Laser-induced fluorometric determination of albumin using longwave absorbing molecular probes

Probing the interaction of iron complex containing N3S2 macrocyclic ligand with bovine serum albumin using spectroscopic techniques

The interaction of bovine serum albumin (BSA) with seven-coordination iron (II) complex containing sulfur-based macrocyclic ligand was investigated by means of UV/vis absorption spectroscopy and fluorescence quenching technique. The accurate fluorescence spectra are obtained by using Inner filter effect (IFE) correction. The apparent association constant, k_app, the number of binding sites, n, and the apparent binding constant K_SV were found to be 0.95 × 10³ M^-1, 0.96, and 6.13 × 10⁴ M^-1, respectively. It found that BSA molecules are adsorbed on the surface of iron (II) complex by electrostatic interaction. The quenching mechanism is discussed involving energy transfer from BSA to iron (II) complex.

Assembly of New Merocyanine Chromophores with a 1,8-Naphthalimide Core by a New Method for the Synthesis of the Methine Function

A new method for the synthesis of the monomethine group using nitro as a leaving group in an SN-Ar reaction is described. A series of novel merocyanine dyes has been synthesised and their photophysical properties have been elucidated. The longest wavelength absorption occurs in the range 519–619 nm and the molar absorptivities vary with the substituents and are in the range 1000–47700 L mol–1 cm–1. The dyes show high chemical and photostability. One example from the series has the ability to distinguish methanol from ethanol. The introduction of a quinoid fragment into the structure leads to a pronounced intramolecular charge transfer and hence a noticeable positive solvatochromism. The structures and electronic properties of the compounds have been studied by density functional theory (DFT) and time-dependent DFT.

Towards a more representative in vitro method for fish ecotoxicology: morphological and biochemical characterisation of three-dimensional spheroidal hepatocytes

The use of fish primary cells and cell lines offer an in vitro alternative for assessment of chemical toxicity and the evaluation of environmental samples in ecotoxicology. However, their uses are not without limitations such as short culture periods and loss of functionality, particularly with primary tissue. While three-dimensional (spheroid) technology is now established for in vitro mammalian toxicity studies, to date it has not been considered for environmental applications in a model aquatic species. In this study we report development of a reproducible six-well plate, gyratory-mediated method for rainbow trout (Oncorhynchus mykiss) hepatocyte spheroid culture and compare their functional and biochemical status with two-dimensional (2D) monolayer hepatocytes. Primary liver spheroid formation was divided into two stages, immature (1-5 days) and mature (≥6 days) according to size, shape and changes in functional and biochemical parameters (protein, glucose, albumin and lactate dehydrogenase). Mature spheroids retained the morphological characteristics (smooth outer surface, tight cell-cell contacts) previously described for mammalian spheroids as demonstrated by light and scanning electron microscopy. Glucose production and albumin synthesis were significantly higher in mature spheroids when compared to conventional 2D monolayer cultures (P < 0.01) and increased as spheroids matured (P < 0.01). Basal lactate dehydrogenase (LDH) leakage significantly decreased during spheroid formation and was significantly lower than 2D cultures (P < 0.01). It is therefore suggested that mature spheroids can maintain a high degree of functional, biochemical and morphological status over-time in culture that is superior to conventional 2D models and can provide realistic organotypic responses in vitro. Trout spheroids that take ~6-8 days to reach maturity would be suitable for use in acute toxicological tests and since it is possible to culture individual spheroids for over a month, there is potential for this work to lead towards in vitro bioaccumulation alternatives and to conduct high throughput screens of chronic exposure. This is an important step forward for developing alternative in vitro tools in future fish ecotoxicological studies.

Telore R, Sekar N. Synthesis of novel fluorescent 1,3,5-trisubstituted triazine derivatives and photophysical property evaluation of fluorophores and their BSA conjugates

Cyanuric chloride was allowed to react with

Effects of homogeneous media, binary mixtures and microheterogeneous media on the fluorescence and fluorescence probe properties of some benzo[b][1,8]naphthyridiens with HSA and BSA

