Cold Plasma: an Alternative Technology for the Starch Modification

Effect of plasma-activated water on the supramolecular structure and techno-functional properties of starch: A review

This review discusses the changes in the multi-scale structure and functionality of starch after its hydrothermal modification using plasma-activated water (PAW). PAW contains reactive species that decrease the pH of the water and increase the oxidation-reduction potential, which promotes the oxidation and degradation of the surface of the starch granules to varying extents, depending on the botanical source and treatment conditions. In this article, we compile the information published so far on the effects of using PAW during heat-moisture and annealing treatments and discuss the results of the substitution of water with PAW on the long and short-range crystallinity, helical order, thermal behavior, functional properties, and digestibility. Additionally, we highlighted the possible application of PAW-modified starches. Finally, we provided an overview of future challenges, suggesting several potential directions to understand the mechanisms behind PAW use for developing sustainable modified starches for the food industry.

Dielectric barrier discharge plasma pre-treatment to facilitate the acetylation process of corn starch under heating/cooling cycles

The objective of the current work was to evaluate the impacts of dielectric barrier discharge plasma and repeated dry-heat treatments on the acetylation process of corn starch. The combined modification resulted in a higher substitution degree of acetate groups on starch chains compared to the acetylation treatment alone. This outcome was linked to the increase in surface area and structural organization level of granules achieved through the application of plasma and heating/cooling cycles, respectively. The successful esterification of starch structure was verified through FTIR (1710 cm-1) and 1H NMR (2 ppm). With the increase in plasma treatment duration up to 20 min, gelatinization enthalpy increased (10.81 J/g) due to the cross-linking reaction. Starch acetate produced through the combined treatment could find the application in the development of low-calorie food formulations due to its high resistant starch (70.5 g/100 g) and low viscosity (43 mPa s).

The effect of cold plasma on starch: Structure and performance

The inherent side effects of the physico-chemical properties of native starches often severely limit their use in food and non-food industries. Plasma is a non-thermal technology that allows rapid improvement of functional properties. This review provides a comprehensive summary of the sources and mechanisms of action of cold plasma and assesses its effects on starch morphology, crystal structure, molecular chain structure and physicochemical properties. The complex relationship between structure and function of plasma-treated starch is also explored. Potential applications of plasma-modified starch are also discussed in detail. The outcome of the modification process is influenced by factors such as starch type and concentration, plasma source, intensity and duration. The properties of starch can be effectively optimised using plasma technology. Plasma-based technologies therefore have the potential to modify starch to create a range of functionalities to meet the growing market demand for clean label ingredients.

Research progress on the regulation of starch-polyphenol interactions in food processing

Starch is a fundamental material in the food industry. However, the inherent structural constraints of starch impose limitations on its physicochemical properties, including thermal instability, viscosity, and retrogradation. To address these obstacles, polyphenols are extensively employed for starch modification owing to their distinctive structural characteristics and potent antioxidant capabilities. Interaction between the hydroxyl groups of polyphenols and starch results in the formation of inclusion or non-inclusion complexes, thereby inducing alterations in the multiscale structure of starch. These modifications lead to changes in the physicochemical properties of starch, while simultaneously enhancing its nutritional value. Recent studies have demonstrated that both thermal and non-thermal processing exert a significant influence on the formation of starch-polyphenol complexes. This review meticulously analyzes the techniques facilitating complex formation, elucidating the critical factors that dictate this process. Of noteworthy importance is the observation that thermal processing significantly boosts these interactions, whereas non-thermal processing enables more precise modifications. Thus, a profound comprehension and precise regulation of the production of starch-polyphenol complexes are imperative for optimizing their application in various starch-based food products. This in-depth study is dedicated to providing a valuable pathway for enhancing the quality of starchy foods through the strategic integration of suitable processing technologies.

Advancements in Pulse Starches: Exploring Non-Thermal Modification Methods

The surge in the global demand for plant-based proteins has catapulted pulse protein into the spotlight. To ensure economic viability and sustainable production, it is crucial to utilize pulse starch, a by-product of plant protein fractionation. Despite the increasing interest in pulse starches, there is a notable gap in knowledge regarding their modifications and applications compared to cereal and tuber starches. Non-thermal techniques such as electron beam radiation, static high pressure, microfluidization, and cold plasma are emerging as innovative methods for starch modification. These techniques offer significant advantages, including enhanced safety, environmental sustainability, and the development of unique functional properties unattainable through conventional methods. However, challenges such as equipment availability, high costs, and energy consumption hinder their widespread adoption. In light of the growing emphasis on "clean and green labelling" and effective "waste management" in food production, evaluating non-thermal techniques for pulse starch modification is critical. This review aims to thoroughly assess these non-thermal techniques and their combinations, offering valuable insights for researchers and the food industry. By maximizing the potential of pulse starches in innovative food applications, it provides a comprehensive guide for effective non-thermal methods that add value and align with sustainable practices.

