Adsorption performance and mechanism of magnetic reduced graphene oxide in glyphosate contaminated water

Electrochemical Detection of Glyphosate in Surface Water Samples Based on Modified Screen-Printed Electrodes

This study addresses the necessity to monitor the presence of glyphosate (Gly) in waters, highlighting the need for on-site detection of Gly by using electrochemical sensors in environmental and agricultural monitoring programs. Two approaches were employed: (1) modification with graphene decorated with gold nanoparticles (AuNPs-Gr) and dispersed in either dimethylformamide (DMF) or a solution containing Nafion and isopropanol (NAF), and (2) molecularly imprinted polymers (MIPs) based on polypyrrole (PPy) deposited on gold SPEs (AuSPE). Electrochemical characterization revealed that sensors made of AuNPs-Gr/SPCE exhibited enhanced conductivity, larger active area, and improved charge transfer kinetics compared to unmodified SPEs and SPEs modified with graphene alone. However, the indirect detection mechanism of Gly via complex formation with metallic cations in AuNPs-Gr-based sensors introduces complexities and compromises sensitivity and selectivity. In contrast, MIPPy/AuSPE sensors demonstrated superior performance, offering enhanced reliability and sensitivity for Gly analysis. The MIPPy/AuSPE sensor allowed the detection of Gly concentrations as low as 5 ng/L, with excellent selectivity and reproducibility. Moreover, testing in real surface water samples from the Olt River in Romania showed recovery rates ranging from 90% to 99%, highlighting the effectiveness of the detection method. Future perspectives include expanding the investigation to monitor Gly decomposition in aquatic environments over time, providing insights into the decomposition's long-term effects on water quality and ecosystem health, and modifying regulatory measures and agricultural practices for mitigating its impact. This research contributes to the development of robust and reliable electrochemical sensors for on-site monitoring of Glyphosate in environmental and agricultural settings.

Isolation of aqueous pesticides on surface-functionalized SBA-15: glyphosate kinetics and detailed empirical insights for atrazine

Atrazine and glyphosate are two of the most used pesticides around the world causing serious water contamination. In this study, amine-functionalized Santa Barbara Amorphous-15 silica (SBA-15-NH2) was synthesized and employed for the aqueous adsorption of atrazine and glyphosate. The adsorbent was mesoporous post-functionalization with lower surface area, pore volume, size, and stability when compared to the SBA-15. The pesticides adsorption rates were high with over 85% of potential adsorption having occurred within the initial 180 min. The equilibria for atrazine and glyphosate adsorption were 60 and 360 min, respectively, and the rate data fit the fractal pseudo-second-order and pseudo-second-order models, respectively. Atrazine adsorption was higher at lower solution pH with reduced adsorption as the pH value increased. There was enhanced atrazine adsorption as temperature increased from 22 to 32 °C, but further temperature rise resulted in lower adsorption compared to that recorded at 22 °C. The processes comprise electrostatic interaction, trapping of atrazine within mesopores, and multi-layer adsorption of atrazine on surface-adsorbed atrazine. The equilibrium data fitted the Langmuir adsorption isotherm model better than the Freundlich. The SBA-15-NH2 adsorption capacity for atrazine and glyphosate was better than many adsorbents reported in literature, the adsorbent is reusable, and exhibited sustained efficiencies for atrazine that was ≥82% even after 3-cycles, an indication of chemical stability and renewability.

