Pseudotumour formation due to tribocorrosion at the taper interface of large diameter metal on polymer modular total hip replacements

Computer-based analysis of the taper connection strength of different revision head and adapter sleeve designs

OBJECTIVES

Ceramic revision heads, equipped with titanium adapter sleeves, are used in femoral head revision in total hip arthroplasty to avoid ceramic fracture due to the damaged taper.

METHODS

A finite element analysis of the taper connection strength of revision heads with varying head diameters combined with adapter sleeves of different lengths was conducted. The influence of various assembly forces, head diameter, and length of the adapter sleeves was evaluated. For two combinations, the pattern of contact pressure was evaluated when applying a simplified joint load (3 kN, 45° load angle). Experimental validation was conducted with 36 mm heads and adapter sleeves in size S, as well as 28 mm heads and adapter sleeves in size XL.

RESULTS

The pull-off force increased with higher assembly forces. Using larger head diameters and adapter sleeves led to decreased pull-off forces, a reduced contact surface, and less contact pressure. The contact pressure showed significant peaks and a diagonal pattern under 45° angle loading when assembly forces were less than 4 kN, and larger adapter sleeves were utilized.

CONCLUSION

A sufficient assembly force should be ensured intraoperatively, especially with an increasing head diameter and adapter sleeve size, as lower assembly forces might lead to reduced taper connection strength.

Investigation of cell-accelerated corrosion (CAC) on the CoCrMo alloy with segregation banding: Hip implant applications

Metal alloy microstructure plays a crucial role in corrosion associated with total hip replacement (THR). THR is a prominent strategy that uses metal implants such as cobalt-chromium-molybdenum (CoCrMo) alloys due to their advantageous biological and mechanical properties. Despite all benefits, these implants undergo corrosion and wear processes in-vivo in a synergistic manner called tribocorrosion. Also, the implant retrieval findings reported that fretting corrosion occurred in-vivo, evidenced by the damage patterns that appeared on the THR junction interfaces. There is no scientific data on the studies reporting the fretting corrosion patterns of CoCrMo microstructures in the presence of specific biological treatments to date. In the current study, Flat-on-flat fretting corrosion set-up was customized and used to study the tribocorrosion patterns of fretting corrosion to understand the role of alloy microstructure. Alloy microstructural differences were created with the implant stock metal's longitudinal and transverse cutting orientations. As a result, the transverse created the non-banded, homogenous microstructure, whereas the longitudinal cut resulted in the banded, non-homogenous microstructure on the surface of the alloy (in this manuscript, the terms homogenous and banded were used). The induced currents were monitored using a three-electrode system. Three different types of electrolytes were utilized to study the fretting corrosion patterns with both homogeneous and banded microstructures: 1. Control media 2. Spent media (the macrophage cell cultured media) 3. Challenged media (media collected after the macrophage was treated with CoCrMo particles). From the electrochemical results, in the potentiostat conditions, the banded group exhibited a higher induced current in both challenged and spent electrolyte environments than in control due to the synergistic activity of CoCrMo particles and macrophage demonstrating more corrosion loss. Additionally, both Bode and Nyquist plots reported a clear difference between the banded and homogeneous microstructure, especially with challenged electrolytes becoming more corrosion-resistant post-fretting than pre-fretting results. The banded microstructure showed a unique shape of the fretting loop, which may be due to tribochemical reactions. Therefore, from the electrochemical, mechanical, and surface analysis data results, the transverse/homogenous/non-banded alloy microstructure groups show a higher resistance to fretting-corrosion damage.

Surface integrity modification of CoCrMo alloy by deep rolling in combination with sub-zero cooling as potential implant application

Alloys made of CoCrMo are well established as implants materials since decades in orthopedic surgery. The good mechanical properties, biocompatibility and especially the corrosion resistance are important rationales for the use of these alloys. Nevertheless, retrieved implants from revision surgery showed the occurrence of abrasion and corrosion. The wear mechanisms and the occurring corrosion processes might be reduced with a functionalization of the surface. The hexagonal phase of the cobalt chromium matrix plays an important role in the surface functionalization. It can be specifically transformed and set during the manufacturing process. One possibility for the induction of the transformation is the use of a deep rolling process in combination with a novel "sub-zero" cooling strategy during machining. The influence of force and temperature during the deep rolling process on the formation of the hexagonal Co-phase is examined in this study. The results from the targeted setting of the hexagonal Co-phase in the subsurface are shown. For this purpose, EBSD studies have been carried out to detect and quantify the proportion of Co-hex phase in the subsurface of the modified alloys. To analyze the mechanical properties, we measured the residual stress and hardness in the near surface layer under conditions close to the application. Furthermore, we performed biological tests to show a potential influence of the modification on the biocompatibility when using the sub-zero cooling approach. We observed no negative effect on the osteoblastic cell line which attached similarly to all tested surfaces. The investigations provide first insights into the potential use of "sub-zero" cooling in modifying orthopedic implant materials, but also the respective limits with regard to the surface functionalization. Deep rolling in combination with an innovative cooling strategy has a great potential to improve the mechanical properties of CoCr28Mo6 wrought alloy, by subsurface hardening and phase transformation.

A novel method to improve femoral head and stem taper stability intraoperatively in total hip arthroplasty - a proof of concept study

BACKGROUND

Mechanically assisted crevice corrosion (MACC) has been associated with the compromised durability and fixation of modular total hip implants, adverse reaction of local tissue, and other undesirable clinical outcomes in total hip arthroplasty (THA). MACC is primarily caused by the relative motion between the femoral head and stem. To minimize the relative motion the taper connection between the two components must be strong enough. The current study addressed the following questions: (1) Does increasing the mass of the femoral stem improve the taper connection strength intraoperatively? (2) Does increasing the mass of the femoral stem reduce the risk of periprosthetic tissue damage intraoperatively?

HYPOTHESIS

Increasing the mass of the femoral stem improve the taper connection strength intraoperatively.

MATERIALS AND METHODS

During the experiment, femoral heads were impacted onto the stem tapers with and without an additional weight attached to the stem. The femoral heads were then pulled off to investigate the strength of the taper connection. The stem displacement and acceleration at impaction were also measured to evaluate the risk of periprosthetic tissue damage.

RESULTS

The results showed that the pull-off force was increased by 24% (p=0.011, n=6) when an additional weight was attached to the stem. The additional weight also reduced the maximum stem acceleration and maximum stem displacement by 37% (p<0.001, n=6) and 14% (p=0.094, n=6), respectively.

DISCUSSION

These findings suggest that the femoral head and stem taper connection strength can be significantly improved and the risk of periprosthetic tissue damage significantly reduced intraoperatively by attaching an additional weight to the stem to increase its mass.

LEVEL OF EVIDENCE

III, comparative in vitro mechanical investigation.

Metal Articulations as a Source of Total Hip Arthroplasty Pain

The consensus systematic risk stratification algorithm from the American Association of Hip and Knee Surgeons, the American Academy of Orthopaedic Surgeons, and The Hip Society summarizes clinical challenges in evaluation and treatment of metal-on-polyethylene total hip arthroplasty (THA) patients with adverse local tissue reaction (ALTR) due to mechanically assisted crevice corrosion (MACC), reviews up-to-date evidence, and identifies the areas for future research in order to provide a useful resource for orthopedic surgeons providing care to these patients. A painful THA has various intrinsic and extrinsic causes. ALTR is one of the intrinsic causes in patients with painful THA. The occurrence of ALTR due to MACC at modular junctions is likely to be multifactorial, including implant, surgical, and patient factors. Therefore, a systematic evaluation needs to involve a focused clinical history, detailed physical examination, laboratory tests, and imaging in order to identify potential differential diagnoses. There should be a low threshold to perform a systematic evaluation of patients with painful non-metal-on-metal THA, including patients with metal-on-polyethylene THA, and modular dual-mobility THA with the CoCr metal acetabular insert, as early recognition and diagnosis of ALTR due to MACC will facilitate initiation of appropriate treatment prior to significant adverse biological reactions. Specialized tests such as blood metal analysis and metal artifact reduction sequence magnetic resonance imaging are important modalities in evaluation and management of ALTR in patients with painful THA.

Parametric analysis of the effect of impaction load on the stability of head-neck junction in total hip arthroplasty

BACKGROUND

Tribocorrosion at head-neck interface is one of the main causes leading to the failure of hip implants in total hip arthroplasty. Impaction load has been acknowledged as one of the key factors influencing the stability of the taper junction. It is understood that the magnitude of impaction force differs from the surgeon to surgeon in primary total hip arthroplasty or revision. Clinically, it is sufficient enough to keep the male and female tapers inseparable utilizing a low impaction, which seems to contradict previous researches. The objective of this study was to investigate the effect of impaction loads on the stability of taper junction during assembly and gaits.

METHODS

A finite element model with 12/14 taper and the taper mismatch of 4' was developed for investigation. The impaction force profiles were collected from surgeon as the inputs, and then the contact mechanics over one or multiple gaits was further analyzed and validated utilizing hip simulator test.