Rheological and gelling properties of atmospheric pressure cold plasma treated finger millet (Eleusine coracana) starch

Interest in exploring alternative starch sources like finger millet is rising due to wide starch applications. However, native starch often lacks desired qualities, including rheological properties. Modification is thus necessary for specific end uses. Plasma treatment as a greener and sustainable method for starch modification was therefore, studied for its ability to impact rheological properties of finger millet starch (FMS). Considerable changes in the rheological properties on FMS was noted, a significant decrease and increase (p < 0.05) in the peak viscosity (from 3.35 to 0.553 Pa.s) and paste clarity respectively was observed, indicating occurrence of depolymerization. However, intermediate plasma-treated samples (200 V) observed a decrease in paste clarity attributed to aggregate formation and cross-linking. Cross-linking was also confirmed by findings of frequency sweep where a continuous decrease in G' values of plasma treated FMS gel was interrupted by sudden increase. Despite depolymerization causing alteration of rheological behaviour such as decrease in shear thinning properties, gel strength observed a contradictory increase. This was attributed to incorporation of functional group and absence of shear responsible for network formation giving higher gel strength to FMS gels. This is elaborated in detail in the study. The study thus concluded that cold plasma significantly impacted all the rheological properties of the FMS and hence can prove to be beneficial for modification of starch rheological parameters.

Cold plasma: Unveiling its impact on hydration, rheology, nutritional, and anti-nutritional properties in food materials - An overview

Non-thermal technologies, primarily employed for microbial inactivation and quality preservation in foods, have seen a surge in interest, with non-thermal plasma garnering particular attention. Cold plasma exhibits promising outcomes, including enhanced germination, improved functional and rheological properties, and microorganism destruction. This has sparked increased exploration across various domains, notably in hydration and rheological properties for creating new products. This review underscores the manifold benefits of applying cold plasma to diverse food materials, such as cereal and millet flours, and gums. Notable improvements encompass enhanced functionality, modified color parameters, altered rheological properties, and reduced anti-nutritional factors. The review delves into mechanisms like starch granule fragmentation, elucidating how these processes enhance the physical and structural properties of food materials. While promising for high-quality food development, overcoming challenges in scaling up production and addressing legal issues is essential for the technology's commercialization.

The application of starch-based edible film in food preservation: a comprehensive review

Using renewable resources for food packaging not only helps reduce our dependence on fossil fuels but also minimizes the environmental impact associated with traditional plastics. Starch has been a hot topic in the field of current research because of its low cost, wide source and good film forming property. However, a comprehensive review in this field is still lacking. Starch-based films offer a promising alternative for sustainable packaging in the food industry. The present paper covers various aspects such as raw material sources, modification methods, and film formation mechanisms. Understanding the physicochemical properties and potential commercial applications is crucial for bridging the gap between research and practical implementation. Finally, the application of starch-based films in the food industry is discussed in detail. Different modifications of starch can improve the mechanical and barrier properties of the films. The addition of active substances to starch-based films can endow them with more functions. Therefore, these factors should be better investigated and optimized in future studies to improve the physicochemical properties and functionality of starch-based films. In summary, this review provides comprehensive information and the latest research progress of starch-based films in the food industry.

Understanding the atmospheric cold plasma-induced modification of finger millet (Eleusine coracana) starch and its related mechanisms

This research was conducted to evaluate the effects of cold plasma (CP) on finger millet starch (FMS). FMS was exposed to partially ionized gas at varying voltages (170, 200, and 230 Volt) for varied time (10, 20, and 30 mins). The impact of treatment was studied using physico-chemical, and functional properties, and the mechanisms of starch modification occurring were stated. A significant reduction in the degree of polymerization was noticed based on parameters like reducing sugar, amylose content, solubility, and molecular weight. However, in certain voltage and time combinations, crosslinking was also confirmed by analysis such as XRD, FTIR, DSC, etc. The properties of starch were altered such as remarkable increase in water solubility by 6.7 times for highest voltage and longest time (230 V/30 min) was registered. NMR data suggested valuable findings- oxidation of OH group at C6 position of starch led to formation of carbonyl group followed by carboxyl group. NMR also showed a decrease in OH protons confirming crosslinking and hence all these analyses helped to conclude findings about the quality changes using CP. It was observed that the highest voltage and considerably longer exposure time of 20 and 30 min induced significant changes in the FMS.

