Biological applications of copper-containing materials

Study on the Synergistic Effects of Cu and Sr on Biodegradable Zn Alloys

Bone defect repair and postoperative infections are among the most challenging issues faced by orthopedic surgeons. Thus, the antibacterial agent Cu and the osteogenic promoter Sr have been widely incorporated into biodegradable alloys separately. However, to the best of our knowledge, the synergistic effects of Cu and Sr on zinc alloys have not been investigated. Therefore, we have developed a series of novel Zn-4Cu-xSr (x = 0.05, 0.1, and 0.3 wt %) alloys. Our results showed that the addition of Cu and Sr significantly increased the strength of pure zinc while maintaining a certain level of ductility. Plastic deformation further enhanced the strength and ductility of the alloys. The tensile strength of HR Zn-4Cu-xSr alloys remains between 233.34 ± 1.31 MPa and 235.81 ± 3.0 MPa, with elongation values ranging from 45.7 ± 1.56% to 49.6 ± 6.22%. The HE Zn-4Cu-0.05Sr alloy exhibits a high elongation of 95.05 ± 11.1%. Furthermore, the HE Zn-4Cu-0.1Sr alloy demonstrates the best overall mechanical performance with ultimate tensile strength (σuts), yield strength (σys), and elongation (ε) values of 252.73 ± 0.12 MPa, 181.0 ± 0.79 MPa, and 42.8 ± 1.13%, respectively. The corrosion rate of HE Zn-4Cu-xSr alloys increases with an increase in Sr content. All samples exhibit satisfactory cytocompatibility with the cells displaying a healthy spindle-like morphology. In vitro antibacterial tests show that the HE Zn-4Cu-xSr alloys exhibit significant antibacterial effects against Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli), with the antibacterial properties strengthening as the Sr content increases. Therefore, this study demonstrates the tremendous potential application of Zn-4Cu-xSr alloys in biodegradable zinc alloys for bone fracture fixation and repair.

Copper ions-photo dual-crosslinked alginate hydrogel for angiogenesis and osteogenesis

Early healing of bone defects is still a clinical challenge. Many bone-filling materials have been studied, among which photocrosslinked alginate has received significant attention due to its good biocompatibility and morphological plasticity. Although it has been confirmed that photocrosslinked alginate can be used as an extracellular matrix for 3D cell culture, it lacks osteogenesis-related biological functions. This study constructed a copper ions-photo dual-crosslinked alginate hydrogel scaffold by controlling the copper ion concentration. The scaffolds were shaped by photocrosslinking and then endowed with biological functions by copper ions crosslinking. According to in vitro research, the dual-crosslinked hydrogel increased the compressive strength and favored copper dose-dependent osteoblast differentiation and cell surface adherence of rat bone marrow mesenchymal stem cells and the expression of type I collagen (Col1), runt-related transcription factor 2 (Runx2), osteocalcin (OCN), vascular endothelial growth factor (VEGF). In addition, hydrogel scaffolds were implanted into rat skull defects, and more angiogenesis and osteogenesis could be observed in in vivo studies. The above results show that the copper-photo-crosslinked hydrogel scaffold has excellent osseointegration properties and can potentially promote angiogenesis and early healing of bone defects, providing a reference solution for bone tissue engineering materials.

Health Risk Assessment of Toxic Metal(loids) Consumed Through Plant-Based Anti-diabetic Therapeutics Collected in the Northern Divisional City of Rajshahi, Bangladesh

The present study investigates human health risks upon consumption of herbal medicines in terms of ten toxic metalloids in 20 plant-based anti-diabetic therapeutics. The analysis of metalloids was determined by an atomic absorption spectrometer after microwave-assisted digestion. The computation of hazard quotients (HQ) and hazard indexes (HI) of metalloids leads to the assessment of non-carcinogenic health risks. Carcinogenic risk was assessed based on cancer slope factor (CSF) and chronic daily intake (CDI) values. Comparison with WHO regulatory cut-off points for each metalloid: seven samples for Mn, 12 samples for Hg, three samples for Cu, eight samples for Ni, four samples for Cd, two samples for Pb, one sample for Cr, and eight samples for Zn are unsafe to consume. Non-carcinogenic human health risk is predicted for Mn in seven samples, Fe in one sample, Hg in ten samples, Cu in three samples, Ni in one sample, and Pb in two samples. HI values greater than 1 predict non-carcinogenic health risk in thirteen samples. Incremental lifetime cancer risk (ILCR) remains for As (inorganic) in 12 samples, Cr (+ 6) in one sample, and Pb in no samples. To guarantee consumer safety, the implementation of strict monitoring is suggested.

The impact of copper on bone metabolism

Copper is an essential trace element for the human body. Abnormalities in copper metabolism can lead to bone defects, mainly by directly affecting the viability of osteoblasts and osteoclasts and their bone remodeling function, or indirectly regulating bone metabolism by influencing enzyme activities as cofactors. Copper ions released from biological materials can affect osteoblasts and osteoclasts, either directly or indirectly by modulating the inflammatory response, oxidative stress, and rapamycin signaling. This review presents an overview of recent progress in the impact of copper on bone metabolism. Translational potential of this article: The impact of copper on bone metabolism can provide insights into clinical application of copper-containing supplements and biomaterials.

Regulation of metabolic microenvironment with a nanocomposite hydrogel for improved bone fracture healing

Bone nonunion poses an urgent clinical challenge that needs to be addressed. Recent studies have revealed that the metabolic microenvironment plays a vital role in fracture healing. Macrophages and bone marrow-derived mesenchymal stromal cells (BMSCs) are important targets for therapeutic interventions in bone fractures. Itaconate is a TCA cycle metabolite that has emerged as a potent macrophage immunomodulator that limits the inflammatory response. During osteogenic differentiation, BMSCs tend to undergo aerobic glycolysis and metabolize glucose to lactate. Copper ion (Cu2+) is an essential trace element that participates in glucose metabolism and may stimulate glycolysis in BMSCs and promote osteogenesis. In this study, we develop a 4-octyl itaconate (4-OI)@Cu@Gel nanocomposite hydrogel that can effectively deliver and release 4-OI and Cu2+ to modulate the metabolic microenvironment and improve the functions of cells involved in the fracture healing process. The findings reveal that burst release of 4-OI reduces the inflammatory response, promotes M2 macrophage polarization, and alleviates oxidative stress, while sustained release of Cu2+ stimulates BMSC glycolysis and osteogenic differentiation and enhances endothelial cell angiogenesis. Consequently, the 4-OI@Cu@Gel system achieves rapid fracture healing in mice. Thus, this study proposes a promising regenerative strategy to expedite bone fracture healing through metabolic reprogramming of macrophages and BMSCs.

