Optimization and validation of a new method of analysis for polycyclic aromatic hydrocarbons in sewage sludge by liquid chromatography after microwave assisted extraction

Seasonal Distribution, Source Identification, and Toxicological Risk Assessment of Polycyclic Aromatic Hydrocarbons (PAHs) in Sediments from Wadi El Bey Watershed in Tunisia

Surface sediments were collected from the Watershed of Wadi El Bey in Tunisia to evaluate the degree of polycyclic aromatic hydrocarbons (PAHs) contamination. Sediments were collected during different seasons in 14 sites that received wastes from domestic effluent, industrial discharge, and agricultural drainage wastes. Twenty-six individual PAHs were analyzed. The total PAH contents (Σ PAHs) in surface sediments showed wide variability, ranging from 6.89 ± 0.05 to 340 ± 0.1 ng g^-1. The 4-, 5-, and 6-ring compounds were the most abundant PAHs detected at the majority of sites. Diagnostic concentration ratios between pairs of PAHs and molecular indices, calculated with the purpose of drawing information about pollution sources, indicated that PAHs were of both petrogenic and pyrolytic origins. Toxic contaminants concentrations were determined according to the numerical effect-based sediment quality guidelines (SQGs). PAH levels did not exceed the SQGs, indicating that PAHs seem to pose low and occasional toxicity risks. Total carcinogenicity and mutagenicity (TEQ_BaP and MEQ_BaP) ranged from 0.08 to 65 ng and from 0.02 to 135.0 ng g^-1 of dry weight, respectively. Among the seven carcinogenic PAHs, BaP accounted for the majority of the potency and could potentially be used as a unique indicator of PAH toxicity. This study provides a baseline to promote environmental protection programs and pollution monitoring/control in Watershed and coastal areas.

Distribution of polycyclic aromatic hydrocarbons in sediments of Akaki River, Lake Awassa, and Lake Ziway, Ethiopia

The quantification of 14 polycyclic aromatic hydrocarbons (PAHs) was carried out in sediment samples collected from Akaki River, Lake Awassa, and Lake Ziway, Ethiopia. The concentration of PAHs in the samples was determined using gas chromatography-mass spectrometry (GC-MS) in selected ion monitoring (SIM) mode, after microwave-assisted extraction (MAE), using acetone/n-hexane (1:1, v/v) mixture. The accuracy of the method was determined by extracting and analyzing New York/New Jersey waterway sediment standard reference material (SRM 1944). The measured concentrations of PAHs in SRM 1944 agreed well with the certified values. In samples from Akaki River, Lake Awassa, and Lake Ziway, the total content of PAHs determined ranged from 0 to 3070 ng/g (average 534 ng/g), 24.9 to 413 ng/g (average 169 ng/g), and 15.0 to 305 ng/g (average 175 ng/g), respectively. Source ratios indicated that the PAHs were mainly from petrogenic origin. Sediments from all sampling sites indicated negligible levels of toxicity with no risk of adverse biological effects.

Occupational exposure to polycyclic aromatic hydrocarbons in airborne particulate matter: validation and application of a gas chromatography-mass spectrometry analytical method

This study concerns the validation of an analytical method for the measurement of occupational exposure to trace levels of polycyclic aromatic hydrocarbons (PAHs) in airborne particulate matter (APM). Personal exposure to selected PAHs of five workers occupationally exposed to urban pollution in Rome, Italy, was evaluated. The samples were collected over 10 days evenly distributed during winter and summer of 2008. Polycyclic aromatic hydrocarbons were collected by a sampling pump and trapped in polytetrafluoroethylene filters; ultrasonic extraction was applied to extract PAH species from the matrix with toluene, and the concentrated extract was quantitatively analyzed by GC/MS. The analytical method was optimized and validated using a standard reference material of urban dust (SRM 1649a). Detection limits ranged from 0.8 ng per sample for indeno [1,2,3-cd] pyrene to 20.4 ng for sample for anthracene. Experimental results of the 50 personal samples collected showed that phenanthrene was the predominant polycyclic aromatic hydrocarbon [95% CI (32.42-41.13 ng m(-3))]; the highest benzo[a]pyrene concentration was 2.58 ng m(-3), approximately 2-fold higher than European annual target values (1 ng m(-3)). Seasonal variations of personal exposure to selected PAHs suggested higher emissions and reduced atmospheric reactivity of PAH compounds in winter. The analytical method was a suitable procedure for the determination of 13 of the 16 priority PAHs in APM personal samples and can be considered a useful tool to evaluate occupational exposure to low PAH levels.

