Side-chain engineering of high-efficiency conjugated polymer photovoltaic materials

Optimization of Charge Management and Energy Loss in All-Small-Molecule Organic Solar Cells

All-small-molecule organic solar cells (ASM-OSCs) have received tremendous attention in recent decades because of their advantages over their polymer counterparts. These advantages include well-defined chemical structures, easy purification, and negligible batch-to-batch variation. Remarkable progress with a power conversion efficiency (PCE) of over 17% has recently been achieved with improved charge management (FF × JSC) and reduced energy loss (Eloss). Morphology control is the key factor in the progress of ASM-OSCs, which remains a significant challenge because of the similarities in the molecular structures of the donors and acceptors. In this review, the effective strategies for charge management and/or Eloss reduction from the perspective of effective morphology control are summarized. The aim is to provide practical insights and guidance for material design and device optimization to promote further development of ASM-OSCs to a level where they can compete with or even surpass the efficiency of polymer solar cells.

Stereoisomeric Non-Fullerene Acceptors-Based Organic Solar Cells

Chiral alkyl chains are ubiquitously observed in organic semiconductor materials and can regulate solution processability and active layer morphology, but the effect of stereoisomers on photovoltaic performance has rarely been investigated. For the racemic Y-type acceptors widely used in organic solar cells, it remains unknown if the individual chiral molecules separate into the conglomerate phase or if racemic phase prevails. Here, the photovoltaic performance of enantiomerically pure Y6 derivatives, (S,S)/(R,R)-BTP-4F, and their chiral mixtures are compared. It is found that (S,S) and (R,R)-BTP-4F molecule in the racemic mixtures tends to interact with its enantiomer. The racemic mixtures enable efficient light harvesting, fast hole transfer, and long polaron lifetime, which is conducive to charge generation and suppresses the recombination losses. Moreover, abundant charge diffusion pathways provided by the racemate contribute to efficient charge transport. As a result, the racemate system maximizes the power output and minimizes losses, leading to a higher efficiency of 18.16% and a reduced energy loss of 0.549 eV, as compared to the enantiomerically pure molecules. This study demonstrates that the chirality of non-fullerene acceptors should receive more attention and be designed rationally to enhance the efficiency of organic solar cells.

Introducing a Phenyl End Group in the Inner Side Chains of A-DA'D-A Acceptors Enables High-Efficiency Organic Solar Cells Processed with Nonhalogenated Solvent

Power conversion efficiency (PCE) of organic solar cells (OSCs) processed by nonhalogenated solvents is unsatisfactory due to the unfavorable morphology. Herein, two new small molecule acceptors (SMAs) Y6-Ph and L8-Ph are synthesized by introducing a phenyl end group in the inner side chains of the SMAs of Y6 and L8-BO, respectively, for overcoming the excessive aggregation of SMAs in the long-time film forming processed by nonhalogenated solvents. First, the effect of the film forming time on the aggregation property and photovoltaic performance of Y6, L8-BO, Y6-Ph, and L8-Ph is studied by using the commonly used solvents: chloroform (CF) (rapid film forming process) and chlorobenzene (CB) (slow film forming process). It is found that Y6- and L8-BO-based OSCs exhibit a dramatic drop in PCE from CF- to CB-processed devices owing to the large phase separation, while the Y6-Ph and L8-Ph based OSCs show obviously increased PCEs Furthermore, L8-Ph-based OSCs processed by nonhalogenated solvent o-xylene (o-XY) achieved a high PCE of 18.40% with an FF of 80.11%. The results indicate that introducing a phenyl end group in the inner side chains is an effective strategy to modulate the morphology and improve the photovoltaic performance of the OSCs processed by nonhalogenated solvents.

Preparation of Efficient Organic Solar Cells Based on Terpolymer Donors via a Monomer-Ratio Insensitive Side-Chain Hybridization Strategy

Creating new donor materials is crucial for further advancing organic solar cells. Random terpolymers have been adopted to overcome shortcomings of regular alternating donor-acceptor (D-A) polymers of which the performance is often susceptible to batch-to-batch variations. In general, the properties and performance of efficient D₁ -A-D₂ -A and D-A₁ -D-A₂ terpolymers are sensitive to the D₁ /D₂ or A₁ /A₂ monomer ratios. Side-chain hybridization is a strategy to address this problem. Here, six D₁ -A-D₂ -A-type random terpolymers comprising D₁ and D₂ monomers with the same π-conjugated D unit but with different side chains were synthesized. The side chains, containing either fluorine or trialkylsilyl substituents were chosen to provide near-identical optoelectronic properties but provide a tool to create a better-optimized film morphology when blended with a non-fullerene acceptor. This strategy allows improving the device performance to over 18 %, higher than that obtained with the corresponding D₁ -A or D₂ -A bipolymers (around 17 %). Hence, side-chain hybridization is a promising strategy to design efficient D₁ -A-D₂ -A terpolymer donors that are insensitive to the D₁ /D₂ monomer ratio, which is beneficial for the scaled-up synthesis of high-performance materials.

