Synthesis and characterization of β-cyclodextrin–carboxymethyl cellulose–graphene oxide composite materials and its application for removal of basic fuchsin

Fabrication of carboxymethyl cellulose/graphene oxide/ZnO composite hydrogel for efficient removal of fuchsin dye from aqueous media

Hydrogels are hydrophilic, insoluble, and highly porous 3D networks capable of absorbing large amounts of water. This study aimed to develop a carboxymethyl cellulose/graphene oxide (CMC/GO) hydrogel, cross-linked with citric acid and modified with zinc oxide (ZnO) nanoparticles (CMC/GO/ZnO), synthesized via the sol-gel method. The formulated composite hydrogel samples were characterized by Fourier transmittance infrared spectroscopy (FTIR), scanning electron microscopy (SEM) analysis, X-ray diffraction (XRD), transmission electron microscopy (TEM), and thermo-gravimetric analysis (TGA). The hydrogels were tested for the adsorption of basic fuchsin (BF) dye from the aqueous medium under various conditions, such as adsorbent dosage, contact time, pH, and temperature, using batch adsorption. The adsorption data best fit the Langmuir and Temkin models, with maximum adsorption capacity (qmax) of 172.41 mg/g for CMC/GO and 303.03 mg/g for CMC/GO/ZnO. Optimal adsorption occurred at pH = 6 and within 30 min. The process followed a pseudo-second-order kinetic model, and thermodynamic results indicated that the adsorption process is physical, endothermic and spontaneous. The COOH groups in the hydrogels enhanced affinity for cationic dyes through hydrogen bonding and electrostatic interactions. Thus, CMC/GO and CMC/GO/ZnO hydrogels are efficient and promising adsorbents for environmental remediation.

Starch-based self-assembled three-dimensional network nanostructure materials for sustainable cascade adsorption

Toward the development of a sustainable utilization strategy for adsorption materials, a starch-based adsorbent starch-chitosan-tannic acid (St-CTS-TA) with a three-dimensional (3D) structure was fabricated in water via electrostatic and hydrogen bonding reactions between St, CTS, and TA without using toxic reducing agents or special instruments. St-CTS-TA demonstrated a high specific surface area of 37 m2/g as well as a mesoporous/macroporous distribution ranging from 30 to 80 nm, which enhanced the mass transfer of adsorbate and the exposure of catechol groups in TA. The Langmuir isotherm adsorption model revealed that the highest adsorption capacities of St-CTS-TA for Fe3+ and Co2+ were 1678.2 and 944.8 mg/g, respectively. Surprisingly, the specific surface area of St-CTS-TA increased from 37 to 87 and 42 m2/g after Fe3+ and Co2+ adsorption, respectively, and the resulting St-CTS-TA-Fe and St-CTS-TA-Co could continuously adsorb basic fuchsin (BF) and rhodamine B (RhB). The adsorption capacities of St-CTS-TA-Fe and St-CTS-TA-Co for BF/RhB were found to be 1854.79/401.19 mg/g and 2229.77/537.49 mg/g, respectively, based on the Langmuir isotherm adsorption model.

Development of carboxymethyl cellulose-graphene oxide biobased composite for the removal of methylene blue cationic dye model contaminate from wastewater

Utilizing Glutaraldehyde crosslinked sodium carboxymethyl cellulose (CMC-GA) hydrogel and its nanographene oxide composite (CMC-GA-GOx), an effective carboxymethyl cellulose-graphene oxide biobased composites adsorbent was developed for the adsorption removal of methylene blue (MB) cationic dye contaminate from industrial wastewater. The CMC-GA-GOx composites developed were characterized using FTIR, RAMAN, TGA, SEM, and EDX analysis instruments. Through batch experiments, several variables affecting the removal of MB dye, including the biocomposites GO:CMC composition, adsorption time, pH and temperature, initial MB concentration, adsorbent dosage, and NaCl concentration, were investigated under different conditions. The maximum dye removal percentages ranged between 93 and 98%. They were obtained using biocomposites CMC-GA-GO102 with 20% GO weight percent, adsorption time 25 min, adsorption temperature 25 °C, MB concentrations 10-30 ppm, adsorption pH 7.0, and 0.2 g adsorbent dose. The experimental data of the adsorption process suit the Langmuir isotherm more closely with a maximal monolayer adsorption capacity of 76.92 mg/g. The adsorption process followed the kinetic model of pseudo-second order. The removal of MB was exothermic and spontaneous from a thermodynamic standpoint. In addition, thermodynamic results demonstrated that adsorption operates most effectively at low temperatures. Finally, the reusability of the developed CMC-GA-GO102 has been proved through 10 successive cycles where only 14% of the MB dye removal percentage was lost. These results suggest that the developed CMC-GA-GO102 composite may be an inexpensive and reusable adsorbent for removing organic cationic dyes from industrial wastewater.

