Novel nano-particles as fillers for an experimental resin-based restorative material

Fabrication and characterization of low-shrinkage dental composites containing montmorillonite nanoclay

Dental composites are aesthetic materials widely used in Dentistry for replacing hard dental tissues lost due to caries or traumas. The aim of this study was to fabricate low-shrinkage dental composite charged with nanoclay fillers (montmorillonite Cloisite®-MMT) and evaluate their cytotoxicity and physicomechanical properties. Four dental composites were produced from the same organic matrix: Bis-GMA/TEGDMA (30 wt.%). The filler system was constituted of BaSi, SiO₂, and MMT in the following concentrations (wt.%): 93.8/6.2/0, 89.1/5.9/5, 86.7/5.8/7.5, and 84.4/5.6/10 (E₀: 0; E₅: 5%; E_7.5: 7.5%; E₁₀: 10% of MMT nanoclays). The following properties were tested: in vitro cytotoxicity, flexural strength, elastic modulus, volumetric shrinkage, water sorption, water solubility, and hygroscopic expansion. Scanning electron microscopy was used to characterize composites' topography. Data were analyzed by one-way ANOVA and Tukey's HSD post hoc test (p < 0.05). MMT nanoclays did not affect the cytotoxicity. E₅ and E_7.5 groups showed a significant decrease in polymerization shrinkage while maintained the overall physicomechanical properties. The inclusion of 5 and 7.5 wt.% of MMT nanoclays allowed the fabrication of dental composites with low cytotoxicity and low polymerization shrinkage, without jeopardizing the overall behaviour of their physicomechanical properties (flexural strength, elastic modulus, water sorption, water solubility, and hygroscopic expansion). These aspects suggest that the usage of MMT nanoclays could be an effective strategy to formulate new dental composites with clinical applicability.

Shear Bond Strength of Composite and Ceromer Superstructures to Direct Laser Sintered and Ni-Cr-Based Infrastructures Treated with KTP, Nd:YAG, and Er:YAG Lasers: An Experimental Study

OBJECTIVE

The aim of this study was to examine the shear bond strength (SBS) of ceromer and nanohybrid composite to direct laser sintered (DLS) Cr-Co and Ni-Cr-based metal infrastructures treated with erbium-doped yttrium aluminum garnet (Er:YAG), neodymium-doped yttrium aluminum garnet (Nd:YAG), and potassium titanyl phosphate (KTP) laser modalities in in vitro settings.

METHODS

Experimental specimens had four sets (n = 32) including two DLS infrastructures with ceromer and nanohybrid composite superstructures and two Ni-Cr-based infrastructures with ceromer and nanohybrid composite superstructures. Of each infrastructure set, the specimens randomized into four treatment modalities (n = 8): no treatment (controls) and Er:YAG, Nd:YAG, and KTP lasers. The infrastructures were prepared in the final dimensions of 7 × 3 mm. Ceromer and nanohybrid composite was applied to the infrastructures after their surface treatments according to randomization. The SBS of specimens was measured to test the efficacy of surface treatments. Representative scanning electron microscopy (SEM) images after laser treatments were obtained.

RESULTS

Overall, in current experimental settings, Nd:YAG, KTP, and Er:YAG lasers, in order of efficacy, are effective to improve the bonding of ceromer and nanohybrid composite to the DLS and Ni-Cr-based infrastructures (p < 0.05). Nd:YAG laser is more effective in the DLS/ceromer infrastructures (p < 0.05). KTP laser, as second more effective preparation, is more effective in the DLS/ceromer infrastructures (p < 0.05). SEM findings presented moderate accordance with these findings.

CONCLUSIONS

The results of this study supported the bonding of ceromer and nanohybrid composite superstructures to the DLS and Ni-Cr-based infrastructures suggesting that laser modalities, in order of success, Nd:YAG, KTP, and Er:YAG, are effective to increase bonding of these structures.

Factors affecting marginal integrity of class II bulk-fill composite resin restorations

Background. Bulk-fill composite resins are a new type of resin-based composite resins, claimed to have the capacity to be placed in thick layers, up to 4 mm. This study was carried out to evaluate factors affecting gap formation in Cl II cavities restored using the bulk-fill technique.

