for the first time reveals the application of bio based synthesis of Nano Ca₂Fe₂O₅ to new possibilities in bioremediation namely degrading cardiovascular pharmaceutical pollutants, endodontic antibacterial action and cytological activity.

Green synthesis of nanoparticles using botanicals and their application in management of fungal phytopathogens: a review

Green synthesis of nanoparticles is an emerging aspect in plant disease management that blends nanotechnology and plant-derived ingredients to produce a biocontrol formulation. Different physical and chemical processes employed in the synthesis of nanoparticles are polluting, expensive, and also release hazardous by- products. The range of secondary metabolites present in plants makes them efficient reducing and stabilizing agent during the synthesis process. These metabolites serve a vital role in plant defense against the invasion of phytopathogens including fungi, bacteria, viruses, insect pests, etc. The plant metabolites, such as sugars, terpenoids, polyphenols, alkaloids, phenolic acids, and proteins, have been shown to be crucial in the reduction of metal ions into nanoparticles. In green synthesis of nanoparticles, the plant extracts are used as potential reducing and capping. This also restricts the formation of clusters or aggregates and improves the colloidal stability. The nanoparticles exhibit excellent antimycotic against a variety of phytopathogens and are very efficient in managing plant diseases. The aim of this review is to highlight plants, phytochemicals exhibiting antifungal properties, green synthesis of nanoparticles using plant material and their antimycotic activity.

Waste to catalyst: Role of agricultural waste in water and wastewater treatment

Presently, owing to the rapid development of industrialization and urbanization activities, a huge quantity of wastewater is generated that contain toxic chemical and heavy metals, imposing higher environmental jeopardies and affecting the life of living well-being and the economy of the counties, if not treated appropriately. Subsequently, the advancement in sustainable cost-effective wastewater treatment technology has attracted more attention from policymakers, legislators, and scientific communities. Therefore, the current review intends to highlight the recent development and applications of biochars and/or green nanoparticles (NPs) produced from agricultural waste via green routes in removing the refractory pollutants from water and wastewater. This review also highlights the contemporary application and mechanism of biochar-supported advanced oxidation processes (AOPs) for the removal of organic pollutants in water and wastewater. Although, the fabrication and application of agriculture waste-derived biochar and NPs are considered a greener approach, nevertheless, before scaling up production and application, its toxicological and life-cycle challenges must be taken into account. Furthermore, future efforts should be carried out towards process engineering to enhance the performance of green catalysts to improve the economy of the process.

Pharmaceutical residues: One of the significant problems in achieving 'clean water for all' and its solution

With the rapid emergence of various metabolic and multiple-drug-resistant infectious diseases, new pharmaceuticals are continuously being introduced in the market. The excess production and use of pharmaceuticals and their untreated/unmetabolized release in the environment cause the contamination of aquatic ecosystem, and thus, compromise the environment and human-health. The present review provides insights into the classification, sources, occurrence, harmful impacts, and existing technologies to curb these problems. A comprehensive detail of various biological and nanotechnological strategies for the removal of pharmaceutical residues from water is critically discussed focusing on their efficiencies, and current limitations to design improved-technologies for their lab-to-field applications. Furthermore, the review highlights and suggests the scope of integrated bionanotechnological methods for enhanced removal of pharmaceutical residues from water to fulfill the United Nations Sustainable Development Goal (UN-SDG) for providing clean potable water for all.

Green Synthesis of Metal and Metal Oxide Nanoparticles Using Different Plants’ Parts for Antimicrobial Activity and Anticancer Activity: A Review Article

Nanotechnology emerged as a scientific innovation in the 21st century. Metallic nanoparticles (metal or metal oxide nanoparticles) have attained remarkable popularity due to their interesting biological, physical, chemical, magnetic, and optical properties. Metal-based nanoparticles can be prepared by utilizing different biological, physical, and chemical methods. The biological method is preferred as it provides a green, simple, facile, ecofriendly, rapid, and cost-effective route for the green synthesis of nanoparticles. Plants have complex phytochemical constituents such as carbohydrates, amino acids, phenolics, flavonoids, terpenoids, and proteins, which can behave as reducing and stabilizing agents. However, the mechanism of green synthesis by using plants is still highly debatable. In this report, we summarized basic principles or mechanisms of green synthesis especially for metal or metal oxide (i.e., ZnO, Au, Ag, and TiO2, Fe, Fe2O3, Cu, CuO, Co) nanoparticles. Finally, we explored the medical applications of plant-based nanoparticles in terms of antibacterial, antifungal, and anticancer activity.

Green Synthesis and Applications of ZnO and TiO2 Nanostructures

Over the last two decades, oxide nanostructures have been continuously evaluated and used in many technological applications. The advancement of the controlled synthesis approach to design desired morphology is a fundamental key to the discipline of material science and nanotechnology. These nanostructures can be prepared via different physical and chemical methods; however, a green and ecofriendly synthesis approach is a promising way to produce these nanostructures with desired properties with less risk of hazardous chemicals. In this regard, ZnO and TiO2 nanostructures are prominent candidates for various applications. Moreover, they are more efficient, non-toxic, and cost-effective. This review mainly focuses on the recent state-of-the-art advancements in the green synthesis approach for ZnO and TiO2 nanostructures and their applications. The first section summarizes the green synthesis approach to synthesize ZnO and TiO2 nanostructures via different routes such as solvothermal, hydrothermal, co-precipitation, and sol-gel using biological systems that are based on the principles of green chemistry. The second section demonstrates the application of ZnO and TiO2 nanostructures. The review also discusses the problems and future perspectives of green synthesis methods and the related issues posed and overlooked by the scientific community on the green approach to nanostructure oxides.