FINDINGS

Impaction force ranging from 200 to 2000 N could provide the same taper connection effect after the first gait due to the secondary seating. As for impaction loads of 3000 N and above, an increased impaction force would lead to the tighter taper connection.

INTERPRETATION

The effect of impaction load on the stability of head-neck junction is a piecewise function, indicating that the stability of taper junction is not affected by different impaction loads and tends to be consistent while its magnitude is below the threshold. Instead, the stability of taper junction is positively correlated with impaction force.

Synthesis of a Lubricant to Mimic the Biorheological Behavior of Osteoarthritic and Revision Synovial Fluid

The rheological properties of synovial fluid (SF) are essential for the friction behavior and wear performance of total joint replacements. Standardized in vitro wear tests for endoprosthesis recommend diluted calf serum, which exhibits substantial different rheological properties compared to SF. Therefore, the in vitro test conditions do not mimic the in vivo conditions. SF samples from osteoarthritis knee patients and patients undergoing knee endoprosthesis revision surgery were compared biochemically and rheologically. The flow properties of SF samples were compared to synthetic fluid constituents, such as bovine serum albumin (BSA) and hyaluronic acid (HA). Interestingly, HA was identified as a significant contributor to shear-thinning. Using the acquired data and mathematical modelling, the flow behavior of human SF was modelled reliably by an adapted adjustment of biorelevant fluid components. Friction tests in a hard/soft bearing (ceramic/UHMWPE) demonstrated that, in contrast to serum, the synthetic model fluids generate a more realistic friction condition. The developed model for an SF mimicking lubricant is recommended for in vitro wear tests of endoprostheses. Furthermore, the results highlight that simulator tests should be performed with a modified lubricant considering an addition of HA for clinically relevant lubrication conditions.

Are Damage Modes Related to Microstructure and Material Loss in Severely Damaged CoCrMo Femoral Heads?

BACKGROUND

Fretting and corrosion in metal-on-polyethylene total hip arthoplasty (THA) modular junctions can cause adverse tissue reactions that are responsible for 2% to 5% of revision surgeries. Damage within cobalt-chromium-molybdenum (CoCrMo) alloy femoral heads can progress chemically and mechanically, leading to damage modes such as column damage, imprinting, and uniform fretting damage. At present, it is unclear which of these damage modes are most detrimental and how they may be linked to implant alloy metallurgy. The alloy microstructure exhibits microstructural features such as grain boundaries, hard phases, and segregation bands, which may enable different damage modes, higher material loss, and the potential risk of adverse local tissue reactions.

QUESTIONS/PURPOSES

In this study, we asked: (1) How prevalent is chemically dominated column damage compared with mechanically dominated damage modes in severely damaged metal-on-polyethylene THA femoral heads made from wrought CoCrMo alloy? (2) Is material loss greater in femoral heads that underwent column damage? (3) Do material loss and the presence of column damage depend on alloy microstructure as characterized by grain size, hard phase content, and/or banding?

METHODS

Surgically retrieved wrought CoCrMo modular femoral heads removed between June 2004 and June 2019 were scored using a modified version of the Goldberg visually based scoring system. Of the total 1002 heads retrieved over this period, 19% (190 of 1002) were identified as severely damaged, exhibiting large areas of fretting scars, black debris, pits, and/or etch marks. Of these, 43% (81 of 190) were excluded for metal-on-metal articulations, alternate designs (such as bipolar, dual-mobility, hemiarthroplasty, metal adaptor sleeves), or previous sectioning of the implant for past studies. One sample was excluded retroactively as metallurgical analysis revealed that it was made of cast alloy, yielding a total of 108 for further analysis. Information on patient age (57 ± 11 years) and sex (56% [61 of 108] were males), reason for removal, implant time in situ (99 ± 78 months), implant manufacturer, head size, and the CoCrMo or titanium-based stem alloy pairing were collected. Damage modes and volumetric material loss within the head tapers were identified using an optical coordinate measuring machine. Samples were categorized by damage mode groups by column damage, imprinting, a combination of column damage and imprinting, or uniform fretting. Metallurgical samples were processed to identify microstructural characteristics of grain size, hard phase content, and banding. Nonparametric Mann-Whitney U and Kruskal-Wallis statistical tests were used to examine volumetric material loss compared with damage mode and microstructural features, and linear regression was performed to correlate patient- and manufacturer-specific factors with volumetric material loss.

RESULTS

Chemically driven column damage was seen in 48% (52 of 108) of femoral heads, with 34% (37 of 108) exhibiting a combination of column damage and imprinting, 12% (13 of 108) of heads displaying column damage and uniform fretting, and 2% (2 of 108) exhibiting such widespread column damage that potentially underlying mechanical damage modes could not be verified. Implants with column damage showed greater material loss than those with mechanically driven damage alone, with median (range) values of 1.2 mm3 (0.2 to 11.7) versus 0.6 mm3 (0 to 20.7; p = 0.03). Median (range) volume loss across all femoral heads was 0.9 mm3 (0 to 20.7). Time in situ, contact area, patient age, sex, head size, manufacturer, and stem alloy type were not associated with volumetric material loss. Banding of the alloy microstructure, with a median (range) material loss of 1.1 mm3 (0 to 20.7), was associated with five times higher material loss compared with those with a homogeneous microstructure, which had a volume loss of 0.2 mm3 (0 to 4.1; p = 0.02). Hard phase content and grain size showed no correlation with material loss.

CONCLUSION

Chemically dominated column damage was a clear indicator of greater volume loss in this study sample of 108 severely damaged heads. Volumetric material loss strongly depended on banding (microstructural segregations) within the alloy. Banding of the wrought CoCrMo microstructure should be avoided during the manufacturing process to reduce volumetric material loss and the release of corrosion products to the periprosthetic tissue.

CLINICAL RELEVANCE

Approximately 30% of THAs rely on wrought CoCrMo femoral heads. Most femoral heads in this study exhibited a banded microstructure that was associated with larger material loss and the occurrence of chemically dominated column damage. This study suggests that elimination of banding from the alloy could substantially reduce the release of implant debris in vivo, which could potentially also reduce the risk of adverse local tissue reactions to implant debris.

Interfacial compliance, energy dissipation, frequency effects, and long-term fretting corrosion performance of Ti-6Al-4V/CoCrMo interfaces

Fretting corrosion in modular orthopedic implants is a well-documented process that may be associated with adverse local tissue reactions, pain, and revisions. Engineering modular junction interfaces to withstand applied fretting motion without surface abrasion could prevent implant degradation and surface damage. Previous work on geometrically modified Ti-6Al-4V/CoCrMo interfaces with increased compliance showed reduced fretting currents and surface damage during short term, variable-load in vitro testing. This study assesses the same interfaces under long-term conditions using an in vitro pin-on-disk fretting corrosion test apparatus. Preliminary variable-load frequency testing of typical control pin geometries showed a frequency-dependent current response, with underlying contact conditions of metal-metal interfaces that remained unchanged. One-million-cycle testing showed diminished fretting currents in all groups by 5 × 10⁵  cycles, but consistently lower currents in the high-compliance group. Corresponding fretting currents and work of fretting measurements of high-compliance pins confirmed that minimal fretting was experienced at the interface, with elastic bending of the pin accounting for almost all applied displacement. Debris generated during testing were composed of titanium and chromium oxides, small amounts of cobalt and molybdenum oxides, and sodium and phosphate originating from the surrounding test solution. Post-test analyses of sample surfaces revealed substantially more surface damage on CoCrMo disks than Ti-6Al-4V pins, thought to be a result of adhesive wear of mixed oxide debris on the pin and abrasion of the disk by the oxide debris layer. Surface damage to high-compliance pins suggests some abrasion is unavoidable with geometric modifications.

Comparison of the Stability of Sandblasted, Large-Grit, and Acid-Etched Treated Mini-Screws With Two Different Surface Roughness Values: A Histomorphometric Study

PURPOSE

To evaluate the effects of 2 different surface roughness values produced by sandblasted, large-grit, and acid-etched treatments at different loading conditions on the stability of mini-screws.

MATERIAL AND METHODS

A total of 56 mini-screws (Group 1; 28 with Ra value of 1 μm, Group 2; 28 with Ra value of 1.5 μm) were inserted into the tibia of fourteen New Zealand rabbits. Surface analysis was performed before the placement of the miniscrews using multi-technique characterization. The mini-screws were loaded with 500 grf after different healing times: unloaded, immediate, 4 and 8 weeks. Resonance frequency analyses were performed immediately after mini-screw placement and at the end of loading. Biomechanical and histomorphometric analyses were also performed at the end of the loading period.

RESULTS

All mini-screws preserved their stability at the end of the loading period. However, the resonance frequency analyses showed higher implant stability quotient scores for 8-week group, unlike the immediate loading and unloaded groups (P < 0.05). According to the infinite focus microscopy results, prolongation of healing time resulted in a greater bone area on the loaded mini-screws in Group 2 (P < 0.05). Similarly, the histomorphometric analysis revealed higher bone-to-implant contact values in the 8-week group. There was no significant difference in the stability between the miniscrews with the Ra values of 1 and 1.5 μm.

