Cell adhesive spectra along surface wettability gradient from superhydrophilicity to superhydrophobicity

Titania (TiO2) nanotube surfaces doped with zinc and strontium for improved cell compatibility

Titanium-based orthopedic implants are gaining popularity in recent years due to their excellent biocompatibility, superior corrosion resistance and lightweight properties. However, these implants often fail to perform effectively due to poor osseointegration. Nanosurface modification approaches may help to resolve this problem. In this work, TiO2 nanotube (NT) arrays were fabricated on commercially available pure titanium (Ti) surfaces by anodization and annealing. Then, zinc (Zn) and strontium (Sr), important for cell signaling, were doped on the NT surface by hydrothermal treatment. This very simple method of Zn and Sr doping takes less time and energy compared to other complicated techniques. Different surface characterization tools such as scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), energy-dispersive X-ray spectroscopy (EDS), static water contact angle, X-ray diffraction (XRD) and nanoindentation techniques were used to evaluate the modified surfaces. Then, adipose derived stem cells (ADSCs) were cultured with the surfaces to evaluate cell adhesion, proliferation, and growth on the surfaces. After that, the cells were differentiated towards osteogenic lineage to evaluate alkaline phosphatase (ALP) activity, osteocalcin expression, and calcium phosphate mineralization. Results indicate that NT surfaces doped with Zn and Sr had significantly enhanced ADSC adhesion, proliferation, growth, and osteogenic differentiation compared to an unmodified surface, thus confirming the enhanced performance of these surfaces.

A chitosan-coated PCL/nano-hydroxyapatite aerogel integrated with a nanofiber membrane for providing antibacterial activity and guiding bone regeneration

A guided bone regeneration (GBR) membrane can act as a barrier to prevent the invasion and interference from foreign soft tissues, promoting infiltration and proliferation of osteoblasts in the bone defect area. Herein, a composite scaffold with dual functions of osteogenesis and antibacterial effects was prepared for GBR. A polycaprolactone (PCL)/nano-hydroxyapatite (n-HA) aerogel produced by electrospinning and freeze-drying techniques was fabricated as the loose layer of the scaffold, while a PCL nanofiber membrane was used as the dense layer. Chitosan (CS) solution served as a middle layer to provide mechanical support and antibacterial effects between the two layers. Morphological results showed that the loose layer had a porous structure with n-HA successfully dispersed in the aerogels, while the dense layer possessed a sufficiently dense structure. In vitro antibacterial experiments illustrated that the CS solution in the middle layer stabilized the scaffold structure and endowed the scaffold with good antibacterial properties. The cytocompatibility results indicated that both fibroblasts and osteoblasts exhibited superior cell activity on the dense and loose layers, respectively. In particular, the dense layer made of nanofibers could work as a barrier layer to inhibit the infiltration of fibroblasts into the loose layer. In vitro osteogenesis analysis suggested that the PCL/n-HA aerogel could enhance the bone induction ability of bone mesenchymal stem cells, which was confirmed by the increased expression of the alkaline phosphatase activity. The loose structure facilitated the infiltration and migration of bone mesenchymal stem cells for better osteogenesis. In summary, such a composite scaffold exhibited excellent osteogenic and antibacterial properties as well as the barrier effect, thus holding promising potential for use as GBR materials.

Nanostructured graphene oxide enriched with metallic nanoparticles as a biointerface to enhance cell adhesion through mechanosensory modifications

Nanostructuring is a process involving surface manipulation at the nanometric level, which improves the mechanical and biological properties of biomaterials. Specifically, it affects the mechanotransductive perception of the microenvironment of cells. Mechanical force conversion into an electrical or chemical signal contributes to the induction of a specific cellular response. The relationship between the cells and growth surface induces a biointerface-modifying cytophysiology and consequently a therapeutic effect. In this study, we present the fabrication of graphene oxide (GO)-based nanofilms decorated with metallic nanoparticles (NPs) as potential coatings for biomaterials. Our investigation showed the effect of decorating GO with metallic NPs for the modification of the physicochemical properties of nanostructures in the form of nanoflakes and nanofilms. A comprehensive biocompatibility screening panel revealed no disturbance in the metabolic activity of human fibroblasts (HFFF2) and bone marrow stroma cells (HS-5) cultivated on the GO nanofilms decorated with gold and copper NPs, whereas a significant cytotoxic effect of the GO nanocomplex decorated with silver NPs was demonstrated. The GO nanofilm decorated with gold NPs beneficially managed early cell adhesion as a result of the transient upregulation of α1β5 integrin expression, acceleration of cellspreading, and formation of elongated filopodia. Additionally, the cells, sensing the substrate derived from the nanocomplex enriched with gold NPs, showed reduced elasticity and altered levels of vimentin expression. In the future, GO nanocomplexes decorated with gold NPs can be incorporated in the structure of architecturally designed biomimetic biomaterials as biocompatible nanostructuring agents with proadhesive properties.