Elucidation of the role of metals in the adsorption and photodegradation of herbicides by metal-organic frameworks

Here, four MOFs, namely Sc-TBAPy, Al-TBAPy, Y-TBAPy, and Fe-TBAPy (TBAPy: 1,3,6,8-tetrakis(p-benzoic acid)pyrene), were characterized and evaluated for their ability to remediate glyphosate (GP) from water. Among these materials, Sc-TBAPy demonstrates superior performance in both the adsorption and degradation of GP. Upon light irradiation for 5 min, Sc-TBAPy completely degrades 100% of GP in a 1.5 mM aqueous solution. Femtosecond transient absorption spectroscopy reveals that Sc-TBAPy exhibits enhanced charge transfer character compared to the other MOFs, as well as suppressed formation of emissive excimers that could impede photocatalysis. This finding was further supported by hydrogen evolution half-reaction (HER) experiments, which demonstrated Sc-TBAPy's superior catalytic activity for water splitting. In addition to its faster adsorption and more efficient photodegradation of GP, Sc-TBAPy also followed a selective pathway towards the oxidation of GP, avoiding the formation of toxic aminomethylphosphonic acid observed with the other M3+-TBAPy MOFs. To investigate the selectivity observed with Sc-TBAPy, electron spin resonance, depleted oxygen conditions, and solvent exchange with D2O were employed to elucidate the role of different reactive oxygen species on GP photodegradation. The findings indicate that singlet oxygen (1O2) plays a critical role in the selective photodegradation pathway achieved by Sc-TBAPy.

Removal of glyphosate (GLY) and aminomethylphosphonic acid (AMPA) by ultrafiltration with permeate-side polymer-based spherical activated carbon (UF-PBSAC)

Glyphosate (GLY) is the most commonly used herbicide worldwide, and aminomethylphosphonic acid (AMPA) is one of its main metabolites. GLY and AMPA are toxic to humans, and their complex physicochemical properties present challenges in their removal from water. Several technologies have been applied to remove GLY and AMPA such as adsorption, filtration, and degradation with varied efficiencies. In previous works, an ultrafiltration membrane with permeate-side polymer-based spherical activated carbon (UF-PBSAC) showed the feasibility of removing uncharged micropollutants via adsorption in a flow-through configuration. The same UF-PBSAC was investigated for GLY and AMPA adsorption to assess the removal of charged and lower molecular weight micropollutants. The results indicated that both surface area and hydraulic residence time were limiting factors in GLY/AMPA adsorption by UF-PBSAC. The higher external surface of PBSAC with strong affinity for GLY and AMPA showed higher removal in a dynamic process where the hydraulic residence time was short (tens of seconds). Extending hydraulic residence times (hundreds of seconds) resulted in higher GLY/AMPA removal by allowing GLY/AMPA to diffuse into the PBSAC pores and reach more surfaces. Enhancement was achieved by minimising both limiting factors (external surface and hydraulic residence time) with a low flux of 25 L/m2.h, increased PBSAC layer of 6 mm, and small PBSAC particle size of 78 µm. With this configuration, UF-PBSAC could remove 98 % of GLY and 95 % of AMPA from an initial concentration of 1000 ng/L at pH 8.2 ± 0.2 and meet European Union (EU) regulation for herbicides (100 ng/L for individuals and 500 ng/L for total herbicides). The results implied that UF-PBSAC was able to remove charged micropollutants to the required levels and had potential for application in wastewater treatment and water reuse.

Influence of Inorganic Anions on the Chemical Stability of Molybdenum Disulfide Nanosheets in the Aqueous Environment

Chemical stability is closely associated with the transformations and bioavailabilities of engineered nanomaterials and is a key factor that governs broader and long-term application. With the growing utilization of molybdenum disulfide (MoS2) nanosheets in water treatment and purification processes, it is crucial to evaluate the stability of MoS2 nanosheets in aquatic environments. Nonetheless, the effects of anionic species on MoS2 remain largely unexplored. Herein, the stability of chemically exfoliated MoS2 nanosheets (ceMoS2) was assessed in the presence of inorganic anions. The results showed that the chemical stability of ceMoS2 was regulated by the nucleophilicities and the resultant charging effects of the anions in aquatic systems. The anions promote the dissolution of ceMoS2 by triggering a shift in the chemical potential of the ceMoS2 surface as a function of the anion nucleophilicity (i.e., charging effect). Fast charging with HCO3- and HPO42-/H2PO4- was validated by a phase transition from 1T to 2H and the emergence of MoV, and it promoted oxidative dissolution of the ceMoS2. Additionally, under sunlight, ceMoS2 dissolution was accelerated by NO3-. These findings provide insight into the ion-induced fate of ceMoS2 and the durability and risks of MoS2 nanosheets in environmental applications.