Methods. A total of 60 third molars were used in this study. Two Cl II cavities were prepared in each tooth, one on the mesial aspect 1 mm coronal to the CEJ and one on the distal aspect 1 mm apical to the CEJ. The teeth were divided into 4 groups: A: The cavities were restored using the bulk-fill technique with Filtek P90 composite resin and its adhesive system and light-cured with quartz tungsten halogen (QTH) light-curing unit. B: The cavities were restored similar to that in group A but light-cured with an LED light-curing unit. C: The cavities were restored using the bulk-fill technique with X-tra Fil composite resin and Clearfil SE Bond adhesive system and light-cured with a QTH curing unit. D: The cavities were restored similar to that in group C but light-cured with an LED light-curing unit. The gaps were examined under a stereomicroscope at ×60. Data were analyzed with General Linear Model test. In cases of statistical significance (P<0.05), post hoc Bonferroni test was used for further analyses.

Results. The light-curing unit type had no effect on gap formation. However, the results were significant in relation to the composite resin type and margin location (P<0.001). The cumulative effects of light-curing unit*gingival margin and light-curing unit*composite resin type were not significant; however, the cumulative effect of composite rein type*gingival margin was significant (P=0.04)

Conclusion. X-tra Fil composite exhibited smaller gaps compared with Filtek P90 composite with both light-curing units. Both composite resins exhibited smaller gaps at enamel margins.

Color Stability and Surface Roughness of Composite submitted to Different Types and Periods of Finishing/Polishing: Physical Properties of Composites

AIM

The aim of this study was to evaluate the influence of accelerated artificial aging (AAA) on color stability (AE) and surface roughness of composite submitted to different systems and periods of finishing/polishing.

MATERIALS AND METHODS

A Teflon matrix was used to fabricate 60 specimens that were separated into four groups, according to the finishing/polishing system: G1: no polishing; G2: abrasive papers; G3: rubber polishing disks; and G4: G2 + G3. Polishing was performed at three different time intervals (n = 6): immediately (Im), 24 hours (24 hours) and 7 days (7 day) after specimen fabrication. Initial color and surface roughness readouts were taken. Afterwards, specimens were submitted to AAA (480 hours) and new readouts were taken.

RESULTS

Results demonstrated that G2 (7 day) presented lower AE, statistically different from G1 and G4 (7 days) (two-way analysis of variance (ANOVA), Bonferroni, p < 0.05).

CONCLUSION

Regarding roughness, there was no difference among groups and periods. Polishing performed with abrasive papers, 7 days after performing the restoration, promoted less color alteration.

CLINICAL SIGNIFICANCE

Most of composite restorations are replaced within a period shorter than 5 years due to esthetic failure, and correct finishing and polishing procedures are fundamental to avoid these problems.

Review of nanomaterials in dentistry: interactions with the oral microenvironment, clinical applications, hazards, and benefits

Interest in the use of engineered nanomaterials (ENMs) as either nanomedicines or dental materials/devices in clinical dentistry is growing. This review aims to detail the ultrafine structure, chemical composition, and reactivity of dental tissues in the context of interactions with ENMs, including the saliva, pellicle layer, and oral biofilm; then describes the applications of ENMs in dentistry in context with beneficial clinical outcomes versus potential risks. The flow rate and quality of saliva are likely to influence the behavior of ENMs in the oral cavity, but how the protein corona formed on the ENMs will alter bioavailability, or interact with the structure and proteins of the pellicle layer, as well as microbes in the biofilm, remains unclear. The tooth enamel is a dense crystalline structure that is likely to act as a barrier to ENM penetration, but underlying dentinal tubules are not. Consequently, ENMs may be used to strengthen dentine or regenerate pulp tissue. ENMs have dental applications as antibacterials for infection control, as nanofillers to improve the mechanical and bioactive properties of restoration materials, and as novel coatings on dental implants. Dentifrices and some related personal care products are already available for oral health applications. Overall, the clinical benefits generally outweigh the hazards of using ENMs in the oral cavity, and the latter should not prevent the responsible innovation of nanotechnology in dentistry. However, the clinical safety regulations for dental materials have not been specifically updated for ENMs, and some guidance on occupational health for practitioners is also needed. Knowledge gaps for future research include the formation of protein corona in the oral cavity, ENM diffusion through clinically relevant biofilms, and mechanistic investigations on how ENMs strengthen the tooth structure.

The first study of surface modified silica nanoparticles in pressure-decreasing application

Hydrophobic silica nanoparticles were prepared through surface modification of silica nanoparticles by (dimethyldichlorosilane) DMCS for pressure-decreasing in oilfield.

