Rapid visual and spectrophotometric nitrite detection by cyclometalated ruthenium complex

Indopolycarbocyanine dyes as perspective analytical reagents for spectrophotometric determination of nitrite by radical nitration

A spectrophotometric method for the quantitative determination of nitrite was developed, based on the radical nitration of indopolycarbocyanine dyes in the presence of 2,2,6,6-tetramethylpiperidin-1-oxyl (TEMPO). The rate of the reaction of the studied dyes with nitrite increases with the lengthening of the polymethine chain and the presence of hydrophilic sulfo groups in the side chain of the dye. TEMPO acts as a co-reagent, significantly accelerating the reaction rate and increasing the sensitivity of nitrite determination. The proposed reaction mechanism is supported by spectrophotometric and HPLC/MS studies. For Ind2 (tetramethine indocarbocyanine cationic dye), the limit of detection for nitrite is 0.50 µM within a linearity range of 1-13 µM. The developed method is sensitive, with a LOD 130 times lower than the maximum contaminant level (MCL) of nitrite in drinking water (65 μM), as specified by the WHO. The method is of low-toxicity and good selectivity, as the determination of nitrite is not significantly affected by the main components of water. The method was successfully applied for the analysis of nitrite in natural and bottled water.

Technical Evaluation of a Paper-Based Electrochemical Strip to Measure Nitrite Ions in the Forensic Field

Nitrite is a compound used as a food additive for its preservative action and coloring capability, as well as an industrial agent for its antifreezing action and for preventing corrosion, and it is also used as a pharmaceutical in cyanide detoxification therapy. However, even recently, because of its high toxicity, it has been used as a murder and suicidal agent due to its affordability and ready availability. In this technical report, we describe an electrochemical paper-based device for selectively determining nitrite in complex biofluids, such as blood, cadaveric blood, vitreous humor, serum, plasma, and urine. The approach was validated in terms of the linearity of response, selectivity, and sensitivity, and the accuracy of the determination was verified by comparing the results with a chromatographic instrumental method. A linear response was observed in the micromolar range; the sensitivity of the method expressed as the limit of detection was 0.4 μM in buffer measurements. The simplicity of use, the portability of the device, and the performance shown make the approach suitable for detecting nitrite in complex biofluids, including contexts of forensic interest, such as murders or suicides in which nitrite is used as a toxic agent. Limits of detection of ca. 1, 2, 4, 5, 3, and 4 μM were obtained in vitreous humor, urine, serum and plasma, blood, and cadaveric blood, also highlighting a satisfactory accuracy comprised between 91 and 112%.

Advancements in Preprocessing and Analysis of Nitrite and Nitrate since 2010 in Biological Samples: A Review

As a substance present in organisms, nitrite is a metabolite of nitric oxide and can also be ingested. Nitrate is the metabolite of nitrite. Therefore, it is necessary to measure it quickly, easily and accurately to evaluate the health status of humans. Although there have been several reviews on analytical methods for non-biological samples, there have been no reviews focused on both sample preparation and analytical methods for biological samples. First, rapid and accurate nitrite measurement has significant effects on human health. Second, the detection of nitrite in biological samples is problematic due to its very low concentration and matrix interferences. Therefore, the pretreatment plus measuring methods for nitrite and nitrate obtained from biological samples since 2010 are summarized in the present review, and their prospects for the future are proposed. The treatment methods include liquid-liquid microextraction, various derivatization reactions, liquid-liquid extraction, protein precipitation, solid phase extraction, and cloud point extraction. Analytical methods include spectroscopic methods, paper-based analytical devices, ion chromatography, liquid chromatography, gas chromatography-mass spectrometry, electrochemical methods, liquid chromatography-mass spectrometry and capillary electrophoresis. Derivatization reagents with rapid quantitative reactions and advanced extraction methods with high enrichment efficiency are also included. Nitrate and nitrate should be determined at the same time by the same analytical method. In addition, much exploration has been performed on formulating fast testing through microfluidic technology. In this review, the newest developments in nitrite and nitrate processing are a focus in addition to novel techniques employed in such analyses.

