A review on environmental selenium issues

Occurrence, transport and sources of metals and metalloids in the Bangpakong River in the eastern economic corridor area of Thailand

The occurrence of elements in river water is affected by various factors, including mobility, weathering and transport processes and anthropogenic contributions. A total of six water sampling campaigns were conducted from 2021 to 2022 to study the factors affecting the occurrence of twelve elements (Al, As, Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb, Zn and Se) in the Bangpakong River. The total concentrations of all the elements were within the levels set by the national surface water quality standard. Comparisons of dissolved elemental concentrations in the study area with the global average for dissolved elemental concentrations in pristine rivers indicated contamination with Al, As, Co, Mn, Zn and Se in the river water. Based on the percentage of each element in particulates to the total concentration, Al (80.6 %), Cr (71.9 %), Cu (69.9 %), Fe (95.6 %), Mn (76.6 %), Pb (74.7 %), and Zn (70.6 %) were mainly transported in the particulate phase in both the dry and wet seasons. However, As (65.5 %), Co (60.3 %), and Se (77.6 %) were mainly transported in the dissolved phase in both seasons. The ratios of the dissolved Se concentration in river water to the Se concentration in the Earth's crust indicated significant and high mobility, especially in downstream sites, likely due to Se leaching from alluvial sediments. Seawater intrusion is likely the cause of As and Zn contamination in the dry season. Weathering of rocks and soils likely causes Al, Co, and Mn contamination in the wet season. The anthropogenic sources of contamination include the discharge of Mn and Zn from fertilizers in agriculture and the use of formulated feed in aquaculture. Approximately 52.98, 25.23, 5.68 and 0.63 tons of Fe, Al, Mn and Zn, respectively, are estimated to be transported from the river into the Gulf of Thailand each year.

Running the gauntlet; flyway-wide patterns of pollutant exposure in blood of migratory shorebirds

Shorebirds (order Charadriiformes) are among the world's most threatened avian taxa. Within the East Asian-Australasian Flyway (EAAF), a major threat to shorebirds' survival may be the gauntlet of pollution along the flyway. Metals, persistent organic pollutants (POPs), and per-/polyfluoroalkyl substances (PFASs) persist in the environment to the detriment of wildlife. In this study, we analysed element and PFAS concentrations in blood from 142 individuals across six species of Arctic-breeding migratory shorebirds with contrasting population trends, to discern species- and site-specific pollution differences, and determine how pollution correlated with population trends of EAAF shorebirds. Potential within-year pollution variations were investigated by blood-sampling birds at two sites, representing different points in the birds' annual migrations: staging in Taiwan on southward migrations and at non-breeding grounds in Western Australia (WA). Species' pollutant concentrations were compared to established population trends. Concentrations of potentially toxic elements were low in most individuals regardless of species. PFASs (range: <0.001-141 ng/g), Hg (<0.001-9910 ng/g) and Pb (<0.01-1210 ng/g) were higher in Taiwan than in WA (PFAS Taiwan median: 14.5 ng/g, WA median: 3.45 ng/g; Hg Taiwan: 338 ng/g, WA: 23.4 ng/g; Pb Taiwan: 36.8 ng/g, WA: 2.26 ng/g). Meanwhile As (range <0.001-8840 ng/g) and Se (290-47600 ng/g) were higher in WA than Taiwan (As Taiwan median: 500 ng/g, WA median: 1660 ng/g; Se Taiwan: 5490 ng/g, Se WA: 23700 ng/g). Nevertheless, pollutant concentrations in a subset of individuals may exceed sublethal effect thresholds (As, Se and PFASs). Finally, we found no consistent differences in pollution among species and demonstrated no correlation between pollution and population trends, suggesting pollution is likely not a major driver for population declines of EAAF shorebirds. However, ongoing and locally heavy environmental degradation and exposure to other contaminants not investigated here, such as POPs, warrants continued consideration when managing EAAF shorebird populations.