Dielectric barrier discharge cold plasma modifies the multiscale structure and functional properties of banana starch

Banana starch has attracted significant attention due to its abundant content of resistant starch. This study aims to compare the multiscale structure and functional properties of banana starch obtained from five cultivated varieties and investigate the impact of dielectric barrier discharge cold plasma (DBD) treatment on these starch characteristics. All five types of natural banana starch exhibited an elliptical and irregular shape, conforming to the CB crystal structure, with a bimodal distribution of branch chain lengths. The resistant starch content ranged from 88.9 % to 94.1 %. Variations in the amylose content, amylopectin branch chain length distribution, and structural characteristics resulted in differences in properties such as gelatinization behavior and sensitivity to DBD treatment. The DBD treatment inflicted surface damage on starch granules, reduced the amylose content, shortened the amylopectin branch chain length, and changed the relative crystallinity to varying degrees. The DBD treatment significantly increased starch solubility and light transmittance. Simultaneously, it resulted in a noteworthy decrease in peak viscosity and gelatinization enthalpy of starch paste. The in vitro digestibility test showed that 76.2 %-86.5 % of resistant starch was retained after DBD treatment. The DBD treatment renders banana starch with reduced viscosity, increased paste transparency, enhanced solubility, and broadens its potential application.

The effect of cold atmospheric plasma pretreatment on oil absorption, acrylamide content and sensory characteristics of deep-fried potato strips

This study investigated the impact of 60 kV Cold Atmospheric Plasma (CAP) pretreatment for varying durations (5, 10, and 15 min) on potato strip characteristics before and after frying, emphasizing oil uptake, acrylamide formation. Potato samples treated with cap showed significantly better physicochemical characteristics. Scanning electron microscopy revealed deformation of cell wall due to CAP treatment. Fourier-transform infrared spectroscopy indicated structural changes, while X-ray diffraction analysis suggested that starch remained amorphous state in CAP-pretreated samples. Post-frying, CAP-treated potato strips exhibited altered oil distribution with reduced absorption, possibly due to microstructural changes. CAP substantially reduced acrylamide formation during frying by degrading asparagine and inactivating amylase. CAP affected strip color, with increased brightness and decreased redness and yellowness after 14 days. Sensory evaluation showed no significant difference, with prolonged CAP-treated strips receiving higher overall acceptability scores. These findings highlight CAP as a non-thermal technology to enhance fried potato product quality and safety.

Effect of Intermittent Low-Pressure Radiofrequency Helium Cold Plasma Treatments on Rice Gelatinization, Fatty Acid, and Hygroscopicity

To establish the safe and reproducible effects of cold plasma (CP) technology on food products, this study evaluated the gelatinization parameters, fatty acid profile, and hygroscopic properties of rice grains repeatedly treated with low-pressure radiofrequency (RF) helium CP (13.56 MHz, 140 Pa, 120 W-20s, 0-4 times, and 300 g sample). Compared with the untreated (zero times) sample, with an increase in CP treatment times from one to four on rice, the water contact angle and cooking time decreased, while the water absorption rate and freshness index increased, and the pH value remained unchanged. CP repeating treatments essentially had no effect on the gelatinization enthalpy, but significantly increased the peak temperature of gelatinization. From the pasting profile of rice that has been repeatedly CP treated, the peak, breakdown, and setback viscosities in flour paste decreased. CP repeating treatments on rice did not change the short-range molecular order of starch. Compared with the untreated sample, the first helium CP treatment maintained the content of C18:1n9c, C18:2n6c, and C18:3n3, but the second to fourth CP treatment significantly decreased contents of these fatty acids (FAs) as the C18:0 content increased. The first three CP treatments can increase the water and sucrose solvent retention capacity in rice flours. CP repeatedly treated rice first exhibits the similar monolayer water content and solid surface area of water sorption. Principal component analysis shows that contact angle, pasting parameters, and fatty acid profile in milled rice are quite sensitive to CP treatment. Results support that the effect of low-pressure RF 120W helium CP treatment 20 s on rice grains is perdurable, and the improvement of CP intermittent treatments on rice cooking and pasting properties is an added benefit, and the hygroscopic properties of rice was kept.

Multi-scale structural disruption induced by radio frequency air cold plasma accelerates enzymatic hydrolysis/ hydroxypropylation of tapioca starch

This study investigated the effects of radio frequency air cold plasma (RFACP) pretreatment on the multi-scale structures, physicochemical properties, enzymatic hydrolysis, and hydroxypropylation of tapioca starch. The results showed that cold plasma (CP) made starch granules rough on the surface and disrupted long- and short-range ordered structures, reducing relative crystallinity from 43.8 % to 37.4 % and R1047/1022 value from 0.992 to 0.934. Meanwhile, the starch molecules were depolymerized and oxidized by CP, reducing weight-average molecular weight from 9.64 × 107 to 2.17 × 107 g/mol, while increasing carbonyl and carboxyl groups by up to 118 % and 53 %. Additionally, CP-treated starches exhibited higher solubility and swelling power, along with lower gelatinization enthalpy. Short-time CP pretreatment (10 min) promoted the hydroxypropylation of starch and increased the molar substitution (0.081-0.112). Also, CP pretreatment accelerated enzymatic hydrolysis of starch, as indicated by the increase in hydrolysis rate (1.846 × 10-3-2.033 × 10-3 min-1) and degree of hydrolysis (51.45 % - 59.92 %). Overall, the multi-scale structural disruption induced by CP treatment facilitated the accessibility of enzymes/chemical reagents into starch granules and glucan chains. This study suggested that RFACP could be used for starch pretreatment to increase production efficiency in modified starch production, as well as in brewing and fermentation industries.