Crystallization of D-A Conjugated Polymers: A Review of Recent Research

D-A conjugated polymers are key materials for organic solar cells and organic thin-film transistors, and their film structure is one of the most important factors in determining device performance. The formation of film structure largely depends on the crystallization process, but the crystallization of D-A conjugated polymers is not well understood. In this review, we attempted to achieve a clearer understanding of the crystallization of D-A conjugated polymers. We first summarized the features of D-A conjugated polymers, which can affect their crystallization process. Then, the crystallization process of D-A conjugated polymers was discussed, including the possible chain conformations in the solution as well as the nucleation and growth processes. After that, the crystal structure of D-A conjugated polymers, including the molecular orientation and polymorphism, was reviewed. We proposed that the nucleation process and the orientation of the nuclei on the substrate are critical for the crystal structure. Finally, we summarized the possible crystal morphologies of D-A conjugated polymers and explained their formation process in terms of nucleation and growth processes. This review provides fundamental knowledge on how to manipulate the crystallization process of D-A conjugated polymers to regulate their film structure.

Fine-Tuning of Siloxane Pendant Distance for Achieving Highly Efficient Eco-Friendly Nonfullerene Solar Cells

Side-chain engineering has been proved to show profound impact on polymer properties and blend morphology. Herein, the critical role of siloxane-terminated alkoxy side chains was revealed by a tiny decorating method through which the molar content of siloxane-terminated alkoxy side chain was fixed to 5 %, and its alkyl linker was the only tuning factor. The pentylene, heptylene, and nonylene linkers were designed and used to synthesize wide-bandgap polymers PQSi505, PQSi705, and PQSi905, respectively. Interestingly, the siloxane pendant of combinatory side chain exhibited a distinct impact on molecular packing when its branching position shifted slightly. Among the three polymers, PQSi705 had the strongest aggregation and the highest packing order. Finally, toluene-processed organic solar cells (OSCs) based on PQSi705 and Y6-BO achieved the best power conversion efficiency of 15.77 %. This work suggests that siloxane pendant can serve as a powerful modulator to enhance the photovoltaic performance of OSCs.

Material Design and Device Fabrication Strategies for Stretchable Organic Solar Cells

Recent advances in the power conversion efficiency (PCE) of organic solar cells (OSCs) have greatly enhanced their commercial viability. Considering the technical standards (e.g., mechanical robustness) required for wearable electronics, which are promising application platforms for OSCs, the development of fully stretchable OSCs (f-SOSCs) should be accelerated. Here, a comprehensive overview of f-SOSCs, which are aimed to reliably operate under various forms of mechanical stress, including bending and multidirectional stretching, is provided. First, the mechanical requirements of f-SOSCs, in terms of tensile and cohesion/adhesion properties, are summarized along with the experimental methods to evaluate those properties. Second, essential studies to make each layer of f-SOSCs stretchable and efficient are discussed, emphasizing strategies to simultaneously enhance the photovoltaic and mechanical properties of the active layer, ranging from material design to fabrication control. Key improvements to the other components/layers (i.e., substrate, electrodes, and interlayers) are also covered. Lastly, considering that f-SOSC research is in its infancy, the current challenges and future prospects are explored.

Side-Chain Engineering of Conjugated Polymers for High-Performance Organic Field-Effect Transistors

Past decades have witnessed the rapid development of conjugated polymers because of their promising semiconducting properties and applications in organic field-effect transistors (OFETs). Recent studies have shown that side-chain engineering of conjugated polymers is an efficient strategy to increase semiconducting performance. This Perspective focuses on the side-chain modulation of conjugated polymers and evaluating their effects on the performance of OFETs. The challenges and potential applications of functional high-performance OFETs through side-chain engineering are also discussed.

Novel benzo[b]thieno[2,3-d]thiophene derivatives with an additional alkyl-thiophene core: synthesis, characterization, and p-type thin film transistor performance

Newly synthesized benzo[b]thieno[2,3-d]thiophene derivatives were employed as active layers of organic field effect transistors, and these transistors showed decent electrical performance.