Chelate Complexes of 3d Transition Metal Ions─A Challenge for Electronic-Structure Methods?

Different electronic-structure methods were assessed for their ability to predict two important properties of the industrially relevant chelating agent nitrilotriacetic acid (NTA): its selectivity with respect to six different first-row transition metal ions and the spin-state energetics of its complex with Fe(III). The investigated methods encompassed density functional theory (DFT), the random phase approximation (RPA), coupled cluster (CC) theory, and the auxiliary-field quantum Monte Carlo (AFQMC) method, as well as the complete active space self-consistent field (CASSCF) method and the respective on-top methods: second-order N-electron valence state perturbation theory (NEVPT2) and multiconfiguration pair-density functional theory (MC-PDFT). Different strategies for selecting active spaces were explored, and the density matrix renormalization group (DMRG) approach was used to solve the largest active spaces. Despite somewhat ambiguous multi-reference diagnostics, most methods gave relatively good agreement with experimental data for the chemical reactions connected to the selectivity, which only involved transition-metal complexes in their high-spin state. CC methods yielded the highest accuracy followed by range-separated DFT and AFQMC. We discussed in detail that even higher accuracies can be obtained with NEVPT2, under the prerequisite that consistent active spaces along the entire chemical reaction can be selected, which was not the case for reactions involving Fe(III). A bigger challenge for electronic-structure methods was the prediction of the spin-state energetics, which additionally involved lower spin states that exhibited larger multi-reference diagnostics. Conceptually different, typically accurate methods ranging from CC theory via DMRG-NEVPT2 in combination with large active spaces to AFQMC agreed well that the high-spin state is energetically significantly favored over the other spin states. This was in contrast to most DFT functionals and RPA which yielded a smaller stabilization and some common DFT functionals and MC-PDFT even predicting the low-spin state to be energetically most favorable.

Phenolic Ligand-Metal Charge Transfer Induced Copper Nanozyme with Reactive Oxygen Species-Scavenging Ability for Chronic Wound Healing

Chronic wounds frequently arise as a complication in diabetic patients, and their management remains a significant clinical hurdle due to their nonhealing nature featured by heightened oxidative stress and impaired healing cells at the wound site. Herein, we present a 2D copper antioxidant nanozyme induced by phenolic ligand-metal charge transfer (LMCT) to eliminate reactive oxygen species (ROS) and facilitate the healing of chronic diabetic wounds. We found that polyphenol ligands coordinated on the Cu3(PO4)2 nanosheets led to a strong charge transfer at the interface and regulated the valence states of Cu. The obtained Cu nanozyme exhibited efficient scavenging ability toward different oxidative species and protected human cells from oxidative damage. The nanozyme enhanced the healing of diabetic wounds by promoting re-epithelialization, collagen deposition, angiogenesis, and immunoregulation. This work demonstrates the LMCT-induced ROS scavenging ability on a nanointerface, providing an alternative strategy of constructing metal-based nanozymes for the treatment of diabetic wounds as well as other diseases.

Cu-vitamin B3 donut-like MOFs incorporated into TEMPO-oxidized bacterial cellulose nanofibers for wound healing

In this study, a novel multifunctional nanocomposite wound dressing was developed, consisting of TEMPO-oxidized bacterial cellulose (TOBC) nanofibers functionalized with donut-like copper-based metal-organic frameworks (CuVB3 MOFs). These CuVB3 MOFs were constructed using copper nodes linked by vitamin B3 molecules, resulting in a copper nicotinate crystal structure as confirmed by X-ray diffraction. Electron microscopy confirmed the presence of donut-like microstructures with uniform element distribution in the synthesized MOFs. Through the incorporation of CuVB3 MOFs into the TOBC nanofibers, innovative TOBC-CuVB3 nanocomposites were created. Biocompatibility testing using the MTT assay demonstrated enhanced cell viability of over 115% for the TOBC-CuVB3 nanocomposite. Acridine Orange staining revealed a ratio of 88-92% live cells on the wound dressings. Furthermore, fibroblast cells cultured on TOBC-CuVB3 exhibited expanded morphologies with long filopodia. The agar diffusion method exhibited improved antibacterial activity against both Gram-positive and Gram-negative bacterial strains, correlating with increased CuVB3 concentration in the samples. In vitro cellular scratch assays demonstrated excellent wound healing potential, with a closure rate of over 98% for wounds treated with the TOBC-CuVB3 nanocomposite. These findings underscore the synergistic effects of copper, vitamin B3, and TOBC nanofibers in the wound healing process.

Manganese-Implanted Titanium Modulates the Crosstalk between Bone Marrow Mesenchymal Stem Cells and Macrophages to Improve Osteogenesis

Manganese (Mn) is an essential micronutrient in various physiological processes, but its functions in bone metabolism remain undefined. This is partly due to the interplay between immune and bone cells because Mn plays a central role in the immune system. In this study, we utilized the plasma immersion ion implantation and deposition (PIII&D) technique to introduce Mn onto the titanium surface. The results demonstrated that Mn-implanted surfaces stimulated the shift of macrophages toward the M1 phenotype and had minimal effects on the osteogenic differentiation of mouse bone marrow mesenchymal stem cells (mBMSCs) under mono-culture conditions. However, they promoted the M2 polarization of macrophages and improved the osteogenic activities of mBMSCs under co-culture conditions, indicating the importance of the crosstalk between mBMSCs and macrophages mediated by Mn in osteogenic activities. This study provides a positive incentive for the application of Mn in the field of osteoimmunology.

Antibacterial performance of a porous Cu-bearing titanium alloy by laser additive manufacturing

Porphyromonas gingivalis (P. gingivalis) is the most common species that causes peri-implantitis. It forms an irreversible dense biofilm and causes inflammation. A novel 3D-printed porous TC4-6Cu alloy was fabricated using selective laser melting (SLM) technology for the dental implant, which is anticipated to inhibit biofilm formation. We attempted to investigate the antibacterial ability and antibacterial mechanism of the 3D-printed porous TC4-6Cu alloy against P. gingivalis. This work used scanning electron microscopy (SEM) and laser confocal microscopy (CLSM) to detect the antimicrobial ability of the alloy against sessile P. gingivalis. The results indicated that the 3D-printed porous TC4-6Cu alloy could cause bacterial fragmentation and deformation. Plate antimicrobial counting experiments showed that the antibacterial rates of the alloy against adherent bacteria and planktonic bacteria after 24 h were 98.05% and 73.92%, respectively. The minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) of Cu2+ were tested to appraise the antibacterial property of the alloy against planktonic P. gingivalis. The relationship between the antibacterial mechanism of the alloy with oxidative stress was evaluated through ROS fluorescence intensity and protein leakage concentration. The results revealed that the alloy significantly eliminated adherent bacteria and inhibited biofilm formation. Moreover, 3D-printed porous TC4-6Cu alloy demonstrated significant bactericidal ability by inducing the production of reactive oxygen species (ROS), which could result in protein leakage from the bacterial cell membrane. This research may open a new perspective on the development and biomedical applications for dental implantation.