A rapid and efficient method for the synthesis of various poly-substituted benzo[b][1,8]naphthyridines in high yield has been developed via the Friedländer condensation of 2-aminoquinoline-3-carbaldehyde 1 with various alicyclic ketones in a base catalyst (aq. potassium hydroxide). A series of benzo[b][1,8]naphthyridines branched with various side-chains and substituents were prepared with the aim of being investigated as a fluorescent agents. Electronic absorption and fluorescence properties of some representative benzonaphthyridines (3d, 5b and 21f) in homogeneous organic solvents, dioxane-water binary mixtures and in the microheterogeneous media (sodium dodecyl sulphate (SDS), cetyl trimethyl ammonium bromide (CTAB) and Triton-X100 micelles) have been examined. A linear correlation between solvent polarity and fluorescence properties was observed. Further, the interaction of these benzonaphthyridines (3d, 5b and 21f) with human serum albumin (HSA) and bovine serum albumin (BSA) in phosphate buffer have been examined by UV-vis absorption and fluorescence spectroscopy. The fluorescence intensity of 3d, 5b and 21f increases with the increasing HSA and BSA concentration. These benzonaphthyridines also quench the 345 nm fluorescence of BSA in phosphate buffer (λ(ex) 280 nm). These compounds have potential for use as neutral and hydrophobic fluorescence probes for examining the microenvironments in proteins, polymers, micelles, etc.

Synthesis and characterization of novel 2, 2'-bipyrimidine fluorescent derivative for protein binding

BACKGROUND

Fluorescent dyes with biocompatible functional group and good fluorescence behavior are used as biosensor for monitoring different biological processes as well as detection of protein assay. All reported fluorophore used as sensors are having high selectivity and sensitivity but till there is more demand to synthesized new fluorophore which have improved fluorescence properties and good biocompatibility.

RESULTS

Novel 4, 4'-(1, 1'-(5-(2-methoxyphenoxy)-[2, 2'-bipyrimidine]-4, 6-diyl)bis(1H-pyrazol-3, 1-diyl)) dianiline fluorescent dye was synthesized by multistep synthesis from 2-phenylacetonitrile, 2-chloropyrimidine and 2-methoxyphenol. This dye has absorption at 379 nm with intense single emission at 497 nm having fairly good quantum yield (0.375) and Stokes shift. The intermediates and dye were characterized by FT-IR, 1H NMR, 13C NMR and Mass spectral analysis. The pyrazole bipyrimidine based fluorescent dye possessing two amino groups suitable for binding with protein is reported. Its utility as a biocompatible conjugate was explained by conjugation with bovine serum albumin. The method is based on direct fluorescence detection of fluorophore-labelled protein before and after conjugation. Purified fluorescent conjugate was subsequently analyzed by fluorimetry. The analysis showed that the tested conjugation reaction yielded fluorescent conjugates of the dye through carbodiimide chemistry.

CONCLUSION

In summery synthesized fluorophore pyrazole-bipyrimidine has very good interaction towards protein bovine serum albumin and it acts as good candidate for protein assay.

Controlled modulation of serum protein binding and biodistribution of asymmetric cyanine dyes by variation of the number of sulfonate groups

To assess the suitability of asymmetric cyanine dyes for in vivo fluoro-optical molecular imaging, a comprehensive study on the influence of the number of negatively charged sulfonate groups governing the hydrophilicity of the DY-67x family of asymmetric cyanines was performed. Special attention was devoted to the plasma protein binding capacity and related pharmacokinetic properties. Four members of the DY-67x cyanine family composed of the same main chromophore, but substituted with a sequentially increasing number of sulfonate groups (n  =  1-4; DY-675, DY-676, DY-677, DY-678, respectively), were incubated with plasma proteins dissolved in phosphate-buffered saline. Protein binding was assessed by absorption spectroscopy, gel electrophoresis, ultrafiltration, and dialysis. Distribution of dye in organs was studied by intraveneous injection of 62 nmol dye/kg body weight into mice (n  =  12; up to 180 minutes postinjection) using whole-body near-infrared fluorescence imaging. Spectroscopic studies, gel electrophoresis, and dialysis demonstrated reduced protein binding with increasing number of sulfonate groups. The bovine serum albumin binding constant of the most hydrophobic dye, DY-675, is 18 times higher than that of the most hydrophilic fluorophore, DY-678. In vivo biodistribution analysis underlined a considerable influence of dye hydrophilicity on biodistribution and excretion pathways, with the more hydrophobic dyes, DY-675 and DY-676, accumulating in the liver, followed by strong fluorescence signals in bile and gut owing to accumulation in feces and comparatively hydrophilic DY-678-COOH accumulating in the bladder. Our results demonstrate the possibility of selectively controlling dye-protein interactions and, thus, biodistribution and excretion pathways via proper choice of the fluorophore's substitution pattern. This underlines the importance of structure-property relationships for fluorescent labels. Moreover, our data could provide the basis for the rationalization of future contrast agent developments.