Recent Advances in Superhydrophobic and Antibacterial Cellulose-Based Fibers and Fabrics: Bio-inspiration, Strategies, and Applications

Cellulose-based fabrics are ubiquitous in our daily lives. They are the preferred choice for bedding materials, active sportswear, and next-to-skin apparels. However, the hydrophilic and polysaccharide characteristics of cellulose materials make them vulnerable to bacterial attack and pathogen infection. The design of antibacterial cellulose fabrics has been a long-term and on-going effort. Fabrication strategies based on the construction of surface micro-/nanostructure, chemical modification, and the application of antibacterial agents have been extensively investigated by many research groups worldwide. This review systematically discusses recent research on super-hydrophobic and antibacterial cellulose fabrics, focusing on morphology construction and surface modification. First, natural surfaces showing liquid-repellent and antibacterial properties are introduced and the mechanisms behind are explained. Then, the strategies for fabricating super-hydrophobic cellulose fabrics are summarized, and the contribution of the liquid-repellent function to reducing the adhesion of live bacteria and removing dead bacteria is elucidated. Representative studies on cellulose fabrics functionalized with super-hydrophobic and antibacterial properties are discussed in detail, and their potential applications are also introduced. Finally, the challenges in achieving super-hydrophobic antibacterial cellulose fabrics are discussed, and the future research direction in this area is proposed.

Graphical Abstract

The figure summarizes the natural surfaces and the main fabrication strategies of superhydrophobic antibacterial cellulose fabrics and their potential applications.

Supplementary Information

The online version contains supplementary material available at 10.1007/s42765-023-00297-1.

Wetting of Cell Aggregates on Microdisk Topography Structures Achieved by Maskless Optical Projection Lithography

Cell aggregates as a 3D culture model can effectively mimic the physiological processes such as embryonic development, immune response, and tissue renewal in vivo. Researches show that the topography of biomaterials plays an important role in regulating cell proliferation, adhesion, and differentiation. It is of great significance to understand how cell aggregates respond to surface topography. Herein, microdisk array structures with the optimized size are used to investigate the wetting of cell aggregates. Cell aggregates exhibit complete wetting with distinct wetting velocities on the microdisk array structures of different diameters. The wetting velocity of cell aggregates reaches a maximum of 293 µm h^-1 on microdisk structures with a diameter of 2 µm and is a minimum of 247 µm h^-1 on microdisk structures of 20 µm diameter, which suggests that the cell-substrates adhesion energy on the latter is smaller. Actin stress fibers, focal adhesions (FAs), and cell morphology are analyzed to reveal the mechanisms of variation of wetting velocity. Furthermore, it is demonstrated that cell aggregates adopt climb and detour wetting modes on small and large-sized microdisk structures, respectively. This work reveals the response of cell aggregates to micro-scale topography, providing guidance for better understanding of tissue infiltration.

Effects of Micro-Arc Oxidation Discharge Parameters on Formation and Biomedical Properties of Hydroxyapatite-Containing Flower-like Structure Coatings