Evaluation of dual modification by high hydrostatic pressure and annealing on the physicochemical properties of bean starch

This study investigated the physical modifications by high hydrostatic pressure (HHP) at 600 MPa for 30 min/30 °C, annealing (AN) at 50 °C/24 h and the combination of both (HHP + AN and AN + HHP) applied to yellow bean starch to verify changes in morphology, X-ray diffraction, molecular order, thermal properties and pasting properties of native (NS) and modified starches. Morphological analysis showed loss of sphericity and increase in diameter with the appearance of pores on the surface after application of treatments. The AN starch showed lower values of syneresis, degree of double helix (DD), order (DO), and viscosity of the paste obtained by RVA. It exhibited a Vh-type classification with the appearance of the amylose-lipid complex. However, the gelatinization temperatures, as well as the enthalpy of gelatinization, were significantly higher. On the other hand, the starch treated with HHP showed a higher Setback (SB) value. The greatest modifications were found for the starches subjected to the combined treatments (AN + HHP) and (HHP + AN), where the order of the treatments was significant for the morpho-structural changes of yellow bean starch. According to the micrographs, the surface aspect was altered, with AN + HHP showing greater irregularities and flat yet irregular faces, as well as a larger granule diameter (147.05). The X-ray diffractogram showed a reduction in crystallinity from 28.14 % (NS) to 18.09 % (AN + HHP) and classified the starch as type "A". The double modification (HHP + AN and AN + HHP) reduced the gelatinization temperature and the enthalpy of gelatinization but had no effect on the bands of the FT-IR spectrum. There was only a reduction in the degree of order and the double helix. Finally, the treatment with AN + HHP is more effective as the gelatinization with AN facilitates the application of HHP. Both methods used are classified as physical (thermal and non-thermal), aiming to minimize environmental impacts and achieve faster and safer morpho-structural modification without leaving chemical residues in the products.

Atmospheric pressure pin-to-plate cold plasma effect on physicochemical, functional, pasting, thermal, and structural characteristics of proso-millet starch

The present work aimed to study the influence of atmospheric pressure pin-to-plate cold plasma on the physicochemical (pH, moisture, and amylose content), functional (water & oil binding capacity, solubility & swelling power, paste clarity on storage, pasting), powder flow, thermal and structural (FTIR, XRD, and SEM) characteristics at an input voltage of 170-230 V for 5-15 min. The starch surface modification by cold plasma was seen in the SEM images which cause the surge in WBC (1.54 g/g to 1.93 g/g), OBC (2.22 g/g to 2.79 g/g), solubility (3.05-5.38% at 70 °C; 37.11-52.98% at 90 °C) and swelling power (5.39-7.83% at 70 °C; 25.67-35.33% at 90 °C) of starch. Reduction in the amylose content (27.82% to 25.07%) via plasma-induced depolymerization resists the retrogradation tendency, thereby increasing the paste clarity (up to ̴ 39%) during the 5 days of refrigerated storage. However, the paste viscosity is reduced after cold plasma treatment yielding low-strength starch pastes. The relative crystallinity of starch increased (37.35% to 45.36%) by the plasma-induced fragmented starch granules which would aggregate and broaden the gelatinization temperature, but these starch fragments reduced the gelatinization enthalpy. The fundamental starch structure is conserved as seen in FTIR spectra. Thus, cold plasma aids in the production of soluble, low-viscous, stable, and clear paste-forming depolymerized proso-millet starch.

Enhanced properties of non-starch polysaccharide and protein hydrocolloids through plasma treatment: A review

Hydrocolloids are important ingredients in food formulations and their modification can lead to novel ingredients with unique functionalities beyond their nutritional value. Cold plasma is a promising technology for the modification of food biopolymers due to its non-toxic and eco-friendly nature. This review discusses the recent published studies on the effects of cold plasma treatment on non-starch hydrocolloids and their derivatives. It covers the common phenomena that occur during plasma treatment, including ionization, etching effect, surface modification, and ashing effect, and how they contribute to various changes in food biopolymers. The effects of plasma treatment on important properties such as color, crystallinity, chemical structure, rheological behavior, and thermal properties of non-starch hydrocolloids and their derivatives are also discussed. In addition, this review highlights the potential of cold plasma treatment to enhance the functionality of food biopolymers and improve the quality of food products. The mechanisms underlying the effects of plasma treatment on food biopolymers, which can be useful for future research in this area, are also discussed. Overall, this review paper presents a comprehensive overview of the current knowledge in the field of cold plasma treatment of non-starch hydrocolloids and their derivatives and highlights the areas that require further investigation.