CONCLUSIONS

Sandblasted, large-grit, and acid-etched treated mini-screws showed significantly higher stability with healing time under heavy forces. Sandblasted, large-grit, and acid-etched treated mini-screws can be removed without fracture of the screw or the bone surfaces.

On the Formation Mechanism of Column Damage Within Modular Taper Junctions

BACKGROUND

Column damage is a unique degradation pattern observed in cobalt-chromium-molybdenum (CoCrMo) femoral head taper surfaces that resemble column-like troughs in the proximal-distal direction. We investigate the metallurgical origin of this phenomenon.

METHODS

Thirty-two severely damaged CoCrMo femoral head retrievals from 7 different manufacturers were investigated for the presence of column damage and chemical inhomogeneities within the alloy microstructure via metallographic evaluation of samples sectioned off from the femoral heads.

RESULTS

Column damage was found to affect 37.5% of the CoCrMo femoral heads in this study. All the column-damaged femoral heads exhibited chemical inhomogeneities within their microstructures, which comprised of regions enriched or depleted in molybdenum and chromium. Column damage appears as a dissolution of the entire surface with preferential corrosion along the molybdenum and chromium depleted regions.

CONCLUSION

Molybdenum and chromium depleted zones serve as initiation sites for in vivo corrosion of the taper surface. Through crevice corrosion, the degradation spreads to the adjacent non-compositionally depleted areas of the alloy as well. Future improved alloy and processing recipes are required to ensure no chemical inhomogeneity due to segregation of solute elements are present in CoCrMo femoral heads.

A comparison of metal/metal and ceramic/metal taper-trunnion modular connections in explanted total hip replacements

Corrosion and wear are commonly found at the taper-trunnion connection of modular total hip arthroplasty (THA) explanted devices. While metal/metal (M/M) modular taper-trunnion connections exhibit more wear/corrosion than ceramic/metal (C/M) modular taper-trunnion connections, damage is present in both, regardless of material. This study used a combination of assessment techniques including clinical data, visual scoring assessment, optical imaging, profilometry, and x-ray photoelectron microscopy (XPS), to investigate wear mechanisms and damage features at the modular taper-trunnion connection of 10 M/M and 8 C/M explanted THAs. No correlation was found between any demographic variable and corrosion wear and assessment scores. All assessment techniques demonstrated that the stem trunnions had more damage than head tapers for both explant groups and agreed that C/M explants had less corrosion and wear compared to M/M explants. However, visual assessment scores differed between assessment techniques when evaluating the tapers and trunnions within the two groups. Profilometry showed an increase (p <.05) in surface roughness for stem trunnions compared to head tapers for both explant groups. X-ray photoelectron spectroscopy performed on deposits from two M/M explants found chromium and molybdenum carbides beneath the surface while chromium sulfate and aged bone mineral were found on the surface suggesting that the debris is a result of corrosion rather than wear. These results indicate that taper-trunnion damage is more prevalent for M/M explants, but C/M explants are still susceptible to damage. More comprehensive analysis of damage is necessary to better understand the origins of taper-trunnion damage.

Radiographic Risk Factors Associated With Adverse Local Tissue Reaction in Head-Neck Taper Corrosion of Primary Metal-on-Polyethylene Total Hip Arthroplasty

BACKGROUND

Adverse local tissue reactions (ALTRs) in metal-on-polyethylene (MoP) total hip arthroplasty (THA) with head-neck taper corrosion are multifactorial, involving implant and patient factors. This study aimed to identify any potential clinical risk factors associated with failed MoP THA due to head-neck taper corrosion.

METHODS

A series of 146 MoP THA patients was investigated: (1) ALTR (n = 42) on metal artifact sequence MRI and (2) non-ALTR (n = 104). Both cohorts were compared regarding femoral neck shaft angle, acetabular implant orientation, component size, femoral head offset, measurement of medial and vertical femoral offsets, and femoral stem alloy.

RESULTS

The occurrence of ALTR was associated with increased radiographic femoral stem offset (36.0 ± 7.7 mm versus 40.8 ± 7.3 mm, P = 0.008), increased femoral head offset (0.7 ± 3.4 versus 4.5 ± 3.7, P < 0.001), and the use of Ti-12Mo-6Zr-2Fe alloy stems (P = 0.041). The presence of ALTR was notably associated with higher chromium (2.0 versus 0.5 μg/L) and cobalt (7.4 versus 0.7 μg/L, P < 0.001).

DISCUSSION

This study identified increased femoral head and stem offset and the use of Ti-12Mo-6Zr-2Fe alloy stems as risk factors for clinically relevant ALTR due to head-neck taper corrosion in MoP THA patients. This provides evidenced-based practical information for surgeons in identifying "at-risk" symptomatic MoP THA patients with head-neck taper corrosion for systematic risk stratification.

Fretting-corrosion in hip taper modular junctions: The influence of topography and pH levels - An in-vitro study

Contemporary hip implants feature a modular design. Increased reported failure rates associated with the utilization of modular junctions have raised many clinical concerns. Typically, these modular interfaces contain circumferential machining marks (threads or microgrooves), but the effect of the machining marks on the fretting-corrosion behavior of total hip implant materials is unknown. This study reports the effects of microgrooves on the fretting-corrosion behavior of hip implant materials. The flat portions of two cylindrical, polished, CrCrMo alloy pins were loaded horizontally against one rectangular Ti alloy rod. Two surface preparation groups were used for the Ti6Al4V rod (polished and machined). The polished group was prepared using the same methods as the CoCrMo pins. The machined samples were prepared by creating parallel lines on the rod surfaces to represent microgrooves present on the stem tapers of head-neck modular junctions. Newborn calf serum (30 g/L protein content; 37 °C) at pH of levels of 7.6 and 3.0 were used to simulate the normal joint fluid and a lowered pH within a crevice, respectively. The samples were tested in a fretting corrosion apparatus under a 200N normal force and a 1Hz sinusoidal fretting motion with a displacement amplitude of 25 μm. All electrochemical measurements were performed with a potentiostat in a three-electrode configuration. The results show significant differences between machined samples and polished samples in both electrochemical and mechanical responses. In all cases, the magnitude of the drop in potential was greater in the machined group compared to the polished group. The machined group showed a lower total dissipated friction energy for the entire test compared to the polished group. Additionally, the potentiostatic test measurements revealed a higher evolved charge in the machined group compared to the polished group at both pH conditions (pH 7.6 and 3.0). The machined surfaces lowered the overall dissipated friction energy at pH 7.6 compared to pH 3.0, but also compromised electrochemical performance in the tested conditions. Therefore, the role of synergistic interaction of wear and corrosion with surface topographical changes is evident from the outcome of the study. Despite the shift towards higher electrochemical destabilization in the machined group, both polished and machined groups still exhibited a mechanically dominated degradation.

Risk Stratification Algorithm for Management of Head-Neck Taper Tribocorrosion in Patients with Metal-on-Polyethylene Total Hip Arthroplasty: Consensus Statement of the American Association of Hip and Knee Surgeons, the American Academy of Orthopaedic Surgeons, and The Hip Society

Adverse local tissue reactions (ALTRs) were initially reported as complications associated with metal-on-metal (MoM) bearings; however, there is increasing concern regarding the occurrence of adverse local tissue reactions from mechanically assisted crevice corrosion (MACC) at the femoral head-neck junction or between other modular junctions of the implant containing cobalt chromium parts in patients with metal-on-polyethylene (MoP) bearings. ALTR due to MACC at the head-neck junction has primarily been reported in association with cobalt chromium alloy femoral heads. As pain following total hip arthroplasty may have various intrinsic and extrinsic causes, a systematic approach to evaluation (risk stratification algorithm) based on the currently available data is recommended to optimize patient management. Evaluation should begin by ruling out common causes of pain, including component loosening and periprosthetic joint infection. While specialized tests such as blood metal analysis and metal artifact reduction sequence magnetic resonance imaging (MARS MRI) are useful modalities in evaluating for ALTRs, over-reliance on any single investigative tool in the clinical decision-making process should be avoided. There should be a low threshold to perform a systematic evaluation for ALTR due to MACC in patients with metal-on-polyethylene total hip arthroplasty as early recognition and diagnosis is critical, as delays in appropriate treatment initiation may result in soft-tissue damage, which complicates surgical treatment and is associated with a higher risk of complications and poorer patient outcomes.

In Vivo Corrosion of Sleeved Ceramic Femoral Heads: A Retrieval Study

BACKGROUND

The purpose of this study was to evaluate a series of retrieved sleeved ceramic femoral heads used in total hip arthroplasty (THA) and determine qualitative and quantitative damage and corrosion patterns.