Morphological, mechanical and antibacterial properties of Ti-Cu-N thin films deposited by sputtering DC

The problems associated with Stainless Steel 316 L (SS 316 L) orthopedic implants, when implanted in the human body, are infection, local inflammation, and the possibility of bacterial growth. In this study, SS 316 L was coated with copper-doped Titanium Nitride (Ti-Cu-N) using the DC Sputtering technique. This Ti-Cu-N film improved the antibacterial performance and mechanical properties of SS 316 L. The Ti-Cu-N films were deposited using reactive DC sputtering with an 80%:20% argon to nitrogen ratio. The source voltage and current were kept constant at 10 kV and 10 mA, respectively. X-Ray Diffraction (XRD) showed that the phases formed were TiN and Cu with FCC crystal structure. Results show that the surfaces of samples containing 44.34 wt% and 54.97 wt% Cu had antibacterial effectiveness against Staphylococcus aureus (S. Aureus). The highest hardness value of a Ti-Cu-N layer was 212.032 Vickers Hardness Number (VHN), which was an improvement of 36.63% on the raw material (155.18 VHN). Surface morphology analysis using SEM-EDS was performed on the samples before and after the antibacterial test to investigate the antibacterial mechanism of the surfaces of SS 316 L containing Ti-Cu-N against S. Aureus.

Exploring the Multitarget Activity of Wedelolactone against Alzheimer's Disease: Insights from In Silico Study

In this study, Wedelolactone's multitarget activity against Alzheimer's disease was examined using density functional theory and molecular docking techniques. At physiological pH, the pK _a and molar fractions have been estimated. The most likely relative rate constants of two radical scavenger mechanisms are formal hydrogen transfer in a lipid environment and single-electron transfer in a water solvent. Compared to Trolox (k _overall = 8.96 × 10⁴ M^-1 s^-1), Wedelolactone (k _overall = 4.26 × 10⁹ M^-1 s^-1) is more efficient in scavenging the HOO^• radical in an aqueous environment. The chelation capacity of metals was investigated by examining the complexation of the Cu(II) ion at various coordination positions and calculating the complexation kinetic constants. Furthermore, molecular docking simulations showed that the known forms of Wedelolactone at physiological pH effectively inhibited the AChE and BChE enzymes by comparing their activity to that of tacrine (control). Wedelolactone is a promising drug candidate for Alzheimer's disease therapy in light of these findings.

Copper modified cobalt-chromium particles for attenuating wear particle induced-inflammation and osteoclastogenesis

The nature of aseptic prosthetic loosening mainly relates to the wear particles that induce inflammation and subsequent osteoclastogenesis. The ideal approach to impede wear particle-induced osteolysis should minimize inflammation and osteoclastogenesis. In this work, Co29Cr9W3Cu particles were used as a research model for the first time to explore the response of Co29Cr9W3Cu particles to inflammatory response and osteoclast activation in vitro and in vivo by using Co29Cr9W particles as the control group. In vitro studies showed that the Co29Cr9W3Cu particles could promote the generation of M2-phenotype macrophages and increase the expression level of anti-inflammatory factor IL-10, while inhibiting the formation of M1-phenotype macrophages and down-regulating the expression of inflammatory factors TNF-α, IL-6 and IL-1β; More importantly, the Co29Cr9W3Cu particles reduced the expression of NF-κB and downstream osteoclast related-specific transcription marker genes, such as TRAP, NFATc1, and Cath-K; In vivo results indicated that the Co29Cr9W3Cu particles exposed to murine calvarial contributed to decreasing the amount of osteoclast and osteolysis area. These findings collectively demonstrated that Cu-bearing cobalt-chromium alloy may potentially delay the development of aseptic prosthetic loosening induced by wear particles, which is expected to provide evidence of Co29Cr9W3Cu alloy as an alternative material of joint implants with anti-wear associated osteolysis.

Cellular Uptake of Modified Mesoporous Bioactive Glass Nanoparticles for Effective Intracellular Delivery of Therapeutic Agents

Introduction

There has recently been a surge of interest in mesoporous bioactive glass nanoparticles (MBGNs) as multi-functional nanocarriers for application in bone-reconstructive and -regenerative surgery. Their excellent control over their structural and physicochemical properties renders these nanoparticles suitable for the intracellular delivery of therapeutic agents to combat degenerative bone diseases, such as bone infection, or bone cancer. Generally, the therapeutic efficacy of nanocarriers strongly depends on the efficacy of their cellular uptake, which is determined by numerous factors including cellular features and the physicochemical characteristics of nanocarriers, particularly surface charge. In this study, we have systematically investigated the effect of the surface charge of MBGNs doped with copper as a model therapeutic agent on cellular uptake by both macrophages and pre-osteoblast cells involved in bone healing and bone infections to guide the future design of MBGN-based nanocarriers.

Methods

Cu-MBGNs with negative, neutral, and positive surface charges were synthesized and their cellular uptake efficiency was assessed. Additionally, the intracellular fate of internalized nanoparticles along with their ability to deliver therapeutic cargo was studied in detail.

Results

The results showed that both cell types internalized Cu-MBGNs regardless of their surface charge, indicating that cellular uptake of nanoparticles is a complex process influenced by multiple factors. This similarity in cellular uptake was attributed to the formation of a protein corona surrounding the nanoparticles when exposed to protein-rich biological media, which masks the original nanoparticle surface. Once internalized, the nanoparticles were found to mainly colocalize with lysosomes, exposing them to a more compartmentalized and acidic environment. Furthermore, we verified that Cu-MBGNs released their ionic components (Si, Ca, and Cu ions) in both acidic and neutral environments, leading to the delivery of these therapeutic cargos intracellularly.

Conclusion

The effective internalization of Cu-MBGNs and their ability to deliver cargos intracellularly highlight their potential as intracellular delivery nanocarriers for bone-regenerative and -healing applications.