A review of green methods used in starch-polyphenol interactions: physicochemical and digestion aspects

The interactions of starch with lipids, proteins, and other major food components during food processing are inevitable. These interactions could result in the formation of V-type or non-V-type complexes of starch. The starch-lipid complexes have been intensively studied for over five decades, however, the complexes of starch and polyphenols are relatively less studied and are the subject of recent interest. The interactions of starch with polyphenols can affect the physicochemical properties and its digestibility. The literature has highlighted several green methods such as ultrasound, microwave, high pressure, extrusion, ball-milling, cold plasma etc., to assist interactions of starch with polyphenols. However, comprehensive information on green methods to induce starch-polyphenol interactions is still scarce. Therefore, in light of the importance and potential of starch-polyphenol complexes in developing functional foods with low digestion, this review has summarized the novel green methods employed in interactions of starch with flavonoids, phenolic acids and tannins. It has been speculated that flavonoids, phenolic acids, and tannins, among other types of polyphenols, may have anti-digestive activities and are also revealed for their interaction with starch to form either an inclusion or non-inclusion complex. Further information on the effects of these interactions on physicochemical parameters to understand the chemistry and structure of the complexes is also provided.

Hierarchical structural modification of starch via non-thermal plasma: A state-of-the-art review

The hierarchical architecture of natural and processed starches with different surface and internal structures determines their final physicochemical properties. However, the oriented control of starch structure presents a significant challenge, and non-thermal plasma (cold plasma, CP) has gradually been used to design and tailor starch macromolecules, though without clear illustration. In this review, the multi-scale structure (i.e., chain-length distribution, crystal structure, lamellar structure, and particle surface) of starch is summarized by CP treatment. The plasma type, mode, medium gas and mechanism are also illustrated, as well as their sustainable food applications, such as in food taste, safety, and packaging. The effects of CP on the chain-length distribution, lamellar structure, amorphous zone, and particle surface/core of starch includes irregularity due to the complex of CP types, action modes, and reactive conditions. CP-induced chain breaks lead to short-chain distributions in starch, but this rule is no longer useful when CP is combined with other physical treatments. The degree but not type of starch crystals is indirectly influenced by CP through attacking the amorphous region. Furthermore, the CP-induced surface corrosion and channel disintegration of starch cause changes in functional properties for starch-related applications.

Effects of pin-to-plate atmospheric cold plasma for modification of pearl millet (Pennisetum glaucum) starch

The present study was done to analyze the effect of atmospheric pressure non-thermal pin-to-plate plasma at a range of different voltages (170, 200, and 230V) at different time intervals (10, 20, and 30 mins) on under-utilized pearl millet starch. The untreated and treated starches were analyzed for amylose content, pH, carbonyl, and carboxyl group, reducing sugar, turbidity, water, and oil binding property, pasting property, DSC, FTIR, XRD, and molecular weight. As cold plasma contains highly reactive species and free radicals, it is expected to cause noticeable modifications in the attributes of treated starch. There has been a significant reduction (p < 0.05) in turbidity value by 38.97% and pH value of starch from 6.49 to 4.05. Plasma-treated samples produced clearer pastes with higher stability over storage time. Cold plasma treatment also led to an increase in the ζ potential. However, there has been no significant change in the water activity and oil-binding capacity of the starch. Reducing sugar content, average molecular weight, degree of polymerization, pasting property, XRD, and FTIR data confirmed that cross-linking takes place in samples treated at lower voltages and lesser time followed by depolymerization occurring in harshly treated plasma samples. The study thus points out the possible use of cold plasma for starch modification to produce starches with altered properties.

Loquat seed starch - Emerging source of non-conventional starch: Structure, properties, and novel applications

Recently, non-conventional sources of starch have attracted attention due to their potential to provide cost-effective alternatives to traditional starch. Among non-conventional starches, loquat (Eriobotrya japonica) seed starch is an emerging source of starch consisting of the amount of starch (nearly 20 %). Due to its unique structure, functional properties, and novel applications, it could be utilized as a potential ingredient. Interestingly, this starch has similar properties as commercial starches including high amylose content, small granule size, and high viscosity and heat stability, making it an attractive option for various food applications. Therefore, this review mainly covers the fundamental understanding of the valorization of loquat seeds by extracting the starch using different isolation methods, with preferable structural, morphological, and functional properties. Different isolation and modification methods (wet milling, acid, neutral and alkaline) are effectively used to obtain higher amounts of starch are revealed. Moreover, insight into various analytical techniques including scanning electron microscopy, differential scanning calorimetry, and X-ray diffraction used to characterize the molecular structure of the starch are discussed. In addition, the effect of shear rate and temperature on rheological attributes with solubility index, swelling power, and color is revealed. Besides, this starch contains bioactive compounds that have shown a positive impact on the enhancement of the shelf-life of the fruits. Overall, loquat seed starches have the potential to provide sustainable and cost-effective alternatives to traditional starch sources and can lead to novel applications in the food industry. Further research is needed to optimize processing techniques and develop value-added products that can be produced at a large scale. However, there is relatively limited published scientific evidence on the structural and morphological characteristics of loquat seed starch. Thus, in this review, we focused on different isolation techniques of loquat seed starch, its structural and functional characteristics, along with potential applications.