METHODS

An IRB-approved implant retrieval database was utilized to identify all sleeved ceramic femoral heads collected from 1995 to 2004. There were 16 implants with an average duration of in situ of 70 months (range, 13-241 months). The femoral stem was known in 14 cases and was titanium alloy in each of those cases. None were revised for metal-related complications. Ten implants (63%) were from primary THAs, and 6 (38%) were from revision THAs. Damage and corrosion were qualitatively graded using a modified Goldberg method. A quantitative assessment was performed with a coordinate measurement machine (CMM).

RESULTS

Among the 16 retrieved implants, 1 (6%) demonstrated severe Grade 4 corrosion, 5 (31%) had moderate Grade 3 corrosion, 5 (31%) had mild Grade 2 corrosion, and 5 (31%) had no visible corrosion at the inner sleeve that interfaces with the stem trunnion. The only case of grade 4 corrosion occurred in the only head-sleeve in the study that was not factory assembled and was mated with a titanium molybdenum zirconium ferrous (TMZF) alloy stem. The mean maximum linear corrosion depth at the taper interface, as measured by the CMM, was 7.7 microns (range, 0.9-32.9 microns).

CONCLUSION

This study is the first to quantify corrosion at the titanium interface of sleeved ceramic femoral heads. Potentially clinically significant damage and corrosion patterns were observed in a few failed retrievals; however, the majority of cases demonstrated minimal or no damage.

Catastrophic failure of femoral stem modular junction when combined with metal-on-metal bearing in comparison to ceramic-on-ceramic: A retrospective cohort study

BACKGROUND

Metal ion release from total hip arthroplasty's (THA) metal-on-metal (MoM) bearing surfaces or head-neck modular junction (trunnionosis) has been identified as a major cause of adverse reaction to metal debris (ARMD). No study has compared the effects of these bearing couples when combined with modular neck femoral stems (MNFS) (i.e. did a modular CoCr have a higher effect than large MoM bearings on whole blood ion concentrations and ARMD). Therefore we did a retrospective comparative analysis of prospectively collected data aiming to: (1) assess the difference in metal ion release between a group of MoM and CoC bearings implanted with a non-cemented MNFS; (2) compare the ARMD and the related revision rates between the two bearing types; (3) compare the patients' HOOS and Harris Hip scores.

HYPOTHESIS

Metal ion levels and complications rate will be higher in MoM group.

METHODS

Thirty hips received the same short MNFS with modular CoCr. Seventeen had CoC bearing (16=36mm) and 13 large diameter head (LDH) MoM bearing (mean=50mm, 44-54mm) Both groups had whole blood Cobalt (Co) and Chromium (Cr) concentrations measurements at last follow up or before revision surgery (if any) and were compared to 41 control individuals without implants. ARMD, revision rates and other complications were censed. Functional outcome differences between operative groups were assessed with HOOS and Harris Hip scores.

RESULTS

Mean whole blood Co and Cr were 1.9μg/L (0.1-10.6 min-max) and 1.2μg/L (0.2-4.6 min-max) in the CoC group and 12.7μg/L (2.5-40.7 min-max) and 8.2μg/L (2.8-40.6 min-max) for MoM group. Controls presented whole blood Co and Cr levels of 0.2μg/L (0.04-0.2 min-max) and 0.6μg/L (0.1-0.7 min-max) respectively. CoC had significantly higher whole blood metal ion concentrations than controls, while MoM had significantly higher concentrations than both (p<0.001). MoM had a 9/13 (69%) revision rate due to ARMD (with stem-neck junction corrosion and wear were present in all cases) while the CoC had none. Functional scores at last follow up did not statistically differ between groups (Harris: CoC=94.1±8.4 vs MoM 91.8±14.8 (p=0.22) and CoC HOOS 90.2±10.7 vs 75.6±21.7 (p=0.08)).

CONCLUSION

In our study, MNFS with CoCr modular neck released metal ion systemically, as shown in CoC THAs, but when combined with MoM LDH bearings, that elevation was significantly higher. In MNFS MoM, these high metal ion levels translated into a dramatic ARMD related revision rate where stem-neck junction corrosion and wear were present in all cases. More research is required to understand the effects of MoM bearing on neck-stem junctions, and its mechanisms of corrosion.

LEVEL OF EVIDENCE

III; retrospective comparative study.

It's worth cleaning - The examination of the female taper could identify a particular cause of trunnionosis at revision 16 years after total hip arthroplasty

Adverse reaction to metal debris (ARMD) is an issue in metal-on-metal (MoM) total hip replacements (THR). It mainly affects large-head MoM THR, whereas 28-32 mm MoM pairings are associated with low long-term revision rates. However, the bearing surface is not necessarily the only cause of metal debris. This report documents with advanced analysis of the retrievals a particular cause of trunnionosis in late failure of a small diameter MoM THR and illustrates the importance of cleaning of the taper when seating the head in THR. A 65-year-old patient was revised due to ARMD 16 years after small diameter MoM THR. Debridement and exchange of the inlay and the head had been performed through an anterior approach. While the cup and the outer surface of the head were accessible to direct analysis by an optical coordinate measuring machine, the female taper had to be analysed indirectly by measuring an imprint. Wear from the cup and the head was within expected low ranges. The analysis of the female taper identified bone fragments, which contributed to trunnionosis. Failure due to ARMD after MoM THR is not necessarily caused by the bearing, but can be due to trunnionosis. Bone fragments within the taper contact in this case highlight the importance of meticulous cleaning of the taper before seating the head, to avoid trunnionosis.

A comparative study on the physicochemical characteristics of nanoparticles released in vivo from CoCrMo tapers and cement-stem interfaces of total hip replacements

The good biocompatibility and corrosion resistance of the bulk CoCrMo alloy has resulted in it being used in the manufacture of implants and load bearing medical devices. These devices, however, can release wear and corrosion products which differ from the composition of the bulk CoCrMo alloy. The physicochemical characteristics of the particles and the associated in vivo reactivity are dictated by the wear mechanisms and electrochemical conditions at the sites of material loss. Debris released from CoCrMo hip bearings, taper junctions, or cement-stem interfaces can, therefore, have different chemical and morphological characteristics, which provide them with different in vivo toxicities. Here, we propose to assess and compare the characteristics of the particles released in vivo from CoCrMo tapers and cement-stem interfaces which have received less attention compared to debris originating from the hip bearings. The study uses state-of-art characterization techniques to provide a detailed understanding of the size, morphology, composition, and chemistry of the particles liberated from the wear and corrosion flakes from revised hip replacements, with an enzymatic treatment. The phase analyses identified Cr₂ O₃ nanoparticles released from tapers and cement-stem interfaces, whose composition did not vary with origin or particle morphology. The size distributions showed significantly smaller particles were released from the stems, compared to the particles originating from the corresponding tapers. The investigation demonstrates that the tribocorrosive processes occurring at the taper and stem interfaces both result in Cr₂ O₃ nanoparticle formation.

Fretting corrosion of Si3 N4 vs CoCrMo femoral heads on Ti-6Al-V trunnions

Fretting corrosion at the head-neck taper junction was compared between silicon nitride (Si₃ N₄ ) and commercially available cobalt chrome (CoCrMo) femoral heads on titanium (Ti-6Al-4V) trunnions. An electrochemical setup was used to capture the fretting currents (characterized by oxide abrasion and repassivation) during cyclic loading. Onset load, pull-off force (disassembly load), short term and long term (1 million cycles) fretting currents were used to compare the fretting corrosion performance between the test group (Si₃ N₄ /Ti-6Al-4V) and the control group (CoCrMo/Ti-6Al-4V). Incremental cyclic fretting corrosion tests showed that the Si₃ N₄ /Ti-6Al-4V combination had statistically lower (P < .05) average fretting current of 0.189 µA (SD = 0.114 µA) compared to 0.685 µA (SD = 0.630 µA) for CoCrMo/Ti-6Al-4V for cyclic load of 3200 N. Similarly, for the one million cycle fretting corrosion tests, the Si₃ N₄ /Ti-6Al-4V couples had statistically lower (P < .05) average current (0.048 µA, SD = 0.025 µA) vs CoCrMo/Ti-6Al-4V couples (0.366 µA, SD = 0.143 µA). The Si₃ N₄ heads also had higher onset loads (P < .05) for fretting (vs CoCrMo, 2200 N vs 1740 N) indicating a difference in surface contact mechanics between the two groups. Scanning electron microscopy with energy dispersive spectroscopy confirmed material transfer from the trunnions to the heads for both groups tested, and from head to trunnion for the CoCrMo heads. Minimal Si₃ N₄ transfer was noted. The electrochemical, mechanical, and microscopic inspection data supported the hypothesis that Si₃ N₄ /Ti-6Al-4Vcombination had better fretting corrosion performance compared to CoCrMo/Ti-6Al-4V.

What Is the Risk of THA Revision for ARMD in Patients with Non-metal-on-metal Bearings? A Study from the Australian National Joint Replacement Registry

BACKGROUND

There are increasing reports of corrosion between the femoral head and trunnion in primary conventional THA, resulting in metal particulate release often termed trunnionosis. There may be heightened awareness of this condition because of severe soft-tissue reactions initially thought to be solely attributable to prostheses with a metal-on-metal (MoM) bearing surface. It is unclear what percentage of revisions for THA with non-MoM bearing surfaces can be attributed to trunnionosis and to what extent adverse reaction to metal debris (ARMD) seen with MoM bearings may also be seen with other bearing surfaces in THA.

