Reactivity of sugar cane bagasse as a natural solid phase extractor for selective removal of Fe(III) and heavy-metal ions from natural water samples

A unique, inexpensive, and abundantly available adsorbent: composite of synthesized silver nanoparticles (AgNPs) and banana leaves powder (BLP)

The purpose of this study is to investigate the development of a new and inexpensive adsorbent by immobilization synthesized silver nanoparticles (AgNPs) onto banana leaves powder (BLP), and the prepared composite (BLP)/(AgNPs) was used as an adsorbent for Zn(II), Pb(II), and Fe(III) ion removal from aqueous solutions under the influence of various reaction conditions. (BLP)/(AgNPs) demonstrated remarkable sensitivity toward Zn (II), Pb (II), and Fe (III) ions; metal ions eliminations increased with increasing contact time, agitation speed, adsorbent dose, and temperature, yielding adequate selectivity and ideal removal efficiency of 79%, 88%, and 91% for Zn (II), Pb (II), and Fe (III) ions, respectively, at pH = 5 for Zn(II) and pH = 6 for Pb(II), and Fe(III). The equilibrium contact time for elimination of Zn (II), Pb (II), and Fe (III) ions was reaches at 40 min. Langmuir, Freundlich, and Temkin equations were used to test the obtained experimental data. Langmuir isotherm model was found to be more accurate in representing the data of Zn(II), Pb(II), and Fe(III) ions adsorption onto (BLP)/(AgNPs), with a regression coefficient (R² = 0.999) and maximum adsorption capacities of 190, 244, and 228 mg/g for Zn(II), Pb(II), and Fe(III) ions, respectively. The thermodynamic parameters proved that adsorption of metal ions is spontaneous, feasible, and endothermic, whereas Kinetic studies revealed that the process was best described by a pseudo second order kinetics.

•

By reduction reaction, silver nanoparticles were impregnated in banana leaves homogeneous powder and used as an adsorbent.

•

The fabricated composites are used as adsorbent for the removal of Zn (II), Pb (II), and Fe (III) ions from aqueous solutions.

•

The new adsorbent exhibited high adsorption capacity with three metal ions and followed the order Pb (II)> Fe (III) >Zn (II) ions.

•

The metal ions vanished from the solution within approximately 40 min.

Removal of Copper (II) from Aqueous Solution by a Hierarchical Porous Hydroxylapatite-Biochar Composite Prepared with Sugarcane Top Internode Biotemplate

Porous hydroxyapatite-biochar composites with layered microstructures (SC–HA/C) were prepared by carbonizing sugarcane stem nodes and then soaking them in lime water and (NH4)2HPO4 solutions in rotation. The surface area of SC–HA/C ranges from 8.52 to 28.44 m2/g, and its microstructure inherits various macro-, meso-, and micro-pores in the cell walls of sugarcane and in the pits of the vessel walls. The maximum removal capacities were 11.50, 14.65, and 19.81 mg/g for the Cu (II) immobilization at 25 °C, 35 °C, and 45 °C with the solution Cu (II) concentration of 10~320 mg/L, respectively, which were in accordance with the copper sorption capacities of synthesized nano-hydroxylapatites. The Cu (II)-removal kinetics and isotherm followed the pseudo-second-order equation and the Langmuir equation very well. The formation of the Cu-containing hydroxylapatite solid solutions ((CuxCa1−x)5(PO4)3(OH)) through adsorption, ion exchange (x = 0.01~0.04), and dissolution-coprecipitation (x = 0.13~0.35) was the dominant process for the Cu (II) removal by the SC–HA/C composite.

Development and Characterization of Bioadsorbents Derived from Different Agricultural Wastes for Water Reclamation: A Review

The presence of dangerous pollutants in different water sources has restricted the availability of this natural resource. Thus, the development of new low-cost and environmentally-friendly technologies is currently required to ensure access to clean water. Various approaches to the recovery of contaminated water have been considered, including the generation of biomaterials with adsorption capacity for dangerous compounds. Research on bioadsorbents has boomed in recent years, as they constitute one of the most sustainable options for water treatment thanks to their abundance and high cellulose content. Thanks to the vast amount of information published to date, the present review addresses the current status of different biosorbents and the principal processes and characterization methods involved, focusing on base biomaterials such as fruits and vegetables, grains and seeds, and herbage and forage. In comparison to other reviews, this work reports more than 60 adsorbents obtained from agricultural wastes. The removal efficiencies and/or maximum adsorption capacities for heavy metals, industrial contaminants, nutrients and pharmaceuticals are presented as well. In addition to the valuable information provided in the literature investigation, challenges and perspectives concerning the implementation of bioadsorbents are discussed in order to comprehensively guide selection of the most suitable biomaterials according to the target contaminant and the available biowastes.