The micro-arc oxidation (MAO) process was used to prepare hydroxyapatite-containing flower-like structure coatings on commercially pure titanium substrates with various values of the applied voltage (330, 390, 450 V), applied current (0.4, 0.5, 0.6 A), and duration time (1, 3, 5 min). It was found that the surface morphology of the coatings was determined primarily by the applied voltage. A voltage of 330 V yielded a flower-like/plate-like structure, while voltages of 390 V and 450 V produced a flower-like structure and a porous morphology, respectively. The applied current and duration time mainly affected the coating formation speed and petal size of the flower-like structures, respectively. The coatings prepared using voltages of 330 V and 390 V (0.6 A, 5 min) both contained Ti, TiO₂-A (anatase), TiO₂-R (rutile), DCPD (CaHPO₄·2H₂O, calcium hydrogen phosphate), and hydroxyapatite (HA). However, the latter coating contained less DCPD and had a higher HA/DCPD ratio and a Ca/P ratio closer to the ideal value of HA. The coating prepared with a voltage of 450 V consisted mainly of Ti, TiO₂-A, TiO₂-R, and CaTiO₃. For the coatings prepared with a voltage of 390 V, the flower-like structures consisted mainly of HA-containing compounds. DCPD plate-like structures were observed either between the HA-containing flower-like structures (330 V samples) or within the flower-like structures themselves (390 V samples). The coating surfaces with flower-like/plate-like or flower-like structures had a greater roughness, which increased their hydrophilicity and resulted in superior bioactivity (SBF immersion) and biocompatibility (MG-63 cell culture). The optimal biomedical performance was found in the 390 V coating due to its flower-like structure and high HA/DCPD ratio.

Recent Advances in Macroporous Hydrogels for Cell Behavior and Tissue Engineering

Hydrogels have been extensively used as scaffolds in tissue engineering for cell adhesion, proliferation, migration, and differentiation because of their high-water content and biocompatibility similarity to the extracellular matrix. However, submicron or nanosized pore networks within hydrogels severely limit cell survival and tissue regeneration. In recent years, the application of macroporous hydrogels in tissue engineering has received considerable attention. The macroporous structure not only facilitates nutrient transportation and metabolite discharge but also provides more space for cell behavior and tissue formation. Several strategies for creating and functionalizing macroporous hydrogels have been reported. This review began with an overview of the advantages and challenges of macroporous hydrogels in the regulation of cellular behavior. In addition, advanced methods for the preparation of macroporous hydrogels to modulate cellular behavior were discussed. Finally, future research in related fields was discussed.

Advances in precise single-cell capture for analysis and biological applications

Cells are the basic structural and functional units of living organisms. However, conventional cell analysis only averages millions of cell populations, and some important information is lost. It is essential to quantitatively characterize the physiology and pathology of single-cell activities. Precise single-cell capture is an extremely challenging task during cell sample preparation. In this review, we summarize the category of technologies to capture single cells precisely with a focus on the latest development in the last five years. Each technology has its own set of benefits and specific challenges, which provide opportunities for researchers in different fields. Accordingly, we introduce the applications of captured single cells in cancer diagnosis, analysis of metabolism and secretion, and disease treatment. Finally, some perspectives are provided on the current development trends, future research directions, and challenges of single-cell capture.

Antagonistically Functionalized Diatom Biosilica for Bio-Triboelectric Generators

Although biomaterial-based triboelectric nanogenerators (Bio-TENGs) for use in wearable electronics and implantable sensors have been developed, power generation is not suitable for satisfying the basic requirements for practical applications. Here, to greatly enhance output performances of Bio-TENG devices, an antagonistic approach of diatom frustules (DFs) with amine and fluorine chemical functionalizations is reported. The DFs are treated with piranha solution to increase the density of hydroxyl groups and tribo-positive and tribo-negative composite films are designed with antagonistically functionalized DFs. The tribo-positive composites having electron donating functionality consist of aminated DFs and cellulose nanocrystals (CNCs), while the tribo-negative composite is composed of fluorinated DFs and polydimethylsiloxane (PDMS). An antagonistically and chemically functionalized TENG (ACF TENG) with an efficient contact area of 9.6 cm² under a force of 8 N and a frequency of 5 Hz exhibits an output voltage of 248 V, a short-circuit current of 16.4 µA, and a power density of 2.01 W m^-2 , which is 16.6 times higher than a reference (CNC:PDMS) TENG. This study shows a simple antagonistic approach for chemical functionalization as an efficient method to manipulate the tribo-polarity of bio-additives for enhancing power generation of Bio-TENGs.

Surface Treatment and Bioinspired Coating for 3D-Printed Implants

Three-dimensional (3D) printing technology has developed rapidly and demonstrates great potential in biomedical applications. Although 3D printing techniques have good control over the macrostructure of metallic implants, the surface properties have superior control over the tissue response. By focusing on the types of surface treatments, the osseointegration activity of the bone-implant interface is enhanced. Therefore, this review paper aims to discuss the surface functionalities of metallic implants regarding their physical structure, chemical composition, and biological reaction through surface treatment and bioactive coating. The perspective on the current challenges and future directions for development of surface treatment on 3D-printed implants is also presented.

