Biomass derived graphene-like activated and non-activated porous carbon for advanced supercapacitors

Efficient removal of antibiotics from water resources is a public health priority: a critical assessment of the efficacy of some remediation strategies for antibiotics in water

This review discusses the fundamental principles and mechanism of antibiotic removal from water of some commonly applied treatment techniques including chlorination, ozonation, UV-irradiation, Fenton processes, photocatalysis, electrochemical-oxidation, plasma, biochar, anaerobicdigestion, activated carbon and nanomaterials. Some experimental shortfalls identified by researchers such as certain characteristics of degradation agent applied and the strategies explored to override the identified limitations are briefly discussed. Depending on interactions of a range of factors including the type of antibiotic compound, operational parameters applied such as pH, temperature and treatment time, among other factors, all reviewed techniques can eliminate or reduce the levels of antibiotic compounds in water to varying extents. Some of the reviewed techniques such as anaerobic digestion generally require longer treatment times (up to 360, 193 and 170 days, according to some studies), while others such as photocatalysis achieved degradation within short contact time (within a minimum of 30, but up to 60, 240, 300 and 1880 minutes, in some cases). For some treatment techniques such as ozonation and Fenton, it is apparent that subjecting compounds to longer treatment times may improve elimination efficiency, whereas for some other techniques such as nanotechnology, application of longer treatment time generally meant comparatively minimal elimination efficiency. Based on the findings of experimental studies summarized, it is apparent that operational parameters such as pH and treatment time, while critical, do not exert sole or primary influence on the elimination percentage(s) achieved. Elimination efficiency achieved rather seems to be due more to the force of a combination of several factors.

A leather-based electrolyte for all-in-one configured flexible supercapacitors

Leather based gel electrolytes were prepared from the top down method, and integrated flexible supercapacitors were developed by this method.

A high energy flexible symmetric supercapacitor fabricated using N-doped activated carbon derived from palm flowers

Nitrogen doped activated carbons of high surface area are synthesized using palm flower biomaterial by KOH activation followed by pyrolysis. The concentration of the activating agent KOH and carbonization temperature are found to be crucial to obtain high surface area activated carbon. The optimal concentration of KOH and carbonization temperature for the synthesis of activated carbon, respectively, are 2 M and 800 °C in the flow of nitrogen gas. The optimized conditions have been employed to further prepare nitrogen doped activated carbon (NAC) by varying the weight ratio of palm flowers to melamine. All activated carbons are characterized by powder XRD, BET analysis, RAMAN spectroscopy, HR-SEM analysis, HR-TEM analysis and FT-IR analysis. With 2 wt% nitrogen doping, the BET surface area and pore diameter of the NAC-2 sample are 1054 m2 g-1 and 1.9 nm, respectively. The electrochemical charge storage performance of the nitrogen doped activated carbons has been evaluated in an aqueous acidic electrolyte medium. The results indicate that among the nitrogen doped activated carbons, the NAC-2 sample exhibits the highest electrochemical capacitance of 296 F g-1 at 0.5 A g-1. The performance of the NAC-2 electrode is further tested in aqueous, ionic liquid and solid polymer electrolytes by assembling a symmetric capacitor for real time application. By employing an ionic liquid as the electrolyte, the device delivers an energy density of 8.6 Wh kg-1 and a power density of 38.9 W kg-1 in the voltage window of 1.5 V and at an operating current density of 0.1 A g-1. Interestingly, the NAC-2 electrode shows good cycling performance in the ionic liquid electrolyte (up to 50k cycles). Furthermore, the symmetric device in 0.1 M H2SO4/PVA solid state electrolyte shows excellent electrochemical stability under various bending angles, demonstrating its potential in flexible electronic devices.