Toward the Rational Design of Organic Solar Photovoltaics: Application of Molecular Structure Methods to Donor Polymers

Conjugated polymers are promising candidates in the design of polymer solar cell materials with suitable electronic properties. Recent studies show that the use of different functional groups as side chain in thiophene-based polymers changes the electronic and conformation structures. Here we design new thiophene-based molecules by replacing the hydrogen attached to the backbone of P3MT with electron-donating and electron-withdrawing groups. We then calculate the HOMO, LUMO, and HOMO-LUMO energy gap to quantify the theoretical merit of the new polymers as solar absorbers and their inter-ring torsional potential to understand their suitability to link together in high conductivity, extended conjugated systems. Calculations are done with first-principles density functional theory (DFT), implemented using B3LYP with dispersion function and 6-31G(d,p) as basis set. Our results show that the HOMO-LUMO gap is sensibly lowered by donating groups and we found that the substitution of the hydrogen with -NH2, and -F gives an energy gap lower than the energy gap of P3MT. The lowest energy gap was found when substituting with -NH2. Electron-withdrawing groups lower the HOMO, with the overall lowest found when -NO2 is used. -COCl, -CONH2, and -Cl give a steric hindrance greater than that of PTB7, which is set as reference. Our calculations show a possible approach to the rational design of donor materials when substituents are inserted systematically in a generic oligomer.

Delicately Controlled Polymer Orientation for High-Performance Non-Fullerene Solar Cells with Halogen-Free Solvent Processing

Molecular orientation in polymer solar cells (PSCs) is a critical subject of investigation that promotes the quality of bulk heterojunction morphology and power conversion efficiency (PCE). Herein, the intrinsic polymer orientation transition can be found upon delicate control over the branching point position of the irregular alkoxy side chain in difluoroquinoxaline-thiophene-based conjugated polymers. Three polymers with branching points at the third, fourth, and fifth positions away from the backbone were synthesized and abbreviated as PHT3, PHT4, and PHT5, respectively. Temperature-dependent absorption behavior manifests the polymer aggregation ability in the order of PHT3 < PHT4 < PHT5. Surprisingly, the polymer orientation transition from typical face-on to edge-on emerged between PHT4 and PHT5, as evidenced by X-ray-scattering analysis. The enhanced face-on crystallinity of PHT4 endowed the o-xylene-processed PHT4:IT-4Cl-based devices with the highest PCE of 13.40%. For PHT5 with stronger aggregation, the related o-xylene-processed PSCs still showed a good PCE of 12.66%. Our results demonstrate that a delicate polymer orientation transition could be realized through a precisely controlled strategy of the side chain, yielding green-solvent-processed high-performance PSCs.

Contrasting Effect of Side-Chain Placement on Photovoltaic Performance of Binary and Ternary Blend Organic Solar Cells in Benzodithiophene-Thiazolothiazole Polymers

π-Conjugated polymers are important materials for organic photovoltaics. While search for new backbone systems is central to the development of π-conjugated polymers, side-chain engineering is also imperative. Here, two benzodithiophene-thiazolothiazole copolymers, PSTz1 and POTz1, were synthesized, for which the side-chain placement was different. Due to less steric hindrance between the side chains, PSTz1 had a more coplanar backbone than POTz1. This led to significant differences in trend of the performance for the binary and ternary blend cells that used a fullerene (PC₇₁ BM) and/or non-fullerene (ITIC) as the acceptor materials. Whereas PSTz1 showed higher photovoltaic performance in the PC₇₁ BM-based cell, POTz1 showed higher performance in the ITIC-based cell. Furthermore, in the ternary blend cell, whereas increase in the PC₇₁ BM content improved the photovoltaic performance for the PSTz1 system, it was detrimental to the performance for the POTz1 system. These results could be a good guideline for maximizing the performance of organic photovoltaics.

Effects of Alkyl Side Chains of Small Molecule Donors on Morphology and the Photovoltaic Property of All-Small-Molecule Solar Cells

Unraveling the relationship between nanoscale morphology of active layers and chemical structures of organic semiconductor photovoltaic materials is crucially important for further advancing the development of all-small-molecule organic solar cells (SM-OSCs). Here, in order to delve into the effect of flexible side chains of small molecule donors on the photovoltaic properties of SM-OSCs, we synthesized two new small molecule donors substituted by different flexible alkyl chains (iso-octyl chains for SM1-EH and n-octyl chains for SM1-Oct). As a result, the two small molecules present different absorption properties, energy levels, and stacking characteristics. When blending with Y6 as an acceptor, the SM1-Oct-based SM-OSC demonstrated a higher PCE value of 11.73%, while the SM1-EH-based device presents a relatively poorer PCE value of 8.42%. In addition, the morphology analysis demonstrated that, compared with the SM1-EH:Y6 blend, the SM1-Oct:Y6 blend film displayed better molecular stacking properties with stronger multilevel diffraction and preferable phase separation, resulting in the higher hole mobility, more efficient charge separation efficiency, and better device performance. These results underline that reasonably adjusting the flexible alkyl chains of small molecule donors can be an effective approach to further advance the development of the SM-OSCs field.