Effects of Stocking Density on the Growth Performance, Physiological Parameters, Antioxidant Status and Lipid Metabolism of Pelteobagrus fulvidraco in the Integrated Rice-Fish Farming System

Pelteobagrus fulvidraco is a freshwater fish commonly raised in rice fields, yet the optimal stocking density for this species remains unknown. Therefore, this study aimed to investigate the appropriate stocking density of P. fulvidraco in integrated rice-fish farming systems. Three different stocking densities--low density (LD, 125 g/m2), middle density (MD, 187.5 g/m2), and high density (HD, 250 g/m2)--were set up to evaluate P. fulvidraco's growth performance, stress indices, immune function, antioxidant status, and lipid metabolism after 90 days of farming. The results indicated that HD treatment had a detrimental effect on P. fulvidraco's growth parameters. HD treatment led to an increase in cortisol (Cor) and lactate (La) levels, but a decrease in glucose (Glu) content in serum. After 90 days of farming, an immune response accompanied by the increase of complement 3 (C3), C4, and immunoglobulin M (IgM) was observed in the HD group. Meanwhile, HD treatment induced oxidative stress and altered antioxidative status evidenced by the levels of catalase (CAT), glutathione peroxidase (Gpx), glutathione (GSH), malondialdehyde (MDA), superoxide dismutase (SOD), and total antioxidant capacity (T-AOC) in serum or liver. Additionally, the lipid metabolism-related genes including lipoprotein lipase (lpl), peroxisome proliferators-activated receptor (pparα), carnitine palmitoyltransferase-1 (cpt-1), and sterol regulatory element binding protein-1 (srebp-1) were markedly downregulated in the HD and/or MD group after 90 days of farming. In conclusion, this study contributes to a better understanding of P. fulvidraco's response to different stocking densities in integrated rice-fish farming systems. We suggest that the appropriate stocking density for P. fulvidraco in these farming systems should be below 250 g/m2, considering both fish growth and physiological responses.

A cycloruthenated 2-phenylimidazole: chromogenic sensor for nitrite in acidic buffer and fluoride in CH3CN

A cycloruthenated 2-phenylimidazole as a colorimetric sensor can detect fluoride in CH3CN by a great red-shift in absorption. However, it demonstrated sensitivity and selectivity to nitrite rather than fluoride in acidic buffer.

Development of a simple analytical method for the determination of nitrite in waters using redox reaction and smartphone

In this study, it was aimed to perform the colorimetric determination of nitrite in waters using the redox reaction of iodide in acidic conditions with smartphone. The simple redox reaction of iodide and nitrite in an acidic medium was used instead of the conventional nitrite methods based on the formation of azo dye. The quantitative relationship between the yellow-colored iodine formed because of the reaction and nitrite was determined by the digital image-based colorimetric method (DIC). In the optimal experimental conditions, detection limit and R² values were determined as 0.02 mg/L and 0.9925, respectively. New method (Redox-DIC method) was validated by the standard Griess Method for nitrite in lake waters. The perfect recovery results (94-112%) were calculated for lake, river, tap, and spring waters spiked at different concentrations, and very good (< 5.0%) percent relative standard deviation values were recorded. Unlike conventional nitrite methods, organic reagents and solvents were not used in this method. The method is fast, simple, and low cost.

Intelligently design primary aromatic amines derived carbon dots for optical dual-mode and smartphone imaging detection of nitrite based on specific diazo coupling