Deciphering controversial results of cell proliferation on TiO2 nanotubes using machine learning

With the rapid development of biomedical sciences, contradictory results on the relationships between biological responses and material properties emerge continuously, adding to the challenge of interpreting the incomprehensible interfacial process. In the present paper, we use cell proliferation on titanium dioxide nanotubes (TNTs) as a case study and apply machine learning methodologies to decipher contradictory results in the literature. The gradient boosting decision tree model demonstrates that cell density has a higher impact on cell proliferation than other obtainable experimental features in most publications. Together with the variation of other essential features, the controversy of cell proliferation trends on various TNTs is understandable. By traversing all combinational experimental features and the corresponding forecast using an exhausted grid search strategy, we find that adjusting cell density and sterilization methods can simultaneously induce opposite cell proliferation trends on various TNTs diameter, which is further validated by experiments. This case study reveals that machine learning is a burgeoning tool in deciphering controversial results in biomedical researches, opening up an avenue to explore the structure-property relationships of biomaterials.

Bioinspired wettable-nonwettable micropatterns for emerging applications

Superhydrophilic and superhydrophobic surfaces are prevalent in nature and have received tremendous attention due to their importance in both fundamental research and practical applications. With the high interdisciplinary research and great development of microfabrication techniques, artificial wettable-nonwettable micropatterns inspired by the water-collection behavior of desert beetles have been successfully fabricated. A combination of the two extreme states of superhydrophilicity and superhydrophobicity on the same surface precisely, wettable-nonwettable micropatterns possess unique functionalities, such as controllable superwetting, anisotropic wetting, oriented adhesion, and other properties. In this review, we briefly describe the methods for fabricating wettable-nonwettable patterns, including self-assembly, electrodeposition, inkjet printing, and photolithography. We also highlight some of the emerging applications such as water collection, controllable bioadhesion, cell arrays, microreactors, printing techniques, and biosensors combined with various detection methods. Finally, the current challenges and prospects of this renascent and rapidly developing field are proposed and discussed.

Evaluation of the anti-oxidative and ROS scavenging properties of biomaterials coated with epigallocatechin gallate for tissue engineering

In tissue engineering, excessively generated reactive oxygen species (ROS) during biomaterial implantation or cell transplantation is a one of major causes of diminishing therapeutic effects. In this study, we prepared biomaterial surfaces coated with antioxidant epigallocatechin gallate (EGCG) and metal ions, and evaluated their anti-oxidative and ROS scavenging properties. We revealed that EGCG-coating on polycaprolactone (PCL) film surface increased hydrophilicity and anti-oxidative properties as a function of total phenol content (TPC) potentially due to the increase in phenolic -OH and π-electrons from structural maintenance and directly removed the hydrogen peroxide (H₂O₂) by resonance-stabilization. Furthermore, EGCG-coated PCL film increased attachment, spreading area, and viability of human adipose-derived stem cells (hADSCs) against H₂O₂ treatment while stimulated the cellular signaling to reduce apoptotic gene and enhance anti-oxidative enzyme expression. Further, we applied EGCG coating on the surface of poly-L-lactic acid (PLLA) fibers. Spheroids incorporating EGCG-coated PLLA fibers were able to maintain their shape and showed improved viability and anti-oxidative activities in response to H₂O₂-induced oxidative stress than control spheroids. Therefore, metal-phenolic network (MPN) coating of EGCG is a suitable method to impart the anti-oxidative properties to biomaterials by evaluating the structural properties and biological effects.

Bio-inspired wettability patterns for biomedical applications

Benefiting from the remarkable wettability heterogeneity, bio-inspired wettability patterns present a progressive and versatile platform for manipulating and patterning liquids, which provides an emerging strategy for operating liquid samples with crucial values in biomedical applications. In this review, we present a general summary of bio-inspired wettability patterns. After a compendious introduction of natural wettability phenomena and their underlying mechanisms, we summarize the general design principles and fabrication methods for preparing artificial wettability materials. Next, we shift to patterned surface wettability with an emphasis on the fabrication approaches. Then, we discuss in detail the various practical applications of wettability patterns in the biomedical field, including cell culture, drug screening and biosensors. Critical thinking about the current challenges and future outlook is also provided. We believe that this review would propel the prosperous development of bio-inspired wettability patterns to flourish in the field of biomedical engineering.

