Towards a bright future: polymer solar cells with power conversion efficiencies over 10%

Naphthalene diimide-based random terpolymer acceptors for constructing all-polymer solar cells with enhanced fill factors

All-polymer solar cells (all-PSCs) with mechanical and thermal stability have potential for applications in flexible devices. Polymer acceptors based on naphthalene diimide (NDI) have been widely studied because of their strong electron affinity, high electron mobility, and high mechanical reliability. However, controlling the film morphology of the polymer–polymer blends of NDI-based all-PSCs is difficult. Consequently, all-PSCs based on NDI building blocks exhibit a low fill factor (FF) and a lower power-conversion efficiency (PCE) than state-of-the-art polymer solar cells. In this work, we added a small amount of dicyanodistyrylbenzene (DCB) unit to the NDI-based polymer acceptor N2200 through random copolymerization and synthesized a series of NDI-based terpolymer acceptors PNDIx, where x is the molar concentration of DCB units relative to NDI units. PNDI5 and PNDI10, corresponding to 5% and 10% molar concentrations of DCB, respectively, showed lower crystallization and good miscibility with PBDB-T, a widely used electron-donating copolymer, than the terpolymer based on DCB-free N2200. Moreover, compared to the PBDB-T:N2200 device, the PNDI5-based device exhibited a much higher PCE (8.01%), and an enhanced FF of 0.75 in all-PSCs. These results indicate that ternary random copolymerization is a convenient and effective strategy for optimizing the film morphology of NDI-based polymers, and that the resulting terpolymer acceptor is a promising n-type acceptor for constructing high-performance all-PSCs.

We developed two terpolymer acceptors based on N2200 through random copolymerization for all polymer solar cells with enhanced fill factors and photovoltaic performance.

Performance Analysis and Optimization of a PBDB-T:ITIC Based Organic Solar Cell Using Graphene Oxide as the Hole Transport Layer

The hole transport layer (HTL) in organic solar cells (OSCs) plays an imperative role in boosting the cell’s performance. PEDOT: PSS is a conventional HTL used in OSCs owing to its high design cost and instability issues. It can be replaced with graphene oxide to increase the cell performance by overcoming instability issues. Graphene oxide (GO) has gained popularity in recent years for its practical use in solar energy due to its remarkable mechanical, electrical, thermal, and optical properties. This work uses SCAPS-1D to examine the results of graphene oxide (GO)-based organic solar cells by giving a comparison between the performance of absorber layers and a GO-based HTL to see which absorber material interacts more strongly with GO. The absorber layer PBDB-T:ITIC paired with GO as HTL outperforms the other absorber layers due to its better optical and electrical characteristics. Numerical simulations are performed within the SCAPS software at various absorber layer thicknesses, defect densities, and doping values to assess the influence on device performance and efficiency. After cell optimization, the best efficiency of an improved OSC is found to be 17.36%, and the outcomes of the simulated OSC are referenced to the results of the experimentally implemented OSC. These results provide a possible future direction for developing GO-based OSCs with higher efficiency.

The impact of thermal treatment on the performance of benzo[1,2-b:4,5-b']difuran-based organic solar cells

The new low bandgap benzo[1,2-b:4,5-b']difuran (BDF)-based organic small molecule, namely B1, was synthesized by Stille coupling polymerization reactions. B1 was found to be soluble in common organic solvents such as chloroform, toluene and chlorobenzene with excellent film forming properties. The structure of B1 was verified by 1H NMR, GC-MS and elemental analysis. The B1 films exhibit broad absorption bands from 300 to 750 nm. The hole mobility of B1 : PC61BM (1 : 1, w/w) blend film reached up to 7.7 × 10-2 cm V-1 s-1 after thermal annealing by the space-charge-limited current method. BHJ organic solar cells (OSCs) were fabricated with a device structure of ITO/PEDOT : PSS/B1 : C61BM/LiF/Al. When the active layer was thermally annealed at 120 °C, B1 showed the best photovoltaic performance, with a PCE up to 5.0%. We also studied the connection between the morphologies of the active layers and the photovoltaic performance by AFM, PL, etc. Our observation will guide future design for even better small molecules for highly efficient OSCs.