Primary aromatic amines derived carbon dots (PAA-CDs) with the protonated amino groups and high quantum yield of 46% were favorably obtained by one-step solvothermal treatment of m-phenylenediamine (m-PDA) in acidic environment. The interaction between the PAA-CDs and nitrite (NO₂^-) was inherited the characteristic reaction of m-PDA (a primary aromatic amine) and NO₂^-, resulting in strong fluorescence quenching and obvious absorption variation of the PAA-CDs. Meanwhile, a chromogenic reaction of diazo coupling can cause significant color changes. Hence, the PAA-CDs were developed for an optical dual-mode and smartphone imaging sensor for NO₂^- detection in the range of 3.0 ~ 40.0 μM with high selectivity, good sensitivity, and excellent anti-interference capability. A limit of detection (LOD) of 0.024 μM and 0.16 μM was implemented by fluorometry and colorimetry, respectively. For smartphone imaging colorimetry, the LODs of 0.46 μM (visible color) and 0.99 μM (fluorescence color) were acquired. More importantly, the established sensor has been successfully applied for the dynamic detection of NO₂^- in various food samples with the satisfying results. A smartphone imaging colorimetry method based on the CDs was firstly proposed to visually and quantitatively detect NO₂^-, which will broaden the application range of the CDs in food safety inspection.

Electrochemical Sensing of Nitrite Ions Using Modified Electrode by Poly 1,8-Diaminonaphthalene/Functionalized Multi-Walled Carbon Nanotubes

A novel electrochemical sensor based on conducting polymer and multi-walled carbon nanotubes was reported for the detection of nitrite ions (NO₂⁻). The hybrid material poly 1,8-Diaminonaphthalene (poly 1,8-DAN)/functionalized multi-walled carbon nanotubes (f-MWCNT) was prepared by using a simple electrochemical approach which is based on the deposition of functionalized multi-walled carbon nanotubes (f-MWCNT) on the surface of the electrode followed by the electropolymerization of 1,8-DAN using cyclic voltammetry. The morphology and the electro-catalytic properties of the obtained electrodes were investigated with Fourier Transform Infrared Spectroscopy (FTIR), Transmission Electron Microscopy (TEM), Cyclic Voltammetry (CV), and Electrochemical Impedance Spectroscopy (EIS) showing an improvement of the electronic transfer due to the synergic effect between the proprieties of poly 1,8-DAN and f-MWCNT. Under the optimum experimental conditions, the poly 1,8-DAN/f-MWCNT/CPE exhibited excellent electro-catalytic activity towards nitrite detection. The nitrite anodic peak potential decreased by 210 mV compared to the bare carbon paste electrode. The calibration plot of nitrite detection was linear in the range of concentration from 300 to 6500 nM with a low detection limit of 75 nM.

Development of a simplified spectrophotometric method for nitrite determination in water samples

A new eco-friendly, rapid, and sensitive spectrophotometric method was developed to determine small quantities of nitrite, based on a diazotization mechanism. In an acidic solution, sulfathiazole was first diazotized with sodium nitrite, followed by adding phosphate buffer to form a yellow-colored compound, which showed maximum absorption at 450 nm, without the need for the addition of coupling agents such as N-(1-naphthyl) ethylenediamine. The effects of reagents amount and the optimal experimental conditions were examined by Central composite design. The simplified method presented a wide linear range of nitrite between 0.091 μg mL^-1 and 1.47 μg mL^-1, a sensitivity of 0.447 Abs mL µg^-1, a determination coefficient of 0.998, and a low limit of detection of 0.053 μg mL^-1. The simplified method was found to be comparable to the Griess method. It was evaluated for the measurements of nitrite using the accuracy profile approach. The validation procedure results established that 80% of the future results would be within the acceptability limit of 10% over the validation domain ranging from 0.174 μg mL^-1 to 1.37 μg mL^-1. The developed method was furtherly applied in the determination of nitrite using a developed paper-based analytical device that detected a nitrite concentration of 3 μg mL^-1 which is considered by the World Health Organization to be the maximal permissible limit of nitrite in drinking water.

Cyanine dye-assembled composite upconversion nanoparticles for the sensing and cell imaging of nitrite based on a single particle imaging method

An upconversion luminescence total internal reflection single particle imaging method was developed for the sensing and cell imaging of nitrite.