Bioinspired surfaces with wettability: biomolecule adhesion behaviors

Surface wettability plays an important role in regulating biomolecule adhesion behaviors. The biomolecule adhesion behaviors of superwettable surfaces have become an important topic as an important part of the interactions between materials and organisms. In addition to general research on the moderate wettability of surfaces, the studies of biomolecule adhesion behaviors extend to extreme wettability ranges such as superhydrophobic, superhydrophilic and slippery surfaces and attract both fundamental and practical interest. In this review, we summarize the recent studies on biomolecule adhesion behaviors on superwettable surfaces, especially superhydrophobic, superhydrophilic and slippery surfaces. The first part will focus on the influence of extreme wettability on cell adhesion behaviors. The second part will concentrate on the adhesion behaviors of biomacromolecules on superwettable surfaces including proteins and nucleic acids. Finally, the influences of wettability on small molecule adhesion behaviors on material surfaces have also been investigated. The mechanism of superwettable surfaces and their influences on biomolecule adhesion behaviors have been studied and highlighted.

Collagen/Chitosan Functionalization of Complex 3D Structures Fabricated by Laser Direct Writing via Two-Photon Polymerization for Enhanced Osteogenesis

The fabrication of 3D microstructures is under continuous development for engineering bone substitutes. Collagen/chitosan (Col/CT) blends emerge as biomaterials that meet the mechanical and biological requirements associated with bone tissue. In this work, we optimize the osteogenic effect of 3D microstructures by their functionalization with Col/CT blends with different blending ratios. The structures were fabricated by laser direct writing via two-photons polymerization of IP-L780 photopolymer. They comprised of hexagonal and ellipsoidal units 80 µm in length, 40 µm in width and 14 µm height, separated by 20 µm pillars. Structures’ functionalization was achieved via dip coating in Col/CT blends with specific blending ratios. The osteogenic role of Col/CT functionalization of the 3D structures was confirmed by biological assays concerning the expression of alkaline phosphatase (ALP) and osteocalcin secretion as osteogenic markers and Alizarin Red (AR) as dye for mineral deposits in osteoblast-like cells seeded on the structures. The structures having ellipsoidal units showed the best results, but the trends were similar for both ellipsoidal and hexagonal units. The strongest osteogenic effect was obtained for Col/CT blending ratio of 20/80, as demonstrated by the highest ALP activity, osteocalcin secretion and AR staining intensity in the seeded cells compared to all the other samples.

Microcarriers for Upscaling Cultured Meat Production

Due to the considerable environmental impact and the controversial animal welfare associated with industrial meat production, combined with the ever-increasing global population and demand for meat products, sustainable production alternatives are indispensable. In 2013, the world's first laboratory grown hamburger made from cultured muscle cells was developed. However, coming at a price of $300.000, and being produced manually, substantial effort is still required to reach sustainable large-scale production. One of the main challenges is scalability. Microcarriers (MCs), offering a large surface/volume ratio, are the most promising candidates for upscaling muscle cell culture. However, although many MCs have been developed for cell lines and stem cells typically used in the medical field, none have been specifically developed for muscle stem cells and meat production. This paper aims to discuss the MCs' design criteria for skeletal muscle cell proliferation and subsequently for meat production based on three scenarios: (1) MCs are serving only as a temporary substrate for cell attachment and proliferation and therefore they need to be separated from the cells at some stage of the bioprocess, (2) MCs serve as a temporary substrate for cell proliferation but are degraded or dissolved during the bioprocess, and (3) MCs are embedded in the final product and therefore need to be edible. The particularities of each of these three bioprocesses will be discussed from the perspective of MCs as well as the feasibility of a one-step bioprocess. Each scenario presents advantages and drawbacks, which are discussed in detail, nevertheless the third scenario appears to be the most promising one for a production process. Indeed, using an edible material can limit or completely eliminate dissociation/degradation/separation steps and even promote organoleptic qualities when embedded in the final product. Edible microcarriers could also be used as a temporary substrate similarly to scenarios 1 and 2, which would limit the risk of non-edible residues.

