Microwave-assisted derivatization procedures for gas chromatography/mass spectrometry analysis

Evaluation of polypropylene microporous membranes as extraction devices for determination of carcinogenic aromatic amines in smoker urine by GC-MS/MS

Exposure to tobacco smoke is highly correlated to the incidence of different types of cancer due to various carcinogenic compounds present in such smoke. Aromatic amines, such as 1-naphthylamine (1-NA) and 2-naphthylamine (2-NA), are produced in tobacco burning and are linked to bladder cancer. Miniaturized solid phase extraction techniques, such as microporous membrane solid phase extraction (MMSPE), have shown potential for the extraction of aromatic compounds. In this study, a bioanalytical method for the determination of 1-NA and 2-NA in human urine was developed using polypropylene microporous membranes as a sorptive phase for MMSPE. Urine samples were hydrolyzed with HCl for 1 h at 80 °C, after which pH was adjusted to 10. Ultrasound-assisted MMSPE procedure was optimized by factorial design as follows. To each sample, 750 µL of methanol was added, and ultrasound-assisted MMSPE was conducted for 1 h with four devices containing seven 2 mm polypropylene membrane segments. After extraction, the segments were transferred to 400 µL of hexane, and desorption was conducted for 30 min. Extracts were submitted to a simple and fast microwave-assisted derivatization procedure, by the addition of 10 µL of PFPA and heating at 480 W for 3 min, followed by clean-up with phosphate buffer pH 8.0 and GC-MS/MS analysis. Adequate linearity was obtained for both analytes in a range from 25 to 500 µg L-1, while the multiple reaction monitoring approach provided satisfactory selectivity and specificity. Intra-day (n = 6) and inter-day (n = 5) precision and accuracy were satisfactory, below 15 % and between 85 and 115 %, respectively. Recovery rates found were 91.9 and 58.4 % for 1-NA and 2-NA, respectively, with adequate precision. 1-NA was found in first-hand smokers' urine samples in a concentration range from 20.98 to 89.09 µg in 24 h, while it could be detected in second-hand smoker's urine samples, and 2-NA detected in all first and second-hand smokers' urine samples. The proposed method expands the applicability of low cost MMSPE devices to aromatic amines and biological fluids.

Use of Trifluoro-Acetate Derivatives for GC-MS and GC-MS/MS Quantification of Trace Amounts of Stera-3β,5α,6β-Triols (Tracers of Δ5-Sterol Autoxidation) in Environmental Samples

Stera-3β,5α,6β-triols make useful tracers of the autoxidation of Δ⁵-sterols. These compounds are generally analyzed using gas chromatography-mass spectrometry (GC-MS) after silylation. Unfortunately, the 5α hydroxyl groups of these compounds, which are not derivatized by conventional silylation reagents, substantially alter the chromatographic properties of these derivatives, thus ruling out firm quantification of trace amounts. In this work, we developed a derivatization method (trifluoroacetylation) that enables derivatization of the three hydroxyl groups of 3β,5α,6β-steratriols. The derivatives thus formed present several advantages over silyl ethers: (i) better stability, (ii) shorter retention times, (iii) better chromatographic properties and (iv) mass spectra featuring specific ions or transitions that enable very low limits of detection in selected ion monitoring (SIM) and multiple reaction monitoring (MRM) modes. This method, validated with cholesta-3β,5α,6β-triol, was applied to several environmental samples (desert dusts, marine sediments and particulate matter) and was able to quantify trace amounts of 3β,5α,6β-steratriols corresponding to several sterols: not only classical monounsaturated sterols (e.g., cholesterol, campesterol and sitosterol) but also, and for the first time, di-unsaturated sterols (e.g., stigmasterol, dehydrocholesterol and brassicasterol).

A sensitive, robust method for determining natural and synthetic hormones in surface and wastewaters by continuous solid-phase extraction-gas chromatography-mass spectrometry

Over recent decades, steroidal estrogens have become an emerging and very serious issue as they pose a serious threat to living organisms, soil, plants, and water resources in general. Estrogens have therefore been the subject of considerable scientific attention in order to develop new methodologies for its determination, being able of detecting them at very low concentrations. Those procedures minimize or eliminate the consumption of organic solvents and reagents that may be incompatible with the environment. In this respect, we developed a sensitive, selective method for the simultaneous determination of thirteen natural and synthetic hormones present at the nanogram-per-liter level in various types of water by using continuous solid-phase extraction in combination with gas chromatography and mass spectrometry (GC-MS). The target analytes were preferentially sorbed on an Oasis HLB sorbent column (80 mg) and eluted with acetone (600 µL) for derivatization with a mixture of 70 µL of N,O-bis(trimethylsilyl) trifluoroacetamide and trimethylchlorosilane and 35 µL of petroleum ether in a household microwave oven at 200 W for 4 min. Under optimum conditions, the ensuing method exhibited good linearity (r ≥ 0.998), good precision (RSD ≤ 7%), high recoveries (92-103%), and low detection limits (0.01-0.3 ng L-1). The method outperforms existing alternatives in robustness, sensitivity, throughput, flexibility-it allows both estrogens, progestogens, and androgens to be determined simultaneously-and compliance with the principles of Green Chemistry. It was successfully used to analyze various types of water samples (mineral, tap, well, pond, swimming pool, river, and waste) that were found to contain four estrogens (estrone, 17β-estradiol, 17α-ethinylestradiol, and hexestrol), two progestogens (testosterone, dihydrotestosterone), and one progestogen (progesterone) at concentrations ranging from 3.0 to 110 ng L-1.

