Synthesis and characterization of ZnO decorated reduced graphene oxide (ZnO-rGO) and evaluation of its photocatalytic activity toward photodegradation of methylene blue

Sustainable conversion of polyethylene plastic bottles into terephthalic acid, synthesis of coated MIL-101 metal-organic framework and catalytic degradation of pollutant dyes

Persistent environmental colored compounds, resistant to biodegradation, accumulate and harm eco-systems. Developing effective methods to break down these pollutants is crucial. This study introduces Ag-MIL-101 (Ag-MIL-101) as a composite and reusable catalyst that efficiently degrades specific colored organic pollutants (COPs) like Methylene blue (MB), 4-Nitrophenol (4-NP), and 4-Nitroaniline (4-NA) using sodium borohydride at room temperature. The MIL-101 was synthesized using Terephthalic acid (TPA) derived from the degradation of Polyethylene Terephthalate (PET) plastic waste, with the assistance of zinc chloride. To further investigation, the kinetics of degradation reaction was studied under optimized conditions in the presence of Ag-MIL-101 as catalyst. Our results demonstrated the remarkable efficiency of the degradation process, with over 93% degradation achieved within just 8 min. The catalyst was characterized using FTIR, XRD, FESEM, and TEM. In this study, the average particle size of Ag-MIL-101 was determined using SEM and XRD analysis. These methods allow us to accurately and precisely determine the particle size. We determined the reaction rate constants for the degradation of each COP using a pseudo first-order kinetic equation, with values of 0.585, 0.597 and 0.302 min-1 for MB, 4-NP, and 4-NA, respectively. We also evaluated the recyclability of the catalyst and found that it could be reused for up to three cycles with only a slight decrease in efficiency (10-15%). Overall, our findings highlight the promising application of Ag-MIL-101 as an effective catalyst for the degradation of COPs, emphasizing the importance of optimizing reaction conditions to achieve enhanced efficiency.

Construction and mechanistic insights of a novel ZnO functionalized rGO composite for efficient adsorption and reduction of Cr(VI)

A series of ZnO decorated reduced graphene oxide (rGO) (ZnrGOx) with different doping ratios were synthesized by the alkaline hydrothermal method using graphene oxide (GO) and Zn(NO3)2·6H2O as precursors, and subsequently used for the adsorption study of Cr(VI) in water. The morphology, crystalline phase structure, and surface elemental properties of ZnrGOx composites were revealed by XRD, SEM, BET, FT-IR, and XPS characterizations. The results showed that ZnO nanoparticles can be clearly seen on the surface of layered rGO. Meanwhile, as the doping rate increased, the C = C double bonds were broken and more carboxylic acid groups formed in ZnrGOx. In addition, the ZnrGO0.1 composite had the most excellent adsorption performance and good stability, and reusability. The adsorption removal rate of Cr(VI) can reach 99%, and the maximum adsorption amount of Cr(VI) was 68.9655 mg/g in 3 h. The isothermal and kinetic model simulations showed that Cr(VI) adsorption on ZnrGO0.1 composite is a chemical adsorption process, spontaneous and endothermic. Based on the concentrations of different valence states of Cr in the solid and liquid phases, 40% of Cr(VI) was reduced to Cr(III) on the surface of ZnrGO0.1 composite. Moreover, the adsorption-reduction mechanisms of Cr(VI) on ZnrGO0.1 composite were further elucidated. The ZnrGO0.1 composite manifested great potential as an efficient adsorbent for Cr(VI) removal.

Development of environmentally friendly catalyst Ag-ZnO@cellulose acetate derived from discarded cigarette butts for reduction of organic dyes and its antibacterial applications

