Degradation in the dentin-composite interface subjected to multi-species biofilm challenges

Synergistic effects of bacteria, enzymes, and cyclic mechanical stresses on the bond strength of composite restorations

Predicting how tooth and dental material bonds perform in the mouth requires a deep understanding of degrading factors. Yet, this understanding is incomplete, leading to significant uncertainties in designing and evaluating new dental adhesives. The durability of dental bonding interfaces in the oral microenvironment is compromised by bacterial acids, salivary enzymes, and masticatory fatigue. These factors degrade the bond between dental resins and tooth surfaces, making the strength of these bonds difficult to predict. Traditionally studied separately, a combined kinetic analysis of these interactions could enhance our understanding and improvement of dental adhesive durability. To address this issue, we developed and validated an original model to evaluate the bond strength of dental restorations using realistic environments that consider the different mechanical, chemical, and biological degradative challenges working simultaneously: bacteria, salivary esterases, and cyclic loading. We herein describe a comprehensive investigation on dissociating the factors that degrade the bond strength of dental restorations. Our results showed that cariogenic bacteria are the number one factor contributing to the degradation of the bonded interface, followed by cyclic loading and salivary esterases. When tested in combinatorial mode, negative and positive synergies towards the degradation of the interface were observed. Masticatory loads (i.e., cycling loading) enhanced the lactic acid bacterial production and the area occupied by the biofilm at the bonding interface, resulting in more damage at the interface and a reduction of 73 % in bond strength compared to no-degraded samples. Salivary enzymes also produced bond degradation caused by changes in the chemical composition of the resin/adhesive. However, the degradation rates are slowed compared to the bacteria and cyclic loading. These results demonstrate that our synergetic model could guide the design of new dental adhesives for biological applications without laborious trial-and-error experimentation.

Compression Behavior of Dental Flowable Composites-Digital Image Correlation and Numerical Analysis

In the development of restorative materials, it is important to evaluate the elastic properties of the material in order to achieve good clinical results. The aim of this study was to evaluate the compression behavior of two dental flowable materials (EverX Flow and Flow-Art) using experimental methods and numerical simulation. The Poisson's ratio was determined using two methods of strain measurement: the electrical strain gauge method (ESG) and digital image correlation (DIC). Material constants determined in experimental studies were implemented in a numerical model, and displacement analysis was conducted using the finite element method (FEM). The tests showed higher compressive strength and modulus of elasticity for EverX Flow compared to Flow-Art. The values of the Poisson's ratio were similar for both measurement methods, ranging from 0.27 to 0.28 for EverX Flow and from 0.30 to 0.32 for Flow-Art. This demonstrated the feasibility of the DIC method for obtaining the Poisson's ratio values for this type of composites. Compression test conditions were reproduced in the numerical analysis. The obtained distributions of the displacement field on the surface of the sample from the DIC and numerical analyses were compared. A good match was observed between DIC displacement measurements and displacement values obtained in FEM analysis. The comprehensive approach used in the study allows us to analyze whether the results obtained in the numerical simulation correspond to the material response to the applied load and validate the model.

Post-failure analysis of model resin-composite restorations subjected to different chemomechanical challenges

OBJECTIVE

The current study aimed to evaluate the effects of different combinations of chemical and mechanical challenges on the failure load, failure mode and composition of the resulting fracture surfaces of resin-composite restorations.

METHODS

Three resin composites were used to fill dentin disks (2 mm inner diameter, 5 mm outer diameter, and 2 mm thick) made from bovine incisor roots. The model restorations, half of which were preconditioned with a low-pH buffer (48 h under pH 4.5), were subjected to diametral compression with either a monotonically increasing load (fast fracture) or a cyclic load with a continuously increasing amplitude (accelerated fatigue). The load or number of cycles to failure was noted. SEM was performed on the fracture surfaces to determine the proportions of dentin, adhesive, and resin composite.

RESULTS

Both cyclic fatigue and acid preconditioning significantly reduced the failure load and increased the proportion of interfacial failure in almost all the cases, with cyclic fatigue having a more pronounced effect. Cyclic fatigue also increased the amount of adhesive/hybrid layer present on the fracture surfaces, but the effect of acid preconditioning on the composition of the fracture surfaces varied among the resin composites.

SIGNIFICANCE

The adhesive or hybrid layer was found to be the least resistant against the chemomechanical challenges among the components forming the model restoration. Increasing such resistance of the tooth-restoration interface, or its ability to combat the bacterial actions that lead to secondary caries following interfacial debonding, can enhance the longevity of resin-composite restorations.

Synergistic enhancement of hydrophobic dental adhesives: autonomous strengthening, polymerization kinetics, and hydrolytic resistance

The leading cause of composite restoration failure is recurrent marginal decay. The margin between the composite and tooth is initially sealed by a low-viscosity adhesive, but chemical, physical, and mechanical stresses work synergistically and simultaneously to degrade the adhesive, destroying the interfacial seal and providing an ideal environment for bacteria to proliferate. Our group has been developing self-strengthening adhesives with improved chemical and mechanical characteristics. This paper reports a self-strengthening adhesive formulation that resists hydrolysis-mediated degradation by providing intrinsic reinforcement of the polymer network through synergistic stimulation of free-radical polymerization, sol-gel reaction, and hydrophobicity. Hydrophobic resin formulation (NE1) was developed using HEMA/BisGMA 28/55w/w and 15 wt% MPS. Control (NC1) contained HEMA/BisGMA 28/55 w/w and 15 wt% MES. The polymerization kinetics, water sorption, leachates, and dynamic mechanical properties of the resin samples were investigated. The NC1 and NE1 samples showed comparable polymerization kinetics, degree of conversion and water sorption. In contrast, NC1 showed significantly higher levels of HEMA and BisGMA leachate, indicating faster degradation in ethanol. At day 3, cumulative HEMA leachate for NC1 was tenfold greater than NE1 (p < 0.05). Dynamic mechanical properties were measured at 37 and 70°C in both dry and wet conditions. Under dry conditions, the storage moduli of NC1 and NE1 were comparable and the glass transition temperature (T g) of NC1 was statistically significant lower (p < 0.001) than NE1. Under wet conditions, the storage modulus of NC1 was lower than NE1 and at 70°C there is a threefold difference in storage modulus. At this temperature and under wet conditions, the storage modulus of NC1 is statistically significantly lower (p < 0.001) than NE1. The results indicated that in the wet environment, NE1 provided lower chain mobility, higher crosslink density, and more hydrogen bonds. The newly formulated methacrylate-based adhesive capitalizes on free-radical polymerization, sol-gel reactions, and hydrophobicity to provide enhanced mechanical properties at elevated temperatures in wet environments and hydrolytic stability under aggressive aging conditions.

An in vitro dynamic bioreactor model for evaluating antimicrobial effectiveness on periodontal polymicrobial biofilms: a proof-of-concept study

BACKGROUND

The aim of this study was to investigate an in vitro dynamic bioreactor model by evaluating the antimicrobial effect of clinically relevant amoxicillin doses on polymicrobial microcosm biofilms derived from subgingival plaque.

METHODS

Biofilms from pooled subgingival plaque were grown for 108  hours in control and experimental dynamic biofilm reactors. Amoxicillin was subsequently infused into the experimental reactor to simulate the pharmacokinetic profile of a standard 500 mg thrice-daily dosing regimen over 5 days and biofilms were assessed by live/dead staining, scanning electron microscopy, and quantitative polymerase chain reaction.

RESULTS

Following establishment of the oral microcosm biofilms, confocal imaging analysis showed a significant increase in dead bacteria at 8 hours (p = 0.0095), 48 hours (p = 0.0070), 96 hours (p = 0.0140), and 120 hours (p < 0.0001) in the amoxicillin-treated biofilms compared to the control biofilms. Nevertheless, viable bacteria remained in the center of the biofilm at all timepoints. Significant reductions/elimination in Campylobacter rectus, Tannerella forsythia, Aggregatibacter actinomycetemcomitans, and Peptostreptococcus anaerobius was observed among the amoxicillin-treated biofilms at the 96 and 120 hour timepoints.

CONCLUSION

A novel in vitro dynamic model of oral microcosm biofilms was effective in modeling the antimicrobial effect of a pharmacokinetically simulated clinically relevant dose of amoxicillin.