A simple and fast method for metabolomic analysis by gas liquid chromatography-mass spectrometry

INTRODUCTION

The metabolomic profile is an essential tool for understanding the physiological processes of biological samples and their changes. In addition, it makes it possible to find new substances with industrial applications or use as drugs. As GC-MS is a very common tool for obtaining the metabolomic profile, a simple and fast method for sample preparation is required.

OBJECTIVES

The aim of this research was to develop a direct derivatization method for GC-MS to simplify the sample preparation process and apply it to a wide range of samples for non-targeted metabolomic analysis purposes.

METHODS

One pot combined esterification of carboxylic acids with methanol and silylation of the hydroxyl groups was achieved using a molar excess of chlorotrimethylsilane with respect to methanol in the presence of pyridine.

RESULTS

The metabolome profile obtained from different samples, such as bilberry and cherry cuticles, olive leaves, P. aeruginosa and E. coli bacteria, A. niger fungi and human sebum from the ceruminous gland, shows that the procedure allows the identification of a wide variety of metabolites. Aliphatic fatty acids, hydroxyfatty acids, phenolic and other aromatic compounds, fatty alcohols, fatty aldehydes dimethylacetals, hydrocarbons, terpenoids, sterols and carbohydrates were identified at different MSI levels using their mass spectra.

CONCLUSION

The metabolomic profile of different biological samples can be easily obtained by GC-MS using an efficient simultaneous esterification-silylation reaction. The derivatization method can be carried out in a short time in the same injection vial with a small amount of reagents.

Current Pretreatment/Cell Disruption and Extraction Methods Used to Improve Intracellular Lipid Recovery from Oleaginous Yeasts

The production of lipids from oleaginous yeasts involves several stages starting from cultivation and lipid accumulation, biomass harvesting and finally lipids extraction. However, the complex and relatively resistant cell wall of yeasts limits the full recovery of intracellular lipids and usually solvent extraction is not sufficient to effectively extract the lipid bodies. A pretreatment or cell disruption method is hence a prerequisite prior to solvent extraction. In general, there are no recovery methods that are equally efficient for different species of oleaginous yeasts. Each method adopts different mechanisms to disrupt cells and extract the lipids, thus a systematic evaluation is essential before choosing a particular method. In this review, mechanical (bead mill, ultrasonication, homogenization and microwave) and nonmechanical (enzyme, acid, base digestions and osmotic shock) methods that are currently used for the disruption or permeabilization of oleaginous yeasts are discussed based on their principle, application and feasibility, including their effects on the lipid yield. The attempts of using conventional and “green” solvents to selectively extract lipids are compared. Other emerging methods such as automated pressurized liquid extraction, supercritical fluid extraction and simultaneous in situ lipid recovery using capturing agents are also reviewed to facilitate the choice of more effective lipid recovery methods.

The role of gut microbiota (GM) and GM-related metabolites in diabetes and obesity. A review of analytical methods used to measure GM-related metabolites in fecal samples with a focus on metabolites' derivatization step

Disruption of gut microbiota (GM) composition is increasingly related to the pathogenesis of various metabolic diseases. Additionally, GM is responsible for the production and transformation of metabolites involved in the development of metabolic disorders, such as obesity and type 2 diabetes mellitus (T2DM). The current state of knowledge regarding the composition of GM and GM-related metabolites in relation to the progress and development of obesity and T2DM is presented in this review. To understand the relationships between GM-related metabolites and the development of metabolic disorders, their accurate qualitative and quantitative measurement in biological samples is needed. Feces represent a valuable biological matrix which composition may reflect the health status of the lower gastrointestinal tract and the whole organism. Mass spectrometry (MS), mainly in combination with gas chromatography (GC) or liquid chromatography (LC), is commonly used to measure fecal metabolites. However, profiling metabolites in such a complex matrix as feces is challenging from both analytical chemistry and biochemistry standpoints. Chemical derivatization is one of the most effective methods used to overcome these problems. In this review, we provide a comprehensive summary of the derivatization methods of GM-related metabolites prior to GC-MS or LC-MS analysis, which have been published in the last five years (2015-2020). Additionally, analytical methods used for the analysis of GM-related metabolites without the derivatization step are also presented.