A cost effective, sensitive, and environmentally friendly sample preparation method for determination of polycyclic aromatic hydrocarbons in solid samples

A simple, cost effective, and yet sensitive sample preparation technique was investigated for determining Polycyclic Aromatic Hydrocarbons (PAHs) in solid samples. The method comprises ultrasonic extraction, Stir Bar Sorptive Extraction (SBSE), and thermal desorption-gas chromatography-mass spectrometry to increase analytical capacity in laboratories. This method required no clean-up, satisfied PAHs recovery, and significantly advances cost performance over conventional extraction methods, such as Soxhlet and Microwave Assisted Extraction (MAE). This study evaluated three operational parameters for ultrasonic extraction: solvent composition, extraction time, and sample load. A standard material, SRM 1649 a (urban dust), was used as the solid sample matrix, and 12 priority PAHs on the US Environmental Protection Agency (US EPA) list were analyzed. Combination of non-polar and polar solvents ameliorated extraction efficiency. Acetone/hexane mixtures of 2:3 and 1:1 (v/v) gave the most satisfactory results: recoveries ranged from 63.3% to 122%. Single composition solvents (methanol, hexane, and dichloromethane) showed fewer recoveries. Comparing 20 min with 60 min sonication, longer sonication diminished extraction efficiencies in general. Furthermore, sample load became a critical factor in certain solvent systems, particularly MeOH. MAE was also compared to the ultrasonic extraction, and results determined that the 20-min ultrasonic extraction using acetone/hexane (2:3, v/v) was as potent as MAE. The SBSE method using 20 mL of 30% alcohol-fortified solution rendered a limit of detection ranging from 1.7 to 32 ng L(-1) and a limit of quantitation ranging from 5.8 to 110 ng L(-1) for the 16 US EPA PAHs.

Estrogenic and AhR activities in dissolved phase and suspended solids from wastewater treatment plants

The distribution of estrogen receptor (ERalpha) and Aryl Hydrocarbon Receptor (AhR) activities between the dissolved phase and suspended solids were investigated during wastewater treatment. Three wastewater treatment plants with different treatment technologies (waste stabilization ponds (WSPs), trickling filters (TFs) and activated sludge supplemented with a biofilter system (ASB)) were sampled. Estrogenic and AhR activities were detected in both phases in influents and effluents. Estrogenic and AhR activities in wastewater influents ranged from 41.8 to 79 ng/L E(2) Eq. and from 37.9 to 115.5 ng/L TCDD Eq. in the dissolved phase and from 5.5 to 88.6 ng/g E(2) Eq. and from 15 to 700 ng/g TCDD Eq. in the suspended solids. For both activities, WSP showed greater or similar removal efficiency than ASB and both were much more efficient than TF which had the lowest removal efficiency. Moreover, our data indicate that the efficiency of removal of ER and AhR activities from the suspended solid phase was mainly due to removal of suspended solids. Indeed, ER and AhR activities were detected in the effluent suspended solid phase indicating that suspended solids, which are usually not considered in these types of studies, contribute to environmental contamination by endocrine disrupting compounds and should therefore be routinely assessed for a better estimation of the ER and AhR activities released in the environment.

Optimisation of pressurised liquid extraction by experimental design for quantification of pesticides and alkyl phenols in sludge, suspended materials and atmospheric fallout by liquid chromatography-tandem mass spectrometry

The study proposes an analytical method to quantify 10 alkylphenols and 12 pesticides at ultra-trace levels by liquid chromatography in reverse mode coupled to positive electrospray ionisation-tandem mass spectrometry. The extraction procedure from environmental solids was optimised by pressurised liquid extraction using acetonitrile:isopropanol (1:1, v/v). The influence of several extraction experimental factors, temperature, pressure, duration and number of cycles, related to the PLE was investigated by an original and efficient chemometric approach. The optimised extraction method (80 degrees C, 40 bar, 10 min, 1 cycle) exhibited recoveries between 67 and 127% with RSD mostly under 13%. The whole method was applied to real samples: sludge, suspended materials, atmospheric fallouts and roof deposit. Pollutant levels were between 1 microg kg(-1) and 5.9 mg kg(-1).