Silica and graphene mediate arsenic detection in mature rice grain by a newly patterned current-volt aptasensor

Arsenic is a major global threat to the ecosystem. Here we describe a highly accurate sensing platform using silica nanoparticles/graphene at the surface of aluminum interdigitated electrodes (Al IDE), able to detect trace amounts of arsenic(III) in rice grain samples. The morphology and electrical properties of fabricated Al IDEs were characterized and standardized using AFM, and SEM with EDX analyses. Micrometer scale Al IDEs were fabricated with silicon, aluminum, and oxygen as primary elements. Validation of the bare Al IDE with electrolyte fouling was performed at different pH levels. The sensing surface was stable with no electrolyte fouling at pH 7. Each chemical modification step was monitored with current-volt measurement. The surface chemical bonds were characterized by fourier transform infrared spectroscopy (FTIR) and revealed different peaks when interacting with arsenic (1600-1000 cm^-1). Both silica nanoparticles and graphene presented a sensitive limit of detection as measured by slope calibration curves at 0.0000001 pg/ml, respectively. Further, linear regression was established using ΔI (A) = 3.86 E^-09 log (Arsenic concentration) [g/ml] + 8.67 E^-08 [A] for silica nanoparticles, whereas for graphene Y = 3.73 E^-09 (Arsenic concentration) [g/ml] + 8.52 E^-08 on the linear range of 0.0000001 pg/ml to 0.01 pg/ml. The R² for silica (0.96) and that of graphene (0.94) was close to the maximum (1). Modification with silica nanoparticles was highly stable. The potential use of silica nanoparticles in the detection of arsenic in rice grain extract can be attributed to their size and stability.

Present Status and Future Prospects of Jute in Nanotechnology: A Review

Nanotechnology has transformed the world with its diverse applications, ranging from industrial developments to impacting our daily lives. It has multiple applications throughout financial sectors and enables the development of facilitating scientific endeavors with extensive commercial potentials. Nanomaterials, especially the ones which have shown biomedical and other health-related properties, have added new dimensions to the field of nanotechnology. Recently, the use of bioresources in nanotechnology has gained significant attention from the scientific community due to its 100 % eco-friendly features, availability, and low costs. In this context, jute offers a considerable potential. Globally, its plant produces the second most common natural cellulose fibers and a large amount of jute sticks as a byproduct. The main chemical compositions of jute fibers and sticks, which have a trace amount of ash content, are cellulose, hemicellulose, and lignin. This makes jute as an ideal source of pure nanocellulose, nano-lignin, and nanocarbon preparation. It has also been used as a source in the evolution of nanomaterials used in various applications. In addition, hemicellulose and lignin, which are extractable from jute fibers and sticks, could be utilized as a reductant/stabilizer for preparing other nanomaterials. This review highlights the status and prospects of jute in nanotechnology. Different research areas in which jute can be applied, such as in nanocellulose preparation, as scaffolds for other nanomaterials, catalysis, carbon preparation, life sciences, coatings, polymers, energy storage, drug delivery, fertilizer delivery, electrochemistry, reductant, and stabilizer for synthesizing other nanomaterials, petroleum industry, paper industry, polymeric nanocomposites, sensors, coatings, and electronics, have been summarized in detail. We hope that these prospects will serve as a precursor of jute-based nanotechnology research in the future.

Preparation and Utilization of Jute-Derived Carbon: A Short Review

This article summarizes the preparation and applications of carbon derived from jute sticks and fibers that are low-cost, widely available, renewable, and environmentally friendly. Both the fibers and sticks are considered ideal candidates of carbon preparation because they are composed of cellulose, hemicelluloses, and lignin, and contain negligible ash content. Various carbon preparation methods including simple pyrolysis, pyrolysis with chemical and physical activations are discussed. The impacts of several parameters including types of activating agents, impregnation ratio, and temperature on their morphology, surface area, pore size, crystallinity, and surface functional groups are also emphasized. Various treatments to endow functionalization for increasing the practical applicability, such as chemical, physical, and physico-chemical methods, are discussed. In addition, applications of jute-derived carbon in various practical areas, including energy storage, water treatment, and sensors, are also highlighted in this report. Due to the porous fine structure and a large specific surface area, the jute-derived carbon could be considered as a powerful candidate material for various industrial applications. Finally, possible future prospects of jute-derived carbon for various applications are pointed out.