The release of harmful organic dyes from different industries besides its degradation products is a major contributor to environmental contamination. The catalytic reduction of these organic pollutants using nanocomposites based on polymeric material presents potential advantages for the environment. In this study, novel nanocomposite based on cellulose acetate (CA)-derived from discharged cigarette butts and zinc oxide nanoparticles (ZnO NPs) was prepared utilizing a very simple and low-cost solution blending method and used as support for silver nanoparticles (Ag NPs). A simple reduction method was used to anchor different percentages of Ag NPs on the ZnO@CA nanocomposite surface via utilizing sodium borohydride as a reducing agent. The Ag-ZnO@CA nanocomposite was characterized using X-ray diffraction, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and transmission electron microscopy. The TEM analysis showed spherical Ag NPs, with an average diameter of ∼17.6 nm, were uniformly anchored on the ZnO@CA nanocomposite surface. The prepared nanocomposites were evaluated as catalysts for the reduction of organic dyes in water. It was found that 10 % Ag-ZnO@CA nanocomposite showed a remarkable reduction of Rhodamine B (RhB), Rhodamine 6G (Rh6G), Methylene Blue (MB), and Sunset Yellow (SY) dyes in short time. In the presence of this nanocomposite, the rate constant, kapp values for RhB, Rh6G, MB, and SY were 0.3498 min-1, 1.51 min-1, 0.2292 min-1, and 0.733 min-1, respectively. This nanocomposite was recovered and reused in five successive cycles, with a negligible loss of its activity. Furthermore, the nanocomposites demonstrated moderate antibacterial activity toward Staphylococcus aureus and Escherichia coli. Thus, this study directed attention on recycling of waste material to a valuable nanocomposite and its applications in environmental protection.

Stepwise reduction of graphene oxide and studies on defect-controlled physical properties

Graphene oxide (GO) is a monolayer of oxidized graphene which is a convenient and potential candidate in a wide range of fields of applications like electronics, photonics, optoelectronics, energy storage, catalysis, chemical sensors, and many others. GO is often composed of various oxygen-containing groups such as hydroxyl, carboxyl, and epoxy. One appealing method for achieving graphene-like behavior with sp2 hybridized carbon is the reduction of GO i.e. formation of reduced graphene oxide (RGO). A stepwise reduction GO to form a family of RGO, containing various quantities of oxygen-related defects was carried out. Herein, the defects related chemical and physical properties of GO and the RGO family were studied and reported in an effort to understand how the properties of RGO vary with the reduction rate. Although there are several reports on various features and applications of GO and RGO but a systematic investigation of the variation of the physical and chemical properties in RGO with the varying quantities of oxygeneous defects is imperative for the engineered physical properties in achieving the desired field of applications. We have attempted to look at the role of sp2 and sp3 carbon fractions, which are present in RGO-based systems, and how they affect the electrical, optoelectronic, and adsorption characteristics.

Dynamics of reduced graphene oxide: synthesis and structural models

Technological advancements are leading to an upsurge in demand for functional materials that satisfy several of humankind's needs. In addition to this, the current global drive is to develop materials with high efficacy in intended applications whilst practising green chemistry principles to ensure sustainability. Carbon-based materials, such as reduced graphene oxide (RGO), in particular, can possibly meet this criterion because they can be derived from waste biomass (a renewable material), possibly synthesised at low temperatures without the use of hazardous chemicals, and are biodegradable (owing to their organic nature), among other characteristics. Additionally, RGO as a carbon-based material is gaining momentum in several applications due to its lightweight, nontoxicity, excellent flexibility, tuneable band gap (from reduction), higher electrical conductivity (relative to graphene oxide, GO), low cost (owing to the natural abundance of carbon), and potentially facile and scalable synthesis protocols. Despite these attributes, the possible structures of RGO are still numerous with notable critical variations and the synthesis procedures have been dynamic. Herein, we summarize the highlights from the historical breakthroughs in understanding the structure of RGO (from the perspective of GO) and the recent state-of-the-art synthesis protocols, covering the period from 2020 to 2023. These are key aspects in the realisation of the full potential of RGO materials through the tailoring of physicochemical properties and reproducibility. The reviewed work highlights the merits and prospects of the physicochemical properties of RGO toward achieving sustainable, environmentally friendly, low-cost, and high-performing materials at a large scale for use in functional devices/processes to pave the way for commercialisation. This can drive the sustainability and commercial viability aspects of RGO as a material.

Photocatalytic degradation of dissolved organic matter in landfill leachate by heterostructural ZnO-rGO composite catalysts

The dissolved organic matter (DOM) in landfill pollutes not only the landfill and surroundings, but also the environment far away from the landfill by infiltrating into the soil and/or flowing on the ground surface. Developing an efficient photocatalyst to degrade DOM is an interesting topic. Herein, the catalysts composed of ZnO and reduced graphene oxide (ZnO-rGO) with different morphologies were fabricated with a two-step hydrothermal method. The phase composite and microstructure were analyzed, and the degradation efficiency of the DOM under ultraviolet light was investigated. Three kinds of ZnO-rGO composite catalysts with different morphologies were successfully synthesized, and rGO was coated on the ZnO surface to form heterostructural composite catalysts. The catalyst powders have similar Raman and FT-IR spectra, but have different specific surface areas and band gaps. The degradation efficiency of DOM by ZnO-rGO composites is higher than that of pure ZnO powder. Compared to pure ZnO, ZnO-rGO composite catalysts contain more oxygen vacancies and a narrower band gap, and the heterostructure is beneficial for accelerating electron separation, inhibiting electron recombination.