Novel fluorophores as building blocks for optical probes for in vivo near infrared fluorescence (NIRF) imaging

Aiming at the identification of new fluorescent reporters for targeted optical probes, we assessed the application-relevant features of a novel asymmetric cyanine, DY-681, in comparison to the only clinically approved dye indocyanine green (ICG), the golden imaging standard Cy5.5, and the asymmetric cyanine DY-676 successfully exploited by us for the design of different contrast agents. This comparison included the analysis of the spectroscopic properties of the free fluorophores and their thermal stability in aqueous solution as well as their cytotoxic potential. In addition, the absorption and emission features of IgG-conjugated DY-681 were examined. The trimethine DY-681 exhibited spectral features closely resembling that of the pentamethine Cy5.5. Its high thermal stability in phosphate buffer saline (PBS) solution in conjunction with its low cytotoxicity, reaching similar values as determined for Cy5.5 and DY-676, renders this dye more attractive as ICG and, due to its improved fluorescence quantum yield in PBS, also superior to DY-676. Although in PBS, Cy5.5 was still more fluorescent, the fluorescence quantum yields (Phi(f)) of DY-681 and Cy5.5 in PBS containing 5 mass-% bovine serum albumin (BSA) were comparable. Labeling experiments with DY-681 and the model antibody IgG revealed promisingly high Phi(f) values of the bioconjugated dye.

Synthesis of functionalized ZnSe nanoparticles and their applications in the determination of bovine serum albumin

Luminescent quantum dots (QDs)-semiconductor nanocrystals were promising alternative to organic dyes for fluorescence-based applications. In this paper, we developed procedures to use mercaptoacetic acid (MAA) to modify ZnSe nanoparticles and made the nanoparticles to be soluble for the quantitative and selective determination of bovine serum albumin (BSA). Maximum fluorescence intensity was produced at pH 7.0, with excitation and emission wavelengths at 242 and 348 nm, respectively. Under optimal conditions, the straight line equation: Delta(F) = 0.38 + 0.34 C (microg/ml) was found between the relative fluorescence intensity and the concentration of BSA in the range of 9.6-124.8 microg/ml, and the limit of detection was 2 microg/ml.

Synchronous fluorescence determination of human serum albumin with methyl blue as a fluorescence probe

A new synchronous fluorescence scan analysis was developed for the determination of HSA with high sensitivity with a triphenylmethane acid dye methyl blue as a fluorescence probe. When Deltalambda=140 nm, the synchronous fluorescence peak of methyl blue is located at 323 nm and the synchronous fluorescence intensity of the methyl blue is significantly increased in the presence of trace HSA due to the complex formed between methyl blue and HSA at pH 4.1. Under optimal conditions, the calibration graphs are linear over the range 0.03-266.0 and 266.0-665.0 microg mL(-1) for human serum albumin (HSA). Limit of determination were 0.03 microg mL(-1) for HSA. In the detection of HSA in human serum samples, this method gave values close the clinical data got from hospital.

LIF detection of peptides and proteins in CE

CE- and microchip-based separations coupled with LIF are powerful tools for the separation, detection and determination of biomolecules. CE with certain configurations has the potential to detect a small number of molecules or even a single molecule, thanks to the high spatial coherence of the laser source which permits the excitation of very small sample volumes with high efficiency. This review article discusses the use of LIF detection for the analysis of peptides and proteins in CE. The most common laser sources, basic instrumentation, derivatization modes and set-ups are briefly presented and special attention is paid to the different fluorogenic agents used for pre-, on- and postcapillary derivatization of the functional groups of these compounds. A table summarizing major applications of these derivatization reactions to the analysis of peptides and proteins in CE-LIF and a bibliography with 184 references are provided which covers papers published to the end of 2005.

Laser-induced fluorescence technique for DNA and proteins separated by capillary electrophoresis

Recent developments in capillary electrophoresis (CE) in conjunction with laser-induced fluorescence (LIF) using long-wavelength (maximum excitation wavelength>500 nm) dyes are reviewed. These dyes are particularly of interest when conducting the analyses of biopolymers by CE-LIF using He-Ne lasers. These systems are benefited from low background, low costs, easy maintenance, and compactness. Derivatizations of DNA and proteins with fluorescent or nonfluorescent chemicals can be carried out prior to, during, or after separations. With the advantages of sensitivity, rapidity, and high efficiency, the applications of CE-LIF to the analysis of polymerase chain reaction products, DNA sequencing, trace analysis of proteins, and single cell analysis have been presented.