QUESTIONS/PURPOSES

We analyzed data from a large national registry to ask: (1) What is the revision risk for the indication of ARMD in patients with conventional THA and modern non-MoM bearing surfaces such as metal or ceramic-on-cross-linked polyethylene (XLPE) or ceramic-on-ceramic? (2) What prosthesis factors are associated with an increased risk of such revision? (3) What is the relative revision risk for ARMD in THAs with large-head MoM bearings, small-head MoM bearings, and non-MoM modern bearing surfaces?

METHODS

The Australian Orthopaedic Association National Joint Replacement Registry (AOANJRR) longitudinally maintains data on all primary and revision joint arthroplasties, with nearly 100% capture. The study population included all THAs using modern bearing surfaces (defined as metal or ceramic heads-on-XLPE and ceramic-on-ceramic bearing couples) revised because of ARMD between September 1999 and December 2018. Prostheses with modular necks were excluded. The cumulative percent revision (CPR) because of ARMD was determined. The study group consisted of 350,027 THAs with a modern bearing surface, 15,184 THAs with a large-head MoM bearing (≥ 36 mm), and 5474 THAs with a small head MoM bearing (≤ 32 mm). The patients in the group who received the modern bearing surfaces were slightly older than the patients in the groups who received the large- and small-head bearing surfaces, with a mean age 68 years (SD 12) versus a mean age 63 years (SD 12), and a mean age 62 years (SD 11), respectively. There was a higher proportion of women in the modern bearing surface group; 55% (193,312 of 350,027), compared with 43% (6497 of 15,184) in the large-head MoM group and 50% (2716 of 5474) in the small-head MoM group. The outcome measure was the CPR, which was defined using Kaplan-Meier estimates of survivorship to describe the time to the first revision for ARMD at 17 years. Hazard ratios (HR) from Cox proportional hazards models, adjusting for age and sex, were performed to compare the revision rates among groups. The registry defines a revision as a reoperation of a previous hip arthroplasty in which one or more of the prosthetic components is replaced or removed, or one or more components is added.

RESULTS

The CPR for ARMD for patients with a modern bearing surface at 17 years was 0.1% (95% confidence interval 0.0 to 0.1). After controlling for age and sex, we found that cobalt chrome heads, two specific prostheses (Accolade® I and M/L Taper), and head sizes ≥ 36 mm were associated with an increased risk of revision for ARMD. Metal-on-XLPE had a higher risk of revision for ARMD than ceramic-on-ceramic or ceramic-on-XLPE (HR 3.4 [95% CI 1.9 to 6.0]; p < 0.001). The Accolade 1 and the M/L Taper stems had a higher risk of revision than all other stems (HR, 8.3 [95% CI 4.7 to 14.7]; p < 0.001 and HR 14.4 [95% CI 6.0 to 34.6]; p < 0.001, respectively). Femoral stems with head sizes ≥ 36 mm had a higher rate of revision for ARMD than stems with head sizes ≤ 32 mm (HR 3.2 [95% CI 1.9 to 5.3]; p < 0.001).Large-head MoM bearings had a greater increase in revision for ARMD compared with modern bearing surfaces. The CPR for patients with a large-head MoM bearing at 17 years for ARMD was 15.5% (95% CI 14.5 to 16.6) and it was 0.1% for modern bearing surfaces (HR 340 [95% CI 264.2 to 438.0]; p < 0.001). Modern bearing surfaces likewise had a lower HR for revision for ARMD than did THAs with small-head MoM bearings, which had a 0.9% (95% CI 0.7 to 1.4) CPR compared with modern bearings from 0 to 9 years (HR 10.5 [95% CI 6.2 to 17.7]; p < 0.001).

CONCLUSIONS

The revision risk for ARMD with modern bearing surfaces in THA is low. The Accolade 1 and the M/L Taper stem have a higher risk of revision for ARMD and cobalt-chrome heads, and head sizes ≥ 36 mm have a higher rate of revision than ≤ 32 mm head sizes. ARMD is a rare failure mode for THA with non-MoM bearings, but in patients presenting with unexplained pain with no other obvious cause, this diagnosis should be considered and investigated further.

LEVEL OF EVIDENCE

Level III, therapeutic study.

Influence of Different Damage Patterns of the Stem Taper on Fixation and Fracture Strength of Ceramic Ball Heads for Total Hip Replacement

Background

Modularity finds frequent application in total hip replacement, allowing a preferable individual configuration and a simplified revision by retaining the femoral stem and replacing the prosthetic head. However, micromotions within the interface between the head and the stem taper can arise, resulting in the release of wear debris and corrosion products. The aim of our experimental study was to evaluate the influence of different taper damages on the fixation and fracture stability of ceramic femoral heads, after static and dynamic implant loading.

Methods

Ceramic ball heads (36 mm diameter) and 12/14 stem tapers made of titanium with various mild damage patterns (intact, scratched, and truncated) were tested. The heads were assembled on the taper with a quasistatic load of 2 kN and separated into a static and a dynamic group afterwards. The dynamic group (n = 18) was loaded over 1.5 million gait cycles in a hip wear simulator (ISO 14242-1). In contrast, the static group (n = 18) was not mechanically loaded after assembly. To determine the taper stability, all heads of the dynamic and static groups were either pulled off (ASTM 2009) or turned off (ISO 7206-16). A head fracture test (ISO 7206-10) was also performed. Subsequent to the fixation stability tests, the taper surface was visually evaluated in terms of any signs of wear or corrosion after the dynamic loading.

Results

In 10 of the 18 cases, discoloration of the taper was determined after the dynamic loading and subsequent cleaning, indicating the first signs of corrosion. Pull-off forces as well as turn-off moments were increased between 23% and 54% after the dynamic loading compared to the unloaded tapers. No significant influence of taper damage was determined in terms of taper fixation strength. However, the taper damage led to a decrease in fracture strength by approximately 20% (scratched) and 40% (truncated), respectively.

Conclusion

The results suggest that careful handling and accurate manufacturing of the stem taper are crucial for the ceramic head fracture strength, even though a mild damage showed no significant influence on taper stability. Moreover, our data indicate that a further seating of the prosthetic head may occur during daily activities, when the resulting hip force increases the assembly load.

In vivo corrosion and damages in modular shoulder prostheses

Wear and corrosion at taper junctions of orthopaedic endoprostheses remain of great concern and are associated with adverse clinical reactions. Whereas tribocorrosion of hip tapers was extensively investigated, there is only little knowledge regarding the clinical performance of modular total shoulder prostheses. This retrieval study evaluated 35 modular taper junctions of anatomical shoulder explants using stereomicroscopy, confocal microscopy, as well as optical and scanning electron microscopy to determine the damage modes as well as the effects of taper topography and alloy microstructure. Among all humeral head tapers, 89% exhibited material degradation. Different overlapping wear mechanisms were identified such as plastic deformation, adhesive material transfer, microploughing, and fretting damage. Only CoCrMo cast alloy heads showed a susceptibility to electrochemically dominated fretting in comparison to CoCrMo wrought alloy. Moreover, corundum blasted stem tapers show a significantly increased incidence rate for microploughing. To date, this is the most comprehensive study on the damage types of modular taper junctions of anatomical shoulder arthroplasty proving the existence of fretting even on less weight-bearing implants. This study revealed critical fretting factors, such as the surface finish and the alloy type that are essential for the development of countermeasures that avoid any taper corrosion.

The Accolade TMZF stem fulfils the demands of modern stem design: Minimum 5-year survival in a cohort of 937 patients

PURPOSE

Modern hip stem design includes a prosthesis that has a predictable outcome in all total hip arthroplasty (THA) patients, regardless of approach, surgeon or patient characteristics. Introduction without a learning curve and, in cases of problems, the possibility for a simple revision are other prerequisites. The purpose of this study is to evaluate whether the Accolade TMZF stem (Stryker Orthopedics, Mahwah, New Jersey, USA) is suitable to fulfil these demands. We report our mid-term survival of the Accolade TMZF hip stem in all patients from the first implantation at our institute.

METHODS

From the start of using the Accolade TMZF stem (March 2009) until February 2011, 937 THA were performed by 12 surgeons using a posterolateral or anterolateral approach. Survival of the stem was calculated using Kaplan-Meier analysis. Effect of approach, patient age and comorbidity were analysed with a Cox proportional hazards' model. The learning effect was determined by comparing the number of revisions in the surgeons' first 20 THAs with their next 30 THAs and the subsequent THAs.

RESULTS

At 5 years, cumulative stem survival was 97.9% based on revisions for all reasons and 98.8% with aseptic loosening as endpoint. We found no effect of surgical approach, patient age or comorbidity on stem survival. No learning effect was found.

CONCLUSION

The Accolade TMZF stem fulfilled the demands of modern stem design.