Derivatization gas chromatography negative chemical ionization mass spectrometry for the analysis of trace organic pollutants and their metabolites in human biological samples

Gas chromatography negative chemical ionization mass spectrometry (GC-NCI-MS) is a preferred instrumental approach for the trace and ultra-trace analysis of various toxic organics and their metabolites in human biological fluids. Specifically, the method has played an important role in the highly sensitive and specific quantitative detection of persistent highly halogenated compounds in environmental matrices and biota during the past few decades. However, for the analysis of toxic metabolites with active hydrogen atoms, such as acids, alcohols, and phenolic compounds, from biological matrixes or organics without electronegative atoms or groups, a derivatization step is often needed prior to GC analysis. Such derivatization aims to change the properties of targets to improve their separation, increase their volatility, and enhance the sensitivity of instrumental detection. This review summarizes three derivatization strategies commonly used for GC methods, i.e., alkylation, silylation, and acylation, together with their application combined with GC-NCI-MS for the high sensitivity analysis of toxic organic metabolites in the human body. The advantages and disadvantages of each derivatization method and potential directions for future applications are discussed. Given the broad variety of applications as well as the compound-specific sensitivity for the ultra-trace analysis of target xenobiotics in human biological fluids, subsequent studies are required to develop convenient, faster derivatization procedures and reagents better suited for routine analysis. Graphical abstract.

A Novel Bioanalytical Method for the Determination of Opioids in Blood and Pericardial Fluid

Opioids are the drugs most commonly detected in overdose deaths and the second most consumed worldwide. An analytical methodology has been optimized and fully validated for the determination of codeine, morphine, 6-acetylmorphine, 6-acetylcodeine, oxycodone, oxymorphone and fentanyl in whole blood and pericardial fluid. The internal standards used were codeine-d3, morphine-d3, 6-acetylmorphine-d3 and fentanyl-d5. Before solid-phase extraction, volumes of 250 μL of blood and pericardial fluid were subjected to a protein precipitation (with 750 μL of ice-cold acetonitrile) and a microwave-induced oximation was performed using a solution of 1% aqueous hydroxylamine hydrochloride in phosphate-buffered saline (1:2, v/v). Finally, the dried extracts were further derivatized with a solution of n-methyl-n-(trimethylsilyl) trifluoroacetamide + 5% trimethylchlorosilane under microwave irradiation. The chromatographic analysis was carried out using gas chromatography–mass spectrometry operating in electron impact and selected ion monitoring mode. For all analytes, the method was linear between 5 and 1,000 ng/mL with determination coefficients (r2) >0.99. Depending on the analyte and matrix, the limit of detection varies between 3 and 4 ng/mL. Intra- and intermediate precision (<20%) and bias (±20%) were acceptable for all analytes in both matrices. The stability of the substances in the studied matrices was guaranteed, at least, 24 h in the autosampler, 4 h at room temperature and 30 days after three freeze/thaw cycles. This methodology was applied to real samples from the Laboratory of Chemistry and Forensic Toxicology, Centre Branch, of the National Institute of Legal Medicine and Forensic Sciences, Portugal.

Determination of New Psychoactive Substances in Whole Blood Using Microwave Fast Derivatization and Gas Chromatography/Mass Spectrometry

The production and consumption of new psychoactive substances (NPSs) has been raising a major concern worldwide. Due to easy access and available information, many NPSs continue to be synthesized with an alarming increase of those available to purchase, despite all the control efforts created. A new analytical method was developed and validated to determine a group of phenethylamines and synthetic cathinones: cathinone, flephedrone, buphedrone, 4-MTA, α-PVP, methylone, 2C-P, ethylone, pentylone, MDPV and bromo-dragonFLY in whole blood. A mixed-mode solid phase extraction was applied to 250 μL of sample, and the extracts were derivatized with fast microwave technique before being analyzed by gas chromatography-mass spectrometry (GC-MS). The validation procedure followed the Scientific Working Group for Forensic Toxicology (SWGTOX) guidelines with parameters that included selectivity, linearity, limits of detection and quantification, intra- and inter-day precision and accuracy, recoveries and stability. The method presented linearity between 5 and 500 ng/mL for cathinone, buphedrone, 4-MTA, methylone, 2C-P and bromo-dragonFLY, 10-500 ng/mL for flephedrone, ethylone, pentylone and MDPV, and 40-500 ng/mL for α-PVP, with determination coefficients above 0.99 for all analytes. Recoveries ranged between 70.3% and 116.6%, and regarding intra- and inter-day precision, the relative mean errors were typically lower than 8.6%. The method was successfully applied to over 100 authentic samples from the Laboratory of Chemistry and Forensic Toxicology, Centre Branch, of the National Institute of Legal Medicine and Forensic Sciences, Portugal.