Dye-binding protein assay using a long-wave-absorbing cyanine probe

A simple and fast protein assay that involves the binding of water-soluble sulfonate heptamethylene cyanine to protein is described. The binding of the dye to protein causes a shift in the absorption maximum of the dye from 778 to 904 nm, and the increase in absorption at 904 nm is monitored. This assay is very reproducible, of good color stability for at least 80 min, and sensitive at the 100 ng/mL level of human serum albumin (HSA) when a spectrophotometer with near-infrared wavelength is used to measure absorbance. Few chemicals except ionic surfactants such as cetyltrimethylammonium bromide and sodium dodecyl sulfonate interfere with the assay. Purified proteins have different capacities to interact with the dye; under the experimental conditions, the linear ranges of bovine serum albumin (BSA), HSA and gamma-IgG were 200-2000, 100-2400, and 200-3000 ng/mL, respectively. The relative standard deviation for the five replicate determinations of 1200 ng/mL BSA is 2.1%.

Novel two-color fluorescence probe with extreme specificity to bovine serum albumin

We report on strong, highly specific and stochiometric binding to bovine serum albumin of novel fluorescence probe FA, 2-(6-diethylaminobenzo[b]furan-2-yl)-3-hydroxychromone, that exhibits a very characteristic two-band fluorescence spectrum. Both absorption band and two fluorescence bands of FA are very sensitive to non-covalent interactions in the immediate environment of the probe. Multiparametric analysis of this spectroscopic information allows us to conclude that the binding site is characterized by very low polarity, high extent of screening from aqueous environment and unusually high electronic polarizability. The latter suggests the proximal location of probe FA to the aromatic amino acid residues in the binding site. The new probe can be proposed for the study of interaction of ligands and drugs of different nature with serum albumins.

Long-wavelength long-lifetime luminophores

We describe a new approach to making luminophores that display long emission wavelengths, long decay times, and high quantum yields. These luminophores are covalently linked pairs with a long-lifetime resonance-energy-transfer donor and a long-wavelength acceptor. The donor was a ruthenium (Ru) metal-ligand complex. The acceptor was the Texas Red. The donor and acceptor were covalently linked by polyproline spacers. The long-lifetime donor results in a long-lived component in the acceptor decay, which is due to RET. Importantly, the quantum yield of the luminophores approaches that of the higher quantum yield acceptor, rather than the lower quantum yield typical of metal-ligand complexes. The emission maxima and decay time of such tandem luminophores can be readily adjusted by selection of the donor, acceptor, and distance between them. Luminophores with these useful spectral properties can also be donor-acceptor pairs brought into close proximity by some biochemical association reaction. Luminophores with long-wavelength emission and long lifetimes can have numerous applications in biophysics, clinical diagnostics, DNA analysis, and drug discovery.

Fluorescence properties of albumin blue 633 and 670 in plasma and whole blood

We have determined the fluorescence characteristics of two long wavelength dyes, albumin blue 633 (AB633) and 670 (AB670), in plasma and blood to evaluate the possibility of making direct fluorescence sensing measurements in blood. Using binding and lifetime measurements we were also able to show that these dyes bind selectively to human serum albumin (HSA) in plasma and blood. By measuring changes in the mean lifetime of AB670 with changes in the HSA concentration, we showed that lifetime-based sensing can be used to monitor HSA concentrations using these albumin blue dyes. Anisotropy measurements for AB633 and AB670 in plasma and blood revealed high anisotropy values for these dyes in these media. Exploiting these high anisotropies, we were also able to determine HSA concentrations in plasma and blood mimics using changes in AB670 anisotropy with HSA concentration. These results show that, apart from being able to make fluorescence measurements directly in plasma and blood, it is possible to sense directly for specific plasma/blood components using fluorescent probes that bind preferentially to them.