Recent Advances of Furan and Its Derivatives Based Semiconductor Materials for Organic Photovoltaics

The state-of-the-art bulk-heterojunction (BHJ)-type organic solar cells (OSCs) have exhibited power conversion efficiencies (PCEs) of exceeding 18%. Thereinto, thiophene and its fused-ring derivatives play significant roles in facilitating the development of OSCs due to their excellent semiconducting natures. Furan as thiophene analogue, is a ubiquitous motif in naturally occurring organic compounds. Driven by the advantages of furan, such as less steric hindrance, good solubility, excellent stacking, strong rigidity and fluorescence, biomass derived fractions, more and more research groups focus on the furan-based materials for using in OSCs in the past decade. To systematically understand the developments of furan-based photovoltaic materials, the relationships between the molecular structures, optoelectronic properties, and photovoltaic performances for the furan-based semiconductor materials including single furan, benzofuran, benzodifuran (BDF) (containing thienobenzofuran (TBF)), naphthodifurans (NDF), and polycyclic furan are summarized. Finally, the empirical regularities and perspectives of the development of this kind of new organic semiconductor materials are extracted.

Keep glowing and going: recent progress in diketopyrrolopyrrole synthesis towards organic optoelectronic materials

Recent progress in the syntheses of DPP derivatives is summarized as well as the structure–property relationships of the derivatives, including the syntheses of DPP cores, N-functionalization reactions, and π-extensions on and along the DPP cores.

Influence of Alkyl Substitution Position on Wide-Bandgap Polymers in High-Efficiency Nonfullerene Polymer Solar Cells

Two wide-bandgap (WBG) conjugated polymers (PBPD-p and PBPD-m) based on phenyl-substituted benzodithiophene (BDT) with the different substitution position of the alkyl side chain and benzodithiophene-4,8-dione (BDD) units are designed and synthesized to investigate the influence of alkyl substitution position on the photovoltaic performance of polymers in polymer solar cells (PSCs). The thermogravimetric analysis, absorption spectroscopy, molecular energy level, X-ray diffraction, charge transport and photovoltaic performance of the polymers are systematically studied. Compared with PBPD-p, PBPD-m exhibits a slight blue-shift but a deeper highest occupied molecular orbital (HOMO) energy level, a tighter alkyl chain packing and a higher hole mobility. The PBPD-m-based PSCs blended with acceptor IT-4F shows a higher power conversion efficiency (PCE) of 11.95% with a high open-circuit voltage (V_oc ) of 0.88 V, a short-circuit current density (J_sc ) of 19.76 mA cm^-2 and a fill factor (FF) of 68.7% when compared with the PCE of 6.97% with a V_oc of 0.81 V, a J_sc of 15.97 mA cm^-2 and an FF of 53.9% for PBPD-p. These results suggest that it is a feasible and effective strategy to optimize photovoltaic properties of WBG polymers by changing the substitution position of alkyl side chain in PSCs.

Comparing Benzodithiophene Unit with Alkylthionaphthyl and Alkylthiobiphenyl Side-Chains in Constructing High-Performance Nonfullerene Solar Cells

Using single-bonded and fused aromatic rings are two methods for extending the π-conjugation in the vertical direction of benzo [1,2-b:4,5-b'] dithiophene (BDT) unit. To investigate which method is more efficient in nonfullerene systems, two novel polymers based on alkylthionaphthyl and alkylthiobiphenyl substituted BDT named PBDTNS-FTAZ and PBDTBPS-FTAZ are designed and synthesized. Two polymers only exhibit small differences in structure, but huge differences in photovoltaic properties. They are studied by blended with 3,9-bis(2-methylene-(3-(1,1-dicyanomethylene)indanone)-5,5,11,11-tetrakis(4-hexylphenyl)dithieno [2,3-d':2,3'-d']-s-indaceno [1,2-b:5,6-b'] dithiophene (ITIC). The device based on PBDTNS-FTAZ:ITIC showed the best power conversion efficiency (PCE) of 9.63% with the Voc of 0.87 V, a Jsc of 18.06 mA/cm2 and a fill factor of 61.21%, while the PBDTBPS-FTAZ:ITIC only exhibit a maximum PCE of 7.79% with a Voc of 0.86 V, a Jsc of 16.24 mA/cm2 and a relatively low fill factor of 55.92%. Therefore, extending π-conjugation with alkylthionaphthyl is more effective against constructing nonfullerene solar cells.