Research Progress of Quinoa Seeds (Chenopodium quinoa Wild.): Nutritional Components, Technological Treatment, and Application

Quinoa (Chenopodium quinoa Wild.) is a pseudo-grain that belongs to the amaranth family and has gained attention due to its exceptional nutritional properties. Compared to other grains, quinoa has a higher protein content, a more balanced amino acid profile, unique starch features, higher levels of dietary fiber, and a variety of phytochemicals. In this review, the physicochemical and functional properties of the major nutritional components in quinoa are summarized and compared to those of other grains. Our review also highlights the technological approaches used to improve the quality of quinoa-based products. The challenges of formulating quinoa into food products are addressed, and strategies for overcoming these challenges through technological innovation are discussed. This review also provides examples of common applications of quinoa seeds. Overall, the review underscores the potential benefits of incorporating quinoa into the diet and the importance of developing innovative approaches to enhance the nutritional quality and functionality of quinoa-based products.

Cold plasma as a pre-treatment for processing improvement in food: A review

Thermal processes can be very damaging to the nutritional and sensory quality of foods. Non-thermal technologies have been applied to reduce the impact of heat on food, reducing processing time and increasing its efficiency. Among many non-thermal technologies, cold plasma is an emerging technology with several potential applications in food processing. This technique can be used to preserve and sanitize food products, and act as a pre-treatment for drying, extraction, cooking, curing, and hydrogenation of foods. Furthermore, the reacting plasma species formed during the plasma application can change positively the sensory and nutritional aspects of foods. The aim of this review is to analyze the main findings on the application of cold plasma as a pre-treatment technology to improve food processing. In its current maturity stage, the cold plasma technology is suitable for reducing drying time, increasing extraction efficiency, as well as curing meats. This technology can convert unsaturated into saturated fats, without forming trans isomers, which can be an alternative to healthier foods. Although many advantages come from cold plasma applications, this technology still has several challenges, such as the scaling up, especially in increasing productivity and treating foods with large formats. Optimization and control of the effects of plasma on nutritional and sensory quality are still under investigation. Further improvement of the technology will come with a higher knowledge of the effects of plasma on the different chemical groups present in foods, and with the development of bigger or more powerful plasma systems.

Degradation of deoxynivalenol in wheat by double dielectric barrier discharge cold plasma: identification and pathway of degradation products

BACKGROUND

Deoxynivalenol (DON) produced during the onset of fusarium head blight not only affects the quality and safety of wheat but also causes serious harm to human and livestock health. However, due to the high stability of DON, it is difficult to eliminate it or reduce it naturally after it has been produced. Cold plasma technology is a non-thermophysical processing technology that has been widely used for microbial inactivation and mycotoxin degradation. In this study, the degradation efficiency of double dielectric barrier discharge (DDBD) cold plasma on DON in aqueous solution and wheat was studied; the structures of degradation products of DON and its pathway were clarified, and the effect of DDBD plasma on wheat quality was evaluated.

RESULTS

Double dielectric barrier discharge cold plasma was used for efficient degradation of DON (0.5 ~ 5 μgmL^-1) solution and achieved a degradation rate of 98.94% within 25 min under the optimal conditions (voltage 100 V, frequency 200 Hz, duty cycle 80%). Furthermore, 10 degradation products (C₁₅ H₂₄ O₅ , C₁₅ H₂₂ O₆ , C₁₅ H₂₂ O₉ , C₁₆ H₂₂ O₇ , C₁₅ H₂₀ O₇ , C₁₅ H₂₀ O₉ , C₁₅ H₁₈ O₈ , C₁₅ H₂₂ O₅ , C₁₆ H₂₄ O₅ , and C₁₅ H₁₈ O₉ ) were identified by ultra-performance liquid chromatography-time of flight-mass spectrometry (UPLC-TOF-MS/MS) combined with Metabolitepilot and Peakview software. The degradation pathway of DON was obtained based on the chemical structures and accurate mass of these products. The DON degradation rate of 61% in wheat was achieved after treatment for 15 min, which slightly affects the moisture content, proteins, and wheat starch.