Review of recent developments in GC-MS approaches to metabolomics-based research

BACKGROUND

Metabolomics aims to identify the changes in endogenous metabolites of biological systems in response to intrinsic and extrinsic factors. This is accomplished through untargeted, semi-targeted and targeted based approaches. Untargeted and semi-targeted methods are typically applied in hypothesis-generating investigations (aimed at measuring as many metabolites as possible), while targeted approaches analyze a relatively smaller subset of biochemically important and relevant metabolites. Regardless of approach, it is well recognized amongst the metabolomics community that gas chromatography-mass spectrometry (GC-MS) is one of the most efficient, reproducible and well used analytical platforms for metabolomics research. This is due to the robust, reproducible and selective nature of the technique, as well as the large number of well-established libraries of both commercial and 'in house' metabolite databases available.

AIM OF REVIEW

This review provides an overview of developments in GC-MS based metabolomics applications, with a focus on sample preparation and preservation techniques. A number of chemical derivatization (in-time, in-liner, offline and microwave assisted) techniques are also discussed. Electron impact ionization and a summary of alternate mass analyzers are highlighted, along with a number of recently reported new GC columns suited for metabolomics. Lastly, multidimensional GC-MS and its application in environmental and biomedical research is presented, along with the importance of bioinformatics.

KEY SCIENTIFIC CONCEPTS OF REVIEW

The purpose of this review is to both highlight and provide an update on GC-MS analytical techniques that are common in metabolomics studies. Specific emphasis is given to the key steps within the GC-MS workflow that those new to this field need to be aware of and the common pitfalls that should be looked out for when starting in this area.

Diagnostic meaning of blood p-cresol concentration in forensic autopsy cases

In some forensic autopsy cases there are high concentrations of p-cresol in the blood. In vivo, p-cresol is the only isomer yielded by intestinal bacteria and is excreted into urine. We investigated the diagnostic meaning of p-cresol in the blood of forensic autopsy cases. Blood samples from 110 autopsy cases within 48 h of the postmortem interval (PMI) and 10 healthy adults were examined. Blood with p-cresol-d₈ as an internal standard was analyzed using a GC-MS/MS method. Using acid and heat deproteinization, free (F) and conjugated (non-protein bound: C; protein bound: PC) p-cresol were individually analyzed. The p-cresol concentrations were 1.39 ± 0.86 µg/ml [mean ± SD] and 1.18 (0.19-18.80) µg/ml [median (range)] in healthy adults and autopsy cases, respectively. The p-cresol showed no significant relationship to age, sex, fasting duration, survival duration, or PMI. No significant differences were found between causes of death. Significantly higher levels of C p-cresol were found in cases with atherosclerosis in the basilar or renal arteries, or stenosis in the coronary artery. Significantly higher levels of p-cresol except F were found in cases with hyalinosis of the kidney. Cases with low BMI also showed significantly higher p-cresol concentrations. The 22 cases of abnormally high total p-cresol were investigated. It was considered that high concentrations of p-cresol could be an indicator of certain diseases and physical conditions that effect the production, absorption, metabolism, circulation, and excretion of p-cresol. Measuring the levels of p-cresol may provide valuable information about the antemortem physical conditions.

Validation of a routine gas chromatography mass spectrometry method for 2-hydroxyglutarate quantification in human serum as a screening tool for detection of idh mutations

High circulating levels of 2-hydroxyglutarate (2HG) have been reported in patients with determinate isocitrate dehydrogenase (IDH) mutated tumors. Recent studies indicate that in malignancies such as acute myeloid leukemia (AML), measurements of 2HG in serum provide useful diagnostic and prognostic information and improve patient selection and monitoring of IDH-targeted treatments. In the current study, we validated a sensitive and specific gas chromatography mass spectrometry (GC-MS) method specifically intended to quantify serum levels of 2HG in routine clinical laboratories. Extraction was liquid-liquid with ethyl acetate, and derivatization was reduced to 3 min of microwave irradiation. The analytical method was linear over a wide dynamic range, presenting acceptable intraday and day-to-day precision and accuracy. The limit of quantification was 10 ng/mL, process efficiency ranged between 38% and 49%, and recovery of added 2HG was 99-105%. 2HG was found to be stable in serum for up to 48 h at both 4 °C and at ambient temperature, and after three freeze-thaw cycles. Microwave derivatizated extracts in the autosampler were found to be stable for up to 120 h. In summary, the present method is useful for quantification of 2HG serum levels in patients with IDH mutated malignancies in clinical laboratories.