Novel approach to microwave-assisted extraction and micro-solid-phase extraction from soil using graphite fibers as sorbent

A single-step extraction-cleanup procedure involving microwave-assisted extraction (MAE) and micro-solid-phase extraction (micro-SPE) has been developed for the analysis of polycyclic aromatic hydrocarbons (PAHs) from soil samples. Micro-SPE is a relatively new extraction procedure that makes use of a sorbent enclosed within a sealed polypropylene membrane envelope. In the present work, for the first time, graphite fiber was used as a sorbent material for extraction. MAE-micro-SPE was used to cleanup sediment samples and to extract and preconcentrate five PAHs in sediment samples prepared as slurries with addition of water. The best extraction conditions comprised of microwave heating at 50 degrees C for a duration of 20 min, and an elution (desorption) time of 5 min using acetonitrile with sonication. Using gas chromatography (GC)-flame ionization detection (FID), the limits of detection (LODs) of the PAHs ranged between 2.2 and 3.6 ng/g. With GC-mass spectrometry (MS), LODs were between 0.0017 and 0.0057 ng/g. The linear ranges were between 0.1 and 50 or 100 microg/g for GC-FID analysis, and 1 and 500 or 1000 ng/g for GC-MS analysis. Granular activated carbon was also used for the micro-SPE device but was found to be not as efficient in the PAH extraction. The MAE-micro-SPE method was successfully used for the extraction of PAHs in river and marine sediments, demonstrating its applicability to real environmental solid matrixes.

Investigation of potentially bioavailable and sequestrated forms of polycyclic aromatic hydrocarbons during sewage sludge composting

The present study focuses on the influence of the composting process on the formation of potentially bioavailable and sequestrated PAH fractions. The potentially bioavailable fraction was determined by means of a mild-solvent extraction (with n-butanol). The total and potentially bioavailable PAH content was evaluated in the consecutive composting stages, i.e. at the onset of the experiment, after the stabilization phase (on the 35th day), and after the maturation phase (on the 76th day). Four municipal sewage sludges with differentiated PAH content were selected for the present experiment. Eleven PAHs from the US EPA list (with exception of naphthalene, acenaphthylene, acenaphtene, fluorene and benz[ah]anthracene) were determined for the purpose of this experiment. The content of the total PAHs ranged from 3052 to 10352microg kg(-1). The share of the potentially bioavailable fraction was at a similar level in the sludge samples tested and ranged from 75% to 81%. Greater differences were noted in the share of the bioavailable fraction in the case of individual PAH groups. The influence of the composting process on the contribution of the potentially bioavailable fraction of the PAH clearly depended on the stage of the experiment and sewage sludge type. However, in the case of all sludges, a lowering of the bioavailable fraction by 19-52% as compared to the level at the outset of the experiment was observed. During the first phase (stabilization) of the sewage sludge composting process, a reduction of the PAH content took place mainly at the expense of potentially bioavailable fraction, whereas in the second phase (maturation), sequestration processes predominated. The above phenomenon was most clearly visible for the 6-rings PAHs.

Application of surfactants and microemulsions to the extraction of pyrene and phenanthrene from soil with three different extraction methods

In the present work, the use of surfactants and oil-in-water (O/W) microemulsions as alternative extractants in accelerated solvent extraction (ASE) for the extraction of polycyclic aromatic hydrocarbons (pyrene and phenanthrene) from soils was investigated. In particular, the effect of each individual component within the microemulsions, i.e., oil phase, surfactant and co-surfactant, and extraction conditions on the percentage recovery was systematically studied. When compared to the water and organic solvent, the important findings were that the common surfactant solutions at the concentrations above their critical micelle concentrations (CMC) were shown to enhance the percentage recovery at the lower extraction temperature. Moreover, the highest percentage recovery can be obtained using microemulsion as the extractant. The chemical component within the microemulsions and relative amounts of the oil phase appeared to play a much more significant role in ensuring high percentage recovery. Finally, an overall comparison between the percentage recoveries obtained with ultrasound-assisted extraction (UAE), microwave-assisted extraction (MAE) and ASE using organic solvents, surfactants and microemulsions as extractants was exhibited.