Tunable Control of the Hydrophilicity and Wettability of Conjugated Polymers by a Postpolymerization Modification Approach

A facile method to prepare hydrophilic polymers by a postpolymerization nucleophillic aromatic substitution reaction of fluoride on an emissive conjugated polymer (CP) backbone is reported. Quantitative functionalization by a series of monofunctionalized ethylene glycol oligomers, from dimer to hexamer, as well as with high molecular weight polyethylene glycol is demonstrated. The length of the ethylene glycol sidechains is shown to have a direct impact on the surface wettability of the polymer, as well as its solubility in polar solvents. However, the energetics and band gap of the CPs remain essentially constant. This method therefore allows an easy way to modulate the wettability and solubility of CP materials for a diverse series of applications.

Highly Efficient All-Small-Molecule Organic Solar Cells with Appropriate Active Layer Morphology by Side Chain Engineering of Donor Molecules and Thermal Annealing

It is very important to fine-tune the nanoscale morphology of donor:acceptor blend active layers for improving the photovoltaic performance of all-small-molecule organic solar cells (SM-OSCs). In this work, two new small molecule donor materials are synthesized with different substituents on their thiophene conjugated side chains, including SM1-S with alkylthio and SM1-F with fluorine and alkyl substituents, and the previously reported donor molecule SM1 with an alkyl substituent, for investigating the effect of different conjugated side chains on the molecular aggregation and the photophysical, and photovoltaic properties of the donor molecules. As a result, an SM1-F-based SM-OSC with Y6 as the acceptor, and with thermal annealing (TA) at 120 °C for 10 min, demonstrates the highest power conversion efficiency value of 14.07%, which is one of the best values for SM-OSCs reported so far. Besides, these results also reveal that different side chains of the small molecules can distinctly influence the crystallinity characteristics and aggregation features, and TA treatment can effectively fine-tune the phase separation to form suitable donor-acceptor interpenetrating networks, which is beneficial for exciton dissociation and charge transportation, leading to highly efficient photovoltaic performance.

All-Small-Molecule Organic Solar Cells Based on a Fluorinated Small Molecule Donor With High Open-Circuit Voltage of 1.07 V

A new small molecule donor with an acceptor-donor-acceptor (A-D-A) structure, namely DRTB-FT, has been designed and synthesized for all-small-molecule organic solar cells (ASM-OSCs). By introducing fluorine atoms on the thienyl substituent of the central benzodithiophene unit, DRTB-FT shows a low-lying highest occupied molecular orbital (HOMO) energy level of -5.64 eV. Blending with an A-D-A type acceptor F-2Cl, DRTB-FT based ASM-OSCs gave a power conversion efficiency (PCE) of 7.66% with a high open-circuit voltage (V oc) of 1.070 V and a low energy loss of 0.47 eV. The results indicate that high V oc of ASM-OSC devices can be obtained through careful donor molecular optimization.

Controlling Molecule Aggregation and Electronic Spatial Coherence in the H-Aggregate and J-Aggregate Regime at Room Temperature

Controlling molecule aggregation in polymer films is one of the key factors in understanding the links between properties and structures in organic semiconductors. Here, we used poly(3-hexylthiophene-2,5-diyl) (P3HT) as the model system. By doping the insulating polar additive poly (ethylene oxide) (PEO) into P3HT film and controlling the processing methods, we achieved the side-to-side H-aggregate and head-to-tail J-aggregate of P3HT molecules with different extents at room temperature. We have demonstrated that the solvent solidification rate plays an important role in the controlling of molecule aggregation, which finally influenced the solid-state phase separation in the film. Furthermore, based on a series of spectroscopy investigations, we quantified the electronic spatial coherence in different aggregations combined with the modified Franck-Condon model. Subsequently, we established the relationship between the processing method, the molecule aggregation, and the electronic spatial coherence.