A critical review on selenium removal capacity from water using emerging non-conventional biosorbents

Anthropogenic-driven selenium (Se) contamination of natural waters has emerged as severe health and environmental concern. Lowering Se levels to safe limits of 40 μg-L-1 (recommended by WHO) presents a critical challenge for the scientific community, necessitating reliable and effective methods for Se removal. The primary obectives of this review are to evaluate the efficiency of different biosorbents in removing Se, understand the mechanism of adsorption, and identify the factors influencing the biosorption process. A comprehensive literature review is conducted to analyze various studies that have explored the use of modified biochars, iron oxides, and other non-conventional biosorbents for selenium removal. The assessed biosorbents include biomass, microalgae-based, alginate compounds, peats, chitosan, and biochar/modified biochar-based adsorbents. Quantitative data from the selected studies analyzed Se adsorption capacities of biosorbents, were collected considering pH, temperature, and environmental conditions, while highlighting advantages and limitations. The role of iron impregnation in enhancing the biosorption efficiency is investigated, and the mechanisms of Se adsorption on these biosorbents at different pH levels are discussed. A critical literature assessment reveals a robust understanding of the current state of Se biosorption and the effectiveness of non-conventional biosorbents for Se removal, providing crucial information for further research and practical applications in water treatment processes. By understanding the strengths and limitations of various biosorbents, this review is expected to scale-up targeted research on Se removal, promoting the development of innovative and cost-effective adsorbents, efficient and sustainable approaches for Se removal from water.

The Ozonolysis of Methylated Selenide Compounds in the Atmosphere: Isotopes, Kinetics, Products, and Mechanisms

Selenium (Se) is an essential micronutrient with an important atmospheric component in its biogeochemical cycle. In this cycle, phytoplankton form volatile organic Se species, such as dimethyl selenide (CH3SeCH3) and dimethyl diselenide (CH3SeSeCH3), which are emitted into the atmosphere. To predict the atmospheric fate of these methylated Se compounds, we investigated their ozonolysis reaction. We used proton-transfer-reaction time-of-flight mass spectrometry to quantify atmospheric Se and its isotopes, and used this method in kinetic and product studies. The ozonolysis of CH3SeCH3 proceeded with a rate constant of (7.4 ± 2.2) × 10-17 cm3 molec-1 s-1 at 26 ± 1 °C with an activation energy of 50 ± 14 kJ mol-1 forming dimethyl selenoxide (CH3Se(O)CH3). Comparatively, CH3SeSeCH3 reacted with O3 at (2.6 ± 0.9) × 10-17 cm3 molec-1 s-1 at 27 ± 1 °C with an activation energy of 56 ± 5 kJ mol-1 forming methylselinic acid (CH3Se(O)OH). At 20 ppbv of O3, the atmospheric lifetimes of CH3SeCH3 and CH3SeSeCH3 are 7.6 and 22 h, respectively. The Se oxidation products were confirmed by synthesis and can serve as new atmospheric tracers of methylated Se compounds. Overall, we measured Se isotopes in real time and determined the rate constants, activation energies, and oxidation products. These mechanisms can now be used to determine the quantitative atmospheric fate of Se toward O3, and thus its distribution within a changing climate.

Relationships between growth indicators, liver and kidney function markers, and blood concentrations of essential and potentially toxic elements in environmentally exposed young children

Environmental exposure to multiple metals and metalloids is widespread, leading to a global concern relating to the adverse health effects of mixed-metals exposure, especially in young children living around industrial areas. This study aimed to quantify the concentrations of essential and potentially toxic elements in blood and to examine the potential associations between multiple elements exposures, growth determinants, and liver and kidney function biomarkers in children living in several industrial areas in Dhaka, Bangladesh. The blood distribution of 20 trace elements As, Ag, Bi, Br, Cd, Co, Cr, Cu, I, Mn, Hg, Mo, Ni, Pb, Se, Sb, Tl, V, U, and Zn, growth determinants such as body mass index and body fats, blood pressure, liver and kidney injury biomarkers including serum alanine aminotransferase and alkaline phosphatase activities, serum calcium, and creatinine levels, blood urea nitrogen, and hemoglobin concentrations, and glomerular filtration rate were measured in 141 children, aged six to 16 years. Among these elements, blood concentrations of Ag, U, V, Cr, Cd, Sb, and Bi were measured below LOQs and excluded from subsequent statistical analysis. This comprehensive study revealed that blood concentrations of these elements in children, living in industrial areas, exceeded critical reference values to varying extents; elevated exposure to As, Pb, Br, Cu, and Se was found in children living in multiple industrial areas. A significant positive association between elevated blood Tl concentration and obesity (β = 0.300, p = 0.007) and an inverse relationship between lower As concentration and underweight (β = -0.351, p < 0.001) compared to healthy weight children indicate that chronic exposure to Tl and As may influence the metabolic burden and physical growth in children. Concentration-dependent positive associations were observed between the blood concentrations of Cu, Se, and Br and hepatic- and renal dysfunction biomarkers, an inverse association with blood Mo and I level, however, indicates an increased risk of Cu, Se, and Br-induced liver and kidney toxicity. Further in-depth studies are warranted to elucidate the underlying mechanisms of the observed associations. Regular biomonitoring of elemental exposures is also indispensable to regulate pollution in consideration of the long-term health effects of mixed-elements exposure in children.