H2O2/NIR-sensitive "two-step" nano theranostic system based hollow mesoporous copper sulfide/hyaluronic acid/JWH133 as an optimally designed delivery system for multidimensional treatment of RA

Cannabinoid receptors are widely distributed in many cells in Rheumatoid arthritis RA and strengthening factor to boost the development of RA diseases. Here, the hollow mesoporous copper sulfide (CuS) was used as the carrier skeleton and the cannabinoid type 2 (CB2) receptor agonist JWH133 was efficiently loaded inside of CuS through adsorption, then the outer layer was modified with hyaluronic acid (HA) to prevent the leakage of internal drugs. After the CuS-JWH133@HA nano carrier reached the target area, HA responsive cracked under RA microenvironment to realize the first step of accurate drug delivery of JWH133, and the thermally responsive CuS under near-infrared (NIR) promoted the release of internal drugs. Then, JWH133 specifically combined CB2 receptors on the surface of macrophage, synovial cells and osteoblasts to realize the second step of drug delivery. The inflammatory factors secreted by cells are significantly inhibited, and the activity of osteoblasts was significantly enhanced. Therapeutic effect by CuS-JWH133@HA of RA was well verified by decreasing levels of inflammation in vivo and improvement of inflamed and swollen joints of mice. The CuS-JWH133@HA nanocomposite showed satisfactory multidimensional therapeutic effect of RA in vitro and in vivo, which provided a novel idea for RA treatment.

Evaluation of Trace Element and Heavy Metal Levels of Some Ethnobotanically Important Medicinal Plants Used as Remedies in Southern Turkey in Terms of Human Health Risk

Heavy metal accumulation in medicinal plants has increased dramatically in recent years due to agricultural and industrial activities leading to pollution of natural sources. This study is focused on the concentration of trace elements and heavy metals in aboveground parts of 33 medicinal plants from the Eastern Mediterranean of Turkey. Results showed that the Al concentrations varied between 4.368 and 1104.627, the B level varied between 47.850 and 271.479, Ca values ranged between 1971.213 and 22,642.895, Cd concentrations ranged between 0.011 and 0.651, Cr contents varied between 1.371 and 41.692, Cu values varied between 13.278 and 42.586, Fe concentrations varied between 20.705 and 1276.783, K levels ranged between 652.143 and 14,440.946, Mg concentrations varied from 336.871 to 1869.486, Mn contents varied between 46.383 and 849.492, Na concentrations varied between 167.144 and 3401.252, Ni values varied between 0.065 and 9.968, Pb levels ranged between 1.311 and 16.238, and Zn concentrations ranged between 67.250 and 281.954 mg kg-1, respectively. Furthermore, Recommended Dietary Allowance (RDA) values for trace elements and estimated daily intake (EDI), target hazard quotient (THQ), and hazard index (HI) for heavy metals were calculated. The concentrations of heavy metals in some studied plants distributed in industrial and mining regions were found as slightly higher than the acceptable limits determined by WHO. Consequently, in order to prevent this heavy metal accumulation, when collecting medicinal aromatic plants, rural areas, close to clean rivers, or mountainous areas should be preferred, away from highway, mining, and industrial areas.

Copper regulation of immune response and potential implications for treating orthopedic disorders

Copper is an indispensable trace metal element in human body, and copper deficiency is rare in clinic. However, diseases associated with serum copper deficiency, such as leukopenia, neutropenia, arthritis, osteoporosis, and bone defects, are well known. Copper ions can also achieve the effect of fighting pathogenic bacteria through the "contact killing" characteristic. Copper ion is also an important cofactor of bone matrix synthase, plays an important role in the pathophysiology of orthopedic diseases. The present review highlights the biological functions of copper in immunity, bone diseases and stem cells, as well as potential drug development targeting copper status for diagnostics and therapeutics of copper-associated bone diseases.

Facile post modification synthesis of copper-doped mesoporous bioactive glass with high antibacterial performance to fight bone infection

Successful treatment of infected bone defects caused by multi-drug resistant bacteria (MDR) has become a major clinical challenge, stressing the urgent need for effective antibacterial bone graft substitutes. Mesoporous bioactive glass nanoparticles (MBGNs), a rapidly emerging class of nanoscale biomaterials, offer specific advantages for the development of biomaterials to treat bone infection due to endowed antibacterial features. Herein, we propose a facile post-modification sol-gel strategy to synthesize effective antibacterial MBGNs doped with copper ions (Cu-PMMBGNs). In this strategy, amine functional groups as chelating agents were introduced to premade mesoporous silica nanoparticles (MSNs) which further facilitate the incorporation of high content of calcium (∼17 mol%) and copper ions (∼8 mol%) without compromising nanoparticle shape, mesoporosity, and homogeneity. The resulting nanoparticles were degradable and showed rapidly induce abundant deposition of apatite crystals on their surface upon soaking in simulated body fluids (SBF) after 3 days. Cu-PMMBGNs exhibited a dose-dependent inhibitory effect on Methicillin-resistant Staphylococcus aureus (MRSA) bacteria, which are common pathogens causing severe bone infections. Most importantly, the nanoparticles containing 5 mol% copper ions at concentrations of 500 and 1000 μg.mL^-1 showed highly effective antibacterial performance as reflected by a 99.9 % reduction of bacterial viability. Nanoparticles at a concentration of 500 μg.mL^-1 showed no significant cytotoxicity toward preosteoblast cells (∼85-89 % cell viability) compared to the control group. In addition, the nanoscale properties of synthesized Cu-PMMBGNs (∼100 nm in size) facilitated their internalization into preosteoblast cells, which highlights their potential as intracellular carriers in combating intracellular bacteria. Therefore, these copper-doped nanoparticles hold strong promise for use as an antibacterial component in antibacterial bone substitutes such as hydrogels, nanocomposites, and coatings.

Photo-Stimuli-Responsive CuS Nanomaterials as Cutting-Edge Platform Materials for Antibacterial Applications

Photo-stimuli-responsive therapeutic nanomaterials have gained widespread attention as frontline materials for biomedical applications. The photoactivation strategies are classified as single-modality (based on either reactive oxygen species (ROS)-based photodynamic therapy (PDT), hyperthermia-based photothermal therapy (PTT)), or dual-modality (which combines PDT and PTT). Due to its minimal invasiveness, phototherapy has been extensively applied as an efficient therapeutic platform for many diseases, including skin cancers. However, extensive implementation of phototherapy to address the emergence of multidrug-resistant (MDR) bacterial infections remains challenging. This review focuses on copper sulfide (CuS) nanomaterials as efficient and cost-effective PDT and PTT therapeutic nanomaterials with antibacterial activity. The features and merits of CuS nanomaterials as therapeutics are compared to those of other nanomaterials. Control of the dimensions and morphological complexity of CuS nanomaterials through judicious synthesis is then introduced. Both the in vitro antibacterial activity and the in vivo therapeutic effect of CuS nanomaterials and derivative nanocomposites composed of 2D nanomaterials, polymers, metals, metal oxides, and proteins are described in detail. Finally, the perspective of photo-stimuli-responsive CuS nanomaterials for future clinical antibacterial applications is highlighted. This review illustrates that CuS nanomaterials are highly effective, low-toxic, and environmentally friendly antibacterial agents or platform nanomaterials for combatting MDR bacterial infections.