Recent technologies for glyphosate removal from aqueous environment: A critical review

The growing demand for food has led to an increase in the use of herbicides and pesticides over the years. One of the most widely used herbicides is glyphosate (GLY). It has been used extensively since 1974 for weed control and is currently classified by the World Health Organization (WHO) as a Group 2A substance, probably carcinogenic to humans. The industry and academia have some disagreements regarding GLY toxicity in humans and its effects on the environment. Even though this herbicide is not mentioned in the WHO water guidelines, some countries have decided to set maximum acceptable concentrations in tap water, while others have decided to ban its use in crop production completely. Researchers around the world have employed different technologies to remove or degrade GLY, mostly at the laboratory scale. Water treatment plants combine different technologies to remove it alongside other water pollutants, in some cases achieving acceptable removal efficiencies. Certainly, there are many challenges in upscaling purification technologies due to the costs and lack of factual information about their adverse effects. This review presents different technologies that have been used to remove GLY from water since 2012 to date, its detection and removal methods, challenges, and future perspectives.

Hybrid nanomaterial-based indirect electrochemical sensing of glyphosate in surface water: a promising approach for environmental monitoring

Glyphosate (GLY), a widely utilized pesticide, poses a significant threat to human health even at minute concentrations. In this study, we propose an innovative electrochemical sensor for the indirect detection of GLY in surface water samples. The sensor incorporates a nanohybrid material composed of multi-layer graphene decorated with gold nanoparticles (AuNPs), synthesized in a single-step electrochemical process. To ensure portability and on-site measurements, the sensor is developed on a screen-printed electrode, chosen for its integration and miniaturization capabilities. The proposed sensor demonstrates remarkable sensitivity and selectivity for GLY detection in surface water samples, with an exceptional limit of detection (LOD) of 0.03 parts per billion (ppb) in both buffer and surface water matrices. Moreover, it exhibits a remarkably high sensitivity of 0.15 μA ppb-1. This electrochemical sensor offers a promising approach for accurate GLY monitoring, addressing the urgent need for reliable pesticide detection in environmental samples. The proposed sensor showed high selectivity towards GLY, when analysed in the presence of other pesticides such as phosmet, chlorpyrifos and glufosinate-ammonium. The recovery percentages of GLY from spiked surface water samples were between 93.8 and 98.9%. The study's broader implications extend to revolutionizing the way environmental chemistry addresses pesticide contamination, water quality assessment, and sustainable management of environmental pollutants. By pushing the boundaries of detection capabilities and offering practical solutions, this research contributes to the advancement of knowledge and practices that are essential for preserving and protecting our environment.

Adsorption of glyphosate and metabolite aminomethylphosphonic acid (AMPA) from water by polymer-based spherical activated carbon (PBSAC)

Glyphosate (GLY) is the most commonly used herbicide worldwide, and aminomethylphosphonic acid (AMPA) is its main metabolite. Their occurrence in ground and surface waters causes diseases in humans, while complex physico-chemical properties hinder detection and effective removal. Polymer-based spherical activated carbon (PBSAC) can adsorb many micropollutants efficiently and, hence, overcome the shortfalls of conventional treatment methods. The static adsorption of a mixture of GLY and AMPA by PBSAC was investigated with varying PBSAC properties and relevant solution chemistry. The results show that PBSAC can remove 95% GLY and 57% AMPA from an initial concentration of 1 µg/L at pH 8.2. PBSAC properties (size, activation level, and surface charge) have a strong influence on herbicide removal, where surface area plays a key role. Low to neutral pH favors non-charge interactions and results in good adsorption, while higher temperatures equally enhance GLY/AMPA adsorption by PBSAC. The work demonstrated the effective removal of GLY to meet the European guideline concentration (0.1 µg/L), while AMPA could not be removed to the required level.

