Removal of Disperse Red dye by bamboo-based activated carbon: optimisation, kinetics and equilibrium

Preparation and characterization of graphene oxide/O-carboxymethyl chitosan (GO/CMC) composite and its unsymmetrical dimethylhydrazine (UDMH) adsorption performance from wastewater

The removal of unsymmetrical dimethylhydrazine (UDMH) has long been a concern because of its harmful effect on the environment and humans. This study aimed to prepare a novel graphene oxide/O-carboxymethyl chitosan (GO/CMC) composite adsorbent using the solution-blending method for the removal of UDMH from wastewater. The prepared GO/CMC was systematically characterized by Fourier-transform infrared, Raman, scanning electronic microscopy, transmission electron microscopy, thermogravimetric, and zeta potential analyses. The effects of initial pH, temperature, adsorbent dosage, initial concentration, contact time, and recyclability on the UDMH adsorption behaviour of GO/CMC were studied. The adsorption kinetics was consistent with the pseudo-second-order kinetics model, and the adsorption process was mainly controlled by chemisorption. Adsorption isotherms indicated that the adsorption of UDMH by GO/CMC followed the Langmuir adsorption isotherm. The adsorption mechanisms were mainly electrostatic attraction, hydrogen bonding, and surface complexation. Furthermore, GO/CMC composites can be used as a renewable and eco-friendly adsorbent for the removal of UDMH wastewater. The designed GO/CMC composites exhibited a relatively satisfactory recyclability and removal efficiency after five adsorption-desorption cycles.

Adsorption capacity of activated carbon derived from date seeds: Characterization, optimization, kinetic and equilibrium studies

Agricultural wastes have the potential to be reused in applications such as water/wastewater treatment. Several studies have focused on activating organic waste, such as date seeds, to produce activated carbon. However, these studies have always assumed that all date seeds behave similarly to each other. In this study, we evaluated different types of date seeds and characterized their physical-chemical properties. The results showed variation in the seed-to-fruit weight percentage, ash content, and moisture content among different seed types. Different activation procedures were performed to find the optimum combination of physical and chemical interventions. KOH impregnation yielded better results than H₃PO₄ impregnation. The maximum adsorption capacity was measured for nine different types of date seeds, and the Khalas seed type yielded the highest methylene blue (MB) adsorption capacity of 165 mg of MB/g of activated date seeds (ADS), which is 71% of the capacity of commercial activated carbon (CAC). Kinetics model was fitted to the experimental data, and the pseudo-second-order model provided the best fit, indicating that the adsorption process occurred following a chemical process rather than being controlled by intraparticle diffusion only. The results showed no significant difference among the three isotherm models used to fit the experimental data. The results indicated that there is a significant difference among various types of seeds regarding adsorption performance. The application of ADS in treating synthetic produced water showed that its performance is one third that of CAC. ADS showed promising potential in comparison with CAC, mostly considering the costs involved with CAC.

High thiabendazole fungicide uptake using Cellana tramoserica shells modified by copper: characterization, adsorption mechanism, and optimization using CCD-RSM approach

In this paper, Cellana tramoserica (CT) shells were modified by copper and used as an adsorbent to remove thiabendazole (TBZ) from aqueous media. The removal efficiency of TBZ onto CT shells and modified Cellana tramoserica (CT-Cu) shells was investigated by considering the following parameters: initial pesticide concentration, solution pH, agitation time, temperature, and adsorbent mass. The experimental results show that the pseudo-first-order and Langmuir models well describe the adsorption process. The maximum adsorption amount for CT and CT-Cu is 319.68 mg/g and 376.12 mg/g, respectively. CT-Cu showed higher TBZ removal efficiency than CT, explained by the ligand exchange between the water and the pesticide molecules in the metal coordination sphere. Response surface methodology combined with central composite design (RSM-CCD) was used to optimize the adsorption conditions. Optimized values were obtained at 5 for pH, 50 ppm, 120 min, and 20 mg of CT-Cu adsorbent. Under these optimal conditions, 91% of TBZ was removed by adsorption onto CT-Cu. Graphical abstract.

A Comprehensive Review of Effective Adsorbents Used for the Removal of Dyes from Wastewater

Aim:

The objective of the review paper aims to explore and to provide the insight of various low-cost adsorbents prepared and used in the removal of hazardous dye pollutants from the contaminated industrial effluents.

Background:

The major untreated discharge from the textile industries constitutes a wide range of organic contaminants with the enhanced concentration of biological oxygen demand and chemical oxygen demand inthe water bodies. Dyes are considered as the major water contaminants and this quest the researchers to adopt various technologies to remove the hazardous dye pollutants from the aquatic environment. Dyes are the chemical compounds that tend to adhere themselves with metal or salts by covalent bond formation or complexes by mechanical retention or physical adsorption so as to impart colours to which it is being applied.

Objective:

Numerous treatment methodologies which have been applied to the degradation of dyes. The current study has been focused on the distinct low cost and cost-effective adsorbents used in the removal of various dye pollutants. Also, the application of nanoparticles in the removal of the hazardous dye pollutants had received great interest because of its size and high reactive nature.