Hexavalent chromium removal from water: adsorption properties of in natura and magnetic nanomodified sugarcane bagasse

Biosorption has become a viable and ecological process in which biological materials are employed as adsorbents for the removal of potentially toxic metals, such as hexavalent chromium, from aqueous matrices. This work proposed the use of in natura (SB) and nanomodified sugarcane bagasse (SB-NP) with ferromagnetic nanoparticles (Fe₃O₄) to adsorb Cr(VI) from water. These materials were analyzed by X-ray Spectroscopy (XRD), Scanning Electron Microscopy (SEM), and Fourier Transform Infrared Spectroscopy (FTIR) to investigate their morphology and interaction with Cr(VI). It was observed the efficient impregnation of magnetite on the SB surface and the presence of functional groups such as O-H, C-H, C=O, C-O-C, C-O, and Fe-O (characteristic of magnetite). The best conditions for Cr(VI) removal in aqueous medium were determined by assessing the pH at the point of zero charge (pH_PZC = 6.1 and 5.8 for SB and SB-NP, respectively), adsorption pH and kinetics, and adsorption capacity. Batch procedures were performed using increasing concentrations of Cr(VI), 10-100 mg/L at pH 1.0, and 30 min of contact time. The adsorbent dose was 10 mg/L, and the experimental adsorption capacities (SC_exp) for SB, NP, and SB-NP were 1.49 ± 0.06 mg/g, 2.48 ± 0.57 mg/g, and 1.60 ± 0.08 mg/g, respectively. All Cr contents were determined by flame atomic absorption spectrometry (FAAS). The pseudo-2nd-order kinetic equation provided the best adjustments with r² 0.9966 and 0.9931 for SB and SB-NP, respectively. Six isotherm models (Langmuir, Freundlich, Sips, Temkin, Dubinin-Radushkevich, and Hill) were applied to the experimental data, and Freundlich, Dubinin-Radushkevich (D-R), and Temkin were the models that best described the experimental sorption process. The binding energy values (E) provided by the D-R model were 0.11 ± 0.25, 0.09 ± 0.20, and 0.08 ± 0.25 kJ/mol, for NP, SB-NP, and SB, respectively, and denote a physical interaction for the studied adsorbate-adsorbent system. The nanomodification of the biomass slightly improved the efficiency for the sorption of Cr(VI) and facilitated the removal of Cr(VI)-containing biosorbents from water medium.

Adsorption study of heavy metals in aqueous solutions aiming at the treatment of contaminated groundwater

This study evaluates the application of the vegetal activated carbon (AC), vegetable AC impregnated with Ag and Cu (0.08% m/m) and cationic Supergel^TM SGC650H resin for adsorption of Fe³⁺ and Pb²⁺ ions in closed and batch system. The best adsorption capacities were obtained by using the cationic resin SGC650H, pH 3, temperature of 30 °C and stirring speed of 100 rpm. Thus, the kinetic and equilibrium experiments, in mono- and bicomponent, were performed using SGC650H resin, wherein the kinetic models of pseudo-first and pseudo-second order presented a good fit to the kinetic data, for mono- and bicomponent, respectively. The Langmuir isotherm adequately represented the monocomponent equilibrium data, showing maximum adsorption capacities values of 7.18 and 4.00 meq g^-1 for Fe³⁺ and Pb²⁺, respectively. An inhibitory effect between the metal species was verified by fitting the modified extended Langmuir isotherm model to the binary equilibrium data, which allowed to predict changes in the surface affinity to the adsorbent by the metal ions. Based on the observed results, the use of SGC650H resin presents great potential for water treatment systems contaminated with heavy metals.