Differentiating Wild and Apiary Honey by Elemental Profiling: a Case Study from Mangroves of Indian Sundarban

Honey is a natural substance produced by honeybees from the nectar or secretion of flowering plants. Along with the botanical and geographical origin, several environmental factors also play a major role in determining the characteristics of honey. The aim of this study is to determine and compare the elemental concentration of various macro and trace elements in apiary and wild honeys collected from different parts of Indian Sundarbans. The elemental analysis was performed in inductively coupled plasma optical emission spectroscopy preceded by microwave digestion method. The concentrations of 19 elements (Ag, Al, As, B, Ca, Cd, Co, Cr, Cu, Fe, K, Li, Mg, Mn, Na, Ni, Pb, Se and Zn) were investigated from thirteen locations of Indian Sundarbans. This comparative study shows in wild honey samples, the concentration of K was highest followed by Ca, Mg and Na and Zn was lowest among all. In contrast, in apiary honey samples, Ca had maximum concentration followed by K, Mg and Na and Ag had minimum among all. The elemental concentration in honey from apiary was either equal or higher than their wild counterpart. The results of the factor analysis of PCA algorithm for wild and apiary honey samples were highly variable which implies that the elements are not coming from the same origin. The concentration of element was found to be highly variable across sites and across sources of honey samples.

Effect of Copper Addition on the Formability of 304L Austenitic Stainless Steel

To improve the antibacterial properties of 304L austenitic stainless steel, copper is often added as an antibacterial agent, but the forming performance of the resulting material is poor, impacting its actual production and use. Therefore, this study investigated the influence of copper addition on the formability of 304L austenitic stainless steel with drawing, cupping and conical cup forming tests. Mechanical properties were determined with tensile and hardness tests. The microstructure and phase transformation were further characterized by metallographic microscopy, scanning electron microscopy and x-ray diffraction analysis. It was found that the addition of copper impaired the mechanical properties of 304L austenitic stainless steel, increased the stacking fault energy of the material and inhibited the occurrence of strain-induced martensite transformation, leading to a decrease in the formability of 304L austenitic stainless steel.

Metal-Based Nanoparticles: Antibacterial Mechanisms and Biomedical Application

The growing increase in antibiotic-resistant bacteria has led to the search for new antibacterial agents capable of overcoming the resistance problem. In recent years, nanoparticles (NPs) have been increasingly used to target bacteria as an alternative to antibiotics. The most promising nanomaterials for biomedical applications are metal and metal oxide NPs, due to their intrinsic antibacterial activity. Although NPs show interesting antibacterial properties, the mechanisms underlying their action are still poorly understood, limiting their use in clinical applications. In this review, an overview of the mechanisms underlying the antibacterial activity of metal and metal oxide NPs will be provided, relating their efficacy to: (i) bacterial strain; (ii) higher microbial organizations (biofilm); (iii) and physico-chemical properties of NPs. In addition, bacterial resistance strategies will be also discussed to better evaluate the feasibility of the different treatments adopted in the clinical safety fields. Finally, a wide analysis on recent biomedical applications of metal and metal oxide NPs with antibacterial activity will be provided.

Tailoring Cu2+-loaded electrospun membranes with antibacterial ability for guided bone regeneration

Copper (Cu)-loaded electrospun membranes were tailored for guided bone regeneration (GBR), targeting the stimulation of innate cells active in bone growth and the prevention of bacterial infections. Functional GBR membranes were produced via an electrospinning set-up using a silk-based solution associated with polyethylene oxide (Silk/PEO - control). Experimental groups were loaded with copper oxide using varying weight percentages (0.05 % to 1 % of CuO). The morphological, structural, chemical, and mechanical properties of membranes were evaluated. Direct and indirect in vitro cytocompatibility experiments were performed with primary human bone mesenchymal stem cells and primary human umbilical vein endothelial cells. The antibacterial potential of membranes was tested with Staphylococcus aureus and Fusobacterium nucleatum biofilm. CuO was successfully incorporated into membranes as clusters without compromising their mechanical properties for clinical applicability. Increased Cu concentrations generated membranes with thinner nanofibers, greater pore areas, and stronger antimicrobial effect (p < 0.01). Cu²⁺ ion was released from the nanofiber membranes during 1 week, showing higher release in acidic conditions. CuO 0.1 % and CuO 0.05 % membranes were able to support and stimulate cell adhesion and proliferation (p < 0.05), and favor angiogenic responses of vascular cells. In addition, detailed quantitative and qualitative analysis determined that amount of the attached biofilm was reduced on the tailored functional Cu²⁺-loaded GBR membrane. Importantly, these qualities represent a valuable strategy to improve the bone regeneration process and diminish the risk of bacterial infections.

Biocompatibility Study of a Cu-Al-Ni Rod Obtained by Continuous Casting

Cu-Al-Nishape memory alloys (SMAs) are widely known for their better properties in comparison to other SMAs (lower production costs, increased ductility, enhanced machinability, reduced liquidus temperature, and decreased hysteresis), but there is still controversy in terms of the biological properties of these materials. The aim of this study was to evaluate biofunctional performances of Cu-Al-Ni alloy produced by continuous casting. The micro-chemical analysis was investigated by SEM/EDX. Immersion tests performed for seven days were used to estimate the quantity of Cu, Al, and Ni ions released in neutral pH and slightly acidic artificial saliva. To assess the biocompatibility of the Cu-Al-Ni alloy samples, MTT assay on fibroblasts and dental pulp cells was performed in indirect and direct contact with samples after 1,3, and 7 days.The study revealed that continuous casting enables the primary fabrication of Cu-Al-Ni rods with a shape memory effect. Samples immersed in artificial saliva with 6.5 pH value showed no significant amounts of released ions, despite the high concentration of copper in the alloy. However, in the acidic environment, the suppression of Cu was 0.14 µg/cm2, Al 1.9 µg/cm2, and Ni 0.73 µg/cm2, and as expected, it was confirmed that Cu-Al-Ni alloy is not corrosion resistant in an acidic environment. In conclusion, this study showed that biocompatibility concerns are related only to materials with a high Cu content in acidic environments. Oppositely, small doses of Cu ions promote cell proliferation, which might be useful in further attempts to enrich different biomedical materials with copper.