Methods:

The treatment technologies used in the removal of dye pollutants from wastewater have been listed as adsorption, coagulation, electrocoagulation, flocculation, membrane filtration, oxidation and biological treatment.

Results:

The complex structure of the dyes causes a great harmful impact on the aquatic environment. Though numerous treatment technologies have been applied, adsorption has been preferred by various researchers because of its cost-effective nature.

Conclusion:

The various adsorbents are used in the removal of cationic, anionic and non-ionic dyes. The different types of adsorbent from agricultural waste, activated carbons, nanomaterials and biomaterials have been discussed with the advantages and limitations.

Removal of Disperse Orange and Disperse Blue dyes present in textile mill effluent using zeolite synthesized from cenospheres

In this research, an efficient, ecofriendly method of using coal fly ash in the form of zeolite to treat wastewater containing dyes was studied. Response surface methodology involving Box-Behnken design was applied to a batch process to evaluate the effect of process parameters such as contact time, dye concentration, agitation speed, pH, and adsorbent dosage onto zeolite. Disperse Orange 25 (DO) dye showed a maximum of 96% removal under optimal conditions of contact time of 119 min, dye concentration of 38.00 mg/L, agitation speed of 158 rpm, pH of 6.10, and adsorbent dosage of 0.67 g/L, whereas 95.23% of Disperse Blue 79:1 (DB) dye removal was observed at adsorbent dose of 1.05 g/L, dye concentration of 26.72 mg/L, agitation speed of 145 rpm, pH of 5.68, and contact time of 122 min. It was concluded that cenosphere-derivatized zeolite adsorbent is efficient, ecofriendly, and economical and has high potential for the removal of DO and DB dyes from aqueous solutions.

Basic red 2 and methyl violet adsorption by date pits: adsorbent characterization, optimization by RSM and CCD, equilibrium and kinetic studies

The potential of raw date pits as a natural, widely available and low-cost agricultural waste has been studied in order to adsorb cationic dyes from an aqueous solution. Date pits were characterized by FTIR, SEM, BET, and XRD analysis. To optimize removal of two industrial dyes, basic red 2 (BR2) and methyl violet (MV), from aqueous solution using date pits, response surface methodology (RSM) is employed. Tests were carried out as per central composite design (CCD) with four input parameters namely contact time, temperature, initial concentration of adsorbate, and pH. Second-order polynomial model better fits experimental data for BR2 and MV and optimum values were then determined. In the optimum conditions, kinetic study was conducted and the pseudo-second-order model was found the best fitted model compared to pseudo-first-order model. Moreover, it was shown that intraparticle diffusion was not the sole controlling step and could be associated with other transfer resistance. On other hand, equilibrium isotherms were obtained for BR2 and MV and their maximum adsorption capacities were 92 and 136 mg g^-1 respectively. Two-parameter isotherm models like Langmuir, Temkin, Freundlich, Dubinin-Radushkevich, and Halsay were investigated to fit equilibrium data. Three error functions of residual root mean square error, chi-square statistic, and average relative error were used to comfort us in the selected models, which were actually Dubinin-Radushkevich and Langmuir for BR2 and Frendlich, Temkin, and Halsay for MV.

Fabrication of phosphonium bamboo cellulose by triphenylphosphine: preparation, characterization, and adsorption of Acid Black 24

Cellulose from bamboo shavings (BC) separated and modified by grafting triphenylphosphine, which was used as an adsorbent for the removal of Acid Black 24 from aqueous solution. The quaternary phosphonium-based bamboo cellulose (PBC) was characterized by FTIR and SEM measurements. The FTIR studies showed that the quaternary phosphonium group was successfully grafted onto the BC molecular structure. The effects of PBC dosage, contact time, initial dye concentration, temperature, and pH on the adsorption performance were studied. The nonlinear fitting kinetics and isotherms models were also conducted. The pseudo-second-order, intra-particle diffusion and Langmuir models were more suitable for analyzing the adsorption behavior of PBC for Acid Black 24 dye. The adsorption activation energy was lower than 40 kJ mol^-1, and the ΔH⁰ value was in the range of 20~80 kJ mol^-1, indicating that PBC played a dominant role in the physical purification of dye. The results of thermodynamic analysis indicated that the adsorption was a spontaneous endothermic purification process. Adsorbents had a good reusability and high adsorption performance for dye removal. The adsorbents PBC had a good reusability and could effectively remove residual Acid Black 24 dye with good development prospects in the field of biomass adsorbent materials.