Influence of polydimethylsiloxane substrate stiffness on corneal epithelial cells

Many cell types are known to modulate their behaviour in response to changes in material stiffness; however, little is known about how stiffness affects corneal epithelial cells. This study aims to investigate the response of a corneal epithelial cell line to polydimethylsiloxane (PDMS) substrates with a range of Young's moduli from 10 to 1500 kPa. Cellular morphology, proliferation, differentiation and mechanobiology were examined. Cells grown on PDMS adopted the typical cobblestone morphology exhibited by the corneal epithelium. Proliferative markers pERK and Ki67 were higher in cells cultured on stiffer substrates compared with those on softer substrates. Material stiffness was also found to influence the cell phenotype with cells on stiffer substrates having higher cytokeratin 3 gene expression, a mature epithelial marker, while cells on softer substrates expressed more cytokeratin 14, a basal epithelial marker. Cells grown on softer substrates also displayed higher levels of focal adhesions and intermediate filaments compared with cells on stiff substrates. This research will aid in designing novel biomaterials for the culture and transplantation of corneal epithelial cells.

Biofunctionalization of metallic implants by calcium phosphate coatings

Metallic materials have been extensively applied in clinical practice due to their unique mechanical properties and durability. Recent years have witnessed broad interests and advances on surface functionalization of metallic implants for high-performance biofunctions. Calcium phosphates (CaPs) are the major inorganic component of bone tissues, and thus owning inherent biocompatibility and osseointegration properties. As such, they have been widely used in clinical orthopedics and dentistry. The new emergence of surface functionalization on metallic implants with CaP coatings shows promise for a combination of mechanical properties from metals and various biofunctions from CaPs. This review provides a brief summary of state-of-art of surface biofunctionalization on implantable metals by CaP coatings. We first glance over different types of CaPs with their coating methods and in vitro and in vivo performances, and then give insight into the representative biofunctions, i.e. osteointegration, corrosion resistance and biodegradation control, and antibacterial property, provided by CaP coatings for metallic implant materials.

Superhydrophobicity: advanced biological and biomedical applications

The biological and biomedical applications of superhydrophobic surface.

A proteomics study to explore the role of adsorbed serum proteins for PC12 cell adhesion and growth on chitosan and collagen/chitosan surfaces

The aim of this article is to apply proteomics in the comparison of the molecular mechanisms of PC12 cell adhesion and growth mediated by the adsorbed serum proteins on the surfaces of chitosan and collagen/chitosan films. First, the chitosan and the collagen/chitosan films were prepared by spin coating; and their surface morphologies were characterized by scanning electron microscopy, X-ray energy dispersive spectroscopy, contact angle measurement and Fourier transform infrared spectroscopy. Subsequently, cell proliferation experiments on two materials were performed and the dynamic curves of protein adsorption on their surfaces were measured. Then, proteomics and bioinformatics were used to analyze and compare the adsorbed serum proteins on the surfaces of two biomaterials; and their effects on cell adhesion were discussed. The results showed that the optimum concentration of chitosan film was 2% w/v. When compared with chitosan film, collagen/chitosan film promoted the growth and proliferation of PC12 cells more significantly. Although the dynamic curves showed no significant difference in the total amount of the adsorbed proteins on both surfaces, proteomics and bioinformatics analyses revealed a difference in protein types: the chitosan surface adsorbed more vitronectin whereas collagen/chitosan surface adsorbed more fibronectin 1 and contained more cell surface receptor binding sites and more Leu-Asp-Val sequences in its surface structure; the collagen/chitosan surface were more conducive to promoting cell adhesion and growth.

Janus Gradient Meshes for Continuous Separation and Collection of Flowing Oils under Water

Gradient meshes with Janus wettabilities are fabricated to stably separate and collect spilled oils from a range of flowing oily wastewater. Here, we demonstrate an overflow with separation methodology, which combines selective oil overflow and membrane separation, to separate low content oils from dynamic flowing oil-water mixtures by a curved gradient mesh that covered on a solid edge. The microscaled air-oil-water-solid four-phase wetting state during the oil-water separation process is visualized and demonstrated. The fundamental understanding of this overflow with separation system and the superior gradient mesh materials would enable us to construct a wide variety of separation devices out of traditional designs and advance related applications, such as wastewater treatment and fuel purification.