Influence of Silica and Zirconia Particles as Filler Loading on the Radiopacity of Dental Resin Composites

The aim of this study is to evaluate the radiopacity of silica (SiO2) and zirconia (ZrO2) particles dispersed in a bisphenol-a-glycidyl methacrylate (Bis-GMA) as a base resin and triethylene glycol dimethacrylate (TEGDMA) as a diluent. The fillers were mixed separately with bis-GMA/TEGDMA monomers, in proportions of 40, 50 and 60 wt.%. A resin matrix containing 0 wt.% filler was used as the control composition to evaluate the effect of filler loading on the radiopacity. Samples of the composites with 2.5 mm thickness were compared their radiopacity with the same thickness of the standard aluminum plate. The radiopacity of both resin matrix/SiO2and resin matrix/ZrO2composites increased gradually as the filler loading increased. The resin matrix/ZrO2composites possessed radiopacity higher than the standard aluminum plate. The increase of filler loading showed highly significant differences in the radiopacity as tested by ANOVA (P= 0.000).

Influence of nanometer scale particulate fillers on some properties of microfilled composite resin

The aim of this study was to evaluate the effect of different weight fractions of nanometer sized particulate filler on properties of microfilled composite resin. Composite resin was prepared by mixing 33 wt% of resin matrix to the 67 wt% of silane treated microfine silica particulate fillers with various fractions of nanometer sized fillers (0, 10, 15, 20, 30 wt%) using a high speed mixing machine. Test specimens made of the composites were tested with a three-point bending test with a speed of 1.0 mm/min until fracture. Surface microhardess (Vicker's microhardness) was also determined. The volumetric shrinkage in percent was calculated as a buoyancy change in distilled water by means of the Archimedes principle. The degree of monomer conversion (DC%) of the experimental composites containing different nanofiller fractions was measured using FTIR spectroscopy. Surface roughness (Ra) was determined using a surface profilometer. Nanowear measurements were carried out using a nanoindentation device. The water uptake of specimens was also measured. Parameters were statistically analysed by ANOVA (P < 0.05). The group without nanofillers showed the highest flexural strength and modulus, DC% and Ra value. The group with 30% nanofillers had the highest water uptake and volumetric shrinkage. No significant difference was found in Vicker's microhardness and the nanowear of the composites. The plain microfilled composite demonstrated superior properties compared to the composites loaded with nanofillers with the exception of surface roughness.

Kinetic study of free radicals trapped in dental resins stored in different environments

In this work, we used electron paramagnetic resonance to follow the decrease kinetics of free radicals trapped in an experimental resin (ER) and in a commercial composite (Charisma (Ch)) stored under different conditions (in air at 25 and 37 degrees C; in argon, oxygen and water at 25 degrees C). During the first day, the decay was fast (0-24h-rate of decay of allylic radical: 1700-1000a.u. for Ch, 1700-1500a.u. for ER) and the storage conditions had no influence on the kinetics. This phase was ascribed to a post-polymerization phenomenon. From 1day to 1month, the rate of decay depended on the storage environment. In argon, free radicals were quite stable (1day to 1month-rate of decay of allylic radical: 1200-1000a.u. for Ch, 1400-1200a.u. for ER). For the other storage environments, in ER, the rate of decay was higher in water than in oxygen and in air (1day to 1month-rate of decay of allyl radical: 1400a.u. to 100, 500 and 800a.u., respectively). In Ch, free radicals faded quicker than in ER, as undetectable levels were reached before 1month, which attests to the influence of fillers on radical decrease kinetics. Heating experiments were also performed, and free radical concentrations decreased faster at higher temperatures, especially above the glass transition temperature. In conclusion, ambient oxygen is mainly involved in the termination process of free radicals. Therefore, conditions influencing oxygen diffusion have an impact on radical kinetics as well.

Characterization of water sorption, solubility and filler particles of light-cured composite resins

The goals of this study were to measure the water sorption (WS) and solubility (SO) of 3 composite resins containing different filler contents. Additionally, the size, shape, type and other characteristics of fillers were analyzed by scanning electron microscopy (SEM). Three composites, classified according to filler size, were selected: Filtek Supreme nanofill (3M/ESPE), Esthet-X minifill (Dentsply/Caulk) and Renamel microfill (Cosmedent Inc.). Ten disk-shaped specimens of each resin composite were made and stored in desiccators until constant mass was achieved. Specimens were then stored in water for 7 days, and the mass of each specimen was measured. The specimens were dried again and dried specimen mass determined. The WS and SO were calculated from these measurements. Data analyzed by one-way ANOVA and Tukey's post-hoc test (?=0.05). Composite filler particles were observed under SEM after removal of resin matrix by organic solvents. WS values were not significantly different among the resins; however, SO values were lower for Filtek Supreme. The materials presented differences in filler contents (e.g. particle size and shape). The composite resins had similar WS, while the SO was lower for the nanofill than for mini and microfill resins. The filler characteristics varied and were different among the materials.