Facile synthesis of graphene oxide-silver nanocomposite for decontamination of water from multiple pollutants by adsorption, catalysis and antibacterial activity

Here in, we presented a facile one-step method for the synthesis of Graphene oxide-silver (GO-Ag) nanocomposite and its applications as a sorbent for the elimination of some toxic pollutants from aqueous medium, as an efficient catalyst in the individual as well as simultaneous reduction reactions of multiple compounds, and as an antibacterial agent for the destruction of some harmful microorganisms existent in wastewater. GO was prepared using a modified Hummers method and Ag nanoparticles were integrated on GO sheets by chemical reduction of Ag⁺ ions on the surfaces of GO sheets. The composition and morphology of the nanocomposite was extensively characterized with elemental dispersive X-ray analysis (EDX), Fourier transform infra-red (FT-IR) spectroscopy, transmission electron microscopy (TEM), field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), and thermal gravimetric analysis (TGA). The GO-Ag nanocomposite demonstrated remarkable adsorption capacities and recyclability for malachite green (MG) and ethyl violet (EV) dyes. Various experimental parameters affecting adsorptive behavior of nanocomposite like temperature, pH, time of contact between dye and adsorbent, and adsorbent dose were evaluated thoroughly. Experimental data was simulated with different adsorption isotherms and kinetic models to evaluate adsorption behavior of both dyes and results confirmed the adsorption of both the dyes to be followed by pseudo 2nd order kinetic model and Langmuir adsorption model. Moreover, adsorbent was regenerated in suitable media for both dyes without any loss in removal efficiency. The catalytic performance for the 2-nitroaniline (2-NA) reduction was investigated in detail. Most importantly, the prepared nanocomposite was found to have potential to adsorb multiple pollutants all together as well as to catalyze the simultaneous reduction of a mixture of dyes (MG, MO, and EV) and 2-NA. An additional advantage of the GO-Ag nanocomposite was its antibacterial activity acquired to the presence of Ag nanoparticles. Two bacterial strains (Gram-negative bacterium, E. coli and the Gram-positive bacterium, S. aureus) were used to test antibacterial activity of composite and the results confirmed the remarkable performance of the nanocomposite in destroying harmful pathogens.

Biosorption of Pb(II) from contaminated water onto Moringa oleifera biomass: kinetics and equilibrium studies

The present study aims at evaluating a batch scale biosorption potential of Moringa oleifera leaves (MOL) for the removal of Pb(II) from aqueous solutions. The MOL biomass was characterized by FTIR, SEM, EDX, and BET. The impact of initial concentrations of Pb (II), adsorbent dosage, pH, contact time, coexisting inorganic ions (Ca²⁺, Na⁺, K⁺, Mg²⁺, CO₃^2-, HCO₃^-, Cl^-), electrical conductivity (EC) and total dissolved salts (TDS) in water was investigated. The results revealed that maximum biosorption (45.83 mg/g) was achieved with adsorbent dosage 0.15 g/100 mL while highest removal (98.6%) was obtained at adsorbent biomass 1.0 g/100 mL and pH 6. The presence of coexisting inorganic ions in water showed a decline in Pb(II) removal (8.5% and 5%) depending on the concentrations of ions. The removal of Pb(II) by MOL decreased from 97% to 89% after five biosorption/desorption cycles with 0.3 M HCl solution. Freundlich model yielded a better fit for equilibrium data and the pseudo-second-order well described the kinetics of Pb(II) biosorption. FTIR spectra showed that -OH, C-H, -C-O, -C = O, and -O-C functional groups were involved in the biosorption of Pb(II). The change in Gibbs free energy (ΔG = -28.10 kJ/mol) revealed that the biosorption process was favorable and thermodynamically driven. The results suggest MOL as a low cost, environment-friendly alternative biosorbent for the remediation of Pb(II) contaminated water.

Agricultural solid waste for sorption of metal ions, part II: competitive assessment in multielemental solution and lake water

Sugarcane bagasse and hydroponic lettuce roots were used as biosorbents for the removal of Cu(II), Fe(II), Mn(II), and Zn(II) from multielemental solutions and lake water, in batch processes. These biomasses were studied in natura (lettuce roots, NLR, and sugarcane bagasse, NSB) and chemically modified with HNO3 (lettuce roots, MLR, and sugarcane bagasse, MSB). The results showed higher adsorption efficiency for MSB and either NLR or MLR. The maximum adsorption capacities (qmax) in multielemental solution for Cu(II), Fe(II), Mn(II), and Zn(II) were 35.86, 31.42, 3.33, and 24.07 mg/g for NLR; 25.36, 27.95, 14.06, and 6.43 mg/g for MLR; 0.92, 3.94, 0.03, and 0.18 mg/g for NSB; and 54.11, 6.52, 16.7, and 1.26 mg/g for MSB, respectively. The kinetic studies with chemically modified biomasses indicated that sorption was achieved in the first 5 min and reached equilibrium around 30 min. Sorption of Cu(II), Fe(II), Mn(II), and Zn(II) in lake water by chemically modified biomasses was 24.31, 14.50, 8.03, and 8.21 mg/g by MLR, and 13.15, 10.50, 6.10, and 5.14 mg/g by MSB, respectively. These biosorbents are promising and low costs agricultural residues, and as for lettuce roots, these showed great potential even with no chemical modification.