Analysis of 27 polycyclic aromatic hydrocarbons by matrix solid-phase dispersion and isotope dilution gas chromatography-mass spectrometry in sewage sludge from the Spanish area of Madrid

A method for the determination of 27 polycyclic aromatic hydrocarbons (PAHs) in sludge from wastewater treatment plants (WWTPs) located in urban, industrial or rural zones is presented. PAHs were extracted by matrix solid-phase dispersion (MSPD) assisted by sonication. Purification of extracts was carried out by solid-phase extraction with C(18) and PAHs were eluted with acetonitrile. PAHs were determined by isotope dilution gas chromatography with electron impact mass spectrometric detection in the selected ion-monitoring mode (GC-MS-SIM), using deuterated PAHs as internal standards. The limits of detection ranged from 0.03 ng/g for acenaphthylene to 0.45 ng/g for benzo[b]naphtho[2,1-d]thyophene. After optimization, the method was validated with a certified reference sludge. The proposed analytical method was applied to determine PAH levels in sewage sludge samples collected from 19 water treatment plants located in the province of Madrid (Spain). In most of the examined samples, phenanthrene was the main compound with a mean concentration of 1062 ng/g. PAHs were detected in all of the samples, with total concentrations between 390 and 6390 ng/g dry weight for the 27 PAHs analyzed and from 310 to 5120 ng/g dry weight for the sum of the 10 PAHs considered in the draft European Union directive.

Simultaneous sonication-assisted extraction, and determination by gas chromatography–mass spectrometry, of di-(2-ethylhexyl)phthalate, nonylphenol, nonylphenol ethoxylates and polychlorinated biphenyls in sludge from wastewater treatment plants

Di-(2-ethyl-hexyl)phthalate (DEHP), nonylphenol, nonylphenol mono- and diethoxylates (NPEs) and polychlorinated biphenyls (PCBs) are organic pollutants in sewage sludge which have to be monitored in the European Union according to a future Sludge Directive. In the present work, an analytical method for the simultaneous extraction and determination of DEHP, NPEs and PCBs is proposed for the routine analysis of these compounds in sludge from wastewater treatment plants. All the compounds were simultaneously extracted by sonication with hexane and analysed by gas chromatography-mass spectrometry (GC-MS) in electronic impact mode. Recoveries achieved were 105% for DEHP, 61.4-88.6% for NPEs and 55.8-108.3% for PCBs with relative standard deviation bellow 10%. Limits of quantification were 65 microg kg(-1) for DEHP, from 630 to 2504 microg kg(-1) for NPEs and from 5.4 to 10.6 microg kg(-1) for PCBs in dried sludge. The applicability of the proposed method was evaluated by the determination of these compounds in sludge from wastewater treatment plants in Seville (South Spain).

Sample preparation of sewage sludge and soil samples for the determination of polycyclic aromatic hydrocarbons based on one-pot microwave-assisted saponification and extraction

A microwave-assisted sample preparation (MASP) procedure was developed for the analysis of polycyclic aromatic hydrocarbons (PAHs) in sewage sludge and soil samples. The procedure involved the simultaneous microwave-assisted extraction of PAHs with n-hexane and the hydrolysis of samples with methanolic potassium hydroxide. Because of the complex nature of the samples, the extracts were submitted to further cleaning with silica and Florisil solid-phase extraction cartridges connected in series. Naphthalene, acenaphthene, fluorene, phenanthrene, anthracene, fluoranthene, pyrene, benz[a]anthracene, chrysene, benzo[e]pyrene, benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[a]pyrene, dibenz[a,h]anthracene, benzo[g,h,i]perylene, and indeno[1,2,3-cd]pyrene, were considered in the study. Quantification limits obtained for all of these compounds (between 0.4 and 14.8 microg kg(-1) dry mass) were well below of the limits recommended in the USA and EU. Overall recovery values ranged from 60 to 100%, with most losses being due to evaporation in the solvent exchange stages of the procedure, although excellent extraction recoveries were obtained. Validation of the accuracy was carried out with BCR-088 (sewage sludge) and BCR-524 (contaminated industrial soil) reference materials.