Antibiofilm and antimicrobial activity of temporary filling materials on root canals: an in situ acid challenge

The present study evaluated the antibiofilm and antimicrobial effects of temporary restorative materials on root canals after an intra-oral challenge. Seventy roots were endodontically treated and divided into 5 groups: high-viscosity glass ionomer (HV-GIC), light-activated glass ionomer (RM-GIC), zinc-oxide cement without eugenol (ZO), zinc-oxide cement with eugenol (ZOE), and unsealed roots (negative control). For 28 days, 14 participants used intra-oral devices with five roots, and drops of sucrose were applied onto them. The amount of biofilm and the bacterial counts were analyzed by Kruskal-Wallis and Dunn, and by two-way ANOVA and Tukey (α = 0.05). HV-GIC and RM-GIC better inhibit biofilm, followed by ZO and ZOE. Unsealed roots had the largest biofilm accumulation (p = 0.002) and higher bacterial penetration than restored roots (p = 0.023). A low amount of Streptococcus was found in RM-GIC and ZOE-restored roots without difference from HV-GIC (p = 0.021). The low amount of Enterococcus (p = 0.003) was found in the ZOE-restored roots, without difference from GICs.

Recurrent caries models to assess dental restorations: A scoping review

OBJECTIVES

To review the literature on recurrent caries models used to evaluate restorative materials, compare reported methodology and parameters, and devise specific recommendations to be considered in future investigations.

DATA

The following were extracted: study design, sample characteristics, source of teeth, name of restorations compared including controls, recurrent caries model type, type of demineralizing and remineralizing solutions, type of biofilm used, methods to detect recurrent caries.

SOURCES

Literature searches were performed in OVID Medline, EMBASE, SCOPUS, and Cochrane Library.

STUDY SELECTION

For a study to be included, it had to examine dental materials for tooth restoration purposes only with a valid control group and evaluate restorative dental materials regardless of the form of the teeth caries model used or nature of the tooth structure used. A total of 91 studies were included. Most of the studies presented were in vitro. Human teeth were the main source of specimens utilized. Around 88% of the studies used specimens without an artificial gap, and 44% used a chemical model. S. mutans was the main bacterial species used in microbial caries models.

CONCLUSION

The findings of this review provided an insight into the performance of available dental materials assessed using different recurrent caries models, yet this review cannot be used as a guideline for material selection. Selecting the appropriate restorative material relies on several patient-related factors such as microbiota, occlusion, and diet that are not comprehensively taken into consideration in recurrent caries models and thus hinder reliable comparison.

CLINICAL SIGNIFICANCE

Due to the heterogenicity of variables among studies on the performance of dental restorative materials, this scoping review aimed to provide insights for dental researchers concerning the available recurrent caries models, testing methods used, and aspects of comparison between these materials including their characteristics and limitations.

Biofilm Formation on the Surfaces of CAD/CAM Dental Polymers

Dental polymers are now available as monolithic materials which can be readily used in computer-aided design and computer-aided manufacturing (CAD/CAM) systems. Despite possessing numerous advantages over conventionally produced polymers, the polymers produced by either of these systems fail to exhibit immunity to surface microbial adhesion when introduced into the oral environment, leading to the development of oral diseases. The aim of this study was to analyze the biofilm formation of six microorganisms from the oral cavity and its correlation to the surface characteristics of CAD/CAM dental polymers. A total of ninety specimens were divided into three groups: resin-based composite, polymethyl methacrylate, and polyether ether ketone. The experimental procedure included surface roughness and water contact angle measurements, colony forming unit counting, and scanning electron microscopy analysis of biofilm formed on the surface of the tested materials. The data were analyzed using the Kruskal-Wallis test, with a Dunn's post hoc analysis, and one way analysis of variance, with a Tukey's post hoc test; the correlation between the measurements was tested using Spearman's correlation coefficient, and descriptive statistics were used to present the data. Despite using the same manufacturing procedure, as well as the identical manufacturer's finishing and polishing protocols, CAD/CAM dental polymers revealed significant differences in surface roughness and water contact angle, and the increased values of both parameters led to an increase in biofilm formation on the surface of the materials. The CAD/CAM resin-based composite showed the lowest number of adhered microorganisms compared to CAD/CAM polymethyl methacrylate and CAD/CAM polyether ether ketone.

Novel bioactive dental restorations to inhibit secondary caries in enamel and dentin under oral biofilms

OBJECTIVE

To provide the first review on cutting-edge research on the development of new bioactive restorations to inhibit secondary caries in enamel and dentin under biofilms. State-of-the-art bioactive and therapeutic materials design, structure-property relationships, performance and efficacies in oral biofilm models.

DATA, SOURCES AND STUDY SELECTION

Researches on development and assessment new secondary caries inhibition restorations via in vitro and in vivo biofilm-based secondary caries models were included. The search of articles was carried out in Web of Science, PubMed, Medline and Scopus.

CONCLUSIONS

Based on the found articles, novel bioactive materials are divided into different categories according to their remineralization and antibacterial biofunctions. In vitro and in vivo biofilm-based secondary caries models are effective way of evaluating the materials efficacies. However, new intelligent and pH-responsive materials were still urgent need. And the materials evaluation should be performed via more clinical relevant biofilm-based secondary caries models.

CLINICAL SIGNIFICANCE

Secondary caries is a primary reason for dental restoration failures. Biofilms produce acids, causing demineralization and secondary caries. To inhibit dental caries and improve the health and quality of life for millions of people, it is necessary to summarize the present state of technologies and new advances in dental biomaterials for preventing secondary caries and protecting tooth structures against oral biofilm attacks. In addition, suggestions for future studies are provided.

Antibiofilm properties of silver nanoparticles incorporated into polymethyl methacrylate used for dental applications

BACKGROUND

Acrylic resins used in dental and biomedical applications do not have antimicrobial properties, their surface is susceptible to colonization of microorganisms.

OBJECTIVE

The aim of this study was to evaluate the antibiofilm properties of silver nanoparticles (AgNPs) deposited in a polymethyl methacrylate (PMMA) surface against a Staphylococcus aureus biofilm.

METHODS

The PMMA was impregnated with AgNPs by using the in-situ polymerization method. To determine the solubility of the incorporated silver (Ag+) atomic absorption spectrophotometry was used (AAS) at 24 h, 48 h, 7 days, and 30 days. Thirty specimens of PMMA with AgNPs and without NP (control group) were assembled in the CDC Biofilm Bioreactor system with a cell suspension of S. aureus. The specimens were removed at 6, 12, 24, 48, and 72 h to determine the viability profile and quantify the Arbitrary Fluorescence Units (AFU).

RESULTS

The AgNPs showed an irregular and quasispherical shape with an average size of 25 nm. AAS analysis demonstrated a low solubility of Ag+. The formation of the S. aureus biofilm increased as the evaluation periods continued up to 72 h. The experimental group showed poor growth, and a decrease in the intensity of the fluorescence demonstrated a statistically significant inhibition of the formation of the biofilm (P < 0.05) in relation to the control group at 6, 12, 24, 48, and 72 h.

CONCLUSION

AgNPs incorporated into PMMA decreased the growth and maturation of S. aureus biofilm.

Accelerated Fatigue Model for Predicting Composite Restoration Failure

An empirical method is proposed to predict the clinical performance of resin composite dental restorations by using laboratory data derived from simple specimens subjected to chemical degradation and accelerated cyclic fatigue. Three resin composites were used to fill dentin disks (2-mm inner diameter, 5-mm outer diameter, and 2 mm thick) made from bovine incisor roots. The specimens (n = 30 per group) were aged with different durations of a low-pH challenge (0, 24, and 48 h under pH 4.5) before being subjected to diametral compression with either a monotonically increasing load (fast fracture) or a cyclic load with a continuously increasing amplitude (accelerated fatigue). The data from 1 material were used to establish the relationship between laboratory time (number of cycles) and clinical time to failure (years) via the respective survival probability curves. The temporal relationship was then used to predict the clinical rates of failure for restorations made of the other 2 materials, and the predictions were compared with the clinical data to assess their accuracy. Although there were significant differences in the fast fracture strength among the groups of materials or durations of chemical challenge, fatigue testing was much better at separating the groups. Linear relationships were found between the laboratory and clinical times to failure for the first material (R2 = 0.90, 0.90, and 0.62 for the 0-, 24-, and 48-h low-pH groups, respectively). The clinical life of restorations made of the other 2 materials was best predicted with data from the 48-h low-pH groups. In conclusion, an accelerated fatigue model was successfully calibrated and applied to predict the clinical failure of resin composite restorations, and the predictions based on data obtained from chemically aged specimens provided the best agreement with clinical data.

