An electrochemical sensor for determination of nitrite based on Au nanoparticles decorated MoS2 nanosheets

Rapid colorimetric assay based on the oxidation of 2,2-azino-bis(3-ethylbenzothiazoline)-6-sulfonic acid-diammonium salt for nitrite detection in meat products

This work developed a rapid colorimetric method for nitrite detection in meat products. The detection was based on the reaction of nitrite with 60 mM HCl to produce radicals which further oxidized ABTS (50 µM) to form a water-soluble blue-green product (ABTS•+). The absorbance was measured at a maximum absorption wavelength of 412.5 nm. Parameters such as concentration of HCl, concentration of ABTS and reaction time were evaluated. The absorbance was linearly proportional to the concentration of nitrite (0.1-20 µM) with the limit of detection of 0.34 µM. The proposed method was a time-saving assay since it required only 2 min to complete one measurement. There was no effect of the interference produced by other ions. The assay was robust with 2.5%RSD (n = 50). In meat product samples, high accuracy was observed with the recoveries between 100 ± 2.2% and 105 ± 3.7%. The amount of nitrite in meat products detected by the ABTS method was found in the range of 5.41 - 7.62 mg/kg. The conventional Griess method was applied to determine nitrite in the same meat products. There was no statistically significant difference between the two methods (P = 0.05).

Gold Nanomaterials and their Composites as Electrochemical Sensing Platforms for Nitrite Detection

Nitrite is one of the abundant toxic components existing in the environment and is likely to have a great potential to affect human health badly. For that reason, it has become crucial to build a reliable nitrite detection method. In recent years, several nitrite monitoring systems have been proposed. Compared with traditional analytical strategies, the electrochemical approach has a bunch of advantages, including low cost, rapid response, easy operation, simplicity, etc. In this case, noble metal nanomaterials, especially Au-based nanomaterials, have attracted attention in electrode modification because of higher catalytic activity, facile mass transfer, and broad active area for determining nitrite. This review is based on the state-of-the-art, which includes a variety of nanomaterials that have been coupled with AuNPs for the creation of nanocomposites, and the construction as well as development of electrochemical sensors for nitrite detection over the last few years (2016-2022). A background study on synthesizing different morphological AuNPs and nanocomposites has also been introduced. The fabrication methods and sensing capabilities of modified electrodes are given special consideration.

Voltammetric sensor based on glassy carbon electrode modified with hierarchical porous carbon, silver sulfide nanoparticles and fullerene for electrochemical monitoring of nitrite in food samples

This paper reports the development of a voltammetric sensor using glassy carbon electrode based on hierarchical porous carbon (HPC) with silver sulfide nanoparticles (Ag₂SNP), Nafion and fullerene (C₆₀) for the determination of nitrite in foods. Raman spectroscopy, scanning electron microscopy, transmission electron microscopy and energy-dispersive X-ray were used to characterize the morphology and composition of the materials. The use of HPC and C₆₀ in the construction of the electrode contributed toward the enlargement of the specific surface area and the improvement of the electrochemical performance of the device. The electrochemical behavior of nitrite in different electrodes was evaluated by cyclic voltammetry in the potential range of 0.4 - 1 V. Using the optimal conditions, a linear response ranges of 4.0- 148 μmol L^-1, a limit of detection of 0.09 μmol L^-1 and a sensitivity of 0.05 μAμmol L^-1 cm^-2 were obtained. The results showed that the proposed method can selectively detect nitrite in the presence of other compounds without interference and with good stability. The proposed method was successfully applied for the detection of nitrite in food samples where it demonstrated a good degree of accuracy and satisfactory efficiency.