Cationic Polyelectrolytes with Alkylsulfonate Counterions as a Cathode Interface Layer for High-Performance Polymer Solar Cells

Three cationic polyelectrolytes polyethyleneimine ethoxylate (PEIE)-1,4-butanediol dimethylsulfonate (MSB), PEIE-1,4-butanediol diethylsulfonate (ESB), and PEIE-1,4-butanediol dibenzylsulfonate (BSB), containing methylsulfonate, ethylsulfonate, and benzylsulfonate, respectively, were prepared for cathode interface layers (CILs) via a one-step reaction with 1,4-butanediol dialkylsulfonate and PEIE as the reactants. The results indicate that PEIE-MSB and PEIE-ESB with smaller counterions possess more efficient electron extraction, higher electron mobilities, and better photovoltaic performance than PEIE-BSB with larger counterions. The PTB7-Th:PC₇₁BM-based single junction bulk heterojunction polymer solar cells (PSCs) with PEIE-ESB as the CIL showed power conversion efficiencies (PCEs) of 10.44 and 9.23% under the thickness conditions of 8 and 30 nm, respectively. The PM6:Y6-based PSCs displayed a high PCE of 15.69%. The study provides not only new high-performance CILs but also a new strategy to construct light-soaking-free PSCs via tuning alkylsulfonate counterions.

Hydrophilic Conjugated Materials for Photocatalytic Hydrogen Evolution

Photocatalytic hydrogen evolution is viewed as a promising green strategy to utilize the inexhaustible solar energy and provide clean hydrogen fuels with zero-emission characteristic. The nature of semiconductor-based photocatalysts is the key point to achieve efficient photocatalytic hydrogen evolution. Conjugated materials have been recently emerging as a novel class of photocatalysts for hydrogen evolution and photocatalytic reactions due to their electronic properties can be well controlled via tailor-made chemical structures. Hydrophilic conjugated materials, a subgroup of conjugated materials, possess multiple advantages for photocatalytic applications, thus spurring remarkable progress on both material realm and photocatalytic applications. This minireview aims to provide a brief review of the recent developments of hydrophilic conjugated polymers/small molecules for photocatalytic applications, and special concern on the rational molecular design and their impact on photocatalytic performance will be reviewed. Perspectives on the hydrophilic conjugated materials and challenges to their applications in the photocatalytic field are also presented.

Influence of the –CN substitution position on the performance of dicyanodistyrylbenzene-based polymer solar cells

We developed four novel copolymers based on DCB units with differently positioned –CN groups and investigated their effects on the film morphology and performance of non-fullerene polymer solar cells.

Ternary Polymer Solar Cells Facilitating Improved Efficiency and Stability

The use of a ternary active layer offers a promising approach to enhance the power conversion efficiency (PCE) of polymer solar cells (PSCs) via simply incorporating a third component. Here, a ternary PSC with improved efficiency and stability facilitated by a new small molecule IBC-F is demonstrated. Even though the PBDB-T:IBC-F-based device gives an extremely low PCE of only 0.21%, a remarkable PCE of 15.06% can be realized in the ternary device based on PBDB-T:IE4F-S:IBC-F with 20% IBC-F, which is ≈10% greater than that (PCE = 13.70%) of the control binary device based on PBDB-T:IE4F-S. The improvement in the device performance of the ternary PSC is mainly attributed to the enhancement of fill factor, which is due to the improved charge dissociation and extraction, suppressed bimolecular and trap-assisted recombination, longer charge-carrier lifetime, and enhanced intermolecular interactions for preferential face-on orientation. Additionally, the ternary device with 20% IBC-F shows better thermal and photoinduced stability over the control binary device. This work provides a new angle to develop the third components for building ternary PSCs with enhanced photovoltaic performance and stability for practical applications.