In Search of Novel Degradation-Resistant Monomers for Adhesive Dentistry: A Systematic Review and Meta-Analysis

This study aimed to assess whether degradation-resistant monomers included in experimental dental adhesives can improve long-term bond strength compared to conventional monomers. This study followed the latest PRISMA guidance (2020). The search for the systematic review was carried out in four electronic databases: PubMed/Medline, Scopus, SciELO and EMBASE, without restrictions on the year of publication and language. The last screening was conducted in July 2022. Interventions included were in vitro studies on experimental dental adhesives that tested short-term and long-term bond strength, but also water sorption and solubility data when available, in extracted human molars. Meta-analyses were performed using Rstudio v1.4.1106. A summary table analyzing the individual risk of bias was generated using the recent RoBDEMAT tool. Of the 177 potentially eligible studies, a total of 7 studies were included. Experimental monomers with acrylamides or methacrylamide−acrylamide hybrids in their composition showed better results of aged bond strength when compared to methacrylate controls (p < 0.05). The experimental monomers found better sorption and solubility compared to controls and were significantly different (p < 0.001). It is possible to achieve hydrolytically resistant formulations by adding novel experimental monomers, with chemical structures that bring benefit to degradation mechanisms.

Multispecies biofilm removal by a multisonic irrigation system in mandibular molars

AIM

The aim of the study was to assess biofilm removal efficacy of GentleWave System and passive ultrasonic irrigation (PUI).

METHODOLOGY

Twenty-two human mandibular molars with Vertucci's type II configuration in the mesial root were selected. Teeth were autoclaved, inoculated with dental plaque and incubated in a CDC biofilm reactor for two weeks. The mesial roots were instrumented up to 20.06 file (V-Taper) for the GentleWave group and up to 35.04 file (Vortex Blue) for PUI group. Irrigation was performed using GentleWave and PUI irrigation protocols (n = 11). Dentine debris on paper points samples were obtained for quantitative real-time polymerase chain reaction (qPCR) and 16S ribosomal RNA gene sequencing (next-generation aequencing-NGS). For qPCR, a non-parametric test (α = 0.05) was used. Next-generation sequencing data were analysed using mothur, with alpha diversity calculated as the Shannon and Chao1 indices and Bray-Curtis dissimilarities were used for beta diversity. Differences in alpha diversity and abundances of genera were evaluated using Kruskal-Wallis test. Differences in community composition were evaluated using analysis of similarity with Bonferroni correction for multiple comparisons.

RESULTS

Quantitative real-time polymerase chain reaction results showed that the reduction estimated in percentages for both groups was equivalent (p > .05). NGS analysis showed that both techniques promoted a significant reduction in reads and OTUs number (p < .05). Shannon alpha diversity and Chao1 index showed no differences between pre- or post-treatment samples for both groups (p > .05). Additionally, pre-treatment communities differed from post-treatment samples in both groups regarding bacterial taxa reduction (ANOSIM R = 0.50 and 0.55, p < .001).

CONCLUSIONS

Bacterial reduction in mesial roots of mandibular molars prepared to 35.04 with PUI was similar to those prepared to 20.06 with a multisonic irrigant activation system.

In-vitro models of biocompatibility testing for restorative dental materials: From 2D cultures to organs on-a-chip

Dental caries is a biofilm-mediated, diet-modulated, multifactorial and dynamic disease that affects more than 90% of adults in Western countries. The current treatment for decayed tissue is based on using materials to replace the lost enamel or dentin. More than 500 million dental restorations are placed annually worldwide, and materials used for these purposes either directly or indirectly interact with dentin and pulp tissues. The development and understanding of the effects of restorative dental materials are based on different in-vitro and in-vivo tests, which have been evolving with time. In this review, we first discuss the characteristics of the tooth and the dentin-pulp interface that are unique for materials testing. Subsequently, we discuss frequently used in-vitro tests to evaluate the biocompatibility of dental materials commonly used for restorative procedures. Finally, we present our perspective on the future directions for biological research on dental materials using tissue engineering and organs on-a-chip approaches. STATEMENT OF SIGNIFICANCE: Dental caries is still the most prevalent infectious disease globally, requiring more than 500 million restorations to be placed every year. Regrettably, the failure rates of such restorations are still high. Those rates are partially based on the fact that current platforms to test dental materials are somewhat inaccurate in reproducing critical components of the complex oral microenvironment. Thus, there is a collective effort to develop new materials while evolving the platforms to test them. In this context, the present review critically discusses in-vitro models used to evaluate the biocompatibility of restorative dental materials and brings a perspective on future directions for tissue-engineered and organs-on-a-chip platforms for testing new dental materials.

Autonomous-Strengthening Adhesive Provides Hydrolysis-Resistance and Enhanced Mechanical Properties in Wet Conditions

The low-viscosity adhesive that is used to bond composite restorative materials to the tooth is readily damaged by acids, enzymes, and oral fluids. Bacteria infiltrate the resulting gaps at the composite/tooth interface, demineralize the tooth, and further erode the adhesive. This paper presents the preparation and characterization of a low-crosslink-density hydrophilic adhesive that capitalizes on sol-gel reactions and free-radical polymerization to resist hydrolysis and provide enhanced mechanical properties in wet environments. Polymerization behavior, water sorption, and leachates were investigated. Dynamic mechanical analyses (DMA) were conducted using water-saturated adhesives to mimic load transfer in wet conditions. Data from all tests were analyzed using appropriate statistical tests (α = 0.05). The degree of conversion was comparable for experimental and control adhesives at 88.3 and 84.3%, respectively. HEMA leachate was significantly lower for the experimental (2.9 wt%) compared to control (7.2 wt%). After 3 days of aqueous aging, the storage and rubbery moduli and the glass transition temperature of the experimental adhesive (57.5MPa, 12.8MPa, and 38.7 °C, respectively) were significantly higher than control (7.4MPa, 4.3 MPa, and 25.9 °C, respectively). The results indicated that the autonomic sol-gel reaction continues in the wet environment, leading to intrinsic reinforcement of the polymer network, improved hydrolytic stability, and enhanced mechanical properties.

In vitro physicochemical characterization of five root canal sealers and their influence on an ex vivo oral multi-species biofilm community

AIM

To evaluate the physicochemical properties of five root canal sealers and assess their effect on an ex vivo dental plaque-derived polymicrobial community.

METHODOLOGY

Dental plaque-derived microbial communities were exposed to the sealers (AH Plus [AHP], GuttaFlow Bioseal [GFB], Endoseal MTA [ESM], Bio-C sealer [BCS] and BioRoot RCS [BRR]) for 3, 6 and 18 h. The sealers' effect on the biofilm biomass and metabolic activity was quantified using crystal violet (CV) staining and MTT assay, respectively. Biofilm community composition and morphology were assessed by denaturing gradient gel electrophoresis (DGGE), 16S rRNA sequencing and scanning electron microscopy. The ISO6876:2012 specifications were followed to determine the setting time, radiopacity, flowability and solubility. Obturated acrylic teeth were used to assess the sealers' effect on pH. Surface chemical characterization was performed using SEM with coupled energy-dispersive spectroscopy. Data normality was assessed using the Shapiro-Wilk test. One-way anova and Tukey's tests were used to analyze data from setting time, radiopacity, flowability and solubility. Two-way anova and Dunnett's tests were used for the data analysis from CV, MTT and pH. 16S rRNA sequencing data were analyzed for alpha (Shannon index and Chao analysis) and beta diversity (Bray-Curtis dissimilarities). Differences in community composition were evaluated by analysis of similarity (p < .05).

RESULTS

The sealers significantly influenced microbial community composition and morphology. All sealers complied with ISO6876:2012 requirements for setting time, radiopacity and flowability. Although only AHP effectively reduced the biofilm biomass, all sealers, except BRR, reduced biofilm metabolic activity.

CONCLUSION

Despite adequate physical properties, none of the sealers tested prevented biofilm growth. Significant changes in community composition were observed. If observed in vivo, these changes could affect intracanal microbial survival, pathogenicity and treatment outcomes.