Ratiometric Colorimetric Detection of Nitrite Realized by Stringing Nanozyme Catalysis and Diazotization Together

Due to the great threat posed by excessive nitrite in food and drinking water to human health, it calls for developing reliable, convenient, and low-cost methods for nitrite detection. Herein, we string nanozyme catalysis and diazotization together and develop a ratiometric colorimetric approach for sensing nitrite in food. First, hollow MnFeO (a mixture of Mn and Fe oxides with different oxidation states) derived from a Mn-Fe Prussian blue analogue is explored as an oxidase mimic with high efficiency in catalyzing the colorless 3,3′,5,5′-tetramethylbenzidine (TMB) oxidation to blue TMBox, presenting a notable signal at 652 nm. Then, nitrite is able to trigger the diazotization of the product TMBox, not only decreasing the signal at 652 nm but also producing a new signal at 445 nm. Thus, the analyte-induced reverse changes of the two signals enable us to establish a ratiometric colorimetric assay for nitrite analysis. According to the above strategy, facile determination of nitrite in the range of 3.3–133.3 μM with good specificity was realized, providing a detection limit down to 0.2 μM. Compared with conventional single-signal analysis, our dual-signal ratiometric colorimetric mode was demonstrated to offer higher sensitivity, a lower detection limit, and better anti-interference ability against external detection environments. Practical applications of the approach in examining nitrite in food matrices were also verified.

A novel ratiometric and colorimetric probe for rapid and ultrasensitive detection of nitrite in water based on an Acenaphtho[1,2-d] imidazole derivative

The concentration of nitrite (NO₂^-) ions above allowable limits in water resources and food stuffs is considered hazardous and has been proven to be of great threat to the environment and public health. In this work, an acenaphtho [1,2-d] imidazole derivative (1) as a ratiometric colorimetric probe is developed. UV-Vis experiments demonstrate that the probe 1 shows excellent selectivity toward NO₂^- in the presence of other potential interfering species, a rapid response (20 s) and a low detection limit (100 nM) by a distinct visual color change with a bathochromic shift of 120 nm from colorless to intense yellow. Besides, this probe is further used for the quantification of nitrite ions in environmental water resources such as tap water, underground water, and surface water samples. The high recoveries (96-99% with relative standard deviations (RSD) of <2.0%) make the probe 1 a promising candidate for practical applications in daily life in the detection of nitrite ions.

First cycloruthenation of 2-alkenylpyridines: synthesis, characterization and properties

Several cyclometalated ruthenium complexes 1-5 with 2-alkenylpyridines as C,N-chelating ligands were synthesized and then characterized by NMR, MS, IR and UV-Vis spectra. According to the single crystal of complex 2, it is evident that carbon from vinyl group is successfully bonded to Ru(ii) center. Moreover, the Ru-N bond trans to the Ru-C bond is elongated (2.127(5) Å), which is consistent with the strong trans effect of the carbon atom compared to that of the nitrogen atom. With different electron-donating groups linked to vinyl, these complexes exhibited regular changes in MLCT absorption bands, which were identified by UV-Vis and CV spectra in combination with DFT and TD-DFT. Interestingly, protonated intermediate species of these complexes in acidic solutions were tracked by the absorption changes and MS spectra, which displayed a possible protonation process of these complexes with the cleavage of Ru-C σ bonds.

CdS/TiO2 Nanocomposite-Based Photoelectrochemical Sensor for a Sensitive Determination of Nitrite in Principle of Etching Reaction

The CdS/TiO₂ nanocomposite (NC) photoelectrochemical (PEC) sensor was constructed based on a new sensing strategy for nitrite assay. The CdS etching process caused by nitrite-in-acid solution was confirmed and applied to nitrite sensing. The CdS etching phenomenon occurring on the sensor led to an obvious reduction in the photocurrent response under visible-light irradiation, which responded to the nitrite concentration. The CdS/TiO₂ NC-based PEC sensor exhibited excellent performance on nitrite detection. The linear range for nitrite determination was from 1-100 and 100-500 μM, and the sensitivity of the PEC sensor was 2.91 and 0.186 μA μM^-1 cm^-2, respectively. The detection limit of the sensor was 0.56 μM (S/N = 3). In addition, the PEC sensor was also equipped with advantages such as good selectivity, excellent stability, low background, and recyclability. Satisfying results were obtained for the nitrite assay in real samples by such a PEC sensor. In summary, this work contributed a fresh idea to precisely determinate nitrite through PEC sensing.