A critical analysis of sources, pollution, and remediation of selenium, an emerging contaminant

Selenium (Se) is an essential metalloid and is categorized as emerging anthropogenic contaminant released to the environment. The rise of Se release into the environment has raised concern about its bioaccumulation, toxicity, and potential to cause serious damages to aquatic and terrestrial ecosystem. Therefore, it is extremely important to monitor Se level in environment on a regular basis. Understanding Se release, anthropogenic sources, and environmental behavior is critical for developing an effective Se containment strategy. The ongoing efforts of Se remediation have mostly emphasized monitoring and remediation as an independent topics of research. However, our paper has integrated both by explaining the attributes of monitoring on effective scale followed by a candid review of widespread technological options available with specific focus on Se removal from environmental media. Another novel approach demonstrated in the article is the presentation of an overwhelming evidence of limitations that various researchers are confronted with to overcome achieving effective remediation. Furthermore, we followed a holistic approach to discuss ways to remediate Se for cleaner environment especially related to introducing weak magnetic field for ZVI reactivity enhancement. We linked this phenomenal process to electrokinetics and presented convincing facts in support of Se remediation, which has led to emerge 'membrane technology', as another viable option for remediation. Hence, an interesting, innovative and future oriented review is presented, which will undoubtedly seek attention from global researchers.

Near Quantitative Removal of Selenate and Sulfate Anions from Wastewaters by Cocrystallization with Chelating Hydrogen-Bonding Guanidinium Ligands

Selenium (Se) has become an environmental contaminant of aquatic ecosystems as a result of human activities, particularly mining, fossil fuel combustion, and agricultural activities. By leveraging the high sulfate concentrations relative to Se oxyanions (i.e., SeO _n ^2-, n = 3, 4) present in some wastewaters, we have developed an efficient approach to Se-oxyanion removal by cocrystallization with bisiminoguanidinium (BIG) ligands that form crystalline sulfate/selenate solid solutions. The crystallization of the sulfate, selenate and selenite, oxyanions and of sulfate/selenate mixtures with five candidate BIG ligands are reported along with the thermodynamics of crystallization and aqueous solubilities. Oxyanion removal experiments with the top two performing candidate ligands show a near quantitative removal (>99%) of sulfate or selenate from solution. When both sulfate and selenate are present, there is near quantitative removal (>99%) of selenate, down to sub-ppb Se levels, with no discrimination between the two oxyanions during cocrystallization. Reducing the selenate concentrations by 3 orders of magnitude or more relative to sulfate, as found in many wastewaters, led to no measurable loss in Se removal efficiencies. This work offers a simple and effective alternative to selective separation of trace amounts of highly toxic selenate oxyanions from wastewaters, to meet stringent regulatory discharge limits.

Lack of sufficient evidence to support a positive role of selenium status in depression: a systematic review

CONTEXT

Globally, depression affects more than 322 million people. Studies exploring the relationship between diet and depression have revealed the benefits of certain dietary patterns and micronutrients in attenuating the symptoms of this disorder. Among these micronutrients, selenium stands out because of its multifaceted role in the brain.

OBJECTIVE

To assess the impact of selenium intake and status on symptoms of depression.

DATA SOURCES

A systematic search was performed in databases, including PubMed, Web of Science, EMBASE, PsycINFO, Scopus, and gray literature (on April 6, 2021, updated on January 28, 2022), without restrictions of date, language, or study type.

DATA EXTRACTION

Studies of adults (18-60 y of age) with depression or depressive symptoms were included. Data on selenium biomarkers and/or intake were included. The risk of bias was assessed using the Joanna Briggs Institute checklists.