Diagnosis and Management of Adverse Reactions to Metal Debris

Modern total hip arthroplasty implants have incorporated modularity into their designs, providing the benefits of intraoperative flexibility and the ability to exchange the femoral heads in the future if necessary. However, this feature has unfortunately predisposed patients to the effects of corrosion, potentially resulting in adverse local tissue reactions (ALTR) and even systemic effects. A thorough understanding of the science of corrosion is important for the treating surgeon so that they can understand the underlying pathology, quickly diagnose the condition of ALTR, and risk stratify their patients to determine the best method of treatment. Revision surgery is not always necessary in cases of trunnionosis or ALTR, but the results of revision surgery are generally favorable.

Severe Wear and multiple Pseudotumor formation due to revision for ceramic head breakage after ceramic-on-ceramic Total hip arthroplasty: a case report

Background

Head breakage is a serious complication following total hip arthroplasty when using Ceramic on Ceramic bearings surfaces. There is still in controversy about the selection of bearing surfaces when conducting revision surgery.

Case presentation

We describe the case of a fifty-year-old man who had undergone right total hip arthroplasty (THA) with ceramic-on-ceramic prostheses in 2011. After a fall 6 years after the primary procedures, radiographs suggested a ceramic head breakage for revision THA with exchange of metal-on-polyethylene bearing. However, 8 months later, severe metallosis and multiple pseudotumor was confirmed in pelvis and surrounding hip after re-revision THA with ceramic-on-polyethylene prostheses. Analysis of the serum metal ion indicated massive wear of the metal head and erosion of the stem neck and taper.

Conclusions

This case vividly demonstrates metal bearings should be avoided and revision with complete synovectomy and thorough debridement should be performed whenever possible for a fractured ceramic bearing.

Trunnion Corrosion in Total Hip Arthroplasty-Basic Concepts

There has been increased interest in the role of corrosion in early implant failures and adverse local tissue reaction in total hip arthroplasty. We review the relationship between the different types of corrosion in orthopaedic surgery including uniform, pitting, crevice, and fretting or mechanically assisted crevice corrosion (MACC). Passive layer dynamics serves a critical role in each of these processes. The femoral head-neck trunnion creates an optimal environment for corrosion to occur because of the limited fluid diffusion, acidic environment, and increased bending moment.

Design, Material, and Seating Load Effects on In Vitro Fretting Corrosion Performance of Modular Head-Neck Tapers

BACKGROUND

The short-term corrosion and micromechanical behavior of 32 unique head-neck taper design/material/assembly conditions was tested using an incremental cyclic fretting corrosion (ICFC) test method previously developed.

METHODS

Seven materials, design, and simulated surgical parameters were evaluated, each being assigned 2 conditions for testing, using a 2^7-2 (7 factor, quarter factorial) design of experiments test matrix. The factors explored were (1) seating load, (2) head-neck offset, (3) material combination, (4) taper diameter, (5) taper roughness, (6) angular mismatch/engagement, and (7) taper length. Each sample underwent assembly, ICFC testing, pull off.

RESULTS

Low seating load and high head offset correlated with increased fretting corrosion (P < .05). High head offset also contributed to a lower onset load for fretting current and higher micromotion (P < .05). Head subsidence measured over the ICFC test for samples seated at 100 N was significantly higher than samples seated at 4000 N. Micromotion for 12-mm head offsets was statistically higher than samples with a 1.5-mm head offset. A number of interactive effects were observed. For example, samples seated at 4000 N were less sensitive to head offset than samples seated at 100 N in terms of the resulting fretting current.

CONCLUSION

Taper locking position, material combination, taper engagement length, taper roughness, and taper dimensions all had weak or no correlation with fretting current and taper micromotion. This test method and experimental design is a versatile means of assessing potential new taper designs in the future.

Do oxidized zirconium heads decrease tribocorrosion in total hip arthroplasty? A study of retrieved components

AIMS

The aim of this study was to evaluate fretting and corrosion in retrieved oxidized zirconium (OxZr; OXINIUM, Smith & Nephew, Memphis, Tennessee) femoral heads and compare the results with those from a matched cohort of cobalt-chromium (CoCr) femoral heads.

PATIENTS AND METHODS

A total of 28 OxZr femoral heads were retrieved during revision total hip arthroplasty (THA) and matched to 28 retrieved CoCr heads according to patient demographics. The mean age at index was 56 years (46 to 83) in the OxZr group and 70 years (46 to 92) in the CoCr group. Fretting and corrosion scores of the female taper of the heads were measured according to the modified Goldberg scoring method.

RESULTS

The OxZr-retrieved femoral heads showed significantly lower mean corrosion scores than the CoCr heads (1.3 (1 to 2.75) vs 2.1 (1 to 4); p < 0.01). Mean fretting scores were also significantly lower in the OxZr cohort when compared with the CoCr cohort (1.3 (1 to 2) vs 1.5 (1 to 2.25); p = 0.02). OxZr heads had more damage in the proximal region compared with the distal region of the head. Location had no impact on damage of CoCr heads. A trend towards increased corrosion in large heads was seen only in the CoCr heads, although this was not statistically significant.

CONCLUSION

Retrieval analysis of OxZr femoral heads showed a decreased amount of fretting and corrosion compared with CoCr femoral heads. OxZr seems to be effective at reducing taper damage. Cite this article: Bone Joint J 2019;101-B:386-389.

Hip simulator testing of the taper-trunnion junction and bearing surfaces of contemporary metal-on-cross-linked-polyethylene hip prostheses

Adverse reaction to metal debris released from the taper-trunnion junction of modular metal-on-polyethylene (MoP) total hip replacements (THRs) is an issue of contemporary concern. Therefore, a hip simulator was used to investigate material loss, if any, at both the articulating and taper-trunnion surfaces of five 32-mm metal-on-cross-linked-polyethylene THRs for 5 million cycles (Mc) with a sixth joint serving as a dynamically loaded soak control. Commercially available cobalt-chromium-molybdenum femoral heads articulating against cross-linked polyethylene (XLPE) acetabular liners were mounted on 12/14 titanium (Ti6Al4V) trunnions. Weight loss (mg) was measured gravimetrically and converted into volume loss (mm³ ) for heads, liners, and trunnions at regular intervals. Additionally, posttest volumetric wear measurements of the femoral tapers were obtained using a coordinate measuring machine (CMM). The surface roughness (Sa) of femoral tapers was measured posttest. After 5 Mc, the mean volumetric wear rate for XLPE liners was 2.74 ± 0.74 mm³ /Mc. The CMM measurements confirmed material loss from the femoral taper with the mean volumetric wear rate of 0.045 ± 0.024 mm³ /Mc. The Sa on the worn area of the femoral taper showed a significant increase (p < 0.001) compared with the unworn area. No other long-term hip simulator tests have investigated wear from the taper-trunnion junction of contemporary MoP THRs. © 2019 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 108B:156-166, 2020.

Determination of local micromotion at the stem-neck taper junction of a bi-modular total hip prosthesis design

High rates of clinical complications with bi-modular hip prostheses are attributed to failure of the stem-neck taper junction. Taper wear analyses have shown extensive material loss as a result of corrosion, potentially initiated by micromotion. The purpose of the study was to determine the amount of micromotion at this junction for different loading, assembly and material conditions. Micromotion between the neck adapter (CoCr29Mo6-alloy) and the stem (TiMo12Zr6Fe2-alloy; both Rejuvenate, Stryker) within the taper junction of a bi-modular hip stem were determined by image matching analysis of consecutively recorded images through windows in the stem component. A finite element model was used to determine the micromotion in the taper regions outside the windows and validated with the measured micromotion. With the model, the influence of the load amplitude, assembly force and component materials were then investigated. Determined micromotion (14-79 µm) by far exceeded critical values (5 µm) associated with the onset of fretting corrosion. Increasing assembly forces achieved a significant reduction in micromotion. The numerical model revealed insufficient assembly to cause the neck to perform rocking motions under load, repetitively changing taper contact in combination with gap opening, which facilitates fluid ingress into the junction. Changing the stem material to a stiffer Ti-alloy achieved a reduction of the micromotion of about 30%. This study emphasises the high importance of material selection, assembly force and loading on the susceptibility of bi-modular hip stems to fretting and crevice corrosion. These findings can serve to explain the increased rate of clinically reported problems with this particular prosthesis design.

Clinical Impact of Trunnion Wear After Total Hip Arthroplasty

Trunnionosis, characterized by corrosion and fretting of the taper, is a well-known entity commonly demonstrated in retrieval specimens. While there have been a number of recent reports regarding the potential for adverse local tissue reactions related to trunnionosis, it remains a relatively infrequent cause for failure of total hip replacement implants. A number of factors, including both biomechanical and bioelectrochemical factors, have a known impact on the development and severity of trunnionosis. Furthermore, specific implant design and material-related factors have been shown to influence the risk of trunnionosis leading to adverse local tissue reactions. Retention of a well-fixed femoral stem, in spite of corrosion of the male taper junction, is acceptable in the majority of cases. A ceramic head, often in combination with a titanium adaptor sleeve, is the most common replacement reported in the current literature to treat trunnionosis. In patients with modular-neck total hip replacements, revision of the femoral stem is likely required if corrosion at the modular neck-stem junction is encountered.