Conjugated Donor-Acceptor Terpolymers Toward High-Efficiency Polymer Solar Cells

The development of conjugated alternating donor-acceptor (D-A) copolymers with various electron-rich and electron-deficient units in polymer backbones has boosted the power conversion efficiency (PCE) over 17% for polymer solar cells (PSCs) over the past two decades. However, further enhancements in PCEs for PSCs are still imperative to compensate their imperfect stability for fulfilling practical applications. Meanwhile development of these alternating D-A copolymers is highly demanding in creative design and syntheses of novel D and/or A monomers. In this regard, when being possible to adopt an existing monomer unit as a third component from its libraries, either a D' unit or an A' moiety, to the parent D-A type polymer backbones to afford conjugated D-A terpolymers, it will give a facile and cost-effective method to improve their light absorption and tune energy levels and also interchain packing synergistically. Moreover, the rationally controlled stoichiometry for these components in such terpolymers also provides access for further fine-tuning these factors, thus resulting in high-performance PSCs. Herein, based on their unique features, the recent progress of conjugated D-A terpolymers for efficient PSCs is reviewed and it is discussed how these factors influence their photovoltaic performance, for providing useful guidelines to design new terpolymers toward high-efficiency PSCs.

Design, Synthesis and Computational Study of Fluorinated Quinoxaline-Oligothiophene-based Conjugated Polymers with Broad Spectral Coverage

Donor-acceptor (D-A) copolymers typically show two absorption peaks in the visible region, flanking a valley region of limited absorptivity. One strategy for more panchromatic light harvesting is to incorporate side-groups orthogonal to the polymer backbone, which enable 2D π conjugation and can give rise to additional absorption peaks. Here we design and synthesize two D-A polymers which both carry a fluorinated quinoxaline acceptor unit, but while P1 includes a benzodithiophene donor moiety with thiophene side-groups (2D-BDT), the P2 polymer lacks 2D conjugation in its simpler pentathiophene donor segment. The P1 polymer consequently shows an atypical absorption profile with more panchromatic absorption with no apparent valley in the spectrum. In order to understand the structure-electronic relations, the optical and electrochemical properties were predicted using a previously developed computational approach. The predicted optical properties show very good agreement with the experimental results. Solar cells made from P1 show a short-circuit current more than twice as large as P2, attributed to its enhanced spectral coverage. However, poor fill factors limit the preliminary power conversion efficiencies to 3.3 % for P1 and 1.0 % for P2 as blended with PCBM[70] in a 1 : 1.5 (w/w) ratio.

High-Performance Ternary Nonfullerene Polymer Solar Cells with Both Improved Photon Harvesting and Device Stability

Efficiency and stability of polymer solar cells (PSCs) are the two most significant decisive factors for the purpose of actual applications. Here, highly efficient and stable ternary PSCs were fabricated by incorporating two well-compatible polymer donors (poly[4,8-bis(5-(2-ethylhexyl)thiophen-2-yl)benzo[1,2- b;4,5- b0]dithiophene-2,6-diyl- alt-(4-(2-ethylhexyl)-3-fluorothieno[3,4- b]thiophene-)-2-carboxylate-2-6-diyl] and poly[[9-(1-octylnonyl)-9 H-carbazole-2,7-diyl]-2,5-thiophenediyl-2,1,3-benzothiadiazole-4,7-diyl-2,5-thiophenediyl]) with one narrow band gap nonfullerene acceptor (3,9-bis(2-methylene-(3-(1,1-dicyanomethylene)-indanone)-5,5,11,11-tetrakis(4-hexylphenyl)-dithieno[2,3- d:2',3'- d']- s-indaceno[1,2- b:5,6- b']dithiophene)). It is found that Förster resonance energy transfer acts as an efficient pathway to further strengthen photon harvesting in this ternary system, which results in a significant improvement in current density ( J_SC) without sacrificing the strong absorption of binary blends in the near-infrared region. Meanwhile, both of the inverted and conventional ternary PSCs exhibit better stability compared with the related binary PSCs in air condition because of the interlocked morphology in ternary films. The optimized ternary PSCs exhibit an outstanding power conversion efficiency (PCE) of 9.53% resulting from the synchronous improvements in J_SC and fill factor. Moreover, this ternary strategy can be further confirmed by the use of an ultranarrow-band gap nonfullerene acceptor IEICO-4F, and the champion PCE of ternary PSCs reaches to 12.15%.