Pronounced Dependence of All-Polymer Solar Cells Photovoltaic Performance on the Alkyl Substituent Patterns in Large Bandgap Polymer Donors

For all-polymer solar cells which are composed of polymer donors and polymer acceptors, the effect of alkyl side chains on photovoltaic performance is a matter of some debate, and this effect remains difficult to forecast. In this concise contribution, we demonstrate that three alkyls namely branched alkyl 2-butyloctyl (2BO), long linear alkyl n-dodecyl (C12), and double-short linear alkyl n-hexyls (DC6) incorporated into the side chains of large bandgap polymer donor PBDT-TTz can induce considerable, of significance, and different electronic, optical, and morphological parameters. Systematic studies shed light on the critical role of the double-short linear alkyl n-hexyls (DC6) in (i) producing large ionization potential value, (ii) increasing propensity of the polymer to order along the π-stacking direction, (iii) generating polymer crystallites with more preferential "face-on" orientation, consequently, (iv) improvement of carriers transportation, (v) suppression of charge recombination, (vi) reduction of energy loss in all-polymer devices. In parallel, we unearth that the PBDT-TTz with double-short linear alkyl n-hexyls (DC6) represents the highest efficiency of 8.3 %, whereas, the other two PBDT-TTz analogues (2BO, C12) yield efficiencies of less than 3 % in optimized all-polymer solar cells. Though branched or long linear alkyl side chains (2BO, C12) have been applied to provide the solution processability of conjugated polymers, motifs bearing multiple short linear alkyl substituents (DC6) are proved critical to the development of high performing polymers.

Substantial Improvement of the Dielectric Strength of Cellulose-Liquid Composites: Effects of Traps at the Nanoscale Interface

The dielectric strength of cellulose-liquid composites is always about several times higher than that of the cellulose paper and insulating liquids. However, this experimental phenomenon has not yet been demonstrated theoretically. Herein, the spectra characterization, molecular simulation, and wave function analysis method provide a new insight that the role of nanoscale interfacial adsorption of cellulose-liquid is exclusive for composites affecting the charge separation and producing the deep-level traps to seriously hinder electromigration under an electric field, which is responsible for the difference in dielectric strength. Meanwhile, the π conjugation and σ-π hyperconjugation effects enhance the electrical stability of aromatic hydrocarbon insulating liquids. In conclusion, interfacial trap theory can be used to explain the correlation of dielectric strength between cellulose-liquid composites and cellulose paper or dielectric liquids. It can be expected that materials with high dielectric strength can be manufactured according to the fundamental study of interfacial trap theory.

High Efficiency Polymer Solar Cells with Efficient Hole Transfer at Zero Highest Occupied Molecular Orbital Offset between Methylated Polymer Donor and Brominated Acceptor

Achieving efficient charge transfer at small frontier molecular orbital offsets between donor and acceptor is crucial for high performance polymer solar cells (PSCs). Here we synthesize a new wide band gap polymer donor, PTQ11, and a new low band gap acceptor, TPT10, and report a high power conversion efficiency (PCE) PSC (PCE = 16.32%) based on PTQ11-TPT10 with zero HOMO (the highest occupied molecular orbital) offset (ΔE_HOMO(D-A)). TPT10 is a derivative of Y6 with monobromine instead of bifluorine substitution, and possesses upshifted lowest unoccupied molecular orbital energy level (E_LUMO) of -3.99 eV and E_HOMO of -5.52 eV than Y6. PTQ11 is a derivative of low cost polymer donor PTQ10 with methyl substituent on its quinoxaline unit and shows upshifted E_HOMO of -5.52 eV, stronger molecular crystallization, and better hole transport capability in comparison with PTQ10. The PSC based on PTQ11-TPT10 shows highly efficient exciton dissociation and hole transfer, so that it demonstrates a high PCE of 16.32% with a higher V_oc of 0.88 V, a large J_sc of 24.79 mA cm^-2, and a high FF of 74.8%, despite the zero ΔE_HOMO(D-A) value between donor PTQ11 and acceptor TPT10. The PCE of 16.32% is one of the highest efficiencies in the PSCs. The results prove the feasibility of efficient hole transfer and high efficiency for the PSCs with zero ΔE_HOMO(D-A), which is highly valuable for understanding the charge transfer process and achieving high PCE of PSCs.

BODIPY bearing alkylthienyl side chains: a new building block to design conjugated polymers with near infrared absorption for organic photovoltaics

A new benzene-fused BODIPY unit for designing polymer donors with near-infrared absorption for organic photovoltaics.

Oligo(ethylene glycol) as side chains of conjugated polymers for optoelectronic applications

Except hydrophobic alkyl side chains, hydrophilic oligo(ethylene glycol) (OEG) has also been used as side chains of conjugated polymers and endow the resulting polymers with interesting properties and excellent opto-electronic device performance.