Adsorptive behavior of multi-walled carbon nanotubes immobilized magnetic nanoparticles for removing selected pesticides from aqueous matrices

The present work synthesized two new materials of functionalized multi-walled carbon nanotubes (MWCNT-OH and MWCNT-COOH) impregnated with magnetite (Fe₃O₄) using solution precipitation methodology. The resulting MWCNT-OH-Mag and MWCNT-COOH-Mag materials were characterized by scanning electron microscopy coupled with energy dispersion X-ray spectroscopy, Fourier transform infrared, X-ray diffraction, atomic force microscopy, and electrical force microscopy. The characterization results indicate that the -OH functional groups in the MWCNT interact effectively with magnetite iron favoring impregnation and indicating the regular distribution of nanoparticles on the surface of the synthesized materials. The adsorption efficiency of the MWCNT-OH-Mag and MWCNT-COOH-Mag materials was tested using the pollutants 2,4-D and Atrazine. Over batch studies carried out under different pH ranges, it was found that the optimal condition for 2,4-D adsorption was at pH 2, while for Atrazine, it was found at pH 6. The rapid adsorption kinetics of 2,4-D and Atrazine reaches equilibrium within 30 min. The pseudo-first-order model described 2,4-D adsorption well. The General-order model described better atrazine adsorption. The magnetically doped adsorbent functionalized with -OH surface groups (MWCNT-OH-Mag) demonstrated superior adsorption performance and increased Fe-doped sites. The Sips model described the adsorption isotherms accurately. MWCNT-OH-Mag presented the greatest adsorption capacity at 51.4 and 47.7 mg g^-1 for 2,4-D and Atrazine, respectively. Besides, electrostatic forces and complexation rule the molecular interactions between metals and pesticides. The leaching and regeneration tests of the synthesized materials indicate high stability in an aqueous solution. Furthermore, experiments with wastewater samples contaminated with the model pollutants indicate that the novel adsorbents are highly promising for enhancing water purification by adsorptive separation.

Effective Removal of Glyphosate from Aqueous Systems Using Synthesized PEG-Coated Calcium Peroxide Nanoparticles: Kinetics Study, H2O2 Release Performance and Degradation Pathways

Glyphosate (N-phosphonomethyl glycine) is a non-selective, broad-spectrum organophosphate herbicide. Its omnipresent application with large quantity has made glyphosate as a problematic contaminant in water. Therefore, an effective technology is urgently required to remove glyphosate and its metabolites from water. In this study, calcium peroxide nanoparticles (nCPs) were functioned as an oxidant to produce sufficient hydroxyl free radicals (·OH) with the presence of Fe²⁺ as a catalyst using a Fenton-based system. The nCPs with small particle size (40.88 nm) and high surface area (28.09 m²/g) were successfully synthesized via a co-precipitation method. The synthesized nCPs were characterized using transform infrared spectroscopy (FTIR), X-ray diffractometry (XRD), Brunauer-Emmett-Teller analysis (BET), dynamic light scattering (DLS), and field emission scanning electron microscopy (FESEM) techniques. Under the given conditions (pH = 3.0, initial nCPs dosage = 0.2 g, Ca²⁺/Fe²⁺ molar ratio = 6, the initial glyphosate concentration = 50 mg/L, RT), 99.60% total phosphorus (TP) removal and 75.10% chemical oxygen demand (COD) removal were achieved within 75 min. The degradation process fitted with the Behnajady-Modirshahla-Ghanbery (BMG) kinetics model. The H₂O₂ release performance and proposed degradation pathways were also reported. The results demonstrated that calcium peroxide nanoparticles are an efficient oxidant for glyphosate removal from aqueous systems.