A Brief Description of Cyclic Voltammetry Transducer-Based Non-Enzymatic Glucose Biosensor Using Synthesized Graphene Electrodes

The essential disadvantages of conventional glucose enzymatic biosensors such as high fabrication cost, poor stability of enzymes, pH value-dependent, and dedicated limitations, have been increasing the attraction of non-enzymatic glucose sensors research. Beneficially, patients with diabetes could use this type of sensor as a fourth-generation of glucose sensors with a very low cost and high performance. We demonstrate the most common acceptable transducer for a non-enzymatic glucose biosensor with a brief description of how it works. The review describes the utilization of graphene and its composites as new materials for high-performance non-enzymatic glucose biosensors. The electrochemical properties of graphene and the electrochemical characterization using the cyclic voltammetry (CV) technique of electrocatalysis electrodes towards glucose oxidation have been summarized. A recent synthesis method of the graphene-based electrodes for non-enzymatic glucose sensors have been introduced along with this study. Finally, the electrochemical properties such as linearity, sensitivity, and the limit of detection (LOD) for each sensor are introduced with a comparison with each other to figure out their strengths and weaknesses.

Enhanced Cr(VI) removal by waste biomass derived nitrogen/oxygen co-doped microporous biocarbon

Herein, kitchen waste hydrolysis residue (KWHR) was utilized as the precursor to fabricate nitrogen/oxygen co-doped microporous biocarbons (NOMBs) with ultrahigh specific surface area via KOH activation. Activation temperature was found to be crucial for heteroatom doping and pore structure construction. Attractively, the obtained NOMB with high surface area (2417 m²/g) and microporosity (~ 90%) displayed an outstanding capacity of Cr(VI) removal (526.1 mg/g at pH 2). The kinetics and isotherm studies showed that the adsorption of Cr(VI) onto NOMB was well described by the pseudo-second-order kinetics and Langmuir isotherm. Moreover, it was found that Cr(VI) was partly reduced to Cr(III) during the removal process as the nitrogen/oxygen functionalities and unsaturated carbon bond played crucial roles of electron-donors, which revealed the fact that the removal of Cr(VI) by NOMB was attributed to the coupling of adsorption and reduction reaction. Overall, this study has demonstrated the possibility of preparing microporous biocarbons using KWHR as a renewable material and the resultant NOMB is of great potential to detoxify Cr(VI).

Synthesis of graphene by in situ catalytic chemical vapor deposition of reed as a carbon source for VOC adsorption

Few-layer graphene was synthesized by in situ catalytic carbon vapor deposition (CCVD) method, using reed as a carbon source and Ni, Cu, and Mg salts as the catalyst compounds. The synthesized graphene was also used for adsorption of VOCs. Furthermore, the effect of organic additives, sorbitol, and citric acid on catalyst compounds was investigated by temperature-programmed reduction analysis (H₂-TPR). The products' properties were characterized by thermo-gravimetric analysis (TGA), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), and Brunauer-Emmett-Teller (BET) surface area analysis. TEM and FE-SEM images confirmed the formation of graphene sheets. Activation of the graphene by phosphoric acid at 500 °C and then by CO₂ at 800 °C increased the surface area from 298 to 568 m²/g. Gasoline working capacity of the activated graphene was 65.24 g/l_adsorbent. Graphical abstract Few-layer graphene was synthesized by in situ catalytic carbon vapor deposition (CCVD) method using reed as a carbon source and Ni, Cu, and Mg salts as the catalyst compounds and used for adsorption of VOCs.

Activated Biomass-derived Graphene-based Carbons for Supercapacitors with High Energy and Power Density

Here, we present a facile and low-cost method to produce hierarchically porous graphene-based carbons from a biomass source. Three-dimensional (3D) graphene-based carbons were produced through continuous sequential steps such as the formation and transformation of glucose-based polymers into 3D foam-like structures and their subsequent carbonization to form the corresponding macroporous carbons with thin graphene-based carbon walls of macropores and intersectional carbon skeletons. Physical and chemical activation was then performed on this carbon to create micro- and meso-pores, thereby producing hierarchically porous biomass-derived graphene-based carbons with a high Brunauer-Emmett-Teller specific surface area of 3,657 m2 g-1. Owing to its exceptionally high surface area, interconnected hierarchical pore networks, and a high degree of graphitization, this carbon exhibited a high specific capacitance of 175 F g-1 in ionic liquid electrolyte. A supercapacitor constructed with this carbon yielded a maximum energy density of 74 Wh kg-1 and a maximum power density of 408 kW kg-1, based on the total mass of electrodes, which is comparable to those of the state-of-the-art graphene-based carbons. This approach holds promise for the low-cost and readily scalable production of high performance electrode materials for supercapacitors.