Mass-spectrometry-based lipidomics

Lipids, which have a core function in energy storage, signalling and biofilm structures, play important roles in a variety of cellular processes because of the great diversity of their structural and physiochemical properties. Lipidomics is the large-scale profiling and quantification of biogenic lipid molecules, the comprehensive study of their pathways and the interpretation of their physiological significance based on analytical chemistry and statistical analysis. Lipidomics will not only provide insight into the physiological functions of lipid molecules but will also provide an approach to discovering important biomarkers for diagnosis or treatment of human diseases. Mass-spectrometry-based analytical techniques are currently the most widely used and most effective tools for lipid profiling and quantification. In this review, the field of mass-spectrometry-based lipidomics was discussed. Recent progress in all essential steps in lipidomics was carefully discussed in this review, including lipid extraction strategies, separation techniques and mass-spectrometry-based analytical and quantitative methods in lipidomics. We also focused on novel resolution strategies for difficult problems in determining C=C bond positions in lipidomics. Finally, new technologies that were developed in recent years including single-cell lipidomics, flux-based lipidomics and multiomics technologies were also reviewed.

Fully Automated Trimethylsilyl (TMS) Derivatisation Protocol for Metabolite Profiling by GC-MS

Gas Chromatography-Mass Spectrometry (GC-MS) has long been used for metabolite profiling of a wide range of biological samples. Many derivatisation protocols are already available and among these, trimethylsilyl (TMS) derivatisation is one of the most widely used in metabolomics. However, most TMS methods rely on off-line derivatisation prior to GC-MS analysis. In the case of manual off-line TMS derivatisation, the derivative created is unstable, so reduction in recoveries occurs over time. Thus, derivatisation is carried out in small batches. Here, we present a fully automated TMS derivatisation protocol using robotic autosamplers and we also evaluate a commercial software, Maestro available from Gerstel GmbH. Because of automation, there was no waiting time of derivatised samples on the autosamplers, thus reducing degradation of unstable metabolites. Moreover, this method allowed us to overlap samples and improved throughputs. We compared data obtained from both manual and automated TMS methods performed on three different matrices, including standard mix, wine, and plasma samples. The automated TMS method showed better reproducibility and higher peak intensity for most of the identified metabolites than the manual derivatisation method. We also validated the automated method using 114 quality control plasma samples. Additionally, we showed that this online method was highly reproducible for most of the metabolites detected and identified (RSD < 20) and specifically achieved excellent results for sugars, sugar alcohols, and some organic acids. To the very best of our knowledge, this is the first time that the automated TMS method has been applied to analyse a large number of complex plasma samples. Furthermore, we found that this method was highly applicable for routine metabolite profiling (both targeted and untargeted) in any metabolomics laboratory.

Improved conventional and microwave-assisted silylation protocols for simultaneous gas chromatographic determination of tocopherols and sterols: Method development and multi-response optimization

This paper reports on improved conventional thermal silylation (CTS) and microwave-assisted silylation (MAS) methods for simultaneous determination of tocopherols and sterols by gas chromatography. Reaction parameters in each of the methods developed were systematically optimized using a full factorial design followed by a central composite design. Initially, experimental conditions for CTS were optimized using a block heater. Further, a rapid MAS was developed and optimized. To understand microwave heating mechanisms, MAS was optimized by two distinct modes of microwave heating: temperature-controlled MAS and power-controlled MAS, using dedicated instruments where reaction temperature and microwave power level were controlled and monitored online. Developed methods: were compared with routine overnight derivatization. On a comprehensive level, while both CTS and MAS were found to be efficient derivatization techniques, MAS significantly reduced the reaction time. The optimal derivatization temperature and time for CTS found to be 55°C and 54min, while it was 87°C and 1.2min for temperature-controlled MAS. Further, a microwave power of 300W and a derivatization time 0.5min found to be optimal for power-controlled MAS. The use of an appropriate derivatization solvent, such as pyridine, was found to be critical for the successful determination. Catalysts, like potassium acetate and 4-dimethylaminopyridine, enhanced the efficiency slightly. The developed methods showed excellent analytical performance in terms of linearity, accuracy and precision.

Determination of "new psychoactive substances" in postmortem matrices using microwave derivatization and gas chromatography-mass spectrometry