ZnO/Graphene Composite from Solvent-Exfoliated Few-Layer Graphene Nanosheets for Photocatalytic Dye Degradation under Sunlight Irradiation

ZnO/graphene nanocomposites were prepared using a facile approach. Graphene nanosheets were prepared by ultrasonication-based liquid phase exfoliation of graphite powder in a low boiling point organic solvent, 1,2-Dichloroethane, for the preparation of ZnO/graphene nanocomposites. Structural properties of the synthesized ZnO/graphene nanocomposites were studied through powder XRD and micro-Raman analysis. The characteristic Raman active modes of ZnO and graphene present in the micro-Raman spectra ensured the formation of ZnO/graphene nanocomposite and it is inferred that the graphene sheets in the composites were few layers in nature. Increasing the concentration of graphene influenced the surface morphology of the ZnO nanoparticles and a flower shape ZnO was formed on the graphene nanosheets of the composite with high graphene concentration. The efficiencies of the samples for the photocatalytic degradation of Methylene Blue dye under sunlight irradiation were investigated and 97% degradation efficiency was observed. The stability of the nanocomposites was evaluated by performing five cycles, and 92% degradation efficiency was maintained. The observed results were compared with that of ZnO/graphene composite derived from other methods.

Biochar from Cyperus alternifolius Linn.: from a waste of phytoremediation processing to efficient depolluting agent

Phytoremediation is one of the most powerful and viable solutions for developing countries to clean the soil and water bodies from metallic pollutants. Cyperus alternifolius Linn. (CAL), a tropical wetland plant, has been widely researched for removing harmful contaminants due to its hyperaccumulation ability. However, the waste biomass of phytoremediation processing may risk secondary environmental pollution. Thus, the preparation and application of biochar from metal-contaminated plants can be considered a new approach. In a 60-day experiment, CAL plants were irrigated with different concentrations of Zn(II) (200, 700, 1200, 1700, and 2200 mg·L^-1), and then the plants were converted into biochar via the pyrolysis process. The characteristics of biochar including of surface composition and morphology, phase formation, and optical property were analyzed. The biochar enriched with Zn(II) at 1200 mg·L^-1 had a bandgap value of 3.17 eV and consisted of carbon microparticles intermingled with ZnO and SiO₂ nanoparticles. Furthermore, the adsorption and photocatalysis of the biochar were studied in the discolouration of methylene blue (MB), as a test reaction, with the maximum MB removal capacities of 55.2 mg·g^-1. Such results will serve as the basis for new research aiming at the potential for reusing metal-contaminated plants to produce efficient depolluting biochar.

Highly Efficient Photocatalysts for Methylene Blue Degradation Based on a Platform of Deposited GO-ZnO Nanoparticles on Polyurethane Foam

The demand for reactive dyes in industries has increased rapidly in recent years, and producing a large quantity of dye-containing effluent waste contaminates soils and water streams. Current efforts to remove these harmful dyes have focused on utilizing functionalized nanomaterials. A 3D polyurethane foam loaded with reduced graphene oxide (rGO) and ZnO nanocomposite (PUF/rGO/ZnO) has been proposed as an efficient structural design for dye degradation under the influence of visible light. The proposed structure was synthesized using a hydrothermal route followed by microwave irradiation. The resultant 3D PUF/rGO/ZnO was examined and characterized by various techniques such as XRD, FTIR, SEM, EDAX, BET, and UV-visible spectroscopy. SEM data illustrated that a good dispersion and embedment of the rGO/ZnO NPs within the PUF matrix occurred. The adsorption capacity for neat PUF showed that around 20% of the Methylene blue (MB) dye was only adsorbed on its surface. However, it was found that an exceptional adsorption capacity for MB degradation was observed when the rGO/ZnO NPs inserted into the PUF, which initially deteriorated to ~ 70 % of its initial concentration. Notably, the MB dye was completely degraded within 3 h.