CONCLUSION

Applying DDBD to wheat could effectively reduce the level of DON contamination, which provides a theoretical basis for applying cold plasma to the degradation of DON in wheat. © 2022 Society of Chemical Industry.

Comparison of Physicochemical Properties of Silver and Gold Nanocomposites Based on Potato Starch in Distilled and Cold Plasma-Treated Water

Nanometal-containing biocomposites find wide use in many industries and fields of science. The physicochemical properties of these materials depend on the character of the polymer, the size and shape of the metallic nanoparticles, and the interactions between the biopolymer and the nanoparticles. The aim of the work was to synthesise and study the effect of plasma-treated water on the properties of the obtained metallic nanoparticles as well as the physicochemical and functional properties of nanocomposites based on potato starch. The metallic nanoparticles were synthesised within a starch paste made in distilled water and in distilled water exposed to low-temperature, low-pressure plasma. The materials produced were characterised in terms of their physicochemical properties. Studies have shown that gold and silver nanoparticles were successfully obtained in a matrix of potato starch in distilled water and plasma water. SEM (Scanning Electron Microscopy) images and UV-Vis spectra confirmed the presence of nanosilver and nanosilver in the obtained composites. On the basis of microscopic images, the size of nanoparticles was estimated in the range from 5 to 20 nm for nanoAg and from 15 to 40 nm for nanoAu. The analysis of FTIR-ATR spectra showed that the type of water used and the synthesis of gold and silver nanoparticles did not lead to changes in the chemical structure of potato starch. DLS analysis showed that the nanoAg obtained in the plasma water-based starch matrix were smaller than the Ag particles obtained using distilled water. Colour analysis showed that the nanocomposites without nanometals were colourless, while those containing nanoAg were yellow, while those with nanoAu were dark purple. This work shows the possibility of using plasma water in the synthesis of nanometals using potato starch, which is a very promising polysaccharide in terms of many potential applications.

Non-Thermal Plasma Decontamination Using a Multi-Hollow Surface Dielectric Barrier Discharge: Impact of Food Matrix Composition on Bactericidal Efficacy

The non-thermal plasma (NTP) treatment of food products as an alternative for thermal processing has been investigated over the last few years. This quasi-neutral gas contains a wide variety of reactive oxygen and nitrogen species (RONS), which could be lethal for bacterial cells present in the product. However, apart from only targeting bacteria, the RONS will also interact with components present in the food matrix. Therefore, these food components will protect the microorganisms, and the NTP treatment efficiency will decrease. This effect was investigated by supplementing a plain agar medium with various representative food matrix components. After inoculation with Escherichia coli O157:H7 (STEC) MB3885, the plates were treated for 30 s by a multi-hollow surface dielectric barrier discharge (MSDBD) generated in either dry air or air at 75% humidity, at constant power (25.7 ± 1.7 W). Subsequently, the survival of the cells was quantified. It has been found that the addition of casein hydrolysate (7.1 ± 0.2 m%), starch (2.0 m%), or soybean oil (4.6 m%) decreased the inactivation effect significantly. Food products containing these biomolecules might therefore need a more severe NTP treatment. Additionally, with increasing humidity of the plasma input gas, ozone levels decreased, and the bactericidal effect was generally less pronounced.

Porous corn starch obtained from combined cold plasma and enzymatic hydrolysis: Microstructure and physicochemical properties

The combined effect of cold plasma treatment and enzymatic hydrolysis was investigated on the physicochemical and microstructural properties of porous corn starch. Scanning electron microscopy (SEM) images depicted that the combined treatment led to the creation of deeper pores on the surface of starch granules. The combined treatment indicated the highest swelling power (19.49 g/g), solubility (10.08 %), specific surface area (2.97 m²/g) and total pore volume (10.47 cm³/g). According to the X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), and differential scanning calorimetry (DSC), the combined treatment, compared with the enzymatic hydrolysis, decreased the starch crystallinity, the order of the double-helix structure, and the starch gelatinization enthalpy. The rapid visco analyzer (RVA) pasting profile revealed that the combined treatment elevated the breakdown and setback viscosities. This study indicated that cold plasma pretreatment, as a green non-thermal technology, facilitated the performance of enzymes, resulting in the production of a porous starch with a higher absorption capacity.

Thermal properties of different types of starch: A review

Starch is present in high amount in various cereals, fruits and roots & tubers which finds major application in industry. Commercially, starch is rarely consumed or processed in its native form, thus modification of starch is widely used method for increasing its application and process stability. Due to the high demand for starch in industrial applications, researchers were driven to hunt for new sources of starch, including modification of starch through green processing. Thermal properties are significant reference parameters for evaluating the quality of starch when it comes to cooking and processing. Modification of starches affects the thermal properties, which are widely studied using Differential scanning calorimeter or Thermogravimetric analysis. It could lead to a better understanding of starch's thermal properties including factors influencing and expand its commercial applications as a thickener, extender, fat replacer, etc. in more depth. Therefore, the review presents the classification of starches, factors influencing the thermal properties, measurement methods and thermal properties of starch in its native and modified form. Further, this review concludes that extensive research on the thermal properties of new sources of starch, as well as modified starch, is required to boost thermal stability and extend industrial applications.