On the possibility of long-wavelength long-lifetime high-quantum-yield luminophores

We describe an approach to creating a new class of luminophores which display both long wavelength emissions exceeding 600 nm and long lifetimes. These luminophores are based on resonance energy transfer (RET) from a long lifetime donor to a short lifetime but long wavelength acceptor. We demonstrated the possibility of obtaining these desirable spectral properties using donors and acceptors noncovalently bound to DNA. The donor was a ruthenium (Ru) metal-ligand complex in which one of the diimine ligands intercalated into double-helix DNA. The acceptors were either nile blue, TOTO-3, or TO-PRO-3. Upon binding of the acceptor to donor-labeled DNA, we found that the acceptor quantum yield was remarkably enhanced so that the wavelength-integrated intensities of the donor and acceptor bound to DNA were many-fold greater than the intensity of the donor and acceptor alone when separately bound to DNA. The origin of this effect is efficient energy transfer from the donor. Under these conditions the effective overall quantum yield approaches that of the acceptor. Importantly, the increased quantum yield can be obtained while maintaining usefully long apparent acceptor lifetimes of 30 to 80 ns. The effect of an increased quantum yield from a low quantum yield donor may find use in assays to detect macromolecular binding interactions. These results suggest the synthesis of covalently linked donor-acceptor pairs with the desirable spectral properties of long wavelength emission, high quantum yield, and moderately long lifetimes for gated detection.

Fluorescence properties of rhodamine 800 in whole blood and plasma

We have characterized the fluorescence spectral properties of rhodamine 800 (Rh800) in plasma and blood in order to test the possibility of making clinical fluorescence measurements in whole blood without separation steps. Rh800 was used because of its absorption at red/near-infrared wavelengths away from the absorption bands of hemoglobin. We utilized the front-face illumination and detection to minimize the effects of absorption and/or scatter during measurements. The presence of Rh800 was detected in plasma and blood using steady-state fluorescence measurements. Absorption due to hemoglobin reduced the Rh800 intensity from the blood. Fluorescence lifetime measurements in plasma and blood showed that it is possible to recover lifetime parameters of Rh800 in these media. We obtained mean lifetimes of 1.90 and 1.86 ns for Rh800 in plasma and blood, respectively. Using the recently described modulation sensing method, we quantified the concentrations of Rh800 in plasma and blood. Rh800 was detected at a concentration of as low as 2 microM in both media. High anisotropy values were obtained for Rh800 in plasma and blood using steady-state and anisotropy decay measurements, implying the tight binding of this probe to the contents of these media. This binding can be exploited to monitor the concentrations of different blood components using already existing or new red-emitting probes that will be specially designed to bind to these components with high specificity. To test this possibility of direct measurements in blood, we used Rh800 to monitor albumin in the presence of red blood cells. Increase in the polarization of Rh800 as the concentration of albumin was increased in the presence of the red cells showed the feasibility of such measurements.

Ultrasensitive near-infrared laser-induced fluorescence detection in capillary electrophoresis using a diode laser and avalanche photodiode

A sensitive fluorescence detector for capillary electrophoresis consisting of a semiconductor near-infrared diode laser and a single photon avalanche diode (SPAD) is described. The sensitivity of this system was demonstrated by the separation and analysis of four tricarbocyanine dyes using capillary electrophoresis and a running buffer consisting of 98% methanol and 2% water with 40 mM borate (pH 9.4). The LOD for the dye, IR-132, was found to be 4.41 zmol with the dynamic range found to be approximately four orders of magnitude in concentration. Based on the sampling volume of the system, the number of molecules actually detected at this LOD was approximately 27. To further demonstrate the utility of this diode-based detector, various amino acids were derivatized with a highly anionic near-IR labelling dye. The conjugates were separated in a running buffer comprised of predominately methanol and a cationic surfactant added to reverse the electroosmotic flow. The LOD values for various amino acids were found to be in the low zmol range.

Microalbuminuria and borderline-increased albumin excretion determined with a centrifugal analyzer and the Albumin Blue 580 fluorescence assay

We report a new automated fluorescence assay for determination of albumin in urine. The dye Albumin Blue 580 specifically binds to albumin with exhibition of strong red fluorescence. The albumin concentration is calculated from emission intensity at 616 nm (excitation at 590 nm) and a calibration curve. Two Cobas Fara programs cover working ranges of 2–200 and 1–50 mg/L with detection limits of 1.4 and 0.4 mg/L, respectively. Within-run CVs (n = 10) ranged from 1.7% (189 mg/L) to 8.9% (7.2 mg/L) for 2–200 mg/L and from 2.9% (43.3 mg/L) to 5.7% (2.3 mg/L) for the 1–50 mg/L range. A test of urine samples (n = 100) submitted to routine analysis gave results that agreed well with those by the Behring nephelometric assay: AB 580 = 0.922 (± 0.010) BNA + 4.16 (± 0.78). No interference was detected from other urine components, including several proteins and 46 drugs. The high specificity and sensitivity make the method ideal for determination of microalbuminuria. In addition, the method is fast, inexpensive, and well-suited for clinical laboratory application and thus may be used instead of immunoassays.