Electrochemical reduction of CO2 to CO using graphene oxide/carbon nanotube electrode in ionic liquid/acetonitrile system

Ionic Liquids in Metal, Photo-, Electro-, and (Bio) Catalysis

Ionic liquids (ILs) have unique physicochemical properties that make them advantageous for catalysis, such as low vapor pressure, non-flammability, high thermal and chemical stabilities, and the ability to enhance the activity and stability of (bio)catalysts. ILs can improve the efficiency, selectivity, and sustainability of bio(transformations) by acting as activators of enzymes, selectively dissolving substrates and products, and reducing toxicity. They can also be recycled and reused multiple times without losing their effectiveness. ILs based on imidazolium cation are preferred for structural organization aspects, with a semiorganized layer surrounding the catalyst. ILs act as a container, providing a confined space that allows modulation of electronic and geometric effects, miscibility of reactants and products, and residence time of species. ILs can stabilize ionic and radical species and control the catalytic activity of dynamic processes. Supported IL phase (SILP) derivatives and polymeric ILs (PILs) are good options for molecular engineering of greener catalytic processes. The major factors governing metal, photo-, electro-, and biocatalysts in ILs are discussed in detail based on the vast literature available over the past two and a half decades. Catalytic reactions, ranging from hydrogenation and cross-coupling to oxidations, promoted by homogeneous and heterogeneous catalysts in both single and multiphase conditions, are extensively reviewed and discussed considering the knowledge accumulated until now.

Fabrication of a biocathode for formic acid production upon the immobilization of formate dehydrogenase from Candida boidinii on a nanoporous carbon

The immobilization of the non-metallic enzyme formate dehydrogenase from Candida boidinii (CbFDH) into a nanoporous carbon with appropriate pore structure was explored for the bioelectrochemical conversion of CO₂ to formic acid (FA). Higher FA production rates were obtained upon immobilization of CbFDH compared to the performance of the enzyme in solution, despite the lower nominal CbFDH to NADH (β-nicotinamide adenine dinucleotide reduced) cofactor ratio and the lower amount of enzyme immobilized. The co-immobilization of the enzyme and a rhodium complex as mediator in the nanoporous carbon allowed the electrochemical regeneration of the cofactor. Preparative electrosynthesis of FA carried out on biocathodes of relatively large dimensions (ca. 3 cm × 2 cm) confirmed the higher production rate of FA for the immobilized enzyme. Furthermore, the incorporation of a Nafion binder in the biocathodes did not modify the immobilization extent of the CbFDH in the carbon support. Coulombic efficiencies close to 46% were obtained for the electrosynthesis carried out at -0.8 V for the biocathodes prepared using the lowest Nafion binder content and the co-immobilized enzyme and rhodium redox mediator. Although these values may yet be improved, they confirm the feasibility of these biocathodes in larger scales (6 cm²) beyond most common electrode dimensions reported in the literature (ca. a few mm²).

Acetonitrile Transition Metal Interfaces from First Principles

Acetonitrile is among the most commonly used nonaqueous solvents in catalysis and electrochemistry. We study its interfaces with multiple facets of the metals Ag, Cu, Pt, and Rh using density functional theory calculations; the structures reported shed new light on experimental observations and underscore the importance of solvent-solvent interactions at high coverage. We investigate the relationship of potential of zero charge (PZC) to metal work function, reporting results in agreement with experimental measurements. We develop a model to explain the effects of solvent chemisorption and orientation on the PZC to within a mean absolute deviation of 0.08-0.12 V for all facets studied. Our electrostatic field dependent phase diagram agrees with spectroscopic observations and sheds new light on electrostatic field effects. This work provides new insight into experimental observations on acetonitrile metal interfaces and provides guidance for future studies of acetonitrile and other nonaqueous solvent interfaces with transition metals.