Modeling and optimization of lime-based stabilization in high alkaline arsenic-bearing sludges with a central composite design

This study focuses on the modeling and optimization of lime-based stabilization in high alkaline arsenic-bearing sludges (HAABS) and describes the relationship between the arsenic leachate concentration (ALC) and stabilization parameters to develop a prediction model for obtaining the optimal process parameters and conditions. A central composite design (CCD) along with response surface methodology (RSM) was conducted to model and investigate the stabilization process with three independent variables: the Ca/As mole ratio, reaction time and liquid/solid ratio, along with their interactions. The obvious characteristic changes of the HAABS before and after stabilization were verified by X-ray diffraction (XRD), scanning electron microscopy (SEM), particle size distribution (PSD) and the community bureau of reference (BCR) sequential extraction procedure. A prediction model Y_(ALC) with a statistically significant P-value <0.01 and high correlation coefficient R² = 93.22% was obtained. The optimal parameters were successfully predicted by the model for the minimum ALC of 0.312 mg/L, which was validated with the experimental result (0.306 mg/L). The XRD, SEM and PSD results indicated that crystal calcium arsenate Ca₅(AsO₄)₃OH and Ca₄(OH)₂(AsO₄)₂·4H₂O formation played an important role in minimizing the ALC. The BCR sequential extraction results demonstrated that the treated HAABS were stable in a weak acidic environment for a short time but posed a potential environmental risk after a long time. The results clearly confirm that the proposed three-factor CCD is an effective approach for modeling the stabilization of HAABS. However, further solidification technology is suggested for use after lime-based stabilization treatment of arsenic-bearing sludges.

Carbon-Based Functional Materials Derived from Waste for Water Remediation and Energy Storage

Carbon-based functional materials hold the key for solving global challenges in the areas of water scarcity and the energy crisis. Although carbon nanotubes (CNTs) and graphene have shown promising results in various fields of application, their high preparation cost and low production yield still dramatically hinder their wide practical applications. Therefore, there is an urgent call for preparing carbon-based functional materials from low-cost, abundant, and sustainable sources. Recent innovative strategies have been developed to convert various waste materials into valuable carbon-based functional materials. These waste-derived carbon-based functional materials have shown great potential in many applications, especially as sorbents for water remediation and electrodes for energy storage. Here, the research progress in the preparation of waste-derived carbon-based functional materials is summarized, along with their applications in water remediation and energy storage; challenges and future research directions in this emerging research field are also discussed.

Optimization of a cationic dye removal by a chemically modified agriculture by-product using response surface methodology: biomasses characterization and adsorption properties

The present study investigates the alkaline modification of raw orange tree sawdust (ROS) for an optimal removal of methylene blue (MB), as a cationic dye model, from synthetic solutions. The effects of operating parameters, namely, sodium hydroxide (NaOH) concentrations, ROS doses in NaOH solutions, stirring times, and initial MB concentrations on dye removal efficiency, were followed in batch mode. The process optimization was performed through the response surface methodology approach (RSM) by using Minitab17 software. The results showed that the order of importance of the followed parameters was NaOH treatment concentrations > stirring times > initial MB concentrations > ROS doses in NaOH solutions. The optimal experimental conditions ensuring the maximal MB removal efficiency was found for a NaOH treatment concentration of 0.14 M, a stirring time of 1 h, a ROS dose in NaOH solutions of 50 g L^-1, and an initial MB concentration of 69.5 mg L^-1. Specific analyses of the raw and alkali-treated biomasses, e.g., SEM/EDS and XRD analyses, demonstrated an important modification of the crystalline structure of the wooden material and a significant increase in its surface basic functional groups. Kinetic and isotherm studies of MB removal from synthetic solutions by ROS and the alkali-treated material (ATOS) showed that for both adsorbents, the pseudo-second-order and Langmuir model fitted the best the experimental data, respectively, which indicates that MB removal might be mainly a chemical and a monolayer process. Furthermore, thanks to the chemical modification of the ROS, the MB maximal uptake capacity has increased from about 39.7 to 78.7 mg g^-1. On the other hand, due to the competition phenomenon, the coexistence of MB and Zn(II) ions could significantly decrease the MB removal efficiency. A maximal decrease of about 32 % was registered for an initial Zn(II) concentration of 140 mg L^-1. Desorption experiments undertaken at natural pH (without adjustment: pH = 6) and with different NaCl concentrations emphasized that the adsorbed MB could be significantly desorbed from both the tested materials, offering their possible reuse as efficient adsorbents. All these results confirmed that NaOH-treated orange tree sawdust could be considered as an efficient, economic, and ecological alternative for the removal of cationic dyes from industrial wastewaters.

Preparation, Surface and Pore Structure of High Surface Area Activated Carbon Fibers from Bamboo by Steam Activation

High surface area activated carbon fibers (ACF) have been prepared from bamboo by steam activation after liquefaction and curing. The influences of activation temperature on the microstructure, surface area and porosity were investigated. The results showed that ACF from bamboo at 850 °C have the maximum iodine and methylene blue adsorption values. Aside from the graphitic carbon, phenolic and carbonyl groups were the predominant functions on the surface of activated carbon fiber from bamboo. The prepared ACF from bamboo were found to be mainly type I of isotherm, but the mesoporosity presented an increasing trend after 700 °C. The surface area and micropore volume of samples, which were determined by application of the Brunauer-Emmett-Teller (BET) and t-plot methods, were as high as 2024 m²/g and 0.569 cm³/g, respectively. It was also found that the higher activation temperature produced the more ordered microcrystalline structure of ACF from bamboo.