Autopolymerizing acrylic repair resin containing low concentration of dimethylaminohexadecyl methacrylate to combat saliva-derived bacteria

Biofilm accumulation on the polymethyl methacrylate (PMMA) restorations negatively affect the prognosis of the provisional restorations or the following treatment. This study developed a novel antibacterial PMMA resin containing low concentration of dimethylaminohexadecyl methacrylate (DMAHDM). Four resins were tested: (1) PMMA resin (Control), (2) 1.25% DMAHDM, (3) 2.5% DMAHDM, (4) 5% DMAHDM. Adding 1.25% DMAHDM into the PMMA resin did not influence the mechanical properties, degree of conversion, monomer releasing, and color stability of the specimens (p > 0.05). The incorporation of DMAHDM into PMMA resin could greatly prevent saliva-derived biofilms adhesion compared with the control group (p < 0.05). The metabolism level of saliva-derived biofilms on the 1.25%, 2.5%, and 5% DMAHDM resins were reduced by 20%, 54%, and 62%, respectively. And the mechanism of DMAHDM disturbing the integrity of bacterial cell walls was confirmed by flow cytometric analysis. Adding 1.25% and 2.5% DMAHDM did not compromise cytocompatibility of the modified resin (p > 0.05). Therefore, novel PMMA resin containing low concentration DMAHDM is promising as a future antimicrobial provisional restoration material for preventing microbial-induced complications in clinical settings. Graphical abstract.

In Vitro Biofilm Formation on Aryl Ketone Polymer (AKP), A New Denture Material, Compared with That on Three Traditional Dental Denture Materials

Control of denture plaque biofilms is a practical approach to preventing persistent oral infections such as denture stomatitis. Objectives. This study compared in vitro biofilm attachment and growth on a new denture material, Ultaire® AKP, with that on traditional denture materials including cobalt chrome (CoCr), polymethyl methacrylate (PMMA), and polyoxymethylene (POM). Methods. Microbial biofilms were grown with cultures of Candida albicans, Streptococcus mutans UA159, or a mixed Streptococcus spp. (S. mutans 700610/Streptococcus sanguinis BAA-1455) for 6 hours in a static protocol or 24 hours in a dynamic protocol for each material. Adherent biofilm cells were removed, and viable colony-forming units (CFUs) were enumerated. Confocal microscopy of the 24-hour Streptococcus spp. biofilms was used to determine biofilm mass and roughness coefficients. Results. The rank order of C. albicans attachment after 6 hours was CoCr > PMMA ^∗  > Ultaire® AKP ^∗ ( ^∗ vs CoCr, p ≤ 0.05), and that for 24-hour biofilm growth was CoCr > Ultaire® AKP ^∗  > PMMA ^∗ ( ^∗ vs CoCr, p ≤ 0.05). The rank order of S. mutans biofilm attachment was CoCr > POM > Ultaire® AKP ^∗  > PMMA ^∗ ( ^∗ vs CoCr, p ≤ 0.05), and that for the 24-hour Streptococcus spp. biofilm growth was POM > Ultaire® AKP > PMMA > CoCr ^∗ ( ^∗ vs POM, p ≤ 0.05). Confocal images revealed structural differences in Streptococcus spp. biofilms on CoCr compared with the other test materials. Significantly lower roughness coefficients of Streptococcus spp. biofilms on Ultaire® AKP were noted, suggesting that these biofilms were less differentiated. Ultaire® AKP promoted significantly less C. albicans and S. mutans biofilm attachment than CoCr at 6 hours and C. albicans growth at 24 hours. Streptococcus spp. biofilms on Ultaire® AKP were less differentiated than those on other test materials. Conclusion. In addition to its material strength, Ultaire® AKP represents an attractive option for denture material in removable partial dentures.

Commercially Available Ion-Releasing Dental Materials and Cavitated Carious Lesions: Clinical Treatment Options

The contemporary approach for operative caries management emphasizes personalized interventions for each patient, dependent upon the individual's caries susceptibility/risk, the stage of the carious lesion and its activity. The clinician's challenge is to optimize the extent of cavity preparation and the choice of dental restorative biomaterials, appreciating the benefits offered by ion-releasing restorative materials. There is a growing application of bioactive/bio-interactive materials in minimally invasive operative dentistry, as they may help with tissue recovery by ion release. In case of moderate or extensive occlusal cavitation, the clinical criteria include the individual caries susceptibility and carious lesion activity. In high caries risk cases, ion-releasing biomaterials (IRB) can be used, as well as for active carious lesions. In proximal lesions, the clinical criteria include the individual caries susceptibility, the lesion activity and presence of cavities with little or no enamel at the gingival margin. This article aims to discuss the restorative ion-releasing options, according to different clinical situations, and the caries susceptibility to manage cavitated carious lesions in permanent adult teeth.

Influence of artificial aging: mechanical and physicochemical properties of dental composites under static and dynamic compression

OBJECTIVE

The aim of the study was to evaluate the influence of filler content, degradation media and time on the mechanical properties of different dental composites after in vitro aging.

MATERIALS AND METHODS

Specimens (1 mm³) of three commercially available composites (GrandioSO®, Arabesk Top®, Arabesk Flow®) with respect to their filler content were stored in artificial aging media: artificial saliva, ethanol (60%), lactic acid (pH 5) and citric acid (pH 5). Parameters (Vickers microhardness, compressive strength, elastic modulus, water sorption and solubility) were determined in their initial state (control group, n = 3 for microhardness, n = 5 for the other parameters) and after 14, 30, 90 and 180 days (n = 3 for microhardness, n = 5 for the other parameters for each composite group, time point and media). Specimens were also characterized with dynamic-mechanical-thermal analysis (compression tests, F =  ± 7 N; f = 0.5 Hz, 1 Hz and 3.3 Hz; t = 0-170 °C).

RESULTS

Incorporation of fillers with more than 80 w% leads to significantly better mechanical properties under static and dynamic compression tests and a better water sorption behavior, even after chemical degradation. The influence of degradation media and time is of subordinate importance for chemical degradation.

CONCLUSION

Although the investigated composites have a similar matrix, they showed different degradation behavior. Since dentine and enamel occur only in small layer thickness, a test specimen geometry with very small dimensions is recommended for direct comparison. Moreover, the use of compression tests to determine the mechanical parameters for the development of structure-compatible and functionally adapted composites makes sense as an additional standard. Clinical relevance Preferential use of highly filled composites for occlusal fillings is recommended.

An ultrasonic-based experimental model to evaluate the setting time of endodontic sealers

AIM

To evaluate an ultrasonic-based experimental model (US), to assess the setting time of AH Plus^® , Bio-C Sealer^® and MTA Fillapex^® , and compare the results obtained with ANSI/ADA specifications (2012).

METHODS

To determine the setting time according to the ANSI/ADA specification, moulds measuring 10 mm (diameter) × 2 mm (thickness) were used, and for the US tests a transducer (1 MHz) and an oscilloscope were used. Fourier-transform infrared spectroscopy (FTIR) was used to evaluate the changes on chemical structure at the different setting times found by the US and ANSI/ADA methods. After checking the normal distribution, setting time data were analysed using unilateral analysis of variance with Tukey-HSD post-test to compare the methods.

RESULTS

AH Plus^® and Bio-C Sealer^® had longer mean setting time values for the US method than for the ANSI/ADA (p < .05), whilst for MTA Fillapex^® no significant difference was found between the methods (p < .05). FTIR spectra demonstrated that at the setting time determined by the US method, AH Plus^® and Bio-C Sealer^® were in a more advanced stage of polymerization than at the ANSI/ADA, whilst there was no significant difference for MTA Fillapex^® .

CONCLUSIONS

The use of US was effective for setting time determination and measured longer values than ANSI/ADA specification for AH Plus^® and Bio-C Sealer^® , identifying the entire (and not only superficial) setting of the endodontic sealers.

Characteristics of biofilm-induced degradation at resin-dentin interfaces using multiple combinations of adhesives and resins

OBJECTIVE

We aimed to evaluate morphological, mechanical and chemical characteristics at resin-dentin interfaces using multiple combinations of adhesives and resins after a short-term biofilm-induced degradation.

METHODS

Cervical cavities were prepared in bovine incisors, treated by Clearfil SE Bond 2 (SE) or FL-Bond II (FL), restored by Clearfil Majesty ES Flow (ES) or Beautifil Flow Plus (BFP) and grouped into SE-ES, SE-BFP, FL-ES and FL-BFP. After biofilm challenge, interfacial gaps and dentin wall lesions were examined by optical coherence tomography (OCT). Gap depth (GD), gap pattern scale (GPS) and dentin wall lesion depth (WLD) were evaluated from confocal laser scanning microscope. Microhardness of dentin lesions was measured with a Vickers microhardness tester. Chemical elements in resins and dentin wall lesions were analyzed by scanning electron microscopy and energy dispersive X-ray spectrometry (SEM/EDS). Morphological structures of interfacial gaps were observed by SEM.