Enhanced anti-microbial activity and osseointegration of Ta/Cu co-implanted polyetheretherketone

Polyetheretherketone (PEEK) has been widely applied for orthopedic and oral implants due to its excellent mechanical properties, biocompatibility, and radiolucency. However, its bioinert and the lack of anti-microbial activity limit its application. We modified the PEEK surface with Ta/Cu co-implantation using plasma immersion ion-implantation technology. After implantation of Ta/Cu ions, the morphology and roughness of the PEEK surface were not significantly changed at micron level. We estimated the cytocompatibility, anti-microbial ability, and osteogenic differentiation of rat bone mesenchymal stem cells (BMSCs) of the modified surfaces in vitro. Compared to the untreated surfaces, the Ta ion-treated surface showed improved adhesion, proliferation, ALP activity, ECM mineralization, and osteogenic gene expression of BMSCs. Further, the Cu ion-treated surface showed reduced initial adhesion and proliferation of Escherichia coli and Staphylococcus aureus in vitro and proliferation of Staphylococcus aureus in the mouse subcutaneous implant-associated infection model. According to a rat bone repair model, all Ta ion-implanted groups demonstrated improved new bone formation. In summary, Ta/Cu ion co-impanation improved anti-microbial activity and promoted osseointegration of the PEEK surface.

In vitro and in vivo studies on bacteria and encrustation resistance of heparin/poly-L-lysine-Cu nanoparticles coating mediated by PDA for ureteral stent application

Ureteral stents are commonly utilized as a medical device to aid the flow of urine. However, biofilm formation and encrustation complications have been clinical problems. To overcome this challenge, heparin/poly-L-lysine-copper (Hep/PLL-Cu) nanoparticle was immobilized on a dopamine-coated polyurethane surface (PU/NPs). The stability and structural properties of the nanoparticles were characterized by Zeta potential, poly dispersion index, transmission electron microscopy, atom force microscopy and contact angle. The surface composition, antibacterial potency, encrustation resistance rate and biocompatibility of PU/NPs were investigated by scanning electron microscope, X-ray photoelectron spectroscopy, antibacterial assay and MTS assay, respectively. In addition, the anti-encrustation property was studied by implanting coated NPs stents in the rat bladder for 7 days. It was shown that the size and distribution of Hep/PLL-Cu nanoparticles were uniform. PU/NPs could inhibit Proteus mirabilis proliferation and biofilm formation, and exhibit no cytotoxicity. Less encrustation (Ca and Mg salt) was deposited both in vitro and in vivo on samples, demonstrating that the NPs coating could be a potential surface modification method of ureteral material for clinical use.

Copper-based metal-organic frameworks for biomedical applications

Metal-organic frameworks (MOFs) are a class of important porous, crystalline materials composed of metal ions (clusters) and organic ligands. Owing to the unique redox chemistry, photochemical and electrical property, and catalytic activity of Cu^2+/+, copper-based MOFs (Cu-MOFs) have been recently and extensively explored in various biomedical fields. In this review, we first make a brief introduction to the synthesis of Cu-MOFs and their composites, and highlight the recent synthetic strategies of two most studied representatives, three-dimensional HKUST-1 and two-dimensional Cu-TCPP. The recent advances of Cu-MOFs in the applications of cancer treatment, bacterial inhibition, biosensing, biocatalysis, and wound healing are summarized and discussed. Furthermore, we propose a prospect of the future development of Cu-MOFs in biomedical fields and beyond.

Cellulose-Conjugated Copper-Oxide Nanoparticles for the Treatment of Ethanol-Induced Gastric Ulcers in Wistar Rats

Gastric ulcer (GU) is the most common and chronic inflammatory condition mediated by multiple immune cells like neutrophils, macrophages, and lymphocytes with multiple pro-inflammatory cytokine interleukins such as IL-8, IL-10, IL-β, and interferon-γ (IFN-γ). Copper (Cu) is one of the essential micronutrients mainly found in the liver and brain. It plays a major role in metabolism, enzyme conversion, free radical scavenging, trafficking agents, and many others. Due to its various roles in the biological system, it can also be used as a therapeutic agent in many diseases like colon cancer, bone fracture healing, angiogenesis, as an antibacterial, wound-healing and radiotherapeutic agents. In this study, we used thiol-functionalized cellulose-conjugated copper-oxide nanoparticles (Cu^I/IIO NPs) synthesized under environmentally friendly conditions. We have evaluated the effects of cellulose-conjugated Cu^I/IIO NPs against ethanol-induced gastric ulcer in Wistar rats. The cellulose-conjugated Cu^I/IIO NPs were evaluated against different physical, histochemical, and inflammatory parameters. The NPs promoted mucosal healing by ameliorating ulcerative damage, restoring the histoarchitecture of gastric mucosa, and inhibiting pro-inflammatory cytokines such as tumor necrosis factor-α (TNF-α), interleukin-1 beta (IL-1β), and other inflammatory biomarkers such as myeloperoxidase (MPO) activity and nitric oxide (NO) levels. The current study's findings suggest that cellulose-conjugated Cu^I/IIO NPs exerted antiulcer effects on the preclinical rat model and have promising potential as a novel therapeutic agent for the treatment of gastric ulcers.

Novel sustainable filter for virus filtration and inactivation

The COVID-19 pandemic has caused a multi-scale impact on the world population that started from a nano-scale respiratory virus and led to the shutdown of macro-scale economies. Direct transmission of SARS-CoV-2 (Severe Acute Respiratory Syndrome Coronavirus 2) and its variants through aerosolized droplets is a major contributor towards increasing cases of this infection. To curb the spread, one of the best engineered solutions is the use of face masks to prevent the passage of infectious saliva micro-droplets from an infected person to a healthy person. The commercially available masks are single use, passive face-piece filters. These become difficult to breathe in during strenuous activities. Also, they need to be disposed regularly due to accumulation of unwanted particulate and pathogens over time. Frequent disposal of these masks is unsustainable for the environment. In this study, we have proposed a novel design for a filter for enhanced virus filtration, better breathability, and virus inactivation over time. The filter is called Hy–Cu named after its (Hy) drophobic properties and another significant layer comprises of copper (Cu). The breathability (pressure drop across filter) of Hy–Cu is tested and compared with widely used surgical masks and KN95 masks, both experimentally and numerically. The results show that the Hy–Cu filter offers at least 10% less air resistance as compared to commercially available masks. The experimental results on virus filtration and inactivation tests using MS2 bacteriophage (a similar protein structure as SARS-CoV-2) show that the novel filter has 90% filtering efficiency and 99% virus inactivation over a period of 2 h. This makes the Hy–Cu filter reusable and a judicious substitute to the single use masks.