A review on the applicability of adsorption techniques for remediation of recalcitrant pesticides

Pesticide has revolutionised the agricultural industry by reducing yield losses and by enhancing productivity. But indiscriminate usage of such chemicals can negatively impact human health and ecosystem balance as certain pesticides can be recalcitrant in nature. Out of some of the suggested sustainable techniques to remove the pesticide load from the environment, adsorption is found to be highly efficient and can also be implemented on a large scale. It has been observed that natural adsorption that takes place after the application of the pesticide is not enough to reduce the pesticide load, hence, adsorbents like activated carbon, plant-based adsorbents, agricultural by-products, silica materials, polymeric adsorbents, metal organic framework etc are being experimented upon. It is becoming increasingly important to choose adsorbents which will not leave any secondary pollutant after treatment and the cost of production of such adsorbent should be feasible. In this review paper, it has been established that certain adsorbent like biochar, hydrochar, resin, metal organic framework etc can efficiently remove pesticides namely chlorpyrifos, diazinon, 2,4-Dichlorophenoxyacetic Acid, atrazine, fipronil, imidacloprid etc. The mechanism of adsorption, thermodynamics and kinetic part have been discussed in detail with respect to the pesticide and adsorbent under discussion. The reason behind choosing an adsorbent for the removal of a particular pesticide have also been explained. It is further highly recommended to carry out a cost analysis before implementing an absorbent because inspite of its efficacy, it might not be cost effective to use it for a particular type of pesticide or contaminant.

Microorganisms@aMIL-125 (Ti): An Amorphous Metal-Organic Framework Induced by Microorganisms and Their Applications

Amorphous metal-organic framework (aMOF)-based materials have attracted considerable attention as an emerging class of nanomaterials. Herein, novel microorganisms@aMIL-125 (Ti) composites including yeast@aMIL-125 (Ti), PCC 6803@aMIL-125 (Ti), and Escherichia coli@aMIL-125 (Ti) composites were respectively synthesized by self-assembling aMOFs on the microorganisms' surface. The functional groups on the microorganisms' surface induced structural defects and participated in the formation of aMIL-125 (Ti) composites. Finally, the application of microorganisms@aMIL-125 (Ti) composites for the removal of glyphosate from aqueous solution was selected as a model reaction to illustrate their potential for environmental protection. The present method is not only economical but also has other advantages including ease of operation, environmentally friendly assay, and high adsorption. The maximum adsorption capacity of aMIL-125 (Ti) was 1096.25 mg g^-1, which was 1.74 times that of crystalline MIL-125 (Ti). Therefore, the microorganisms@aMOFs composites will have broad application prospects in energy storage, drug delivery, catalysis, adsorbing toxic substances, sensing, encapsulating and delivering enzymes, and in other fields.

Efficient removal of glyphosate from aqueous solutions by adsorption on Mg-Al-layered double oxides: thermodynamic, kinetic, and mechanistic investigation

Up to 90% of glyphosate was removed in 40 min by a 2:1 Mg2Al-layered double oxide (LDO) at pH 10, and the adsorption kinetics fitted a pseudo-second-order law. The adsorption isotherms were type L, and the Langmuir model best fitted the experimental data, with qmax of 158.22 μg/mg at 25 °C. The intraparticle diffusion model suggested that the adsorption process is dependent on the thickness and formation of the film at the solution/solid interface. The XRD results excluded the intercalation of glyphosate anions, and FTIR along with solid-state 13C and 31P MAS NMR confirmed that the glyphosate anions interact through the carboxylate and/or phosphonate moieties, both in end-on and side-on modes to the LDO surface. Glyphosate removal was also investigated in the presence of different anionic species, and simultaneous adsorption showed that carbonate and phosphate ions strongly influence glyphosate removal.