DATA ANALYSIS

Of the 10 studies included, 2 were cohorts (n = 13 983 and 3735), 3 were cross-sectional (n = 736, 7725, and 200), 1 was case-control (n = 495), and 4 were randomized controlled trials (n = 30, 11, 38, and 63). Several studies have indicated that low selenium intake or concentration may be associated with symptoms of depression. However, this association was inconsistent across the studies included in this systematic review; due to the high heterogeneity, it was not possible to perform meta-analyses. The main contributing factors to the high heterogeneity include the different methodological designs, methods for diagnosing depression, selenium assessment, and clinical conditions.

CONCLUSION

Overall, there is insufficient evidence to support a positive role of selenium status in depression. Studies with more accurate methods and adequate assessment of selenium status are needed to better understand the role of this nutrient in depression.

SYSTEMATIC REVIEW REGISTRATION

PROSPERO registration no. CRD42021220683.

Selenium Nanowire Formation by Reacting Selenate with Magnetite

The mobility of ⁷⁹Se, a fission product of ²³⁵U and long-lived radioisotope, is an important parameter in the safety assessment of radioactive nuclear waste disposal systems. Nonradioactive selenium is also an important contaminant of drainage waters from black shale mountains and coal mines. Highly mobile and soluble in its high oxidation states, selenate (Se(VI)O₄^2-) and selenite (Se(IV)O₃^2-) oxyanions can interact with magnetite, a mineral present in anoxic natural environments and in steel corrosion products, thereby being reduced and consequently immobilized by forming low-solubility solids. Here, we investigated the sorption and reduction capacity of synthetic nanomagnetite toward Se(VI) at neutral and acidic pH, under reducing, oxygen-free conditions. The additional presence of Fe(II)_aq, released during magnetite dissolution at pH 5, has an effect on the reduction kinetics. X-ray absorption spectroscopy analyses revealed that, at pH 5, trigonal gray Se(0) formed and that sorbed Se(IV) complexes remained on the nanoparticle surface during longer reaction times. The Se(0) nanowires grew during the reaction, which points to a complex transport mechanism of reduced species or to active reduction sites at the tip of the Se(0) nanowires. The concomitant uptake of aqueous Fe(II) and Se(VI) ions is interpreted as a consequence of small pH oscillations that result from the Se(VI) reduction, leading to a re-adsorption of aqueous Fe(II) onto the magnetite, renewing its reducing capacity. This effect is not observed at pH 7, where we observed only the formation of Se(0) with slow kinetics due to the formation of an oxidized maghemite layer. This indicates that the presence of aqueous Fe(II) may be an important factor to be considered when examining the environmental reactivity of magnetite.

How sulfur species can accelerate the biological immobilization of the toxic selenium oxyanions and promote stable hexagonal Se0 formation

Toxic selenium oxyanions and sulfur species are often jointly present in contaminated waters and soils. This study investigated the effect on kinetics and resulting products for bio-reduction of selenium oxyanions in the presence of biologically produced sulfur resulting from bio-oxidation of sulfide in (bio)gas-desulfurization (bio-S⁰) and of sulfate. Selenite and selenate (~2 mmol L^-1) bio-reduction was studied in batch up to 28 days at 30 ^oC and pH 7 using lactic acid and a sulfate-reducing sludge, 'Emmtec'. Bio-S⁰ addition increased the selenite removal rate, but initially slightly decreased selenate reduction rates. Selenite reacted with biologically generated sulfide resulting in selenium-sulfur, which upon further bio-reduction creates a sulfur bio-reduction cycle. Sulfate addition increased the bio-reduction rate for both selenite and sulfate. Bio-S⁰ or sulfate promoted hexagonal selenium formation, whereas without these, mostly amorphous Se⁰ resulted. With another inoculum, 'Eerbeek', bio-S⁰ accelerated the selenite reduction rate less than for 'Emmtec' because of lower sulfur and higher selenite bio-reduction rates. Bio-S⁰ addition increased the selenate reduction rate slightly and accelerated hexagonal selenium formation. Hexagonal selenium formation is advantageous because it facilitates separation and recovery and is less mobile and toxic than amorphous Se⁰. Insights into the interaction between selenium and sulfur bio-reduction are valuable for understanding environmental pathways and considerations regarding remediation and recovery.