Engineering biomaterials to 3D-print scaffolds for bone regeneration: practical and theoretical consideration

There are more than 2 million bone grafting procedures performed annually in the US alone. Despite significant efforts, the repair of large segmental bone defects is a substantial clinical challenge which requires bone substitute materials or a bone graft. The available biomaterials lack the adequate mechanical strength to withstand the static and dynamic loads while maintaining sufficient porosity to facilitate cell in-growth and vascularization during bone tissue regeneration. A wide range of advanced biomaterials are being currently designed to mimic the physical as well as the chemical composition of a bone by forming polymer blends, polymer-ceramic and polymer-degradable metal composites. Transforming these novel biomaterials into porous and load-bearing structures via three-dimensional printing (3DP) has emerged as a popular manufacturing technique to develop engineered bone grafts. 3DP has been adopted as a versatile tool to design and develop bone grafts that satisfy porosity and mechanical requirements while having the ability to form grafts of varied shapes and sizes to meet the physiological requirements. In addition to providing surfaces for cell attachment and eventual bone formation, these bone grafts also have to provide physical support during the repair process. Hence, the mechanical competence of the 3D-printed scaffold plays a key role in the success of the implant. In this review, we present various recent strategies that have been utilized to design and develop robust biomaterials that can be deployed for 3D-printing bone substitutes. The article also reviews some of the practical, theoretical and biological considerations adopted in the 3D-structure design and development for bone tissue engineering.

Cu(II)-functionalized silk fibroin films for the catalytic generation of nitric oxide

In situ release of nitric oxide (NO) has been suggested to be a potential functionalization strategy for blood-contacting implants. In this study, the NO generation capability catalyzed by the copper ion-incorporated silk fibroin (SF) films in the presence of S-nitroso-N-acetyl-dl-penicillamine (SNAP) is demonstrated. Cu(II) is effectively bound to the surface of the SF film based on metal-protein coordination. The x-ray photoelectron spectroscopy results indicate that copper ions may exist on the surface of the SF film in the form of Cu(II)/Cu(I) coexistence. The degradation behavior showed that the bound copper ions on the surface of the SF films can maintain a slow release in phosphate-buffered saline (PBS) or collagenase IA solution for 7 days. There was no significant difference in the release of copper ions between PBS degradation and enzyme degradation. The loading of copper ions significantly improved the release of NO from SNAP through catalysis. Based on the biological effects of copper ions and the ability to catalyze the release of NO from S-nitrosothiols, copper ion loading provides an option for the construction of bioactive SF biomaterials.

Comparison of Physicochemical, Mechanical, and (Micro-)Biological Properties of Sintered Scaffolds Based on Natural- and Synthetic Hydroxyapatite Supplemented with Selected Dopants

The specific combinations of materials and dopants presented in this work have not been previously described. The main goal of the presented work was to prepare and compare the different properties of newly developed composite materials manufactured by sintering. The synthetic- (SHAP) or natural- (NHAP) hydroxyapatite serves as a matrix and was doped with: (i) organic: multiwalled carbon nanotubes (MWCNT), fullerenes C60, (ii) inorganic: Cu nanowires. Research undertaken was aimed at seeking novel candidates for bone replacement biomaterials based on hydroxyapatite—the main inorganic component of bone, because bone reconstructive surgery is currently mostly carried out with the use of autografts; titanium or other non-hydroxyapatite -based materials. The physicomechanical properties of the developed biomaterials were tested by Scanning Electron Microscopy (SEM), Dielectric Spectroscopy (BSD), Nuclear Magnetic Resonance (NMR), and Differential Scanning Calorimetry (DSC), as well as microhardness using Vickers method. The results showed that despite obtaining porous sinters. The highest microhardness was achieved for composite materials based on NHAP. Based on NMR spectroscopy, residue organic substances could be observed in NHAP composites, probably due to the organic structures that make up the tooth. Microbiology investigations showed that the selected samples exhibit bacteriostatic properties against Gram-positive reference bacterial strain S. epidermidis (ATCC 12228); however, the property was much less pronounced against Gram-negative reference strain E. coli (ATCC 25922). Both NHAP and SHAP, as well as their doped derivates, displayed in good general compatibility, with the exception of Cu-nanowire doped derivates.

Development of Silver-Containing Hydroxyapatite-Coated Antimicrobial Implants for Orthopaedic and Spinal Surgery

The prevention of surgical site infections is directly related to the minimization of surgical invasiveness, and is in line with the concept of minimally invasive spine therapy (MIST). In recent years, the incidence of postoperative infections has been increasing due to the increased use of spinal implant surgery in patients at high risk of infection, including the elderly and easily infected hosts, the limitations of poor bone marrow transfer of antibiotics, and the potential for contamination of surgical gloves and instruments. Thus, the development of antimicrobial implants in orthopedic and spinal surgery is becoming more and more popular, and implants with proven antimicrobial, safety, and osteoconductive properties (i.e., silver, iodine, antibiotics) in vitro, in vivo, and in clinical trials have become available for clinical use. We have developed silver-containing hydroxyapatite (Ag-HA)-coated implants to prevent post-operative infection, and increase bone fusion capacity, and have successfully commercialized antibacterial implants for hip prostheses and spinal interbody cages. This narrative review overviews the present status of available surface coating technologies and materials; describes how the antimicrobial, safety, and biocompatibility (osteoconductivity) of Ag-HA-coated implants have been demonstrated for commercialization; and reviews the clinical use of antimicrobial implants in orthopedic and spinal surgery, including Ag-HA-coated implants that we have developed.

Development and characterization of cannabidiol-loaded alginate copper hydrogel for repairing open bone defects in vitro

The clinical treatment of open bone defects caused by accidental bone trauma, bone tumors, bone diseases and bone infections is challenging. In this study, we designed and fabricated a multifunctional alginate-based hydrogel that contains cannabidiol (CBD), SA@Cu/CBD hydrogel, for repairing open bone defects. The results of physicochemical characterization showed that the SA@Cu/CBD hydrogel was successfully prepared and showed a suitable swelling ratio, high thermal stability, and stable mechanical properties. In vitro evaluation of antibacterial activity indicated that more than 90% of S. aureus and E. coli were inhibited compared to the control group. The ALP activity assay showed that the ALP expression level of MC3T3-E1cells in SA@Cu/CBD hydrogel was approximately 2-fold higher than that in the control group on day 7 and 14. Additionally, compared to the control group, the level of mineralized deposits in SA@Cu/CBD hydrogel was also improved by about 2 times on day 14. The PCR results indicated the mRNA expression levels of osteogenic markers (ALP, Col1α1, OCN, and RUNX2 genes) and angiogenic markers (EGFL6 and VEGF genes) in SA@Cu/CBD hydrogel were significantly upregulated compared to that in the control group, and the mRNA expression levels of critical inflammatory cytokines (TNF-α and IL-1β) in the SA@Cu/CBD hydrogel were significantly down-regulated compared to that in SA@Cu hydrogel. Taken together, these results demonstrated that the SA@Cu/CBD hydrogel showed significantly anti-bacterial, anti-inflammation, angiogenic and osteogenic activities in vitro studies. Thus, SA@Cu/CBD hydrogels may be a promising candidate in repairing open bone defects.