Enhanced Nitrite Detection by a Carbon Screen Printed Electrode Modified with Photochemically-Made AuNPs

Excessive nitrite amounts harm the environment and put public health at high risk. Therefore, accurate and sensitive detection of nitrite in surface and groundwater is mandatory for mitigating its adverse effects. Herein, a highly sensitive electrochemical sensor based on carbon screen-printed electrodes (CSPE) surface-modified with photochemically-made gold nanoparticles (AuNPs, ~12 nm) is proposed for nitrite detection. Scanning electron microscopy, cyclic voltammetry, and electrochemical impedance spectroscopy show that AuNPs uniformly coat the CSPE, increase its surface area, and contribute to oxidizing nitrite to much lower potential (+0.5 V vs. Ag/AgCl) and faster rate. Under optimized differential pulse voltammetry conditions, the CSPE/AuNPs-PEI electrode responds linearly (R2 > 0.99) to nitrite within a wide concentration range (0.01–4.0 µM), showing a sensitivity of 0.85 µA·µM−1·cm−2 and limit of detection as low as 2.5 nM. The CSPE/AuNPs-PEI electrode successfully detects nitrite in tap water and canned water of olives, showing no influence of those matrices. In addition, the electrode’s response is highly reproducible since a relative standard deviation lower than 10% is observed when the same electrode is operated in five consecutive measurements or when electrodes of different fabrication batches are evaluated.

Cytochrome c-multiwalled carbon nanotube and cobalt metal organic framework/gold nanoparticle immobilized electrochemical biosensor for nitrite detection

Based on cytochrome c-multiwalled carbon nanotubes (Cyt c-MWCNTs) and cobalt metal–organic frameworks/gold nanoparticles (Co-MOFs/AuNPs), an electrochemical biosensor was proposed for the detection of nitrite. Herein, Co-MOFs and AuNPs were immobilized on gold electrodes via surface layer assembly. Their advantages including large surface area and high conductivity provided an excellent platform for the immobilization of Cyt c-MWCNTs. Cyt c-MWCNTs were prepared via electrostatic adsorption and possessed good biocompatibility and superior electrocatalytic activity towards nitrite. Notably, MWCNTs and AuNPs could provide a good microenvironment for the electron transfer of Cyt c, which further significantly promoted the dispersion of MWCNTs. All of the above features led to outstanding electrochemical performance and achieved signal amplification for nitrite detection. Therefore, the biosensor displayed a linear range from 0.005 μmol L⁻¹ to 1000 μmol L⁻¹ with a detection limit of 0.0044 μmol L⁻¹ for nitrite detection. In addition, the designed biosensor exhibited excellent selectivity and could be applied in real samples.

Based on cytochrome c-multiwalled carbon nanotubes (Cyt c-MWCNTs) and cobalt metal organic frameworks/gold nanoparticles (Co-MOFs/AuNPs), an electrochemical biosensor was proposed for the detection of nitrite.

A highly sensitive poly(chrysoidine G)-gold nanoparticle composite based nitrite sensor for food safety applications

This work demonstrated the development of conducting poly(chrysoidine G) (PCG)-gold nanoparticle (AuNP)-modified fluorine-doped tin oxide (F : SnO₂, FTO) film-coated glass electrodes for the sensitive electrochemical detection of nitrite (NO₂^-). The homogeneously distributed PCG nanoparticle layer was deposited onto the FTO electrode by cyclic voltammetry sweeping. AuNPs were then anchored onto the PCG/FTO electrode by the chemical reduction of pre-adsorbed Au³⁺ ions. The as-prepared AuNP/PCG/FTO electrode exhibited excellent electrocatalytic activity for the oxidation of NO₂^- with high sensitivity (approximately 0.63 μA cm^-2μM^-1) and a low limit of detection (0.095 μM), which is relevant within the normal concentration range of NO₂^- in human bodily fluids. The AuNP/PCG/FTO sensor showed sufficient reproducibility, repeatability, low interference, and strong recovery for NO₂^- detection in food samples. These results indicate that the AuNP/PCG nanocomposites have immense potential for the electrochemical detection of other biologically important compounds.