Reduced graphene oxide on silver nanoparticle layers-decorated titanium dioxide nanotube arrays as SERS-based sensor for glyphosate direct detection in environmental water and soil

When glyphosate, a widely used organophosphate herbicide in agricultural applications, contaminates the environment, it could lead to chronic harm to human health. Herein, an efficient, air-stable and reusable surface-enhanced Raman scattering (SERS) substrate was designed to be an analytical tool for direct determination of glyphosate. A vertical heterostructure of reduced graphene oxide (rGO)-wrapped dual-layers silver nanoparticles (AgNPs) on titania nanotube (TiO2 NTs) arrays was constructed as a SERS substrate. The TiO2 NTs/AgNPs-rGO exhibited high SERS performance for methylene blue detection, offering an analytical enhancement factor (AEF) as large as 7.1 × 108 and the limit of detection (LOD) as low as 10-14 M with repeatability of 4.4 % relative standard deviation (RSD) and reproducibility of 2.0 % RSD. The sensor was stable in ambient and was reusable after photo-degradation. The designed sensor was successfully applied for glyphosate detection with a LOD of 3 µg/L, which is below the maximum contaminant level of glyphosate in environmental water, as recommended by the U.S. EPA and the European Union. A uniqueness of this study is that there is no significant difference between the real-world applications of the SERS sensor on direct glyphosate analysis in environmental samples compared to an analysis using ultra-high performance liquid chromatography.

Glyphosate Pollution Treatment and Microbial Degradation Alternatives, a Review

Glyphosate is a broad-spectrum herbicide extensively used worldwide to eliminate weeds in agricultural areas. Since its market introduction in the 70's, the levels of glyphosate agricultural use have increased, mainly due to the introduction of glyphosate-resistant transgenic crops in the 90's. Glyphosate presence in the environment causes pollution, and recent findings have proposed that glyphosate exposure causes adverse effects in different organisms, including humans. In 2015, glyphosate was classified as a probable carcinogen chemical, and several other human health effects have been documented since. Environmental pollution and human health threats derived from glyphosate intensive use require the development of alternatives for its elimination and proper treatment. Bioremediation has been proposed as a suitable alternative for the treatment of glyphosate-related pollution, and several microorganisms have great potential for the biodegradation of this herbicide. The present review highlights the environmental and human health impacts related to glyphosate pollution, the proposed alternatives for its elimination through physicochemical and biological approaches, and recent studies related to glyphosate biodegradation by bacteria and fungi are also reviewed. Microbial remediation strategies have great potential for glyphosate elimination, however, additional studies are needed to characterize the mechanisms employed by the microorganisms to counteract the adverse effects generated by the glyphosate exposure.

Regenerable magnetic aminated lignin/Fe3O4/La(OH)3 adsorbents for the effective removal of phosphate and glyphosate

Phosphates and organophosphorus cause environmental pollution, and excessive phosphate leads to water eutrophication. Glyphosate, an organophosphorus herbicide, harms the environment and human health. In this study, regenerable magnetic AL/Fe₃O₄/La(OH)₃ adsorbents were developed by modifying Fe₃O₄ and La(OH)₃ on aminated lignin (AL) for phosphate and glyphosate removal. The adsorption capacity for phosphate and glyphosate reached 60.36 mg g^-1 and 83.87 mg g^-1 when the initial concentrations were 150 mg L^-1 and 250 mg L^-1, respectively. The thermodynamic data showed that adsorption is a spontaneous and endothermic process. Adsorption can be applied at pH values ranging from 3 to 11 and is more suitable under acidic conditions. Fe₃O₄ and La(OH)₃ both enhanced the adsorption capacities of phosphate and glyphosate. Phosphate and glyphosate compete slightly when coexisting in the adsorption process at low concentrations. Due to the magnetic properties of Fe₃O₄, the adsorbents can be separated rapidly and effectively with an external magnetic field. 89% adsorption capacity remained after four adsorption-desorption recycles. Thus, AL/Fe₃O₄/La(OH)₃ shows potential for phosphate and glyphosate removal as an effective and reusable adsorbent.