Phenosafranin-Based Colorimetric-Sensing Platform for Nitrite Detection Enabled by Griess Assay

A facile and effective colorimetric-sensing platform based on the diazotization of phenosafranin for the detection of NO 2 - under acidic conditions using the Griess assay is presented. Diazotization of commercial phenosafranin produces a color change from purplish to blue, which enables colorimetric quantitative detection of NO 2 - . Optimal detection conditions were obtained at a phenosafranin concentration of 0.25 mM, HCl concentration of 0.4 M, and reaction time of 20 min. Under the optimized detection conditions, an excellent linearity range from 0 to 20 μM was obtained with a detection limit of 0.22 μM. Favorable reproducibility and selectivity of the colorimetric sensing platform toward NO 2 - were also verified. In addition, testing spiked ham sausage, bacon, and sprouts samples demonstrated its excellent practicability. The presented colorimetric sensing platform is a promising candidate for the detection of NO 2 - in real applications.

A highly sensitive and selective colorimetric probe based on a cycloruthenated complex: an Hg2+-promoted switch of thiophene coordination

A cyclometalated ruthenium complex [Ru(pthb)(bpy)2]+ (1, bpy = 2,2'-bipyridine, Hpthb = 3,3-dimethyl-2-(5-pyridylthiophen-2-yl)vinyl-benzo[e]indolium-1-propylsulfonate) could be converted from a C-coordinated structure to non-metallated species with N,S-bonded Hpthb upon treatment with mercury(ii) ions in water. Strikingly, the switch in the coordination mode resulted in a great absorption change along with a change in the solution color of 1 from dark red to light yellow. Therefore, 1 can be used as a colorimetric probe to detect mercury(ii) ions by the naked eye. Although the emission was not observed for 1 in water, it still demonstrated an appreciably low detection limit of 21 nM by using UV-Vis absorption spectroscopy, which was comparable with those of some probes determined by ratiometric fluorescence spectroscopy.

Fluorescent and colorimetric dual-readout sensor based on Griess assay for nitrite detection

In this work, we presented a sensitive and selective colorimetric and fluorescent dual-readout sensor based on Griess assay for nitrite (NO₂^-) detection under acidic condition. The sensor system was constituted of acid-resistant carbon quantum dots (CQDs) and 3-aminophenol (3-Aph) with acidic condition regulated using HCl. During the sensing procedure, reaction of 3-Aph and NO₂^- under acidic condition can yield a yellow-colored azoic compound (AZO), which gives the colorimetric readout; meanwhile, the fluorescence of CQDs (fluorescence reporter) quenched due to the strong absorption of AZO, leading to fluorescent readout. Wherein, CQDs were synthesized via hydrothermal method through using polyacrylamide as precursor and characterized by AFM, XRD and XPS. Under the optimized condition, the sensor exhibit broad linear relationships towards NO₂^- in the range of 10 to 100 nM and 2.5 to 100 μM, with practical detection limits of 10 nM and 2.5 μM for the fluorescent and colorimetric readout, respectively. And the sensor displayed excellent capability of selectivity according to interferences study. Furthermore, testing of sprouts, bacon and ham sausage real samples demonstrated good recoveries and reproducibility of the sensor system. All these results suggested the presented colorimetric and fluorescent dual-readout sensor can be a promising candidate for the NO₂^- detection in real applications.