Selenium distribution in cultivated Argosols and Gleyosols of dry and paddy lands: A case study in Sanjiang Plain, Northeast China

Distribution pattern of selenium (Se) fractions in soil could influence Se content in crops and thereby intake of Se in human body. In order to investigate the effects of soil types and farming conditions on Se distribution in small-scaled cultivated land developed under the same conditions of climate, topography and parent materials, two types of soils (i.e., Argosols and Gleyosols) from paddy and dry lands in the Sanjiang Plain of Northeast China were selected. Total Se (T-Se) content in Argosols was influenced by organic carbon (Org C) content and pH of bulk topsoil. In Gleyosols, it was mainly affected by Org C content in dry land and pH in paddy land, respectively. In rice root associated topsoil, organic matter associated Se (OM-Se) accounted for 70% of T-Se. Compared with pH (median 6.10) and OM weakly bound Se (OW-Se) (0.14 ± 0.04 mg kg^-1) of Argosols, the higher pH (median 6.77) resulted in less OW-Se (0.10 ± 0.04 mg kg^-1) of Gleyosols. Vertical distribution of Se in borehole cores within the depth of 0-900 cm was mainly affected by the soil type. Se accumulated mainly within 0-150 cm depth (horizon A, E and B) in Argosols and above 40 cm depth (horizon H), existing prominently as OM strongly bound Se (OS-Se), in Gleyosols. Within the depth of 0-150 cm, various Se fractions for both soils were probably controlled by reductive fixation and complexation of Org C; In the alkaline paddy land, DOM-complexed Se was the main composition of A-Se. The findings of this study could help in understanding the mechanisms of Se distribution and enrichment in soils developed under different formation processes and farming conditions.

Discriminative Long-Distance Transport of Selenate and Selenite Triggers Glutathione Oxidation in Specific Subcellular Compartments of Root and Shoot Cells in Arabidopsis

Selenium is an essential trace element required for seleno-protein synthesis in many eukaryotic cells excluding higher plants. However, a substantial fraction of organically bound selenide in human nutrition is directly or indirectly derived from plants, which assimilate inorganic selenium into organic seleno-compounds. In humans, selenium deficiency is associated with several health disorders Despite its importance for human health, selenium assimilation and metabolism is barely understood in plants. Here, we analyzed the impact of the two dominant forms of soil-available selenium, selenite and selenate, on plant development and selenium partitioning in plants. We found that the reference plant Arabidopsis thaliana discriminated between selenate and selenite application. In contrast to selenite, selenate was predominantly deposited in leaves. This explicit deposition of selenate caused chlorosis and impaired plant morphology, which was not observed upon selenite application. However, only selenate triggered the accumulation of the macronutrient sulfur, the sister element of selenium in the oxygen group. To understand the oxidation state-specific toxicity mechanisms for selenium in plants, we quantified the impact of selenate and selenite on the redox environment in the plastids and the cytosol in a time-resolved manner. Surprisingly, we found that selenite first caused the oxidation of the plastid-localized glutathione pool and had a marginal impact on the redox state of the cytosolic glutathione pool, specifically in roots. In contrast, selenate application caused more vigorous oxidation of the cytosolic glutathione pool but also impaired the plastidic redox environment. In agreement with the predominant deposition in leaves, the selenate-induced oxidation of both glutathione pools was more pronounced in leaves than in roots. Our results demonstrate that Se-species dependent differences in Se partitioning substantially contribute to whole plant Se toxicity and that these Se species have subcellular compartment-specific impacts on the glutathione redox buffer that correlate with toxicity symptoms.

An economical strategy towards the managing of selenium pollution from contaminated water: A current state-of-the-art review

During the last few decades, contamination of selenium (Se) in groundwater has turned out to be a major environmental concern to provide safe drinking water. The content of selenium in such contaminated water might range from 400 to 700 μg/L, where bringing it down to a safe level of 40 μg/L for municipal water supply employing appropriate methodologies is a major challenge for the global researcher communities. The current review focuses mostly on the governing selenium remediation technologies such as coagulation-flocculation, electrocoagulation, bioremediation, membrane-based approaches, adsorption, electro-kinetics, chemical precipitation, and reduction methods. This study emphasizes on the development of a variety of low-cost adsorbents and metal oxides for the selenium decontamination from groundwater as a cutting-edge technology development along with their applicability, and environmental concerns. Moreover, after the removal, the recovery methodologies using appropriate materials are analyzed which is the need of the hour for the reutilization of selenium in different processing industries for the generation of high valued products. From the literature survey, it has been found that hematite modified magnetic nanoparticles (MNP) efficiently adsorb Se (IV) (25.0 mg/g) from contaminated groundwater. MNP@hematite reduced Se (IV) concentration from 100 g/L to 10 g/L in 10 min at pH 4-9 using a dosage of 1 g/L. In 15 min, the magnetic adsorbent can be recycled and regenerated using a 10 mM NaOH solution. The adsorption and desorption efficiencies were over 97% and 82% for five consecutive cycles, respectively. To encourage the notion towards scale-up, a techno-economic evaluation with possible environmentally sensitive policy analysis has been introduced in this article to introspect the aspects of sustainability. This type of assessment is anticipated to be extremely encouraging to convey crucial recommendations to the scientific communities in order to produce high efficiency selenium elimination and further recovery from contaminated groundwater.