Regulation of Molecular Packing and Blend Morphology by Finely Tuning Molecular Conformation for High-Performance Nonfullerene Polymer Solar Cells

The asymmetric thienobenzodithiophene (TBD) structure is first systematically compared with the benzo[1,2-b:4,5-b']dithiophene (BDT) and dithieno[2,3-d:2',3'-d']benzo[1,2-b:4,5-b']dithiophene (DTBDT) units in donor-acceptor (D-A) copolymers and applied as the central core in small molecule acceptors (SMAs). Specific polymers including PBDT-BZ, PTBD-BZ, and PDTBDT-BZ with different macromolecular conformations are synthesized and then matched with four elaborately designed acceptor-donor-acceptor (A-D-A) SMAs with structures comparable to their donor counterparts. The resulting polymer solar cell performance trends are dramatically different from each other and highly material-dependent, and the active layer morphology is largely governed by polymer conformation. Because of its more linear backbone, the PTBD-BZ film has higher crystallinity and more ordered and denser π-π stacking than those of the PBDT-BZ and PDTBDT-BZ films. Thus, PTBD-BZ shows excellent compatibility with and strong independence on the SMAs with varied structures, and PTBD-BZ-based cells deliver high power conversion efficiency (PCE) of 10-12.5%, whereas low PCE is obtained by cells based on PDTBDT-BZ because of its zigzag conformation. Overall, this study reveals control of molecular conformation as a useful approach to modulate the photovoltaic properties of conjugated polymers.

Side chain effect on conjugated polymer/fullerene interfaces in organic solar cells: a DFT study

Considerable experimental research has been conducted on the influence of polymer alkyl side chains on the performance of bulk heterojunction organic solar cells. However, greater insight into the role of alkyl side chains in the polymer/fullerene interfacial regions is still needed. Using the dispersion-corrected density functional theory, we investigate the effect of alkyl side chains on the binding energies and electronic structures of various molecular pairings of fullerenes and monomers of organic copolymers (e.g. a pair of PC₇₁BM and a monomer of copolymer PTB7 based on the thieno[3,4-b]thiophene/benzodithiophene repeat unit, PCBM and a copolymer PCDTBT based on 2,7-carbazole/dithienyl-2,1,3-benzothiazole and PC₇₁BM and a copolymer PffBT4T-2OD based on difluorobenzothiadiazole/quaterthiophene). We find that the trends of the magnitudes of the binding energies vary with the lengths, types (branched or linear), and branching positions of alkyl side chains. Whenever possible, these results are compared with the efficiency trends of the corresponding organic solar cells. With the help of this comparison optimal side chain arrangements in bulk heterogeneous organic solar cells are identified. It is expected that these insights will aid in the production of more efficient organic photovoltaics.

Random Polymer Donor for High-Performance Polymer Solar Cells with Efficiency over 14

Constructing random copolymers has been regarded as an easy and effective approach to design polymer donors for state-of-the-art polymer solar cells (PSCs). In this work, we develop a naphtho[2,3-c]thiophene-4,9-dione-based copolymer PBN-Cl as a donor material for PSCs, and a moderate power conversion efficiency (PCE) of 11.21% is achieved with a relatively low fill factor (FF) of 0.615. We then incorporate a similar acceptor unit benzo[1,2-c:4,5-c']dithiophene-4,8-dione (BDD) into the polymeric backbone of PBN-Cl to tune its photovoltaic performance, and a significantly higher PCE of 14.05% is achieved from the random polymer PBN-Cl-B80 containing 80% BDD unit. The enhanced PCE of the PBN-Cl-B80-based device mainly relies on the higher FF value, resulting from the improved charge mobility properties, reduced bimolecular and trap-assisted recombination, and more appropriate phase separation. The results demonstrate a feasible strategy to tune the photovoltaic performance of polymer donors by constructing a random polymer with a compatible component.

Hydrogen plasma-treated MoSe2 nanosheets enhance the efficiency and stability of organic photovoltaics

In this paper we report the effect on the power conversion efficiency (PCE) and stability of photovoltaic devices after incorporating hydrogenated two-dimensional (2D) MoSe₂ nanosheets into the active layer of bulk heterojunction (BHJ) organic photovoltaics (OPV). The surface properties of 2D MoSe₂ nanosheets largely affect their dispersion in the active layer blend and, thus, influence the carrier mobility, PCE, and stability of corresponding devices. We treated MoSe₂ nanosheets with hydrogen plasma and investigated their influence on the polymer packing and fullerene domain size of the active layer. For the optimized devices incorporating 37.5 wt% of untreated MoSe₂, we obtained a champion PCE of 9.82%, compared with the champion reference PCE of approximately 9%. After incorporating the hydrogen plasma-treated MoSe₂ nanosheets, we achieved a champion PCE of 10.44%-a relative increase of 16% over that of the reference device prepared without MoSe₂ nanosheets. This PCE is the one of the highest ever reported for OPVs incorporating 2D materials. We attribute this large enhancement to the enhanced exciton generation and dissociation at the MoSe₂-fullerene interface and, consequently, the balanced charge carrier mobility. The device incorporating the MoSe₂ nanosheets maintained 70% of its initial PCE after heat-treatment at 100 °C for 1 h; in contrast, the PCE of the reference device decreased to 60% of its initial value-a relative increase in stability of 17% after incorporating these nanosheets. We also incorporated MoSe₂ nanosheets (both with and without treatment) into a polymer donor (PBDTTBO)/small molecule (IT-4F) acceptor system. The champion PCEs reached 7.85 and 8.13% for the devices incorporating the MoSe₂ nanosheets with and without plasma treatment, respectively-relative increases of 8 and 12%, respectively, over that of the reference. These results should encourage a push toward the implementation of transition metal dichalcogenides to enhance the performances of BHJ OPVs.