Despite worldwide efforts aiming to ban the marketing and subsequent abuse of psychoactive substances such as synthetic cathinones and phenethylamines, there has been an alarming growth of both in recent years. Different compounds similar to those already existing are continuously appearing in the market in order to circumvent the legislation. An analytical methodology has been validated for qualitative and quantitative determinations of D-cathine (D-norpseudoehedrine), ephedrine, methcathinone, 1-(4-methoxyphenyl)-propan-2-amine (PMA), mephedrone, methedrone, 2,5-dimethoxy-4-methylamphetamine (DOM), 4-bromo-2,5-dimethoxyamphetamine (DOB), 2,5-dimethoxyphenethylamine (2C-H), 4-bromo-2,5-dimethoxyphenethylamine (2C-B), 4-iodo-2,5-dimethoxyphenethylamine (2C-I), 2-[2,5-dimethoxy-4-(ethylthio)phenyl]ethanamine (2C-T-2), 2,5-dimethoxy-4-isopropylthiophenethylamine (2C-T-4) and 2-[2,5-dimethoxy-4-(propylthio)phenyl]ethanamine (2C-T-7), in low volumes of vitreous humor (100 μL), pericardial fluid (250 μL) and whole blood (250 μL), using deutered amphetamine, ephedrine and mephedrone as internal standards. The validation parameters included selectivity, linearity and limits of detection and quantification, intra- and interday precision and trueness, recovery and stability. The method included mixed-mode solid phase extraction, followed by microwave fast derivatization and analysis by gas chromatography-mass spectrometry operated in selected ion monitoring mode. The procedure was linear between 5 and 600 ng/mL, with determination coefficients higher than 0.99 for all analytes. Intra- and interday precision ranged from 0.1 to 13.6%, while accuracy variability was within 80-120% interval from the nominal concentration at all studied levels. The extraction efficiencies ranged from 76.6 to 112.8%. Stability was considered acceptable for all compounds in the studied matrices. The developed assay was applied to authentic samples of the Laboratory of Chemistry and Forensic Toxicology, Centre Branch, of the National Institute of Legal Medicine and Forensic Sciences, Portugal.

Derivatization of steroids in biological samples for GC–MS and LC–MS analyses

The determination of steroids in biological samples is essential in different areas of knowledge. MS combined with either GC or LC is considered the best analytical technique for specific and sensitive determinations. However, due to the physicochemical properties of some steroids, and the low concentrations found in biological samples, the formation of a derivative prior to their analysis is required. In GC–MS determinations, derivatization is needed for generating volatile and thermally stable compounds. The improvement in terms of stability and chromatographic retention are the main reasons for selecting the derivatization agent. On the other hand, derivatization is not compulsory in LC–MS analyses and the derivatization is typically used for improving the ionization and therefore the overall sensitivity achieved.

Current status and recent advantages in derivatization procedures in human doping control

Derivatization is one of the most important steps during sample preparation in doping control analysis. Its main purpose is the enhancement of chromatographic separation and mass spectrometric detection of analytes in the full range of laboratory doping control activities. Its application is shown to broaden the detectable range of compounds, even in LC–MS analysis, where derivatization is not a prerequisite. The impact of derivatization initiates from the stage of the metabolic studies of doping agents up to the discovery of doping markers, by inclusion of the screening and confirmation procedures of prohibited substances in athlete's urine samples. Derivatization renders an unlimited number of opportunities to advanced analyte detection.

Determination of homologous distributions of bisEMA dimethacrylates in bulk-fill resin-composites by GC-MS

OBJECTIVES

Ethoxylated bisphenol A dimethacrylate (bisEMA) is a basis monomer in several dental resin composites. It was the aim of the present study to develop a method allowing detection of bisEMA and its different degrees of ethoxylation eluted from polymerized resin composites.

METHODS

High-temperature gas chromatography/mass spectrometry (HT-GC/MS) by direct on-column injection was used to identify ethoxylated bisEMA in ethanol/water (3:1) eluates from polymerized specimen of four bulk-fill resin composites - Venus(®) bulk fill, Surefil(®) SDR™ flow, Filtek™ Bulk Fill and Sonic Fill™. Additionally, the unpolymerised pastes were analysed.

RESULTS

The developed method allowed identification of a homologous series of bisEMA up to twelve ethoxy groups in the unpolymerised materials. The molecular masses of the homologous bisEMA varied between 452 g/mol and 892 g/mol and were detected for retention times from 9.43 min to 13.36 min. Analysis of eluates from polymerised materials identified bisEMA monomers with less than 6 ethoxy groups. Chromatograms showed larger peak areas for the lower volatile bisEMA with 4-6 ethoxy groups compared with higher volatile bisEMA with 2 or 3 ethoxy groups, thus indicating that the amounts of these homologues in the pastes were higher.

SIGNIFICANCE

Ethoxylated bisEMA with up to twelve ethoxy groups can be identified by HT-GC/MS. In all eluates bisEMA was found. The higher the number of ethoxy groups the lower are the peak areas from bisEMA in the gas chromatogram. These findings may be significant for toxicological analysis of resin-composites incorporating bis-EMA.