A novel terpolymer nanocomposite (carboxymethyl β-cyclodextrin-nano chitosan-glutaraldehyde) for the potential removal of a textile dye acid red 37 from water

Carboxymethyl β-cyclodextrin-nanochitosan-glutaraldehyde (CM-βCD:nChi:Glu) terpolymer was prepared as a nano-adsorbent for the removal of the anionic textile dye, acid red 37. The terpolymer nanocomposite formation and characterization were clarified by FTIR, XRD, scanning electron microscopy, TEM, Brunauer-Emmett-Teller specific surface area (BET-SSA), and zeta potential. The removal of the textile dye was investigated by using the batch adsorption method, investigating the effect of pH, dye concentration, adsorbent dose, contact time, and temperature. The results revealed that the maximum removal efficiency of 102.2 mg/L of the dye is about 99.67% under pH 6.0, the optimal contact time is 5 min, and the adsorbent dosage is 0.5 g/L. At 29°C; the adsorption capacity increased from 81.29 to 332.60 mg/g when the initial concentration of the dye was increased from 40.97 to 212.20 mg/L. Adsorption kinetics fitted well with the pseudo-second-order model with a good correlation (R ² = 0.9998). The Langmuir isotherm model can best describe the adsorption isotherm model. Based on the experimental results, the CM-βCD:nChi:Glu terpolymer has a promising potential as an efficient novel adsorbent for the removal of textile dye acid red 37 from contaminated water. This study's preparation techniques and demonstrated mechanisms offer valuable insights into the adsorbent-adsorbate interactions mechanism, analysis, challenges, and future directions of beta-cyclodextrin/chitosan-based adsorbents in wastewater treatment.

High Selectivity and Reusability of Biomass-Based Adsorbent for Chloramphenicol Removal

Recently, biomass-based materials have attracted increasing attention because of their advantages of low cost, environment-friendly and nonpollution. Herein, the feasibility of using corn stalk biomass fiber (CF) and Fe₃O₄ embedded chitosan (CS) as a novel biomass-based adsorbent (CFS) to remove chloramphenicol (CAPC) from aqueous solution. Structure of CFS was characterized by using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), Brunauer–Emmett–Teller (BET), scanning electron microscopy (SEM) and zeta potential techniques. The effects of solution pH, adsorption time and ion strength on the adsorption capacity were examined. Adsorption isotherms obtained from batch experiments were better fitted by Langmuir model compared with Freundlich model, Dubinin–Radushkevich model and Temkin model. Adsorption kinetic data matched well to the pseudo-second order kinetic model. CAPC adsorption was endothermic, spontaneous, and entropy-increasing nature on CFS. In addition, the CFS could be separated by an external magnetic field, recycled, and reused without any significant loss in the adsorption capacity of CAPC. Based on these excellent performances, there is potential that CFS can be considered as a proficient and economically suitable material for the CAPC removal from the water environment.