RESULTS

OCT could detect adhesive-dentin-bonded and adhesive-dentin-debonded gaps. SE-containing groups showed significantly lower GPS than FL-containing groups. FL-BFP showed significantly lower WLD than FL-ES. Microhardness of dentin wall lesions was higher than that of outer lesions and they showed significant differences in FL-BFP. SE-BFP showed a lower GPS curve and higher intensities of Ca and P in the upper half of dentin wall lesions than other groups. From SEM, microgaps between filler and matrix, break and loss of matrix, separation of adhesive matrix with hybrid layer occurred at interfacial gaps.

SIGNIFICANCE

The morphological, mechanical and chemical characteristics of resin-dentin interfacial degradation depend on the component and chemistry of restorative materials.

Digital image correlation in dental materials and related research: A review

OBJECTIVE

Digital image correlation (DIC) is a non-contact image processing technique for full-field strain measurement. Although DIC has been widely used in engineering and biomechanical fields, it is in the spotlight only recently in dental materials. Therefore, the purpose of this review paper is introducing the working principle of the DIC technique with some modifications and providing further potential applications in various dental materials and related fields.

METHODS

The accuracy of the algorithm depending on the environmental characteristics of the DIC technique, as well as the advantages and disadvantages of strain measurement using optical measurements, have been elaborated in dental materials and related fields. Applications to those researches have been classified into the following categories: shrinkage behavior of light-cured resin composite, resin-tooth interface, mechanical properties of tooth structure, crack extension and elastic properties of dental materials, and deformation of dental restoration and prosthesis. This classification and discussion were performed using literature survey and review based on numerous papers in the international journals published over the past 20 years. The future directions for predicting the precise deformation of dental materials under various environments, as well as limitations of the DIC technique, was presented in this review.

RESULTS

The DIC technique was demonstrated as a more effective tool to measure full-field polymerization shrinkage of composite resin, even in a simulated clinical condition over the existing methods. Moreover, the DIC combined with other technologies can be useful to evaluate the mechanical behavior of material-tooth interface, dentine structure and restorative and prosthetic materials with high accuracy. Three-dimensional DIC using two cameras extended the measurement range in-plane to out-of-plane, enabling measure of the strain directly on the surface of dental restorations or prosthesis.

SIGNIFICANCE

DIC technique is a potential tool for measuring and predicting the full-field deformation/strain of dental materials and actual prostheses in diverse clinical conditions. The versatility of DIC can replace the existing complex sensor devices in those studies.

Influence of Additive Firing on the Surface Characteristics, Streptococcus mutans Viability and Optical Properties of Zirconia

The purpose of this study was to observe whether the repetitive firing of dental zirconia caused changes in surface characteristics, S. mutans viability, and optical properties of zirconia. Dental zirconia blocks were sintered and randomly distributed into seven experimental groups: F0–F6. Except for F0, which only went through sintering, the additive firing was performed in order for F1–F6. Surface roughness, contact angle, S. mutans viability by fluorescence, and translucency parameter were measured. They were all highest after sintering (F0) and decreased after additive firings (F1–F6). The additive firing of zirconia after sintering decreased surface roughness, contact angle, S. mutans viability, and translucency. The number of firings after the first firing was not found to be critical in surface characteristics, S. mutans viability, and optical property. Changes in surface characteristics might have led to a decrease in S. mutans viability, while the change of translucency was not clinically significant. This implies that additive firing may prevent secondary caries under zirconia restorations, not compromising esthetic appearance.

pH-dependent delivery of chlorhexidine from PGA grafted mesoporous silica nanoparticles at resin-dentin interface

Background

A low pH environment is created due to the production of acids by oral biofilms that further leads to the dissolution of hydroxyapatite crystal in the tooth structure significantly altering the equilibrium. Although the overall bacterial counts may not be eradicated from the oral cavity, however, synthesis of engineered anti-bacterial materials are warranted to reduce the pathogenic impact of the oral biofilms. The purpose of this study was to synthesize and characterize chlorhexidine (CHX)-loaded mesoporous silica nanoparticles (MSN) grafted with poly-L-glycolic acid (PGA) and to test the in vitro drug release in various pH environments, cytotoxicity, and antimicrobial capacity. In addition, this study aimed to investigate the delivery of CHX-loaded/MSN-PGA nanoparticles through demineralized dentin tubules and how these nanoparticles interact with tooth dentin after mixing with commercial dentin adhesive for potential clinical application.

Results

Characterization using SEM/TEM and EDX confirmed the synthesis of CHX-loaded/MSN-PGA. An increase in the percentage of drug encapsulation efficiency from 81 to 85% in CHX loaded/MSN and 92–95% in CHX loaded/MSN-PGA proportionately increased with increasing the amount of CHX during the fabrication of nanoparticles. For both time-periods (24 h or 30 days), the relative microbial viability significantly decreased by increasing the CHX content (P < 0.001). Generally, the cell viability percentage of DPSCs exposed to MSN-PGA/Blank, CHX-loaded/MSN, and CHX-loaded/MSN-PGA, respectively was > 80% indicating low cytotoxicity profiles of experimental nanoparticles. After 9 months in artificial saliva (pH 7.4), the significantly highest micro-tensile bond strength value was recorded for 25:50 CHX/MSN and 25:50:50 CHX/MSN-PGA. A homogenous and widely distributed 50:50:50 CHX-loaded/MSN-PGA nanoparticles exhibited excellent bonding with the application of commercially available dentin adhesive.

Conclusions

A pH-sensitive CHX release response was noted when loaded in MSN grafted PGA nanoparticles. The formulated drug-loaded nanocarrier demonstrated excellent physicochemical, spectral, and biological characteristics. Showing considerable capacity to penetrate effectively inside dentinal tubules and having high antibacterial efficacy, this system could be potentially used in adhesive and restorative dentistry.

Biodegradation of orthodontic composites by Streptococcus mutans: An in vitro qualitative and quantitative assessment

Objectives:

The purpose of this study was to evaluate the degradation products of orthodontic composites (Grengloo, Blugloo, Transbond XT, and Transbond LR) by Streptococcus mutans and then to quantify the levels of released bisphenol A (BPA) using gas-phase chromatography and mass spectrometry (GC–MS).

Materials and Methods:

Orthodontic light-cured composite discs were incubated at 37°C in brain heart infusion (BHI) (control group) and in a culture of S. mutans with BHI (test group). Incubation solutions were collected every 48 h in each group and replaced with fresh solutions. These incubation solutions were accumulated and grouped. The assessment of degradation products from composites was done at 1 and 30 days. Detected BPA was then quantified. The limit of quantification was 0.01 μg/mL.

Results:

Degradation products were present at day 30. For the test group, BPA was detected in Blugloo at day 1 (0.38 μg/mL) and triethylene glycol dimethacrylate (TEGDMA) was detected in Grengloo and Transbond LR at day 1.

Conclusion:

S. mutans can hydrolyze long-term orthodontic composites. Monomers such as BPA and TEGDMA may be present in degradation products. It is possible to separate and identify leaching compounds by GC–MS technique.

Novel Nanocomposite Inhibiting Caries at the Enamel Restoration Margins in an In Vitro Saliva-Derived Biofilm Secondary Caries Model

Secondary caries often occurs at the tooth-composite margins. This study developed a novel bioactive composite containing DMAHDM (dimethylaminohexadecyl methacrylate) and NACP (nanoparticles of amorphous calcium phosphate), inhibiting caries at the enamel restoration margins in an in vitro saliva-derived biofilm secondary caries model for the first time. Four composites were tested: (1) Heliomolar nanocomposite, (2) 0% DMAHDM + 0% NACP, (3) 3% DMAHDM + 0% NACP, (D) 3% DMAHDM + 30% NACP. Saliva-derived biofilms were tested for antibacterial effects of the composites. Bovine enamel restorations were cultured with biofilms, Ca and P ion release of nanocomposite and enamel hardness at the enamel restoration margins was measured. Incorporation of DMAHDM and NACP into composite did not affect the mechanical properties (p > 0.05). The biofilms’ CFU (colony-forming units) were reduced by 2 logs via DMAHDM (p < 0.05). Ca and P ion release of the nanocomposite was increased at cariogenic low pH. Enamel hardness at the margins for DMAHDM group was 25% higher than control (p < 0.05). With DMAHDM + NACP, the enamel hardness was the greatest and about 50% higher than control (p < 0.05). Therefore, the novel composite containing DMAHDM and NACP was strongly antibacterial and inhibited enamel demineralization, resulting in enamel hardness at the margins under biofilms that approached the hardness of healthy enamel.