Enhanced Performance of Inverted Non-Fullerene Organic Solar Cells by Using Metal Oxide Electron- and Hole-Selective Layers with Process Temperature ≤150 °C

In this work, an efficient inverted organic solar cell (OSC) based on the non-fullerene PBDB-T:IT-M blend system is demonstrated by using an aqueous solution processed ZnO electron-selective layer with the whole process temperature ≤150 °C and a thermally evaporated MoO₃ hole-selective layer The ZnO selective layer is deposited by aqueous solution and prepared in a low-temperature process, so that it can be compatible with the roll-to-roll process. The proposed device achieves an enhanced power conversion efficiency (PCE) of 9.33% compared with the device based on the high-temperature sol-gel-processed ZnO selective layer, which achieves a PCE of 8.62%. The inverted device also shows good stability, keeping more than 82% of its initial PCE after being stored under ambient air conditions and a humidity of around 40% without any encapsulation for 240 h. The results show the potential for the fabrication of efficient non-fullerene OSCs with low-temperature metal oxide selective layers.

PANI Branches onto Donor-Acceptor Copolymers: Synthesis, Characterization and Electroluminescent Properties of New 2D-Materials

A new series of two-dimensional statistical conjugated polymers based on aniline and 9,9-dihexylfluorene as donor units and benzo- or naphtho-quinoxaline/thiadiazole derivatives as acceptor moieties, possessing PANI segments as side chains, were designed and synthesized. To investigate the effects of the perpendicular PANI branches on the properties of the main chain, the optical, electrochemical, morphological and electroluminescence properties were studied. The 2D materials tend to possess lower molecular weights and to absorb and to emit light red-shifted compared to the trunk 1D-polymers, in the yellow-red region of the visible spectrum. The 1D- and 2D-conjugated polymers present optical band gaps ranging from 2.15⁻2.55 eV, HOMO energy levels between -5.37 and -5.60 eV and LUMO energy levels between -3.02 and -3.29 eV. OLED devices based on these copolymers were fabricated. Although the performances were far from optimal due to the high turn-on voltages for which electroluminescence phenomena occur, a maximum luminescence of 55,100 cd/m² together with a current density of 65 mA/cm² at 18.5 V were recorded for a 2D-copolymer, PAFC6TBQ-PANI.

Cross-conjugated n-type polymer acceptors for efficient all-polymer solar cells

Cross-conjugated polymers with different side chains were developed as the electron accepting material for all-polymer solar cells.

Isoindigo-3,4-Difluorothiophene Polymer Acceptors Yield "All-Polymer" Bulk-Heterojunction Solar Cells with over 7 % Efficiency

Poly(isoindigo-alt-3,4-difluorothiophene) (PIID[2F]T) analogues used as "polymer acceptors" in bulk-heterojunction (BHJ) solar cells achieve >7 % efficiency when used in conjunction with the polymer donor PBFTAZ (model system; copolymer of benzo[1,2-b:4,5-b']dithiophene and 5,6-difluorobenzotriazole). Considering that most efficient polymer-acceptor alternatives to fullerenes (e.g. PC₆₁ BM or its C₇₁ derivative) are based on perylenediimide or naphthalenediimide motifs thus far, branched alkyl-substituted PIID[2F]T polymers are particularly promising non-fullerene candidates for "all-polymer" BHJ solar cells.

All-Polymer Solar Cells Based on a Conjugated Polymer Containing Siloxane-Functionalized Side Chains with Efficiency over 10

A novel wide-bandgap conjugated copolymer based on an imide-functionalized benzotriazole building block containing a siloxane-terminated side-chain is developed. This copolymer is successfully used to fabricate highly efficient all-polymer solar cells (all-PSCs) processed at room temperature with the green-solvent 2-methyl-tetrahydrofuran. When paired with a naphthalene diimide-based polymer electron-acceptor, the all-PSC exhibits a maximum power conversion efficiency (PCE) of 10.1%, which is the highest value so far reported for an all-PSC. Of particular interest is that the PCE remains 9.4% after thermal annealing at 80 °C for 24 h. The resulting high efficiency is attributed to a combination of high and balanced bulky charge carrier mobility, favorable face-on orientation, and high crystallinity. These observations indicate that the resulting copolymer can be a promising candidate toward high-performance all-PSCs for practical applications.