Cyclodextrin-Based Synthesis and Host-Guest Chemistry of Plasmonic Nanogap Particles with Strong, Quantitative, and Highly Multiplexable Surface-Enhanced Raman Scattering Signals

We developed a synthetic strategy to form cyclodextrin-based intrananogap particles (CIPs) with a well-defined ∼1 nm interior gap in a high yield (∼97%), and were able to incorporate 10 different Raman dyes inside the gap using the cyclodextrin-based host-guest chemistry, leading to strong, reproducible, and highly multiplexable surface-enhanced Raman scattering (SERS) signals. The average SERS enhancement factor (EF) for CIPs was 3.0 × 10⁹ with a very narrow distribution of the EFs that range from 9.5 × 10⁸ to 9.5 × 10⁹ for ∼95% of the measured particles. Remarkably, 10 different Raman dyes can be loaded within the nanogap of CIPs, and 6 different Raman dye-loaded CIPs with little spectral overlaps were distinctly detected for cancer cell imaging applications with a single excitation source. Our synthetic strategy provides new platforms in precisely forming plasmonic nanogap structures with all key features for widespread use of SERS including strong signal intensity, reliability in quantification of signal and multiplexing capability.

Utilization of Pacara Earpod tree (Enterolobium contortisilquum) and Ironwood (Caesalpinia leiostachya) seeds as low-cost biosorbents for removal of basic fuchsin

Wastes from the Pacara Earpod tree (Enterolobium contortisilquum) and Ironwood (Caesalpinia leiostachya) seeds were studied as biosorbents for the removal of basic fuchsin from waters. Both biosorbents were prepared and characterized by different analytical methods. The characterization data showed that both materials were mainly composed of lignin, cellulose, and hemicellulose. Both biosorbents exhibited roughened surfaces and surface functional groups such as C-H, C=O, C=C, C-O, C-N, and OH bonds. Furthermore, the XRD pattern shows an amorphous phase with a wide peak from 10 to 30° due to the lignin. In terms of dosage and pH, the use of 1 g L^-1 and 9.0, respectively, is recommended. The initial concentrations for the biosorption kinetics ranged from 50 to 500 mg L^-1, where the Pacara ear and the Ironwood reached an adsorption capacity of 145.62 and 100.743 mg g^-1 for the 500 mg L^-1. The pseudo-second-order was found to be the proper model for describing biosorption of basic fuchsin onto Pacara Earpod tree and Ironwood, respectively. For the isotherm experiments, the maximum experimental biosorption capacity was found to be 166.858 and 110.317 mg g^-1 for the Pacara Earpod and Ironwood for the initial concentration of 500 mg L^-1 at 328 K. The Langmuir and the Tóth models were the best for representing the equilibrium curves for the basic fuchsin on the Pacara Earpod and the Ironwood, respectively. Maximum adsorption capacities of 177.084 mg g^-1 and 136.526 mg g^-1 were achieved for the Pacara Earpod tree and Ironwood, respectively. The biosorption process was spontaneous, endothermic, and favorable for both biosorbents. The biosorbents were also applied for coloration removal of simulated textile effluents, reaching 66% and 54% for the Pacara Earpod and Ironwood, respectively. For the final application, the materials were used in fixed-bed biosorption, with an initial concentration of 200 mg L^-1, reaching breakthrough times of 710 and 415 min, leading to biosorption capacities of the column of 124.5 and 76.5 mg g^-1, for the Pacara Earpod and Ironwood, respectively.

Synthesis of New Cyclodextrin-Based Adsorbents to Remove Direct Red 83:1

Two cyclodextrins (CDs), γ– and hydroxypropyl (HP)–γ–CDs were used to synthesize new adsorbents by using epichlorohydrin (EPI) as cross-linking agent in order to remove Direct Red 83:1 (DR) from water. Both polymers were characterized in terms of Fourier spectroscopy, nuclear magnetic resonance, particle size distribution and thermogravimetric analysis. Experimental data for both polymers were well fitted to the pseudo-second order and intraparticle diffusion model, indicating that in the adsorption both chemical and physical interactions are essential in the removal of DR. Three different isotherm models were analyzed, concluding that γ–CDs–EPI followed the Temkin isotherm and HP–γ–CDs-EPI the Freundlich isotherm, these results suggested that the adsorption was happening onto heterogeneous surfaces. The results of the Gibbs free energy showed that the adsorption was spontaneous at room temperature. In order to eliminate the remaining dye after the polymer treatment, and advanced oxidation process (AOP) was considered, achieving more than 90% of removal combining both mechanisms.