Selenium removal from water using adsorbents: A critical review

Selenium (Se) has become an increasingly serious water contamination concern worldwide. It is an essential micronutrient for humans and animals, however, can be extremely toxic if taken in excess. Sorption can be an effective treatment for Se removal from a wide range of water matrices. However, despite the synthesis and application of numerous adsorbents for remediation of aqueous Se, there has been no comprehensive review of the sorption capacities of various natural and synthesized sorbents. Herein, literature from 2010 to 2021 considering Se remediation using 112 adsorbents has been critically reviewed and presented in several comprehensive tables including: clay minerals and waste materials (presented in Table 1); zero-valent iron, iron oxides, and binary iron-based adsorbents (Table 2); other metals-based adsorbents (Table 3); carbon-based adsorbents (Table 4); and other adsorbents (Table 5). Each of these tables, and their relevant sections, summarizes preparation/modification methods, sorption capacities of various Se adsorbents, and proposed model/mechanisms of adsorption. Furthermore, future perspectives have been provided to assist in filling noted research gaps for the development of efficient Se adsorbents for real-world applications. This review will help in preliminary screening of various sorbent media to set up Se treatment technologies for a variety of end-users worldwide.

Selenium: An Element of Life Essential for Thyroid Function

Selenium (Se), a microelement essential for life, is critical for homeostasis of several critical functions, such as those related to immune-endocrine function and signaling transduction pathways. In particular, Se is critical for the function of the thyroid, and it is particularly abundant in this gland. Unfortunately, Se deficiency is a very common condition worldwide. Supplementation is possible, but as Se has a narrow safety level, toxic levels are close to those normally required for a correct need. Thus, whether the obtaining of optimal selenium concentration is desirable, the risk of dangerous concentrations must be equally excluded. This review addressed the contribution by environment and food intake on Se circulating levels (e.g., geographical factors, such as soil concentration and climate, and different quantities in food, such as nuts, cereals, eggs, meat and fish) and effects related to its deficiency or excess, together with the role of selenium and selenoproteins in the thyroid pathophysiology (e.g., Hashimoto's thyroiditis and Graves' disease).

Conversion of cattle manure into functional material to remove selenate from wastewater

Herein, pyrolysis of cattle manure was conducted to synthesize an effective material for removing heavy metals (e.g., selenium) from water environments. To remove selenate from aqueous solution, iron-impregnated cattle manure biochar (Fe/CM-biochar) was synthesized. The Fe-impregnation was performed by pre-treating cattle manure before its pyrolysis. The pretreatment increased the biochar yield. Influence of various factors such as contacting time, initial selenate concentration, reaction temperature, pH, and presence of coexisting anions were explored by performing batch adsorption experiments. The selenate adsorption reached equilibrium within 15 min. The Langmuir model was better fitted to equilibrium adsorption data than the Freundlich model. The maximum adsorption capacity of Fe/CM-biochar was calculated to be 52.56 mg-Se/g, which is superior to other adsorbents reported in the literature. As the reaction temperature increased in the range (15-35) °C, selenate adsorption on Fe/CM-biochar showed an endothermic and nonspontaneous reaction. The enthalpy change during selenate adsorption was 18.44 kJ/mol, which ranges in physical adsorption. The increase of solution pH (3-11) reduced the selenate adsorption (46.4-37.7 mg-Se/g). The extent of co-existing anion impact on selenate adsorption followed an order of HPO₄^2- > HCO₃^- > SO₄^2- > NO₃^-. These results indicate that Fe/CM-biochar is an effective functional material for the removal of selenate from wastewater.