Comparison of solid phase extraction, saponification and gel permeation chromatography for the clean-up of microwave-assisted biological extracts in the analysis of polycyclic aromatic hydrocarbons

The feasibility of different clean-up procedures was studied for the determination of polycyclic aromatic hydrocarbons (PAHs) in biota samples such as oysters, mussels and fish liver. In this sense, once the samples were extracted--essentially with acetone and in a microwave system--and before they could be analysed by gas chromatography-mass spectrometry (GC-MS), three different approaches were studied for the clean-up step: solid phase extraction (SPE), microwave-assisted saponification (MAS) and gel permeation chromatography (GPC). The main aim of this work was to maximise the recoveries of PAHs and to minimise the presence of interfering compounds in the last extract. In the case of SPE, Florisil cartridges of 1, 2 and 5 g, and silica cartridges of 5 g were studied. In that case, and with oysters and mussels, microwave-assisted extraction and 5 g Florisil cartridges provided good results. In addition, the concentrations obtained for Standard Reference Material (SRM) NIST 2977 (mussel tissue) were in good agreement with the certified values. In the case of microwave-assisted saponification, the extracts were not as clean as those obtained with 5 g Florisil and this fact lead to overestimate the concentration of the heaviest PAHs. Finally, the cleanest extracts were obtained by GPC. The method was successfully applied to mussels, oysters and hake liver, and the results obtained for NIST 2977 (mussel tissue) were within the confidence interval of the certified reference material for most of the certified analytes.

Temporal evolution of polycyclic aromatic hydrocarbons (PAHs) in sludge from wastewater treatment plants: comparison between PAHs and heavy metals

This paper presents results on the presence and temporal variability of the 16 PAHs recommended by the EPA in primary, secondary and digested sewage sludge over a year. The sewage sludges originated from the Guadalete wastewater treatment plant (WWTP) site in Jerez de la Frontera (Cádiz, Spain). These organic pollutants have been extracted from the sewage sludge by microwave energy. High performance liquid chromatography coupled with diode array (HPLC-DAD) or fluorescence (HPLC-FL) detectors have been used. The results showed that total PAHs concentration varied between 1,945 ng g(-1) dry matter (DM) for primary sludges collected in March and 10,100 ng g(-1) DM for primary sludge collected in June. Generally, concentrations of PAHs were higher in compost and digested sludge than in fresh one. On the other hand, the highest concentration of PAHs were found on summer. This thing is associated to the traffic increase from inland zones to the coast (Jerez de la Frontera is very near to beaches). Finally, this paper present a comparative study of the American an European legislation concluding that the limits of concentrations established are not exceeded. In addition heavy metals were analysed. The origin of PAHs and heavy metals seems to be different.

Optimization of a microwave-assisted extraction method for the analysis of polycyclic aromatic hydrocarbons from fish samples

A microwave-assisted extraction (MAE) procedure has been developed and optimized for the extraction of six regulated polycyclic aromatic hydrocarbons (PAHs) from muscle samples of polluted fish. The procedure involves the simultaneous microwave-assisted extraction of PAHs with n-hexane and the lipids hydrolysis with potassium hydroxide. Experimental design methodology allows a quick and robust optimization of operational parameters such as the extraction time, temperature, and solvent volumes. In these final optimized conditions, the procedure can be applied to a vast range of fat containing fish samples without significant changes, thus enabling its routine use. Recoveries around 90% for the studied compounds benz[a]anthracene, benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[a]pyrene, dibenz[a,h]anthracene, and indene[1,2,3-cd]pyrene and quantification limits (between 0.07 and 0.53 ng/g dry weight) far below the regulated limits, have been obtained. The procedure is applied to several different fish samples. Further, accuracy validation using NIST SRM 2977 reference material was carried out.