Removal of Basic Fuchsin from water by using mussel powdered eggshell membrane as novel bioadsorbent: Equilibrium, kinetics, and thermodynamic studies

This study aims to remove organic cationic dye Basic Fuchsin (BF) by adsorption onto a low cost eggshell membrane (ESM) in batch mode at 293 K. XRD analysis confirms the amorphous nature of ESM meanwhile FTIR spectroscopy reveals the presence of several functional groups such as hydroxyl (-OH), sulfhydryl (-SH), carboxyl (-COOH), and amino (-NH₂). Morphological observations by SEM indicate its fibrous microstructure. BET analysis shows a surface area of 11.56 m² g^-1 and the presence of mesopores with a volume of 6.173 10^-3 cm³ g^-1. The value of pH_PZC of ESM is 7.05. The influence of adsorbent dose, contact time, pH, temperature and dye concentration is examined. The highest adsorption capacity around 48 mg.g^-1is achieved for a dye concentration 250 ppm, pH 6 and 25 °C. In addition, adsorption has been found to follow pseudo-second order kinetics. The analysis of the experimental data using linear forms based on Langmuir, Freundlich and Temkin isotherm models indicate that the best fit is obtained with Freundlich model. Thermodynamic parameters (Gibbs free energy, enthalpy, and entropy) reveal that the adsorption of BF onto ESM is an exothermic and spontaneous process. A comprehensive mechanism for BF adsorption by ESM has been proposed.

Preparation of a carboxymethyl β-cyclodextrin polymer and its rapid adsorption performance for basic fuchsin

The presence of dyes in a water system has potential adverse effects on the ecological environment. The conventional cyclodextrin (CD) polymer only has CD cavities as adsorption sites and exhibits slow adsorption for dye removal. In this study, we designed a novel carboxymethyl β-CD polymer (β-CDP-COOH). The structural properties of β-CDP-COOH were characterized as an irregular cross-linked polymer with negative surface charge, and the introduction of carboxymethyl groups greatly enhanced the adsorption ability of the β-CD polymer to basic fuchsin (BF). The maximum removal efficiency of β-CDP-COOH (96%) could be achieved within 1 min, whereas that of conventional β-CD polymer (70%) was achieved after 50 min. The adsorption mechanism revealed that the adsorption behavior of β-CDP-COOH could be effectively fitted with the pseudo-second-order kinetic model and Langmuir isotherm. Both CD cavities and carboxymethyl groups were effective adsorption sites, so β-CDP-COOH had an advantage in adsorption capacity over the conventional β-CD polymer. This study indicated that β-CDP-COOH is a potential highly efficient adsorbent for the removal of cationic dye contaminants.

Introduction of carboxymethyl groups greatly accelerated the adsorption rate of a β-CD polymer, and the removal efficiency reached 96% within 1 minute.

Fabrication of Carboxymethylcellulose/Metal-Organic Framework Beads for Removal of Pb(II) from Aqueous Solution

The ability to remove toxic heavy metals, such as Pb(II), from the environment is an important objective from both human-health and ecological perspectives. Herein, we describe the fabrication of a novel carboxymethylcellulose-coated metal organic material (MOF-5⁻CMC) adsorbent that removed lead ions from aqueous solutions. The adsorption material was characterized by Fourier-transform infrared spectroscopy, X-ray diffractometry, scanning electron microscopy, and X-ray photoelectron spectroscopy. We studied the functions of the contact time, pH, the original concentration of the Pb(II) solution, and adsorption temperature on adsorption capacity. MOF-5⁻CMC beads exhibit good adsorption performance; the maximum adsorption capacity obtained from the Langmuir isotherm-model is 322.58 mg/g, and the adsorption equilibrium was reached in 120 min at a concentration of 300 mg/L. The adsorption kinetics is well described by pseudo-second-order kinetics, and the adsorption equilibrium data are well fitted to the Langmuir isotherm model (R² = 0.988). Thermodynamics experiments indicate that the adsorption process is both spontaneous and endothermic. In addition, the adsorbent is reusable. We conclude that MOF-5⁻CMC is a good adsorbent that can be used to remove Pb(II) from aqueous solutions.