Film-like bacterial cellulose/cyclodextrin oligomer composites with controllable structure for the removal of various persistent organic pollutants from water

The adsorptive removal of persistent organic pollutants (POPs) is reckoned as a simple, convenient, and practical technology, especially in decentralized systems and remote areas. For this purpose, it is important to design new adsorbents, with controllable structure and convenient shape, for the highly efficient removal of POPs. In this study, we describe a strategy for film-like water purifier, prepared by loading cyclodextrin (CD) oligomer onto the ultrafine nanofibers of 3D bacterial cellulose. The optimum product exhibits remarkable removal ability toward various target pollutants such as phenol, bisphenol A (BPA), glyphosate and 2,4-Dichlorophenol (2,4-DCP), with capacities higher than most adsorbents including porous carbon based materials reported previously. Moreover, our sample demonstrated stable adsorption ability over a broad pH range and under more complex water conditions, and more importantly excellent reusability. A rough cost analysis highlights the commercial potential of our sample. We reckon our study provides new insight for the design of adsorbent with high yet stable adsorption ability and controllable structure. Furthermore, the product can be used to treat actual sewage with its convenient film-like shape and excellent performance, which improves its potential in complex systems and large-scale applications.

Ecotoxicology of glyphosate and recent advances in its mitigation by adsorption

Glyphosate (N-[phosphonomethyl]glycine) is one of the most popular herbicides now used in agricultural practice. The aim of this paper was to discuss the research progress and innovations in recent years on the mitigation of glyphosate (GLY) from aqueous media by adsorption. The ecotoxicology of GLY was discussed in the domain of its chronic and sub-chronic toxicity, genotoxicity, reproductive toxicity, and carcinogenicity, and potential risks of food contamination were discussed. It was observed that polymers and resins are the best class of adsorbents for GLY adsorption from aqueous media. GLY adsorption was best fit to either Freundlich or Langmuir isotherm depending on the nature of the adsorbent. The pseudo-second-order kinetics was also the best fit for modelling the kinetics of GLY adsorption. A review of the thermodynamics revealed that GLY adsorption was usually spontaneous and exothermic. Research trends and knowledge gaps are in the area of chemical mobility in environmental systems (especially in the presence of other chemical species), the use of heavy metal-laden adsorbent and molecular modelling. Furthermore, it was observed that the ecotoxicology of GLY still has some contentious areas where there is no conclusive stance.

Technologies Employed in the Treatment of Water Contaminated with Glyphosate: A Review

Glyphosate [N-(phosphonomethyl)-glycine] is a herbicide with several commercial formulations that are used generally in agriculture for the control of various weeds. It is the most used pesticide in the world and comprises multiple constituents (coadjutants, salts, and others) that help to effectively reach the action's mechanism in plants. Due to its extensive and inadequate use, this herbicide has been frequently detected in water, principally in surface and groundwater nearest to agricultural areas. Its presence in the aquatic environment poses chronic and remote hazards to human health and the environment. Therefore, it becomes necessary to develop treatment processes to remediate aquatic environments polluted with glyphosate, its metabolites, and/or coadjutants. This review is focused on conventional and non-conventional water treatment processes developed for water polluted with glyphosate herbicide; it describes the fundamental mechanism of water treatment processes and their applications are summarized. It addressed biological processes (bacterial and fungi degradation), physicochemical processes (adsorption, membrane filtration), advanced oxidation processes-AOPs (photocatalysis, electrochemical oxidation, photo-electrocatalysis, among others) and combined water treatment processes. Finally, the main operating parameters and the effectiveness of treatment processes are analyzed, ending with an analysis of the challenges in this field of research.

D151 resin preloaded with Fe3+ as a salt resistant adsorbent for glyphosate from water in the presence 16% NaCl