Synthesis, Characterization, and Solar Photo-Activation of Chitosan-Modified Nickel Magnetite Bio-Composite for Degradation of Recalcitrant Organic Pollutants in Water

Photocatalysis is a promising process for decomposing harmful organic pollutants in water. In this study, solar/photocatalytic degradation of two model azo dyes, i.e., methylene blue (MB) and methyl red (MR), in water usinga nanostructured chitosan-modified nickel magnetite (CS-NM) bio-composite was investigated. The CS-NM bio-composite was synthesized through a co-precipitation method and characterized by Fourier transform infrared (FTIR), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), thermogravimetry (TGA), and UV-Vis spectroscopy. FTIR analysis showed the uniform incorporation and conjugation of nickel magnetite (NM) into the chitosan (CS) polymer matrix. SEM showed that the average particle size was 0.5 μm. The TGA results revealed the good thermal stability of the prepared bio-composite at 300 °C. The point of zero charge was calculated as 7.5. The effect of water quality and process parameters, such as concentration of dyes, catalyst dose, solution pH, and temperatures, was investigated, for application purposes. The solar/CS-NM photocatalysis resulted in 99 and 96% degradation of individual MB and MR (C0 = 50 ppm), respectively, in 90 min. The degradation of MB and MR by solar/CS-NM photocatalysis followed pseudo-first-order kinetics, with observed rate constants (k) of 0.077 and 0.072 min−1, respectively. The CS-NM photocatalyst showed high recyclability, represented by only a 4–6% loss in the photocatalytic efficiency, after four cycles. The results showed that solar/CS-NM photocatalysis is an efficient technique for degrading recalcitrant organic pollutants, such as azo dyes, in water environments.

Zn-doped Bi2MoO6 supported on reduced graphene oxide with increased surface active sites for degradation of ciprofloxacin

The reduced graphene oxide supported Zn-doped Bi₂MoO₆ nanocomposites (Zn_xBi_2-xMoO₆/RGO) are synthesized by an easy one-step solvothermal method for the rapid degradation of ciprofloxacin (CIP). Characterization analyses show that Bi₂MoO₆ nanosheets are uniformly supported on RGO, for which the agglomeration of Bi₂MoO₆ is effectively inhibited, leading to more exposure of surface active sites. The degradation rate of Zn_0.1Bi_1.9MoO₆/RGO₅ on CIP reached 90% after 120 min of visible light irradiation, which was 10.4 times the rate of unsupported Bi₂MoO₆. Zn doping and RGO loading synergistically reduce the recombination rate of photogenerated electron-hole pairs and result in the enhanced photocatalytic performance. Compared with previously reported catalysts, Zn_0.1Bi_1.9MoO₆/RGO₅ can get higher degradation efficiency with shorter time and less dosage. In addition, after five cycles, the degradation efficiency is maintained at about 85%, showing perfect cycling stability of Zn_0.1Bi_1.9MoO₆/RGO₅. Photocatalytic mechanism suggests that the photogenerated •O₂^- and h⁺ are main species for degrading CIP based on Zn_xBi_2-xMoO₆/RGO complex.

Photocatalysis: an effective tool for photodegradation of dyes-a review

The disposal of dye-contaminated wastewater is a major concern around the world for which a variety of techniques are used for its treatment. The photocatalytic treatment of dye-contaminated wastewater is one of the treatment methods. Semiconductor-assisted photocatalytic treatment of dye-contaminated wastewater has gained pronounced attention recently. This review outlines the recent advancements in the photocatalytic treatment of dye-contaminated wastewater. The photocatalytic degradation of dyes follows three types of mechanisms: (1) dye sensitization through charge injection, (2) indirect dye degradation through oxidation/reduction, and (3) direct photolysis of dye. Several experimental parameters like initial concentration of dyes, pH, and catalyst dosage significantly affect the photocatalytic degradation of dyes. The photocatalytic materials can be categorized into three generations. The single-component (e.g., ZnO, TiO₂) and multiple component semiconductor metal oxides (e.g., ZnO-TiO₂, Bi₂O₃-ZnO) are categorized as first-generation and second-generation photocatalysts, respectively. The photocatalysts dispersed on an inert solid substrate (e.g., Ag-Al₂O₃, ZnO-C) are classified as third-generation photocatalysts. Finally, we reviewed the challenges that affect the photocatalytic degradation of dyes.

Enhanced photocatalytic activities of a hierarchical ZnO/V2C MXene hybrid with a close coupling heterojunction for the degradation of methyl orange, phenol and methylene blue dye

A hierarchical ZnO/V2C MXene hybrid exhibited enhanced photocatalytic performance due to its close coupling heterojunction facilitating photo-generated carrier transfer.