Microwave-assisted derivatization: application to steroid profiling by gas chromatography/mass spectrometry

Gas chromatography-mass spectrometry (GC-MS) remains as the gold-standard technique for the study of the steroid metabolome. A main limitation is the need of performing a derivatization step since incubation with strong silylations agents for long periods of time (usually 16 h) is required for the derivatization of hindered hydroxyls present in some steroids of interest. In the present work, a rapid, simple and reproducible microwave-assisted derivatization method was developed. In the method, 36 steroids already treated with methoxyamine (2% in pyridine) were silylated with 50 μl of N-trimethylsilylimidazole by using microwave irradiation, and the formed methyloxime-trimethylsilyl derivatives were analyzed by GC-MS. Microwave power and derivatization time silylation conditions were optimized being the optimum conditions 600 W and 3 min respectively. In order to evaluate the usefulness of this technique, the urine steroid profiles for 20 healthy individuals were analyzed. The results of a comparison of microwave irradiation with the classical heating protocol showed similar derivatization yields, thus suggesting that microwave-assisted silylation is a valid tool for the rapid steroid metabolome study.

Rapid quantification of yeast lipid using microwave-assisted total lipid extraction and HPLC-CAD

We here present simple and rapid methods for fast screening of yeast lipids in Saccharomyces cerevisiae. First we introduced a microwave-assisted technique for fast lipid extraction that allows the extraction of lipids within 10 min. The new method enhances extraction rate by 27 times, while maintaining product yields comparable to conventional methods (n = 14, P > 0.05). The recovery (n = 3) from spiking of synthetic standards were 92 ± 6% for cholesterol, 95 ± 4% for triacylglycerol, and 92 ± 4% for free fatty acids. Additionally, the new extraction method combines cell disruption and extraction in one step, and the approach, therefore, not only greatly simplifies sample handling but also reduces analysis time and minimizes sample loss during sample preparation. Second, we developed a chromatographic separation that allowed separation of neutral and polar lipids from the extracted samples within a single run. The separation was performed based on a three gradient solvent system combined with hydrophilic interaction liquid chromatography-HPLC followed by detection using a charged aerosol detector. The method was shown to be highly reproducible in terms of retention time of the analytes (intraday; 0.002-0.034% RSD; n = 10, interday; 0.04-1.35% RSD; n = 5) and peak area (intraday; 0.63-6% RSD; n = 10, interday; 4-12% RSD; n = 5).

Alkylsilyl derivatives for gas chromatography

Alkylsilyl reagents are the most widely used reagents for the derivatization of polar compounds containing labile hydrogen atoms for gas chromatography. In this article the reagents and reaction conditions for the formation of trimethylsilyl, alkyldimethylsilyl (particularly t-butyldimethylsilyl), cyclic siliconides, haloalkyldimethylsilyl, and flophemesyl (pentafluorophenyldimethylsilyl) derivatives for a wide range of functional groups are reviewed. The importance of steric hindrance on reaction rates and completion, choice of reaction conditions, stability of derivatives, and options for selective detection are described.

Simultaneous analysis of non-steroidal anti-inflammatory drugs and estrogenic hormones in water and wastewater samples using gas chromatography-mass spectrometry and gas chromatography with electron capture detection

Non-steroidal anti-inflammatory drugs are the group of pharmaceuticals that is most often found in the environment, whereas estrogenic hormones are considered to be potent endocrine disruptors. However, the fate and persistence of these compounds in the environment are still unclear. In this study we propose two approaches for determining these compounds in environmental water samples: GC-MS using time windows and operating in selected ion-monitoring mode (SIM) and, for the first time, gas chromatography with electron capture detection (GC-ECD). The identification criteria of both methods fulfilled the requirements of Directive 2002/657/EC. The use of time windows improved the sensitivity of GC-MS measurements. In GC-MS analysis the pharmaceuticals were determined as trimethylsilyl, in GC-ECD as pentafluoropropionyl derivatives. The influence of such parameters as the type of reagent, type of solvent, reaction time, reaction temperature and microwave irradiation in a household microwave oven on the efficacy of silylation was investigated. Derivatization using N,O-bis(trimethylsilyl)trifluoroacetamide (BSTFA) and 1% trimethylchlorosilane (TMCS) in pyridine (1:1, v/v) for 30 min in 60 °C was found to be optimal. Optimization of the solid phase extraction procedure (SPE) confirmed that the application of Oasis HLB cartridges, the acidification of loading samples to pH2 and the use of methanol as eluent gave the best absolute recoveries (ARs) of the target compounds. The following ARs of all the compounds were achieved: 58.2-106.8% in influent wastewater, 77.8-103.4% in effluent wastewater and 81.2-101.9% in surface water samples. Validation of the SPE-GC-MS method enables 13 pharmaceuticals to be determined with MDLs between 3.3 and 343.6 ng/L, depending on the analytes and matrices. GC-ECD analysis enables the determination of 6 pharmaceuticals in surface water samples with MDLs between 0.7 and 5.4 ng/L. The proposed methods were successfully used for analyzing selected pharmaceuticals in wastewaters and river waters in Poland.