Photovoltaic Blend Microstructure for High Efficiency Post-Fullerene Solar Cells. To Tilt or Not To Tilt?

Achieving efficient polymer solar cells (PSCs) requires a structurally optimal donor-acceptor heterojunction morphology. Here we report the combined experimental and theoretical characterization of a benzodithiophene-benzothiadiazole donor polymer series (PBTZF4-R; R = alkyl substituent) blended with the non-fullerene acceptor ITIC-Th and analyze the effects of substituent dimensions on blend morphology, charge transport, carrier dynamics, and PSC metrics. Varying substituent dimensions has a pronounced effect on the blend morphology with a direct link between domain purity, to some extent domain dimensions, and charge generation and collection. The polymer with the smallest alkyl substituent yields the highest PSC power conversion efficiency (PCE, 11%), reflecting relatively small, high-purity domains and possibly benefiting from "matched" donor polymer-small molecule acceptor orientations. The distinctive morphologies arising from the substituents are investigated using molecular dynamics (MD) simulations which reveal that substituent dimensions dictate a well-defined set of polymer conformations, in turn driving chain aggregation and, ultimately, the various film morphologies and mixing with acceptor small molecules. A straightforward energetic parameter explains the experimental polymer domain morphological trends, hence PCE, and suggests strategies for substituent selection to optimize PSC materials morphologies.

Effect of Flank Rotation on the Photovoltaic Properties of Dithieno[2,3-d:2',3'-d']benzo[1,2-b:4,5-b']dithiophene-Based Narrow Band Gap Copolymers

Side chain engineering has been an effective approach to modulate the solution processability, optoelectronic properties and miscibility of conjugated polymers (CPs) for organic/polymeric photovoltaic cells (PVCs). As compared with the most commonly used method of introducing alkyl chains, the employment of alkyl-substituted aryl flanks would provide two-dimensional (2-D) CPs having solution processability alongside additional merits like deepened highest occupied molecular orbital (HOMO) energy levels, increased absorption coefficient and charger transporting, etc. In this paper, the triple C≡C bond was used as conjugated linker to decrease the steric hindrance between the flanks of 4,5-didecylthien-2-yl (T) and dithieno[2,3-d:2',3'-d']benzo[1,2-b:4,5-b']dithiophene (DTBDT) core. In addition, an alternating CP derived from 4,5-didecylthien-2-yl-ethynyl (TE) flanked DTBDT, and 4,9-bis(4-octylthien-2-yl) naphtho[1,2-c:5,6-c']bis[1,2,5]thiadiazole (DTNT), named as PDTBDT-TE-DTNT, was synthesized and characterized. As compared with the controlled PDTBDT-T-DTNT, which was derived from 4,5-didecylthien-2-yl flanked DTBDT and DTNT, the results for exciton dissociation probability, density functional theory (DFT), time-resolved photoluminescence (PL) measurements, etc., revealed that the lower steric hindrance between TE and DTBDT might lead to the easier rotation of the TE flanks, thus contributing to the decrease of the exciton lifetime and dissociation probability, finally suppressing the short-circuit current density (JSC), etc., of the photovoltaic devices from PDTBDT-TE-DTNT.

Defining side chain successions in anthracene-based poly(arylene ethynylene)-alt-poly(phenylene vinylene)s: probing structure–property relationships

A detailed spectroscopic study of nine conjugated polymers with various octyloxy/2-ethylhexyloxy side chain sequences prepared using optimized regio-selective synthetic pathways.

Revealing working mechanisms of PFN as a cathode interlayer in conventional and inverted polymer solar cells

The working mechanisms of PFN as a cathode interlayer in conventional and inverted polymer solar cells have been revealed mainly using ultraviolet photoemission spectroscopy.