A Ladder-type Heteroheptacene 12H-Dithieno[2',3':4,5]thieno[3,2-b:2',3'-h]fluorene Based D-A Copolymer with Strong Intermolecular Interactions toward Efficient Polymer Solar Cells

Ladder-type electron-donating units for D-A copolymers applied in polymer solar cells usually comprise multiple tetrahedral carbon bridges bonded with out-of-plane alkyl chains for desirable solubility for device processing. However, molecular packing of resultant copolymers in the solid state and charge transport within devices are also impeded in spite of with multiple fused aromatic backbones. To mitigate this issue, a structurally well-defined ladder-type electron-donating heteroheptacene, 12H-dithieno[2',3':4,5]thieno[3,2-b:2',3'-h]fluorene (DTTF) with an extended conjugated backbone and a single tetrahedral carbon bridge attached with two bulky alkyl chains was designed and synthesized. The copolymerization of DTTF with 4,7-bis(4-hexylthiophen-2-yl)benzo[c][1,2,5]thiadiazole (DTBT) afforded a soluble D-A copolymer (PDTTF-DTBT) with a medium optical band gap of 1.72 eV and low-lying HOMO level at -5.36 eV. PDTTF-DTBT unprecedentedly exhibits strong intermolecular stacking ability and presents preferential face-on orientation on both ZnO and PEDOT:PSS layers. The improved packing order and appropriate phase separation of both the copolymer and PC₇₁BM in the bulk heterojunction blend on the ZnO layer over on the PEDOT:PSS layer lead to much improved power conversion efficiency of ∼8.2% in the inverted solar cell device, among the highest for reported ladder-type D-A copolymers. The research demonstrates that it is an effective method to incorporate a single tetrahedral carbon bridge to the molecular center of a ladder-type heteroacene with heavily extended π-conjugation to prepare D-A copolymers toward highly efficient PSCs.

Effect of Non-fullerene Acceptors' Side Chains on the Morphology and Photovoltaic Performance of Organic Solar Cells

Three indacenodithieno[3,2-b]thiophene (IT) cored small molecular acceptors (ITIC-SC6, ITIC-SC8, and ITIC-SC2C6) were synthesized, and the influence of side chains on their performances in solar cells was systematically probed. Our investigations have demonstrated the variation of side chains greatly affects the charge dissociation, charge mobility, and morphology of the donor:acceptor blend films. ITIC-SC2C6 with four branched side chains showed improved solubility, which can ensure the polymer donor to form favorable fibrous nanostructure during the drying of the blend film. Consequently, devices based on PBDB-ST:ITIC-SC2C6 demonstrated higher charge mobility, more effective exciton dissociation, and the optimal power conversion efficiency up to 9.16% with an FF of 0.63, a J_sc of 15.81 mA cm^-2, and a V_oc of 0.92 V. These results reveal that the side chain engineering is a valid way of tuning the morphology of blend films and further improving PCE in polymer solar cells.

Regulating Molecular Aggregations of Polymers via Ternary Copolymerization Strategy for Efficient Solar Cells

For many high-performance photovoltaic materials in polymer solar cells (PSCs), the active layers usually need to be spin-coated at high temperature due to the strong intermolecular aggregation of donor polymers, which is unfavorable in device repeatability and large-scale PSC printing. In this work, we adopted a ternary copolymerization strategy to regulate polymer solubility and molecular aggregation. A series of D-A₁-D-A₂ random polymers based on different acceptors, strong electron-withdrawing unit ester substituted thieno[3,4-b]thiophene (TT-E), and highly planar dithiazole linked TT-E (DTzTT) were constructed to realize the regulation of molecular aggregation and simplification of device fabrication. The results showed that as the relative proportion of TT-E segment in the backbone increased, the absorption evidently red-shifted with a gradually decreased aggregation in solution, eventually leading to the active layers that can be fabricated at low temperature. Furthermore, due to the excellent phase separation and low recombination, the optimized solar cells based on the terpolymer P1 containing 30% of TT-E segment exhibit high power conversion efficiency (PCE) of 9.09% with a significantly enhanced fill factor up to 72.86%. Encouragingly, the photovoltaic performance is insensitive to the fabrication temperature of the active layer, and it still could maintain high PCE of 8.82%, even at room temperature. This work not only develops the highly efficient photovoltaic materials for low temperature processed PSCs through ternary copolymerization strategy but also preliminarily constructs the relationship between aggregation and photovoltaic performance.

The effect of the backbone structure on the thermoelectric properties of donor–acceptor conjugated polymers

This work illustrated a relationship between backbone structure and thermoelectric properties through a study of three donor–acceptor (D–A)-structured conjugated polymers.