Efficiency of sugarcane bagasse-based sorbents for oil removal from engine washing wastewater

This work evaluates the efficiency of sugarcane bagasse-based sorbents in the sorption of oil from engine washing wastewater. The sorbents were obtained from sugarcane bagasse in the natural form (SB-N) and modified with either acetic anhydride (SB-Acet) or 3-aminopropyltriethoxysilane (SB-APTS). The results showed that the sorption capacity of these materials decreased in the following order: SB-APTS > SB-N > SB-Acet. The superior oil sorption capacity observed for SB-APTS was attributed to the polar amino end groups in the silane structure, which acted to increase the hydrophilic character of the fibers. However, all the sorbents obtained in this study were able to clean a real sample of wastewater from engine washing, leading to significant reductions in suspended matter, sediment, anionic surfactants, and turbidity.

Evaluation of Pb (II) biosorption utilizing sugarcane bagasse colonized by Basidiomycetes

The contamination of water resources by metallic ions is a serious risk to public health and the environment. Therefore, a great emphasis has been given to alternative biosorption methods that are based on the retention of aqueous-solution pollutants; in the last decades, several agricultural residues have been explored as low-cost adsorbent. In this study, the ability of Pb (II) biosorption using sugarcane bagasse modified by different fungal species was evaluated. The presence of carbonyl, hydroxyl, and carboxyl groups in the biosorbent was observed by spectroscopy in the infrared region. By scanning electron microscopy, changes in the morphology of modified material surfaces were observed. The highest adsorption capacity occurred at pH 5.0, while the shorter adsorbate-adsorbent equilibrium was at 20 min, and the system followed the pseudo-second-order model. The maximum biosorption in isotherms was found at 58.34 mg g(-1) for modified residue by Pleurotus ostreatus U2-11, and the system followed the Langmuir isotherm. The biosorption process was energetically spontaneous with low desorption values. This modification showed great potential for filters to remove Pb (II) and provide the preservation of water resources and animal health.

Characterization and Properties of Activated Carbon Prepared from Tamarind Seeds by KOH Activation for Fe(III) Adsorption from Aqueous Solution

This research studies the characterization of activated carbon from tamarind seed with KOH activation. The effects of 0.5 : 1–1.5 : 1 KOH : tamarind seed charcoal ratios and 500–700°C activation temperatures were studied. FTIR, SEM-EDS, XRD, and BET were used to characterize tamarind seed and the activated carbon prepared from them. Proximate analysis, percent yield, iodine number, methylene blue number, and preliminary test of Fe(III) adsorption were also studied. Fe(III) adsorption was carried out by 30 mL column with 5–20 ppm Fe(III) initial concentrations. The percent yield of activated carbon prepared from tamarind seed with KOH activation decreased with increasing activation temperature and impregnation ratios, which were in the range from 54.09 to 82.03 wt%. The surface functional groups of activated carbon are O–H, C=O, C–O, –CO₃, C–H, and Si–H. The XRD result showed high crystallinity coming from a potassium compound in the activated carbon. The main elements found in the activated carbon by EDS are C, O, Si, and K. The results of iodine and methylene blue adsorption indicate that the pore size of the activated carbon is mostly in the range of mesopore and macropore. The average BET pore size and BET surface area of activated carbon are 67.9764 Å and 2.7167 m²/g, respectively. Finally, the tamarind seed based activated carbon produced with 500°C activation temperature and 1.0 : 1 KOH : tamarind seed charcoal ratio was used for Fe(III) adsorption test. It was shown that Fe(III) was adsorbed in alkaline conditions and adsorption increased with increasing Fe(III) initial concentration from 5 to 20 ppm with capacity adsorption of 0.0069–0.019 mg/g.