Impacts of Cold Plasma Technology on Sensory, Nutritional and Safety Quality of Food: A Review

As an emerging non-thermal food processing technology, cold plasma (CP) technology has been widely applied in food preservation due to its high efficiency, greenness and lack of chemical residues. Recent studies have indicated that CP technology also has an impressing effect on improving food quality. This review summarized the impact of CP on the functional composition and quality characteristics of various food products. CP technology can prevent the growth of spoilage microorganisms while maintaining the physical and chemical properties of the food. It can maintain the color, flavor and texture of food. CP can cause changes in protein structure and function, lipid oxidation, vitamin and monosaccharide degradation, starch modification and the retention of phenolic substances. Additionally, it also degrades allergens and toxins in food. In this review, the effects of CP on organoleptic properties, nutrient content, safety performance for food and the factors that cause these changes were concluded. This review also highlights the current application limitations and future development directions of CP technology in the food industry. This review enables us to more comprehensively understand the impacts of CP technology on food quality and promotes the healthy application of CP technology in the food industry.

Effect of plasma activated water on Escherichia coli disinfection and quality of kale and spinach

Plasma activated water (PAW) is one of the promising technologies for fresh food disinfection. In this study, PAW was generated by activating water under nonthermal plasma for 10, 20, 30, 45 and 60 min. The effectiveness of Escherichia coli inactivation by PAW treatment on kale and spinach samples was assessed. The differences between kale and spinach samples in terms of the product quality and nutritional characteristics upon PAW treatment was also investigated. Further, changes in leaf structure and surface morphology upon PAW treatment was also evaluated through FTIR cuticle analysis and SEM imaging of leaf surfaces. Results showed that, around 6 log CFU/g reduction in E. coli population was observed in PAW-45 min treatment. However, PAW treatment significantly reduced the total chlorophyll content in both kale and spinach. The total phenolic content, flavonoid content and ascorbic content were altered according to the PAW activation time. Further, kale and spinach behaved differently in terms of antioxidant activity and membrane electrolytic leakage values upon PAW treatment. Clear changes in the cuticular layer and the surface morphological characteristics of the leaf samples were observed after PAW which could be the reason for the significant differences between kale and spinach characteristics in response to PAW treatments.

Cold plasma: a promising technology for improving the rheological characteristics of food

At the beginning of the 21st century, many consumers show interest in purchasing safe, healthy, and nutritious foods. The intent requirement of end-users and many food product manufacturers are trying to feature a new processing technique for the healthy food supply. The non-thermal nature of cold plasma treatment is one of the leading breakthrough technologies for several food processing applications. The beneficial response of cold plasma processing on food quality characteristics is widely accepted as a substitution technique for new food manufacturing practices. This review aims to elaborate and offer crispy innovative ideas on cold plasma application in various food processing channels. It highlights the scientific approaches on the principle of generation and mechanism of cold plasma treatment on rheological properties of foods. It provides an overview of the behavior of cold plasma in terms of viscosity, crystallization, gelatinization, shear stress, and shear rate. Research reports highlighted that the cold plasma treated samples demonstrated a pseudoplastic behavior. The published literatures indicated that the cold plasma is a potential technology for modification of native starch to obtain desirable rheological properties. The adaptability and environmentally friendly nature of non-thermal cold plasma processing provide exclusive advantages compared to the traditional processing technique.

Dielectric barrier discharge cold plasma combined with cross-linking: An innovative way to modify the multi-scale structure and physicochemical properties of corn starch

Cold plasma is a low-cost, simple and green method for starch modification. In the present study, the impact of corn starch modification by cold plasma (CP, 1, 3 and 9 min), sodium trimetaphosphate/sodium tripolyphosphate (CL, 1 %, 5 % and 10 %) and their combination were investigated. CP-pretreatment had enhancement of phosphorus content and substitution degree. Neither CP nor CL destroyed the starch granules morphology. Instead, CP induced more short-chain to better rearrange the starch during the crosslinking process, which improved the efficiency of the crosslinker in the subsequent crosslinking process. Therefore, compared with CL or CP, the thermal transition temperatures increased after CP pretreatment, while the amylose content, relative crystallinity, swelling power, and △H decreased. Meanwhile, CP-pretreatment changed the internal structure of the CL-starch so that it showed the lowest enzymatic digestibility. CP pretreatment provides a promising way to improve cross-linked starch's structure, properties, and efficiency.