Metabolic profiling of Lactococcus lactis under different culture conditions

Gas chromatography mass spectrometry (GC-MS) and headspace gas chromatography mass spectrometry (HS/GC-MS) were used to study metabolites produced by Lactococcus lactis subsp. cremoris MG1363 grown at a temperature of 30 °C with and without agitation at 150 rpm, and at 37 °C without agitation. It was observed that L. lactis produced more organic acids under agitation. Primary alcohols, aldehydes, ketones and polyols were identified as the corresponding trimethylsilyl (TMS) derivatives, whereas amino acids and organic acids, including fatty acids, were detected through methyl chloroformate derivatization. HS analysis indicated that branched-chain methyl aldehydes, including 2-methylbutanal, 3-methylbutanal, and 2-methylpropanal are degdradation products of isoleucine, leucine or valine. Multivariate analysis (MVA) using partial least squares discriminant analysis (PLS-DA) revealed the major differences between treatments were due to changes of amino acids and fermentation products.

Fast and accurate preparation fatty acid methyl esters by microwave-assisted derivatization in the yeast Saccharomyces cerevisiae

We present a fast and accurate method for preparation of fatty acid methyl esters (FAMEs) using microwave-assisted derivatization of fatty acids present in yeast samples. The esterification of free/bound fatty acids to FAMEs was completed within 5 min, which is 24 times faster than with conventional heating methods. The developed method was validated in two ways: (1) through comparison with a conventional method (hot plate) and (2) through validation with the standard reference material (SRM) 3275-2 omega-3 and omega-6 fatty acids in fish oil (from the Nation Institute of Standards and Technology, USA). There were no significant differences (P>0.05) in yields of FAMEs with both validations. By performing a simple modification of closed-vessel microwave heating, it was possible to carry out the esterification in Pyrex glass tubes kept inside the closed vessel. Hereby, we are able to increase the number of sample preparations to several hundred samples per day as the time for preparation of reused vessels was eliminated. Pretreated cell disruption steps are not required, since the direct FAME preparation provides equally quantitative results. The new microwave-assisted derivatization method facilitates the preparation of FAMEs directly from yeast cells, but the method is likely to also be applicable for other biological samples.

Microwave-assisted synthesis of colloidal inorganic nanocrystals

Colloidal inorganic nanocrystals stand out as an important class of advanced nanomaterials owing to the flexibility with which their physical-chemical properties can be controlled through size, shape, and compositional engineering in the synthesis stage and the versatility with which they can be implemented into technological applications in fields as diverse as optoelectronics, energy conversion/production, catalysis, and biomedicine. The use of microwave irradiation as a non-classical energy source has become increasingly popular in the preparation of nanocrystals (which generally involves complex and time-consuming processing of molecular precursors in the presence of solvents, ligands and/or surfactants at elevated temperatures). Similar to its now widespread use in organic chemistry, the efficiency of "microwave flash heating" in dramatically reducing overall processing times is one of the main advantages associated with this technique. This Review illustrates microwave-assisted methods that have been developed to synthesize colloidal inorganic nanocrystals and critically evaluates the specific roles that microwave irradiation may play in the formation of these nanomaterials.

An examination of pentafluorobenzoyl derivatization strategies for the analysis of fatty alcohols using gas chromatography/electron capture negative ion chemical ionization-mass spectrometry

Gas chromatography/electron capture negative ion chemical ionization-mass spectrometry (GC/ECNICI-MS) combined with pentafluorobenzoyl derivatization (PFBoyl) is frequently used for the sensitive detection of fatty alcohols (FOH). However, this derivatization technique suffers from a lack of established reaction protocols, time-consuming reactions, and the presence of reagent artifacts or unwanted derivatization by-products which can hinder analyte detection. Here, strategies are presented to reduce the problems associated with PFBoyl-derivatization, including (1) the optimization of reaction conditions (derivatization time and temperature) for a variety of PFBoyl-derivatized FOH, (2) an investigation of microwave-accelerated derivatization (MAD) as a rapid alternative heating mechanism for the PFBoyl-derivatization of FOH, and (3) an analysis of an alternative strategy employing a solvent extraction procedure post-derivatization to reduce the detrimental effects commonly associated with PFBoyl derivatization reagents. The optimal reaction conditions for the PFBoyl-derivatization of FOH were determined to be 60°C for 45 min. The investigation in MAD demonstrated the potential of obtaining comparable PFBoyl-derivatizations to those obtained using traditional heating methods, albeit in a reaction time of 3 min. An examination of several solvents for post-derivatization extraction revealed improved relative response factors in comparison to those obtained without solvent extraction. The best solvents for the PFBoyl-FOH extraction, dichloromethane and tert-butyl methyl ether, were also compared to the no solvent extraction samples with standard response curves and PFBoyl-derivatized FOH in Bligh-Dyer extracted rat plasma.