Carbon nanofibers prepared by the carbonization of self-assembled cellulose nanocrystals

The Thermal Behavior of Lyocell Fibers Containing Bis(trimethylsilyl)acetylene

This study focuses on the preparation of carbon fiber precursors from solutions of cellulose in N-methylmorpholine-N-oxide with the addition of bis(trimethylsilyl)acetylene, studying their structural features and evaluating thermal behavior. The introduction of a silicon-containing additive into cellulose leads to an increase in the carbon yield during carbonization of composite precursors. The type of the observed peaks on the differential scanning calorimetry (DSC) curves cardinally changes from endo peaks intrinsic for cellulose fibers to the combination of endo and exo peaks for composite fibers. For the first time, coefficient of thermal expansion (CTE) values were obtained for Lyocell fibers and composite fibers with bis(trimethylsilyl)acetylene (BTMSA). The study of the dependence of linear dimensions of the heat treatment fibers on temperature made it possible to determine the relation between thermal expansion coefficients of carbonized fibers and thermogravimetric curves, as well as to reveal the relationship between fiber shrinkage and BTMSA bis(trimethylsilyl)acetylene content. Carbon fibers from composite precursors are obtained at a processing temperature of 1200 °C. A study of the structure of carbon fibers by X-ray diffraction, Raman spectroscopy, and transmission electron microscopy made it possible to determine the amorphous structure of the fibers obtained.

The Effect of Alcohol Precipitants on Structural and Morphological Features and Thermal Properties of Lyocell Fibers

This research examines the possibilities of regulating the structure of cellulose precursor fibers spun from solutions in N-methylmorpholine-N-oxide when replacing aqueous coagulation baths with thermodynamically softer alcohol baths at different temperatures. The fibers were spun by the dry jet–wet method in isobutanol coagulation baths with a temperature of 25 °C and 70 °C. The study of the phase state of the solvent–coagulant system using viscometry and point cloud methods revealed the temperature-concentration regions of the single-phase and two-phase states of the system. Using elemental analysis, DSC (differential scanning calorimetry) and XRD (X-ray diffraction) methods, it was shown that just spun fibers, due to the presence of a residual amount of solvent and coagulant in them, regardless of the temperature of the precipitator, have an amorphous structure. Additional washing with water completely washed away the solvent and coagulant as well, however, the structure of cellulose changes slightly, turning into a defective amorphous-crystalline one. A relationship was found between the phase composition, structure, and properties of just spun fibers and precursors washed with water. Thus, the loss of structural ordering of both just spun and washed cellulose fibers leads to a decrease in strength characteristics and an increase in deformation. The thermal behavior of the fibers is determined by their phase composition. Fibers just spun into hot alcohol containing a coagulant and traces of solvent acquire thermal stability up to 330 °C. During the pyrolysis of the obtained precursors up to 1000 °C, the value of the carbon yield doubles. The amorphized structure of the obtained fibers allows us to consider it as a model when analyzing the transformation of the structure of precursors during thermolysis.

Advanced Materials through Assembly of Nanocelluloses

There is an emerging quest for lightweight materials with excellent mechanical properties and economic production, while still being sustainable and functionalizable. They could form the basis of the future bioeconomy for energy and material efficiency. Cellulose has long been recognized as an abundant polymer. Modified celluloses were, in fact, among the first polymers used in technical applications; however, they were later replaced by petroleum-based synthetic polymers. Currently, there is a resurgence of interest to utilize renewable resources, where cellulose is foreseen to make again a major impact, this time in the development of advanced materials. This is because of its availability and properties, as well as economic and sustainable production. Among cellulose-based structures, cellulose nanofibrils and nanocrystals display nanoscale lateral dimensions and lengths ranging from nanometers to micrometers. Their excellent mechanical properties are, in part, due to their crystalline assembly via hydrogen bonds. Owing to their abundant surface hydroxyl groups, they can be easily modified with nanoparticles, (bio)polymers, inorganics, or nanocarbons to form functional fibers, films, bulk matter, and porous aerogels and foams. Here, some of the recent progress in the development of advanced materials within this rapidly growing field is reviewed.