Environmental Impacts of Selenium Contamination: A Review on Current-Issues and Remediation Strategies in an Aqueous System

In both aquatic and terrestrial environment, selenium contamination may exist at concentrations above the micronutrient limit. Since there is such a narrow bandwidth between which selenium concentration is acceptable, the health of the public may be at risk of selenium toxicity once the concentration increases beyond a threshold. Selenium contamination in an aqueous environment can occur due to anthropogenic activities and/or from natural sources. This study presents a review of the forms of selenium, inorganic and organic selenium contamination, mobilization, analytical methods for various forms of selenium and remediation strategies. The review also provides recent advances in removal methods for selenium from water including bioremediation, precipitation, coagulation, electrocoagulation, adsorption, nano-zerovalent iron, iron co-precipitation and other methods. A review of selenomethionine and selenocysteine removal strategy from industrial wastewaters is presented. Selenium resource recovery from copper ore processing has been discussed. Various analytical methods used for selenium and heavy metal analysis were compared. Importantly, existing knowledge gaps were identified and prospective areas for further research were recommended.

Simultaneous Determination of As, Bi, Sb, Se, Te, Hg, Pb and Sn by Small-Sized Electrothermal Vaporization Capacitively Coupled Plasma Microtorch Optical Emission Spectrometry Using Direct Liquid Microsampling

The simultaneous determination of chemical vapor-generating elements involving derivatization is difficult even by inductively coupled plasma optical emission spectrometry or mass spectrometry. This study proposes a new direct liquid microsampling method for the simultaneous determination of As, Bi, Se, Te, Hg, Pb, and Sn, using a fully miniaturized set-up based on electrothermal vaporization capacitively coupled plasma microtorch optical emission spectrometry. The method is cost-effective, free from non-spectral interference, and easy to run by avoiding derivatization. The method involves the vaporization of analytes from the 10 µL sample and recording of episodic spectra generated in low-power (15 W) and low-Ar consumption (150 mL min⁻¹) plasma microtorch interfaced with low-resolution microspectrometers. Selective vaporization at 1300 °C ensured the avoidance of non-spectral effects and allowed the use of external calibration. Several spectral lines for each element even in the range 180–210 nm could be selected. Generally, this spectral range is examined with large-scale instrumentation. Even in the absence of derivatization, the obtained detection limits were low (0.02–0.75 mg kg⁻¹) and allowed analysis of environmental samples, such as cave and river sediments. The recovery was in the range of 86–116%, and the accuracy was better than 10%. The method is of general interest and could be implemented on any miniaturized or classical laboratory spectrometric instrumentation.

Cathodic selenium recovery in bioelectrochemical system: Regulatory influence on anodic electrogenic activity

Metal(loid)s are used in various industrial activities and widely spread across the environmental settings in various forms and concentrations. Extended releases of metal(loid)s above the regulatory levels cause environmental and health hazards disturbing the ecological balance. Innovative processes for treating the metal(loid)-contaminated sites and recovery of metal(loid)s from disposed waste streams employing biotechnological routes provide a sustainable way forward. Conventional metal recovery technologies demand high energy and/or resource inputs, which are either uneconomic or unsustainable. Microbial electrochemical systems are promising for removal and recovery of metal(loid)s from metal(loid)-laden wastewaters. In this communication, a bioelectrochemical system (BES) was designed and operated with selenium (Se) oxyanion at varied concentrations as terminal electron acceptor (TEA) for reduction of selenite (Se⁴⁺) to elemental selenium (Se⁰) in the abiotic cathode chamber. The influence of varied concentrations of Se⁴⁺ towards Se⁰ recovery at the cathode was also evaluated for its regulatory role on the electrometabolism of anode-respiring bacteria. This study observed 26.4% Se⁰ recovery (cathode; selenite removal efficiency: 73.6%) along with organic substrate degradation of 74% (anode). With increase in the initial selenite concentration, there was a proportional increase in the dehydrogenase activity. Bioelectrochemical characterization depicted increased anodic electrogenic performance with the influence of varied Se⁴⁺ concentrations as TEA and resulted in a maximum power density of 0.034 W/m². The selenite reduction (cathode) was evaluated through spectroscopic, compositional and structural analysis. X-ray diffraction and Raman spectroscopy showed the amorphous nature, while Energy Dispersive X-ray spectroscopy confirmed precipitates of the deposited Se⁰ recovered from the cathode chamber. Scanning electron microscopic images clearly depicted the Se⁰ depositions (spherical shaped; sized approximately 200 nm in diameter) on the electrode and cathode chamber. This study showed the potential of BES in converting soluble Se⁴⁺ to insoluble Se⁰ at the abiotic cathode for metal recovery.