Interaction between the Oral Microbiome and Dental Composite Biomaterials: Where We Are and Where We Should Go

Dental composites are routinely placed as part of tooth restoration procedures. The integrity of the restoration is constantly challenged by the metabolic activities of the oral microbiome. This activity directly contributes to a less-than-desirable half-life for the dental composite formulations currently in use. Therefore, many new antimicrobial dental composites are being developed to counteract the microbial challenge. To ensure that these materials will resist microbiome-derived degradation, the model systems used for testing antimicrobial activities should be relevant to the in vivo environment. Here, we summarize the key steps in oral microbial colonization that should be considered in clinically relevant model systems. Oral microbial colonization is a clearly defined developmental process that starts with the formation of the acquired salivary pellicle on the tooth surface, a conditioned film that provides the critical attachment sites for the initial colonizers. Further development includes the integration of additional species and the formation of a diverse, polymicrobial mature biofilm. Biofilm development is discussed in the context of dental composites, and recent research is highlighted regarding the effect of antimicrobial composites on the composition of the oral microbiome. Future challenges are addressed, including the potential of antimicrobial resistance development and how this could be counteracted by detailed studies of microbiome composition and gene expression on dental composites. Ultimately, progress in this area will require interdisciplinary approaches to effectively mitigate the inevitable challenges that arise as new experimental bioactive composites are evaluated for potential clinical efficacy. Success in this area could have the added benefit of inspiring other fields in medically relevant materials research, since microbial colonization of medical implants and devices is a ubiquitous problem in the field.

Polymeric nanoparticles protect the resin-dentin bonded interface from cariogenic biofilm degradation

The objective was to assess doxycycline (Dox) and zinc (Zn) doped nanoparticles' (NPs) potential to protect the resin-dentin interface from cariogenic biofilm. Three groups of polymeric NPs were tested: unloaded, loaded with zinc and with doxycycline. NPs were applied after dentin etching. The disks were exposed to a cariogenic biofilm challenge in a Drip-Flow Reactor during 72 h and 7 d. Half of the specimens were not subjected to biofilm formation but stored 72 h and 7 d. LIVE/DEAD® viability assay, nano-dynamic mechanical assessment, Raman spectroscopy and field emission electron microscopy (FESEM) analysis were performed. The measured bacterial death rates, at 7 d were 46% for the control group, 51% for the undoped-NPs, 32% for Dox-NPs, and 87% for Zn-NPs; being total detected bacteria reduced five times in the Dox-NPs group. Zn-NPs treated samples reached, in general, the highest complex modulus values at the resin-dentin interface over time. Regarding the mineral content, Zn-NPs-treated dentin interfaces showed the highest mineralization degree associated to the phosphate peak and the relative mineral concentration. FESEM images after Zn-NPs application permitted to observe remineralization of the etched and non-resin infiltrated collagen layer, and bacteria were scarcely encountered. The combined antibacterial and remineralizing effects, when Zn-NPs were applied, reduced biofilm formation. Dox-NPs exerted an antibacterial role but did not remineralize the bonded interface. Undoped-NPs did not improve the properties of the interfaces. Application of Zn-doped NPs during the bonding procedure is encouraged. STATEMENT OF SIGNIFICANCE: Application of Zn-doped nanoparticles on acid etched dentin reduced biofilm formation and viability at the resin-dentin interface due to both remineralization and antibacterial properties. Doxycycline-doped nanoparticles also diminished oral biofilm viability, but did not remineralize the resin-dentin interface.

Effect of arginine on microorganisms involved in dental caries: a systematic literature review of in vitro studies

This systematic review aimed to discuss the effects of arginine on caries-related microorganisms in different in vitro biofilm models. The eligibility criteria were in vitro studies that evaluated the effect of arginine at different concentrations on caries-related microorganisms using biofilm models. Eighteen studies published between 2012 and 2019 were included. Different bacterial species were studied. Seventeen studies (94.4%) achieved a low risk of bias and only one showed a medium risk of bias. The studies showed that arginine is a promising approach for the ecological management of dental caries. The focus of this review was to evaluate the effects of arginine on microorganisms involved in the mechanism of dental caries.

Dental adhesive microtensile bond strength following a biofilm-based in vitro aging model

OBJECTIVE

Laboratory tests are routinely used to test bonding properties of dental adhesives. Various aging methods that simulate the oral environment are used to complement these tests for assessment of adhesive bond durability. However, most of these methods challenge hydrolytic and mechanical stability of the adhesive- enamel/dentin interface, and not the biostability of dental adhesives. To compare resin-dentin microtensile bond strength (μTBS) after a 15-day Streptococcus mutans (SM) or Streptococcus sobrinus (SS) bacterial exposure to the 6-month water storage (WS) ISO 11405 type 3 test.

METHODOLOGY

A total of 31 molars were flattened and their exposed dentin was restored with Optibond-FL adhesive system and Z-100 dental composite. Each restored molar was sectioned and trimmed into four dumbbell-shaped specimens, and randomly distributed based on the following aging conditions: A) 6 months of WS (n=31), B) 5.5 months of WS + 15 days of a SM-biofilm challenge (n=31), C) 15 days of a SM-biofilm challenge (n=31) and D) 15 days of a SS-biofilm challenge (n=31). μTBS were determined and the failure modes were classified using light microscopy.

RESULTS

Statistical analyses showed that each type of aging condition affected μTBS (p<0.0001). For Group A (49.7±15.5MPa), the mean μTBS was significantly greater than in Groups B (19.3±6.3MPa), C (19.9±5.9MPa) and D (23.6±7.9MPa). For Group D, the mean μTBS was also significantly greater than for Groups B and C, but no difference was observed between Groups B and C.

CONCLUSION

A Streptococcus mutans- or Streptococcus sobrinus-based biofilm challenge for 15 days resulted in a significantly lower μTBS than did the ISO 11405 recommended 6 months of water storage. This type of biofilm-based aging model seems to be a practical method for testing biostability of resin-dentin bonding.

Effect of Etching Procedures on the Adhesion of Biofilm-Coated Dentin

Oral biofilms coat all surfaces in the oral cavity including the exposed dentin surface. This study aimed to investigate biofilm removal by acid etching procedures and the effects of the residual biofilm on dentin surfaces on composite-dentin adhesion. Dentin discs were assigned to five groups: no biofilm formation (C); biofilm formation and no surface treatment (BF); biofilm formation and acid etching (BF-E); biofilm formation and acid etching followed by chlorhexidine soaking (BF-EC); and biofilm formation and rubbing with pumice, followed by acid etching (BF-RE). Biofilms were formed on saliva-precoated dentin discs by soaking the discs in Streptococcus mutans (S. mutans) suspension. Biofilm removal from the dentin surface was evaluated quantitatively and qualitatively by confocal laser scanning microscopy and scanning electron microscopy, respectively. To compare the bond strength of the biofilm-coated dentin discs with the surface treatments, specimens were assigned to four groups: no biofilm formation and acid etching (C-E); BF-E; BF-EC; and BF-RE. Assessments of the micro-shear bond strength and subsequent failure modes were performed. BF-E and BF-EC did not remove the biofilm, whereas BF-RE partially removed the biofilm attached to the dentin (p < 0.05). The bond strength of BF-RE was significantly higher than those of BF-E and BF-EC, but lower than that of C-E (p < 0.05). In conclusion, mechanical biofilm removal is recommended before etching procedures to enhance adhesion to the biofilm-coated dentin.