The use of sugar and alcohol industry waste in the adsorption of potentially toxic metals

One of the waste products of the industrial process of the sugar and alcohol agribusiness is filter cake (FC). This waste product has high levels of organic matter, mainly proteins and lipids, and is rich in calcium, nitrogen, potassium and phosphorous. In this work we characterized samples of FC from sugar and alcohol industries located in sugarcane-producing regions in Brazil and assessed the adsorption of potentially toxic metals (Cu(II), Cd(II), Pb(II), Ni(II) and Cr(III)) by this waste in mono- and multi-elemental systems, seeking to use FC as an adsorbent in contaminated environments. The characterization of FCs showed significant differences between the samples and the adsorption studies showed retention of over 90% of potentially toxic metals. In a competitive environment (multi-metallic solution), the FC was effective in adsorbing all metals except lead, but less effective compared to the mono-metallic solution. These results show the potential for use of this residue as an adsorbent in contaminated environments.

Packed bed column studies on lead(II) removal from industrial wastewater by modified Agaricus bisporus

Agaricus bisporus showed best performance in removing Pb(II) with a biosorption capacity of 86.4 mg g(-1) after modification with NaOH. In this work, the removal of Pb(II) from wastewater has been conducted in column mode. The metal removal was dependent on the flow rate, initial metal concentration, and bed height. The experimental data obtained from the biosorption process was successfully correlated with the Bohart-Adams, Thomas, and Yoon-Nelson models. Five biosorption-desorption cycles yielded 95.34%, 92.27%, 90.13%, 86.75%, and 81.52% regeneration, respectively. Pb(II) could be effectively removed from industrial wastewater; some metal ions and organics were also removed concomitantly, and the obtained effluent had characteristics of better quality. The results confirmed that modified A. bisporus could be applied for the removal of heavy metals from industrial wastewater in a continuous column process.

Thermodynamics of Biosorption for Removal of Co(II) Ions by an Efficient and Ecofriendly Biosorbent (Saccharum bengalense): Kinetics and Isotherm Modeling

In this research work, a low-cost biomass derived from the pulp ofSaccharum bengalense(SB) was used as an adsorbent material/biosorbent for the removal of Co(II) ions from aqueous solution. Langmuir, Freundlich Timken, and Dubinin-Radushkevich (D-R) adsorption isotherms have been applied to further define the mechanism of sorption. From the comparison of different adsorption isotherm models, it was found that biosorption of Co(II) by SB followed Langmuir and Freundlich models. The sorption capacity for cobalt ofSaccharum bengalensewas ( mg/g) at 323K. A comparison of kinetic models applied to the adsorption of Co(II) ontoSaccharum bengalensewas evaluated for the pseudo-first-order, pseudo-second-order, Elovich, and intraparticle diffusion and Bangham's kinetics models. It was found that the pseudo-second-order mechanism is predominant. Activation parameters evaluated from thermodynamics and kinetic parameters such as free energy change ,  kJ/mol), enthalpy change ,  kJ/mol), and entropy change ,  kJ/mol) revealed the spontaneous, endothermic, and feasible nature of adsorption process. The results of the present investigation suggested thatSaccharum bengalense(SB) can be used as an environmentally and economically feasible biosorbent for the removal of Co(II) from aqueous solutions.

Effects of impurities on the removal of heavy metals by natural limestones in aqueous systems

Effects of impurities on the removal of heavy metals by natural limestones in aqueous solutions were studied by evaluating various factors including limestone concentration, pH, contact time and temperature. Solutions of Pb(II), Cd(II), Cu(II) and Zn(II), prepared from chloride reagents at a concentration of 10 mg/L, were studied in a batch method. Four natural limestone samples, collected from the Campanian-Maastrichtian limestone beds in Tunisia, were used as adsorbents. Sorption experiments indicated that high removal efficiencies could be achieved. Limestone samples containing impurities, such as silica, iron/aluminum oxides and different kinds of clay minerals, demonstrated enhanced sorption capacity, nearing 100% removal in some cases. Kinetic experiments showed that the sorption of metal ions occurred rapidly at a low coverage stage, and that solutions were nearly at equilibrium after 60 min. Data trends generally fit pseudo-second order kinetic, and intra-particle diffusion, models. The following conditions were found to promote optimum, or near-optimum, sorption of heavy metals: 1) contact time of more than 60 min, 2) pH = 5, 3) >3 g/L limestone concentration and 4) T = 35 °C. The results of this study suggest that the limestones from northern Tunisia, that contain higher amounts of silica and iron/aluminum oxides, are promising adsorbents for the effective removal of toxic heavy metals from wastewaters.