Differential proteomic analysis of synovial fluid from hip arthroplasty patients with a pseudotumor vs. Periprosthetic osteolysis

Adverse tissue reactions to metal implants, including pseudotumors, can compromise implant functionality and survivorship. The identification of specific proteins in the synovial fluid (SF) of hip arthroplasty patients with a pseudotumor may lead to a better understanding of the underlying pathomechanisms. The objective of the present study was to compare the protein content of SF from patients with a short-term metal-on-metal hip implant associated with a pseudotumor and patients with a long-term metal-on-polyethylene hip implant associated with periprosthetic osteolysis. Discovery proteomics was used to identify differentially abundant proteins in albumin-depleted SF. In toto, 452 distinct proteins (present in at least half of the patients in one or both groups) were identified. Thirty of these 452 proteins were differentially abundant between the two groups, including two potential biomarkers: 6-phosphogluconate dehydrogenase (which plays a major protective role against oxidative stress) for the pseudotumor group, and scavenger receptor cysteine-rich type 1 protein M130 (which is involved in low-grade inflammation) for the periprosthetic osteolysis group. Other differentially abundant proteins identified suggest the presence of an adaptive immune response (particularly a type-IV hypersensitivity reaction), necrosis, and greater oxidative stress in patients with a pseudotumor. They also suggest the presence of an innate immune response, oxidative stress, tissue remodeling, and apoptosis in both patient groups, although differences in the specific proteins identified in each group point to differences in the pathomechanisms. Overall, results provide insights into the molecular mechanisms underlying metal-related pseudotumors and periprosthetic osteolysis, and may ultimately help elucidate pseudotumor etiology and assess the risk that asymptomatic pseudotumors will develop into an aggressive lesion. © 2018 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 36:1849-1859, 2018.

Retrieval Analysis of Large-Head Modular Metal-on-Metal Hip Replacements of a Single Design

BACKGROUND

There are limited publications examining modular metal-on-metal (MoM) total hip implants in which a comprehensive analysis of retrieved components is performed. This study examines 24 retrieved modular MoM implants from a single manufacturer and compares retrieval analytics; bearing surface damage, wear, and modular taper corrosion against patient, surgical and implant characteristics to elucidate significant associations.

METHODS

Clinical, patient, and surgical data were collected including age, body mass index, blood metal ion levels, and cup inclination. Damage assessment was performed visually in addition to surface profilometry. Acetabular liners and femoral heads were measured for volumetric wear. Femoral head taper bores were similarly measured for material removal due to corrosion and fretting.

RESULTS

Patients with MoM-related reasons for revision showed significantly higher levels of blood metal ion levels. Bearing wear was strongly associated with blood metal ion levels and was significantly increased in cups placed more vertically. Younger patients tended to have higher body mass indices as well as poorer cup placement.

CONCLUSION

This work details a broad range of analyses on a series of modular MoM total hip implants from a single manufacturer of which there are few published studies. Acetabular cup inclination angle was deemed a primary cause of revision surgery through increased MoM wear, high metal ion levels in the blood, and subsequent adverse local tissue reactions. Heavy patients can increase the surgical difficulty which was shown to be related to poor cup placement in this cohort.

Investigation of nano-sized debris released from CoCrMo secondary interfaces in total hip replacements: Digestion of the flakes

The in vivo release of wear debris and corrosion products from the metallic interfaces of total hip replacements is associated with a wide spectrum of adverse body reactions and systemic manifestations. The origin of debris and the electrochemical conditions at the sites of material loss both play a role in determining the physicochemical characteristics of the particles, and thus influence their in vivo reactivity. Debris retrieved from revised CoCrMo tapers and cement-stem interfaces consists of heterogeneous flakes that comprise mechanically mixed metal particles, corrosion products and organic material. Detailed investigation of the size and composition of the metal debris contained within these composites requires the digestion of the flakes to release the small metal particles. Here, we compare alkaline and enzymatic digestion methods that both aim to fragment the flakes and reveal their smallest building blocks. The characterization of debris cleaned with both methods revealed crystalline Cr oxide nanoparticles and clusters. Comparison between the treatments showed that the alkaline method is more efficient in fragmenting the flakes and provided cleaner and generally smaller nanoparticles than exhibited in debris released with the enzymatic treatment. The provision of cleaner nanoparticles from the alkaline method also allows the physicochemical properties of the particles to be more clearly identified. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 107B: 424-434, 2019.

Fretting and Corrosion Damage in Retrieved Metal-on-Polyethylene Modular Total Hip Arthroplasty Systems: What Is the Importance of Femoral Head Size?

BACKGROUND

Fretting and corrosion at the modular femoral head-femoral neck (taper) interface have been reported in retrieved total hip arthroplasty (THA) prostheses. This study investigated associations among implant design, radiographic factors, and patient factors with corrosion and fretting at the taper interface in retrieved metal-on-polyethylene modular THA prostheses.

METHODS

Ninety-two retrieved primary metal-on-polyethylene THA implants were evaluated and graded for fretting, corrosion, and damage at the taper interface, including the femoral stem trunnion and femoral head. Preoperative radiographs were assessed for osteolysis and femoral stem alignment; and medical records were reviewed for demographic data.

RESULTS

Male patients had greater head corrosion (P = .037), patient age at revision had a weak, negative correlation with trunnion corrosion (ρ = -0.20, P = .04), and both body mass index and duration of implantation had weak, positive correlations with head fretting (ρ = 0.26, P = .01 and ρ = 0.33, P = .001, respectively). A weak, negative correlation was found between femoral head size and both head fretting and head corrosion (ρ = -0.26, P = .007 and ρ = -0.21, P = .028, respectively), and a weak, positive correlation was found between head offset and trunnion fretting (ρ = 0.23, P = .030). Varus femoral stem alignment was associated with greater head fretting (P = .038).

CONCLUSION

Larger femoral head sizes were correlated with less severe head corrosion and head fretting, with 28-mm heads exhibiting more moderate-to-severe damage. Other factors, such as head-taper engagement and geometry, rather than head size, may affect rates of corrosion and fretting damage at the taper interface.

Does the Additional Articulation in Retrieved Bipolar Hemiarthroplasty Implants Decrease Trunnionosis Compared to Total Hip Arthroplasty?

BACKGROUND

Trunnionosis at the modular head-neck taper interface in metal-on-polyethylene total hip arthroplasty (MoP THA) has been shown to occur, and represents a potential mode of MoP THA failure. The purpose of the present investigation is to elucidate differences in fretting and corrosion at the head-neck taper interface of prostheses retrieved from bipolar hemiarthroplasty (BH) and MoP THA.

METHODS

A retrieval analysis of BH and MoP THA prostheses featuring a single taper design from a single manufacturer and in vivo for a minimum 2 years was performed. Fifteen femoral heads of 28-mm diameter and corresponding femoral stems retrieved from BH were compared with MoP THA implants matched based on time in vivo and head length (28 mm, -3 mm to 28 mm, +8 mm). Fretting and corrosion damage scoring was completed under stereomicroscopic visualization.

RESULTS

Femoral head bore tapers retrieved from BH exhibited decreased overall fretting (P = .02), when compared to those retrieved from MoP THA. Total corrosion scores for all retrieved implants were positively correlated with implantation time (ρ = 0.54, P < .02).

CONCLUSION

Femoral heads retrieved from BH exhibit decreased fretting damage compared to those retrieved from MoP THA. The added articulation in BH implants may decrease torque produced at the head-neck taper junction, thereby decreasing fretting. Increased fretting damage in implants from MoP THA is not associated with increased corrosion in 28-mm heads of this taper design. The longer a BH or MoP THA prosthesis is implanted, the greater the risk of damage due to corrosion.

Effect of impact assembly on the interface deformation and fretting corrosion of modular hip tapers: An in vitro study

Wear and corrosion at the modular head-neck junction has been recognised to be a potential clinical concern, with multiple reports on adverse local tissue reactions and subsequent early failure of metal-on-metal hip replacements. Furthermore, reports on head-neck taper corrosion are also being described with conventional metal-on-polyethylene bearings. Manufacturing tolerances, surgical technique, non-axial alignment, material combination, high frictional torque and high bending moment have all been implicated in the failure process. There is limited guidance on the force of impaction with which surgeons should assemble modular hip prostheses. This study aims to investigate the effect of impaction force on the deformation and corrosion of modular tapers. Short neck tapers with high surface roughness (average R_z  = 16.58 μm, R_a  = 4.14μm) and long neck tapers with low surface roughness (average R_z  = 3.82 μm, R_a  = 0.81μm), were assembled with CoCrMo alloy heads (smooth finish) under controlled conditions with 2, 4 or 8 kN of impaction force. Material combinations tested included CoCrMo-head/CoCrMo-neck and CoCrMo-head/Ti-6Al-4V-neck. Assessment of surface deformation before and after impaction was made using surface profilometry. Measurement of fretting current during sinusoidal cyclic loading evaluated mechanically assisted corrosion for each assembly load during short-term cyclic loading (1000-cycles) and long-term cyclic loading (5 million-cycles). Deformation on head and neck tapers increased with assembly load. Fretting currents during short term simulation testing showed significantly lower currents (p < 0.05), in 8 kN assemblies when compared to 2 and 4 kN, especially for the short-rough tapers. Long-term simulator testing demonstrated a progressive reduction in fretting corrosion for samples impacted with 4 and 8 kN; however, this reduction was greater for samples impacted at 8 kN even at the start of testing. Based on our results, surgeons could minimise mechanically assisted crevice corrosion by using higher impact loads when assembling the head to the stem in total hip arthroplasty. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 36:405-416, 2018.