Development and calibration of biochemical models for testing dental restorations

Currently, resin composites are the most popular materials for dental restoration in clinical practice. Although the properties of such materials have been improved significantly, together with better clinical techniques used for their placement, early restoration failure still occurs too frequently. As clinical studies take years to complete, and new resin composites are being produced at ever increasing pace, laboratory assessment using accelerated but representative tests is necessary. The main types of failure in resin-composite restoration are tooth/restoration fracture and secondary caries, which are caused by a combination of mechanical and biochemical challenges. In this study, a biofilm model (S. mutans) and a chemical model (lactic-acid buffer) for producing artificial caries in bovine dentin are developed and calibrated against in situ data. Using a power law relationship between the demineralization depth and challenge duration, scale factors that convert the in vitro durations to the equivalent clinical durations are determined for different pH values for each model. The scale factors will allow the synchronization of biochemical and mechanical challenges in terms of their rates of action to potentially test resin-composite restoration in an accelerated but clinically representative manner. STATEMENT OF SIGNIFICANCE: Although the properties of resin composites for dental restoration have been improved significantly, early restoration failure still occurs too frequently. As clinical studies take years to complete, accelerated laboratory testing is necessary. Resin-composite restoration fail mainly through fracture and secondary caries, caused by a combination of mechanical and biochemical challenges. In this study, a biofilm and a chemical model for producing artificial caries in bovine dentin are calibrated against in situ data. Using a power law relationship between demineralization depth and challenge duration, scale factors are determined for different pH for each model. The scale factors will allow the synchronization of biochemical and mechanical challenges in testing resin-composite restoration in an accelerated but clinically representative manner.

Effect of Polyols and Selected Dental Materials on the Ability to Create a Cariogenic Biofilm-On Children Caries-Associated Streptococcus Mutans Isolates

Secondary caries is a disease associated with the formation of biofilm on the border of the tooth and dental filling. Its development is strongly influenced by the dietary sweet foods and the type of dental material. The aim of the study was to assess the effect of sweeteners on the ability of clinical Streptococcus mutans strains to form biofilm on dental materials. Strains were isolated from plaque samples from 40 pediatric patients from the 3-6 ICADS II group. The ability to form biofilm was tested on composite and glass ionomer dental materials used for milk teeth filling in the presence of sucrose, xylitol, sorbitol, and erythritol. The bacterial film mass after 12, 24, 48, and 72 h and the number of bacterial colonies significantly decreased (p < 0.01) compared to the initial value for 5% erythritol and sorbitol on examined materials. A greater inhibitory effect was noted for glass ionomers compared to composites. Sucrose and xylitol supported biofilm formation, while erythritol had the best inhibitory effect. The use of fluoride-releasing glass ionomers exerted an effect synergistic to erythritol, i.e., inhibited plaque formation and the amount of cariogenic S. mutans. Selection of proper type of dental material together with replacing sucrose with polyols can significantly decrease risk of secondary caries development. Erithritol in combination with glass ionomer seems to be the most effective in secondary caries prevention.

Fabrication of Robust Antibacterial Coatings Based on an Organic-Inorganic Hybrid System

Antibacterial coatings have drawn much attention because of their high potential applications in medicine. However, the weak mechanical property, poor biosafety, and biocompatibility of most established antibacterial coatings restrict their applications. In this study, robust antibacterial coatings were fabricated via a simple organic-inorganic hybrid method. The polymer component provides an excellent antibacterial property to the coatings, and the hybrid silica sol improves the hardness of coatings. After cross-linking, network-structured coatings were formed. The coating surfaces exhibited high transmittance, excellent mechanical property, and good antibacterial effect against Escherichia coli (Gram-negative) and Streptococcus mutans (Gram-positive). Additionally, the robust coatings were noncytotoxic with satisfactory biocompatibility. Such results provide a theoretical basis for their applications in the biomedical field.

Threats to adhesive/dentin interfacial integrity and next generation bio-enabled multifunctional adhesives

Nearly 100 million of the 170 million composite and amalgam restorations placed annually in the United States are replacements for failed restorations. The primary reason both composite and amalgam restorations fail is recurrent decay, for which composite restorations experience a 2.0-3.5-fold increase compared to amalgam. Recurrent decay is a pernicious problem-the standard treatment is replacement of defective composites with larger restorations that will also fail, initiating a cycle of ever-larger restorations that can lead to root canals, and eventually, to tooth loss. Unlike amalgam, composite lacks the inherent capability to seal discrepancies at the restorative material/tooth interface. The low-viscosity adhesive that bonds the composite to the tooth is intended to seal the interface, but the adhesive degrades, which can breach the composite/tooth margin. Bacteria and bacterial by-products such as acids and enzymes infiltrate the marginal gaps and the composite's inability to increase the interfacial pH facilitates cariogenic and aciduric bacterial outgrowth. Together, these characteristics encourage recurrent decay, pulpal damage, and composite failure. This review article examines key biological and physicochemical interactions involved in the failure of composite restorations and discusses innovative strategies to mitigate the negative effects of pathogens at the adhesive/dentin interface. © 2019 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 107B:2466-2475, 2019.

Testing Anti-Biofilm Polymeric Surfaces: Where to Start?

Present day awareness of biofilm colonization on polymeric surfaces has prompted the scientific community to develop an ever-increasing number of new materials with anti-biofilm features. However, compared to the large amount of work put into discovering potent biofilm inhibitors, only a small number of papers deal with their validation, a critical step in the translation of research into practical applications. This is due to the lack of standardized testing methods and/or of well-controlled in vivo studies that show biofilm prevention on polymeric surfaces; furthermore, there has been little correlation with the reduced incidence of material deterioration. Here an overview of the most common methods for studying biofilms and for testing the anti-biofilm properties of new surfaces is provided.

The causes of failure and the longevity of direct coronal restorations: A survey among dental surgeons of the town of Abidjan, Côte d'Ivoire

Objective:

This study aimed to itemize the causes for the failure of direct coronal restorations (DCRs) according to the practitioners of Côte d'Ivoire in order to provide recommendations for good practice.

Materials and Methods:

A descriptive, self-reporting, prospective survey was carried out among 109 dental surgeons (DSs) in the town of Abidjan based on 587 randomly selected practitioners supplied by the National Board of the Order.

Results:

The results show that 98.10% of the surveyed DSs had previously encountered cases of failure. Fracturing of the restoration, which is the basis for the hiatus, is the main cause of failure according to 51.40% of the surveyed practitioners, followed by pain “under the restoration” cited by 26.20% of them. Failure occurs within 6 months (30.85% of those surveyed), after 5 years (9.6% of those surveyed) for restorations with composite or glass ionomer cement (GIC), while for DCRs with amalgam, failure occurs within 6 months (28.70%), after 5 years (16%) and beyond 10 years (3.20%).

Conclusion:

The practitioners often encountered failures of DCRs, with fracture of the restoration as the cause. Dental amalgam appears to have a greater longevity than adhesive restorations. Faced with a failure, they more often opted for a replacement of the DCRs rather than a repair.

Experimental composites containing quaternary ammonium methacrylates reduce demineralization at enamel-restoration margins after cariogenic challenge

OBJECTIVE

This study evaluated the influence of experimental composites containing quaternary ammonium monomers (QAM) at different concentrations and alkyl chains on demineralization at enamel-composite margins after cariogenic challenge.

METHODS

Standardized 4×4mm cavities were cut into 35 bovine enamel blocks, which were randomly divided into seven groups (n=5) and restored with the following experimental composites and commercial materials: (G12.5) - 5% dimethylaminododecyl methacrylate (DMADDM) with a 12-carbon alkyl chain (G12.10) - 10% DMADDM, (G16.5) - 5% dimethylaminohexadecyl methacrylate (DMAHDM) with a 16-carbon alkyl chain (G16.10) - 10% DMAHDM, (CG) - control group (without QAM), (GZ250) - commercial composite (Filtek Z250^®), and (GIC) - glass ionomer cement (Maxxion R^®). After restorative procedures, initial microhardness was measured and experimental composites were subjected to Streptococcus mutans biofilm formation for 48h. After cariogenic challenge, the samples were washed and microhardness was reassessed. A 3D non-contact profilometer was used to determine surface roughness and enamel demineralization was assessed by micro-CT. Microhardness results were analyzed by the Kruskal-Wallis and Mann-Whitney tests and micro-CT results were analyzed by Tukey's HSD test (95% confidence interval).

RESULTS

None of the materials could prevent mineral loss at the enamel-restoration margins. The addition of 10% DMAHDM yielded the lowest, albeit statistically significant, mineral loss (p<0.05). 3D non-contact profilometry showed enamel surface roughness modification after biofilm exposure. The CG had the highest roughness values. Micro-CT analysis revealed mineral loss, except for GIC.

SIGNIFICANCE

The addition of 10% QAM with a 16-carbon chain in experimental composites reduced mineral loss at the enamel-restoration margins after cariogenic challenge.