Three-Dimensional Cathodes for Electrochemical Reduction of CO2: From Macro- to Nano-Engineering

Rising anthropogenic CO2 emissions and their climate warming effects have triggered a global response in research and development to reduce the emissions of this harmful greenhouse gas. The use of CO2 as a feedstock for the production of value-added fuels and chemicals is a promising pathway for development of renewable energy storage and reduction of carbon emissions. Electrochemical CO2 conversion offers a promising route for value-added products. Considerable challenges still remain, limiting this technology for industrial deployment. This work reviews the latest developments in experimental and modeling studies of three-dimensional cathodes towards high-performance electrochemical reduction of CO2. The fabrication-microstructure-performance relationships of electrodes are examined from the macro- to nanoscale. Furthermore, future challenges, perspectives and recommendations for high-performance cathodes are also presented.

A Mn-N3 single-atom catalyst embedded in graphitic carbon nitride for efficient CO2 electroreduction

Developing effective catalysts based on earth abundant elements is critical for CO₂ electroreduction. However, simultaneously achieving a high Faradaic efficiency (FE) and high current density of CO (j_CO) remains a challenge. Herein, we prepare a Mn single-atom catalyst (SAC) with a Mn-N₃ site embedded in graphitic carbon nitride. The prepared catalyst exhibits a 98.8% CO FE with a j_CO of 14.0 mA cm^-2 at a low overpotential of 0.44 V in aqueous electrolyte, outperforming all reported Mn SACs. Moreover, a higher j_CO of 29.7 mA cm^-2 is obtained in an ionic liquid electrolyte at 0.62 V overpotential. In situ X-ray absorption spectra and density functional theory calculations demonstrate that the remarkable performance of the catalyst is attributed to the Mn-N₃ site, which facilitates the formation of the key intermediate COOH^* through a lowered free energy barrier.

In Situ Scanning Tunneling Microscopy of Cobalt-Phthalocyanine-Catalyzed CO2 Reduction Reaction

We report a molecular investigation of a cobalt phthalocyanine (CoPc)-catalyzed CO₂ reduction reaction by electrochemical scanning tunneling microscopy (ECSTM). An ordered adlayer of CoPc was prepared on Au(111). Approximately 14 % of the adsorbed species appeared with high contrast in a CO₂ -purged electrolyte environment. The ECSTM experiments indicate the proportion of high-contrast species correlated with the reduction of Co^II Pc (-0.2 V vs. saturated calomel electrode (SCE)). The high-contrast species is ascribed to the CoPc-CO₂ complex, which is further confirmed by theoretical simulation. The sharp contrast change from CoPc-CO₂ to CoPc is revealed by in situ ECSTM characterization of the reaction. Potential step experiments provide dynamic information for the initial stage of the reaction, which include the reduction of CoPc and the binding of CO₂ , and the latter is the rate-limiting step. The rate constant of the formation and dissociation of CoPc-CO₂ is estimated on the basis of the in situ ECSTM experiment.

Directly writing flexible temperature sensor with graphene nanoribbons for disposable healthcare devices

A flexible temperature sensor is developed by directly writing or mask spraying commonly-used paper with graphene nanoribbon ink. The sensor is ultralow cost, degradable, and highly promising as a disposable device for personal healthcare.

Solvents and Supporting Electrolytes in the Electrocatalytic Reduction of CO2

Different electrolytes applied in the aqueous electrocatalytic CO₂ reduction reaction (CO₂RR) considerably influence the catalyst performance. Their concentration, species, buffer capacity, and pH value influence the local reaction conditions and impact the product distribution of the electrocatalyst. Relevant properties of prospective solvents include their basicity, CO₂ solubility, conductivity, and toxicity, which affect the CO₂RR and the applicability of the solvents. The complexity of an electrochemical system impedes the direct correlation between a single parameter and cell performance indicators such as the Faradaic efficiency; thus the effects of different electrolytes are often not fully comprehended. For an industrial application, a deeper understanding of the effects described in this review can help with the prediction of performance, as well as the development of scalable electrolyzers. In this review, the application of supporting electrolytes and different solvents in the CO₂RR reported in the literature are summarized and discussed.