D151 resin preloaded with Fe3+ [denoted as R-Fe3+] was to investigate R-Fe3+ as an adsorbent for glyphosate from water in the presence high concentration of salt. The adsorption mechanism revealed the coordination of Fe3+ inside R-Fe3+ with O atoms of P-O and N atoms in glyphosate molecule. The adsorption capacity of glyphosate by R-Fe3+ was much larger than that of D151 resin preloaded with Ni2+, Cu2+, Na+ and H+. Even in glyphosate solutions containing 16% NaCl, R-Fe3+ showed the constant adsorption capacity of glyphosate. The result provided the first evidence of R-Fe3+ as a salt resistant adsorbent for glyphosate. The adsorption capacity of glyphosate was the maximum at pH 3.35. The adsorption thermodynamics showed that the adsorption of glyphosate by R-Fe3+ was the ligand exchange of glyphosate and water. The maximum coordination ratio of glyphosate to Fe3+ inside R-Fe3+ was 1:1. The maximum adsorption capacity of glyphosate by R-Fe3+ was up to 481.85 mg/g, which is much higher than that of other reported adsorbents in the presence 16% NaCl. 2  mol/L NaOH, 2  mol/L H2SO4 and 2  mol/L Fe2(SO4)3 could all be used to achieve over 97% regeneration of R-Fe3+.

Highly enhanced adsorption performance of tetracycline antibiotics on KOH-activated biochar derived from reed plants

Organic pollutants in water are an increasingly prominent problem. Given this challenge, this study investigated the high adsorption capacity of reed-based biochar for use as an adsorbent using the potassium hydroxide (KOH) activation method. We investigated the performance and mechanism of reed-based biochar with respect to the adsorption of a significant contaminant of emerging concern, tetracycline (TC). The effects of pH, contact time, temperature, and initial pollution concentration on the adsorption rate were investigated in detail. The experimental results suggest that the internal structure of activated biochar was loose and porous, and the specific surface area (BET) increased by 194.08 times, reaching 965.31 m2 g-1 after KOH activation. The biochar surface was electronegative, due to the ionization of oxygen-containing functional groups, such as hydroxyl (-OH) and carboxyl (-COOH) groups. Solution pH had only a weak influence on TC adsorption; neutral conditions favored adsorption. The adsorption kinetics and isotherms were represented well by the pseudo-second-order and Freundlich models, respectively. The chemical multilayer adsorption may play an important role in TC adsorption, which was a spontaneous endothermic reaction. The adsorption process occurred more easily after KOH activation and the adsorption capacity of biochar improved by more than 20 times. These results indicate that preparing reed-derived biochar using KOH activation is an effective way to reduce pollution and utilize a waste resource.

Adsorption of phenanthrene and 1-naphthol to graphene oxide and L-ascorbic-acid-reduced graphene oxide: effects of pH and surfactants

In this study, reduced graphene oxide (RGO) was synthesized by _L-ascorbic acid reduction, which was a relatively mild and environmental friendly reduction method, and the adsorption of organic contaminants was compared to graphene oxide (GO) to probe the potential adsorption mechanisms. The morphology properties of GO and RGO were characterized by X-ray photoelectron spectroscopy (XPS), Fourier transform infrared transmission (FTIR), Raman spectrometer, transmission electron microscope (TEM), and scanning electron microscopy (SEM). The adsorption affinities of GO and RGO for phenanthrene and 1-naphthol were studied in batch experiments. The effects of pH and surfactants were also assessed. The results demonstrated that RGO reduced by _L-ascorbic acid show significantly greater adsorption affinity for both phenanthrene and 1-naphthol than GO, and even greater than most of RGOs that reduced by the strong reductive reagents. This was mainly attributed to the hydrophobic interaction, π-π interaction, and H-bonding between graphene sheets and organic contaminants. Both GO and RGO showed stronger adsorption to phenanthrene than to 1-naphthol. The adsorption of 1-naphthol increased with decreasing pH and reached a maximum around pH = 7.34. The surfactants, sodium dodecyl benzene sulfaonate (SDBS) and cetyltrimethyl ammonium bromide (CTAB), had negligible influence on adsorption to GO. Note that CTAB significantly inhibited the adsorption of phenanthrene/1-naphthol on RGO, which could be attributed to the pore blockage effect. In addition, RGO could be regenerated and reused with high recyclability over five cycles. The present study suggests that RGO obtained via _L-ascorbic acid reduction can be deemed as a promising material for organic contaminated wastewater treatment.