Bioreactors Design, Types, Influencing Factors and Potential Application in Dentistry. A Literature Review

Objectives:

A variety of bioreactors and related approaches have been applied to dental tissues as their use has become more essential in the field of regenerative dentistry and dental tissue engineering. The review discusses the various types of bioreactors and their potential application in dentistry.

Methods:

Review of the literature was conducted using keywords (and MeSH) like Bioreactor, Regenerative Dentistry, Fourth Factor, Stem Cells, etc., from the journals published in English. All the searched abstracts, published in indexed journals were read and reviewed to further refine the list of included articles. Based on the relevance of abstracts pertaining to the manuscript, full-text articles were assessed.

Results:

Bioreactors provide a prerequisite platform to create, test, and validate the biomaterials and techniques proposed for dental tissue regeneration. Flow perfusion, rotational, spinner-flask, strain and customize-combined bioreactors have been applied for the regeneration of bone, periodontal ligament, gingiva, cementum, oral mucosa, temporomandibular joint and vascular tissues. Customized bioreactors can support cellular/biofilm growth as well as apply cyclic loading. Center of disease control & dip-flow biofilm-reactors and micro-bioreactor have been used to evaluate the biological properties of dental biomaterials, their performance assessment and interaction with biofilms. Few case reports have also applied the concept of in vivo bioreactor for the repair of musculoskeletal defects and used customdesigned bioreactor (Aastrom) to repair the defects of cleft-palate.

Conclusions:

Bioreactors provide a sterile simulated environment to support cellular differentiation for oro-dental regenerative applications. Also, bioreactors like, customized bioreactors for cyclic loading, biofilm reactors (CDC & drip-flow), and micro-bioreactor, can assess biological responses of dental biomaterials by simultaneously supporting cellular or biofilm growth and application of cyclic stresses.

In vitro evaluation of the antibacterial behavior of a self-etch adhesive associated with chlorhexidine

Abstract Introduction Adhesive technology has been developed quickly since its introduction about fifty years ago. Its goal is to produce a close contact within enamel and dentin. Failures in this process could result in microleakage, and allow the infiltration of bacteria, fluids and ions. Recent studies have been shown the use of chlorhexidine associated with adhesive systems can be able to inhibit the bacteria action. Objective The aim of this study was to evaluate the addiction of different percentages of chlorhexidine to a self-etch adhesive. Methodology The solution of digluconatechlorhexidine was increased to the primer of the two pass self etch adhesive to create a 0.5%, 1.0% and 2.0% chlorhexidine primer solution and after they were distributed in four groups (G1, G2, G3 and G4). Saliva samples (N=10) were used to test bacteria activity. Result They were spread in a blood medium with filter paper disks containing the different treatments. After the incubation, the inhibitions halos formation were evaluated. Conclusion This study demonstrated that, in vitro, the addition of different percentages of chlorhexidine digluconate to the self-etch adhesive induced inhibited halos at bacteria of saliva samples, independent from their concentration.

New silyl-functionalized BisGMA provides autonomous strengthening without leaching for dental adhesives

Resin-based composite has overtaken dental amalgam as the most popular material for direct restorative dentistry. In spite of this popularity the clinical lifetime of composite restorations is threatened by recurrent decay. Degradation of the adhesive leads to gaps at the composite/tooth interface-bacteria, bacterial by-products and fluids infiltrate the gaps leading to recurrent decay and composite restoration failure. The durability of resin-dentin bonds is a major problem. We address this problem by synthesizing silyl-functionalized BisGMA (e.g., silyl-BisGMA), formulating dental adhesives with the new monomer and determining the physicochemical properties and leaching characteristics of the silyl-BisGMA adhesives. Silyl-BisGMA was synthesized by stoichiometric amounts of BisGMA and 3-isocyanatopropyl trimethoxysilane (IPTMS). The control adhesive was a mixture based on HEMA/BisGMA (45/55, w/w). In the experimental formulations, BisGMA was partially or completely replaced by silyl-BisGMA. Water miscibility, polymerization behavior (Fourier transform infrared spectroscopy, FTIR), thermal property (modulated differential scanning calorimetry, MDSC), mechanical properties in dry and wet conditions (dynamic mechanical analysis, DMA), and leached species (HPLC) were investigated. Data from all tests were submitted to appropriate statistical analysis (α = 0.05). Silyl-BisGMA-containing adhesives exhibited comparable water miscibility, lower viscosities, and significantly improved degree of conversion of CC bond as compared to the control. After 4 weeks aqueous aging, the glass transition temperature and rubbery moduli of the experimental copolymers were significantly greater than the control (p < 0.05). HPLC results indicated a substantial reduction of leached HEMA (up to 99 wt%) and BisGMA (up to 90 wt%). By introducing silyl-functional group, the new BisGMA derivative exhibited potential as a monomer that can lead to dental adhesives with improved mechanical properties and reduced leaching under conditions relevant to the oral environment. STATEMENT OF SIGNIFICANCE: The low-viscosity adhesive that bonds the composite to the tooth (enamel and dentin) is intended to seal and stabilize the composite/tooth interface, but it degrades leading to a breach at the composite/tooth margin. As the most popular crosslinking monomer in adhesives, Bisphenol A-glycerolate dimethacrylate (BisGMA) has limitations, e.g. susceptible to hydrolysis and concomitant property degradation. A methoxysilyl-functionalized BisGMA derivative (silyl-BisGMA) was introduced in this work to respond to these limitations. Our results indicated that by introducing silyl-BisGMA, higher crosslinked networks were obtained without sacrificing the homogeneity, and the leached amount of HEMA was reduced up to 99%. This novel resin offers potential benefits including prolonging the functional lifetime of dental resin materials.

Influence of Dental Prosthesis and Restorative Materials Interface on Oral Biofilms

Oral biofilms attach onto both teeth surfaces and dental material surfaces in oral cavities. In the meantime, oral biofilms are not only the pathogenesis of dental caries and periodontitis, but also secondary caries and peri-implantitis, which would lead to the failure of clinical treatments. The material surfaces exposed to oral conditions can influence pellicle coating, initial bacterial adhesion, and biofilm formation, due to their specific physical and chemical characteristics. To define the effect of physical and chemical characteristics of dental prosthesis and restorative material on oral biofilms, we discuss resin-based composites, glass ionomer cements, amalgams, dental alloys, ceramic, and dental implant material surface properties. In conclusion, each particular chemical composition (organic matrix, inorganic filler, fluoride, and various metallic ions) can enhance or inhibit biofilm formation. Irregular topography and rough surfaces provide favorable interface for bacterial colonization, protecting bacteria against shear forces during their initial reversible binding and biofilm formation. Moreover, the surface free energy, hydrophobicity, and surface-coating techniques, also have a significant influence on oral biofilms. However, controversies still exist in the current research for the different methods and models applied. In addition, more in situ studies are needed to clarify the role and mechanism of each surface parameter on oral biofilm development.

Biostable, antidegradative and antimicrobial restorative systems based on host-biomaterials and microbial interactions

OBJECTIVES

Despite decades of development and their status as the restorative material of choice for dentists, resin composite restoratives and adhesives exhibit a number of shortcomings that limit their long-term survival in the oral cavity. Herein we review past and current work to understand these challenges and approaches to improve dental materials and extend restoration service life.

METHODS

Peer-reviewed work from a number of researchers as well as our own are summarized and analyzed. We also include yet-unpublished work of our own. Challenges to dental materials, methods to assess new materials, and recent material improvements and research directions are presented.

RESULTS

Mechanical stress, host- and bacterial-biodegradation, and secondary caries formation all contribute to restoration failure. In particular, several host- and bacterial-derived enzymes degrade the resin and collagen components of the hybrid layer, expanding the marginal gap and increasing access to bacteria and saliva. Furthermore, the virulence of cariogenic bacteria is up-regulated by resin biodegradation by-products, creating a positive feedback loop that increases biodegradation. These factors work synergistically to degrade the restoration margin, leading to secondary caries and restoration failure. Significant progress has been made to produce hydrolytically stable resins to resist biodegradation, as well as antimicrobial materials to reduce bacterial load around the restoration. Ideally, these two approaches should be combined in a holistic approach to restoration preservation.

SIGNIFICANCE

The oral cavity is a complex environment that poses an array of challenges to long-term material success; materials testing conditions should be comprehensive and closely mimic pathogenic oral conditions.