Superaerophilic copper nanowires for efficient and switchable CO2 electroreduction

Copper is one of the most efficient electrocatalysts for switchable carbon dioxide conversion, but the design of an advanced Cu-based catalyst with high selectivity while suppressing hydrogen evolution remains a great challenge. Herein, we use Cu nanowires (Cu NWs) as the starting materials and polytetrafluoroethylene (PTFE) as the surface modifier to make a superaerophilic electrode using a wettability control strategy. This strategy allows tuning of the selectivity of the CO₂ reduction reaction (CO₂RR) and a decrease of the hydrogen evolution rate simultaneously by facilitating the supply of CO₂ reactants and inhibiting the adsorption of water (protons). The transferring point from a pinning to bursting state turned out to be the optimized condition leading to the highest CO₂RR faradaic efficiency without significant interference of current density. The optimized superaerophilic Cu NW catalyst showed CO-selectivity with a Faraday efficiency of 71% at -0.4 V vs. RHE and HCOOH-selectivity with a Faraday efficiency of 68% at -0.6 V vs. RHE. Moreover, the accelerated gas and ion diffusion and homogenized reactions also avoided accumulative damage on the surface of the Cu NWs and enhanced the stability of the Cu catalyst. This wettability tuning strategy provides a facile and efficient way to optimize the gas and ion diffusion layers, therefore promoting the performance of the CO₂RR. This strategy potentially can be extended to the design of other gas consumption electrocatalysts.

Surface Immobilization of Transition Metal Ions on Nitrogen-Doped Graphene Realizing High-Efficient and Selective CO2 Reduction

Electrochemical conversion of CO₂ to value-added chemicals using renewable electricity provides a promising way to mitigate both global warming and the energy crisis. Here, a facile ion-adsorption strategy is reported to construct highly active graphene-based catalysts for CO₂ reduction to CO. The isolated transition metal cyclam-like moieties formed upon ion adsorption are found to contribute to the observed improvements. Free from the conventional harsh pyrolysis and acid-leaching procedures, this solution-chemistry strategy is easy to scale up and of general applicability, thus paving a rational avenue for the design of high-efficiency catalysts for CO₂ reduction and beyond.

Progress and Perspective of Electrocatalytic CO2 Reduction for Renewable Carbonaceous Fuels and Chemicals

The worldwide unrestrained emission of carbon dioxide (CO2) has caused serious environmental pollution and climate change issues. For the sustainable development of human civilization, it is very desirable to convert CO2 to renewable fuels through clean and economical chemical processes. Recently, electrocatalytic CO2 conversion is regarded as a prospective pathway for the recycling of carbon resource and the generation of sustainable fuels. In this review, recent research advances in electrocatalytic CO2 reduction are summarized from both experimental and theoretical aspects. The referred electrocatalysts are divided into different classes, including metal-organic complexes, metals, metal alloys, inorganic metal compounds and carbon-based metal-free nanomaterials. Moreover, the selective formation processes of different reductive products, such as formic acid/formate (HCOOH/HCOO-), monoxide carbon (CO), formaldehyde (HCHO), methane (CH4), ethylene (C2H4), methanol (CH3OH), ethanol (CH3CH2OH), etc. are introduced in detail, respectively. Owing to the limited energy efficiency, unmanageable selectivity, low stability, and indeterminate mechanisms of electrocatalytic CO2 reduction, there are still many tough challenges need to be addressed. In view of this, the current research trends to overcome these obstacles in CO2 electroreduction field are summarized. We expect that this review will provide new insights into the further technique development and practical applications of CO2 electroreduction.

Heterogeneous electrochemical CO2 reduction using nonmetallic carbon-based catalysts: current status and future challenges

Electrochemical CO₂ reduction (ECR) offers an important pathway for renewable energy storage and fuels production. It still remains a challenge in designing highly selective, energy-efficient, robust, and cost-effective electrocatalysts to facilitate this kinetically slow process. Metal-free carbon-based materials have features of low cost, good electrical conductivity, renewability, diverse structure, and tunability in surface chemistry. In particular, surface functionalization of carbon materials, for example by doping with heteroatoms, enables access to unique active site architectures for CO₂ adsorption and activation, leading to interesting catalytic performances in ECR. We aim to provide a comprehensive review of this category of metal-free catalysts for ECR, providing discussions and/or comparisons among different nonmetallic catalysts, and also possible origin of catalytic activity. Fundamentals and some future challenges are also described.