Fluorometric determination of nitrite through its catalytic effect on the oxidation of iodide and subsequent etching of gold nanoclusters by free iodine

A method for sensitive detection of nitrite is presented. It is found that the red fluorescence of gold nanoclusters (with excitation/emission maxima at 365/635 nm) is quenched by traces of iodine via etching. Free iodide is formed by oxidation of iodide by bromate anion under the catalytic effect of nitrite. This catalytic process provides a sensitive means for nitrite detection. Under the optimal conditions, fluorescence linearly dropos in the 10 nM to 0.8 μM nitrite concentration range. The limit of detection is 1.1 nM. This is a few orders of magnitude lower than the maximum concentration allowed by authorities. Graphical abstract Schematic representation of a method for detection of nitrite via a redox reaction. Iodine was produced in the reaction and subsequently quenched the fluorescence from gold nanoclusters by etching their metallic cores, and a sensitive assay for nitrite down to 1.1 nM was developed.

Facile synthesis of highly porous CuO nanoplates (NPs) for ultrasensitive and highly selective nitrogen dioxide/nitrite sensing

Copper oxide (CuO) nanoplates (NPs of ∼100 nm width) were successfully synthesized via a chemical method (emulsion method). Superior catalytic activities towards both chemical and electrochemical sensing of nitrite were achieved.

Copper oxide (CuO) nanoplates (NPs of ∼100 nm width) have been successfully synthesized by using a chemical method (emulsion method). Superior catalytic activities towards both chemical and electrochemical sensing of nitrite were achieved.

Batch microfabrication and testing of a novel silicon-base miniaturized reference electrode with an ion-exchanging nanochannel array for nitrite determination

The reference electrode (RE) provides a stable potential for electrochemical detection; therefore, the RE plays an important role in environmental monitoring. In this paper, a novel batch of microfabricated silicon-base miniaturized Ag/AgCl RE was reported. A specially designed mini-tank for saturated KCl solution storage and a nanochannel array for ion-exchange were fabricated on a 4 inch (100) silicon wafer using a two-step KOH anisotropic etching process. An Ag/AgCl electrode was fabricated on a 4 inch Pyrex 7740 glass substrate. Finally, the finished silicon and glass substrates were anode bonded to form the entire system. By comparing with a conventional solid-state Ag/AgCl RE in electrochemical microsensors, a pre-packaged saturated KCl solution in the mini-tank provided a stable working environment for the Ag/AgCl electrode to ensure a constant reference potential. Compared with a routine glass-structured RE and by replacing the ion-exchange membrane with a nanochannel array, the miniaturized RE achieved a longer lifetime. The size of the finished miniaturized RE electrode was 11 mm × 14 mm. The reference potential variation was only 0.1 mV under continuous testing for 3000 s. The standard deviation in the reference potential was only 1.314 mV in different Na₂SO₄ buffer concentrations ranging from 3 mM to 30 mM. To verify the practicality of the novel silicon-base miniaturized RE, the fabricated RE was applied to measure the amount of nitrite in a water sample and achieved a better linearity of R² = 0.998. This miniaturized RE showed better reference potential stability and consistency because of the batch fabrication technique. This novel strategy for the design and manufacture of the miniaturized RE shows a bright future in the wide use of electrochemical sensors in online monitoring of water pollutants.

In this paper, a miniaturized Ag/AgCl reference electrode, which can be mass-produced by micro–nano manufacturing technology, was developed and demonstrated to have good stability and a long lifetime.

Highly integrated autonomous lab-on-a-chip device for on-line and in situ determination of environmental chemical parameters

The successful integration of sample pretreatment stages, sensors, actuators and electronics in microfluidic devices enables the attainment of complete micro total analysis systems, also known as lab-on-a-chip devices. In this work, we present a novel monolithic autonomous microanalyzer that integrates microfluidics, electronics, a highly sensitive photometric detection system and a sample pretreatment stage consisting on an embedded microcolumn, all in the same device, for on-line determination of relevant environmental parameters. The microcolumn can be filled/emptied with any resin or powder substrate whenever required, paving the way for its application to several analytical processes: separation, pre-concentration or ionic-exchange. To promote its autonomous operation, avoiding issues caused by bubbles in photometric detection systems, an efficient monolithic bubble removal structure was also integrated. To demonstrate its feasibility, the microanalyzer was successfully used to determine nitrate and nitrite in continuous flow conditions, providing real time and continuous information.