Alloy Microstructure Dictates Corrosion Modes in THA Modular Junctions

BACKGROUND

Adverse local tissue reactions (ALTRs) triggered by corrosion products from modular taper junctions are a known cause of premature THA failure. CoCrMo devices are of particular concern because cobalt ions and chromium-orthophosphates were shown to be linked to ALTRs, even in metal-on-polyethylene THAs. The most common categories of CoCrMo alloy are cast and wrought alloy, which exhibit fundamental microstructural differences in terms of grain size and hard phases. The impact of implant alloy microstructure on the occurring modes of corrosion and subsequent metal ion release is not well understood.

QUESTIONS/PURPOSES

The purpose of this study was to determine whether (1) the microstructure of cast CoCrMo alloy varies broadly between manufacturers and can dictate specific corrosion modes; and whether (2) the microstructure of wrought CoCrMo alloy is more consistent between manufacturers and has low implications on the alloy's corrosion behavior.

METHODS

The alloy microstructure of four femoral-stem and three femoral-head designs from four manufacturers was metallographically and electrochemically characterized. Three stem designs were made from cast alloy; all three head designs and one stem design were made from wrought alloy. Alloy samples were sectioned from retrieved components and then polished and etched to visualize grain structure and hard phases such as carbides (eg, M₂₃C₆) or intermetallic phases (eg, σ phase). Potentiodynamic polarization (PDP) tests were conducted to determine the corrosion potential (E_corr), corrosion current density (I_corr), and pitting potential (E_pit) for each alloy. Four devices were tested within each group, and each measurement was repeated three times to ensure repeatable results. Differences in PDP metrics between manufacturers and between alloys with different hard phase contents were compared using one-way analysis of variance and independent-sample t-tests. Microstructural features such as twin boundaries and slip bands as well as corrosion damage features were viewed and qualitatively assessed in a scanning electron microscope.

RESULTS

We found broad variability in implant alloy microstructure for both cast and wrought alloy between manufacturers, but also within the same implant design. In cast alloys, there was no difference in PDP metrics between manufacturers. However, coarse hard phases and clusters of hard phases (mainly intermetallic phases) were associated with severe phase boundary corrosion and pitting corrosion. Furthermore, cast alloys with hard phases had a lower E_pit than those without (0.46 V, SD 0.042; 0.53 V, SD 0.03, respectively; p = 0.015). Wrought alloys exhibited either no hard phases or numerous carbides (M₂₃C₆). However, the corrosion behavior was mainly affected by lattice defects and banded structures indicative of segregations that appear to be introduced during bar stock manufacturing. Alloys with banding had a lower E_corr (p = 0.008) and higher I_corr (p = 0.028) than alloys without banding (-0.76 V, SD 0.003; -0.73 V, SD 0.009; and 1.14 × 10^-4 mA/cm², SD 1.47 × 10^-5; 5.2 × 10^-5 mA/cm², SD 2.57 × 10^-5, respectively). Alloys with carbides had a slightly higher E_corr (p = 0.046) than those without (-0.755 V, SD 0.005; -0.761 V, SD 0.004); however, alloys with carbides exhibited more severe corrosion damage as a result of phase boundary corrosion, hard phase detachment, and subsequent local crevice corrosion.

CONCLUSIONS

The observed variability in CoCrMo alloy microstructure of both cast and wrought components in this study appears to be an important issue to address, perhaps through better standards, to minimize in vivo corrosion. The finding of the banded structures within wrought alloys is especially concerning because it unfavorably influences the corrosion behavior independent of the manufacturer. The findings suggest that a homogeneous alloy microstructure with a minimal hard phase fraction exhibits more favorable corrosion behavior within the in vivo environment of modular taper junctions, thus lowering metal ion release and subsequently the risk of ALTRs to corrosion products. Also, the question arises if hard phases fulfill a useful purpose in metal-on-polyethylene bearings, because they may come with a higher risk of phase boundary corrosion and pitting corrosion and the benefit they provide by adding strength is not needed (unlike in metal-on-metal bearings).

CLINICAL RELEVANCE

Implant failure resulting from corrosion processes within modular junctions is a major concern in THA. Our results suggest that implant alloy microstructure is not sufficiently standardized and may also dictate specific corrosion modes and subsequent metal ion release.

Same Same but Different? 12/14 Stem and Head Tapers in Total Hip Arthroplasty

BACKGROUND

Taper corrosion has been identified to be a major concern in total hip arthroplasty during the past years. So far, the mechanisms that lead to taper corrosion in modular taper junctions are not fully understood. However, it has been shown that corrosion is also influenced by the geometry and topography of the taper, and these parameters vary among the implant manufacturers. The purpose of this study was to investigate the variations of common stem and head tapers regarding design and surface characteristics.

METHODS

An analysis of selected commercially available 12/14 stem and head tapers was performed. As geometric parameters, the taper angle, the opening taper diameter, and the taper length were measured using a coordinate measuring machine. Several topographic parameters were determined using a tactile roughness measurement instrument.

RESULTS

Although all investigated tapers are so-called 12/14 tapers, this study showed that the stem and head tapers differ among the manufacturers. The stem tapers were clearly different in both geometry and topography, and the range in variation of the topographic parameter was greater than it was for the geometric parameter. In contrast, the head tapers were different in their geometry, although not in topography.

CONCLUSION

Ultimately, this study provides an overview on the characteristics and variations of modular hip taper connections, and in addition, a new classification system regarding the surface finish is presented. These findings could be further considered in experimental corrosion or retrieval studies.

[Endoprostheses in the elderly : Biomaterials, implant selection and fixation technique]

The replacement of hip and knee joints is one of the greatest success stories in orthopedics. Due to continuous improvement of biomaterials and implant design, patient-associated problems are now mostly multifactorial and only rarely caused by the implant. Abrasion was significantly reduced by the introduction of highly cross-linked polyethylene (PE), antioxidant stabilized PE, new ceramics and the development of ceramic and protective surfaces. It is assumed that further reduction of frictional resistance will not lead to a significantly better clinical result: however, the problem of periprosthetic infections and implant-related incompatibility is still unsolved and remains challenging for biomaterial research. For the knee joint PE will be irreplaceable for joint articulation even in the future due to the contact situation. Mobile bearings and fixed bearings are two established successful philosophies, which have shown comparably good clinical results. For the hip joint, it is forecasted that ceramic-on-ceramic will be the system of the future if the correct positioning and mounting of the components can be solved so that the problems, such as development of noise and breakage can be reduced to a minimum. An in-depth understanding and detailed knowledge of the biomaterials by the surgeon can prevent implant-related problems. For elderly patients it is assumed that the economic burden on the public healthcare system will have the strongest impact on implant selection.

Mechanical, chemical and biological damage modes within head-neck tapers of CoCrMo and Ti6Al4V contemporary hip replacements

Total hip replacement (THR) failure due to mechanically assisted crevice corrosion within modular head-neck taper junctions remains a major concern. Several processes leading to the generation of detrimental corrosion products have been reported in first generation modular devices. Contemporary junctions differ in their geometries, surface finishes, and head alloy. This study specifically provides an overview for CoCrMo/CoCrMo and CoCrMo/Ti6Al4V head-neck contemporary junctions. A retrieval study of 364 retrieved THRs was conducted which included visual examination and determination of damage scores, as well as the examination of damage features using scanning electron microscopy. Different separately occurring or overlapping damage modes were identified that appeared to be either mechanically or chemically dominated. Mechanically dominated damage features included plastic deformation, fretting, and material transfer, whereas chemically dominate damage included pitting corrosion, etching, intergranular corrosion, phase boundary corrosion, and column damage. Etching associated cellular activity was also observed. Furthermore, fretting corrosion, formation of thick oxide films, and imprinting were observed which appeared to be the result of both mechanical and chemical processes. The occurrence and extent of damage caused by different modes was shown to depend on the material, the material couple, and alloy microstructure. In order to minimize THR failure due to material degradation within modular junctions, it is important to distinguish different damage modes, determine their cause, and identify appropriate counter measures, which may differ depending on the material, specific microstructural alloy features, and design factors such as surface topography. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 106B: 1672-1685, 2018.