Precise Anti-Tumor Effect of a Metallopolysaccharide-Based Nanotheranostic: Turning Phototherapy into Programmed Chemotherapy

Phototheranostic, a regional-focused treatment, can endow cancer theranostic with low damage due to its spatial precision. However, precise elimination of residual cancer cells in laser-focused field and in non-laser-focused field...

Recent Advances in Copper-Catalyzed C-N Bond Formation Involving N-Centered Radicals

C-N bonds are pervasive throughout organic-based materials, natural products, pharmaceutical compounds, and agricultural chemicals. Considering the widespread importance of C-N bonds, the development of greener and more convenient ways to form C-N bonds, especially in late-stage synthesis, has become one of the hottest research goals in synthetic chemistry. Copper-catalyzed radical reactions involving N-centered radicals have emerged as a sustainable and promising approach to build C-N bonds. As a chemically popular and diverse radical species, N-centered radicals have been used for all kinds of reactions for C-N bond formation by taking advantage of their inherently incredible reactive flexibility. Copper is also the most abundant and economic catalyst with the most relevant activity for facilitating the synthesis of valuable compounds. Therefore, the aim of the present Review was to illustrate recent and significant advances in C-N bond formation methods and to understand the unique advantages of copper catalysis in the generation of N-centered radicals since 2016. To provide an ease of understanding for the readers, this Review was organized based on the types of nitrogen sources (amines, amides, sulfonamides, oximes, hydrazones, azides, and tert-butyl nitrite).

Antiviral properties of copper and its alloys to inactivate covid-19 virus: a review

Copper (Cu) and its alloys are prospective materials in fighting covid-19 virus and several microbial pandemics, due to its excellent antiviral as well as antimicrobial properties. Even though many studies have proved that copper and its alloys exhibit antiviral properties, this research arena requires further research attention. Several studies conducted on copper and its alloys have proven that copper-based alloys possess excellent potential in controlling the spread of infectious diseases. Moreover, recent studies indicate that these alloys can effectively inactivate the covid-19 virus. In view of this, the present article reviews the importance of copper and its alloys in reducing the spread and infection of covid-19, which is a global pandemic. The electronic databases such as ScienceDirect, Web of Science and PubMed were searched for identifying relevant studies in the present review article. The review starts with a brief description on the history of copper usage in medicine followed by the effect of copper content in human body and antiviral mechanisms of copper against covid-19. The subsequent sections describe the distinctive copper based material systems such as alloys, nanomaterials and coating technologies in combating the spread of covid-19. Overall, copper based materials can be propitiously used as part of preventive and therapeutic strategies in the fight against covid-19 virus.

Experiments and simulation of co-migration of copper-resistant microorganisms and copper ions in saturated porous media

Heavy metal (HV) pollutants may migrate to the groundwater environment through leaching, causing groundwater pollution. Compared with surface water pollution, groundwater pollution is complex and hidden. Existing methods for treating HV pollution in the vadose zone have had limited application owing to various problems. In recent years, microorganisms have been used in the field of pollution control and remediation owing to their outstanding adsorption and degradation properties and low cost, but their environmental safety and behavior in porous media are still poorly understood. This study aimed to investigate the migration behavior and mechanisms of copper ions in saturated porous media under the action of copper-resistant microorganisms and to establish a corresponding numerical model to simulate the results. The key parameters of adsorption and migration were determined through batch adsorption and soil column experiments. A one-dimensional soil column was used to conduct a co-migration experiment using copper-resistant microorganisms and Cu²⁺ in water-saturated quartz sand, and a co-migration mathematical model was constructed. It was found that the existence of microorganisms had an inhibitory effect on the migration of Cu²⁺ in quartz sand, and Cu²⁺ promoted the migration of microorganisms, reduced their adsorption, and increased their concentration in the column experiment effluent. The selected solute transport mathematical model had a good fitting effect on the breakthrough curves of copper ion and copper-resistant microorganisms during their co-migration. The results can provide parameters and a theoretical basis for the risk assessment and prevention of HV pollution in the saturated zone or aquifers.

Virus-inspired surface-nanoengineered antimicrobial liposome: A potential system to simultaneously achieve high activity and selectivity

Enveloped viruses such as SARS-CoV-2 frequently have a highly infectious nature and are considered effective natural delivery systems exhibiting high efficiency and specificity. Since simultaneously enhancing the activity and selectivity of lipopeptides is a seemingly unsolvable problem for conventional chemistry and pharmaceutical approaches, we present a biomimetic strategy to construct lipopeptide-based mimics of viral architectures and infections to enhance their antimicrobial efficacy while avoiding side effects. Herein, a surface-nanoengineered antimicrobial liposome (SNAL) is developed with the morphological features of enveloped viruses, including a moderate size range, lipid-based membrane structure, and highly lipopeptide-enriched bilayer surface. The SNAL possesses virus-like infection to bacterial cells, which can mediate high-efficiency and high-selectivity bacteria binding, rapidly attack and invade bacteria via plasma membrane fusion pathway, and induce a local "burst" release of lipopeptide to produce irreversible damage of cell membrane. Remarkably, viral mimics are effective against multiple pathogens with low minimum inhibitory concentrations (1.6-6.3 μg mL-1), high bactericidal efficiency of >99% within 2 h, >10-fold enhanced selectivity over free lipopeptide, 99.8% reduction in skin MRSA load after a single treatment, and negligible toxicity. This bioinspired design has significant potential to enhance the therapeutic efficacy of lipopeptides and may create new opportunities for designing next-generation antimicrobials.

Significance of entropy generation and heat source: the case of peristaltic blood flow through a ciliated tube conveying Cu-Ag nanoparticles using Phan-Thien-Tanner model

The present speculative investigation is concentrated to analyze the entropy generation and heat transfer phenomena in ciliary induced peristalsis of blood with the suspension of hybrid nanoparticles in a tube with heat source impact. The blood is assumed to contain copper (Cu) and silver (Ag) nanoparticles (NPs). The ciliary inner wall of the tube has been considered with small hair-like structures. The Phan-Thien-Tanner (PTT) fluid model is employed to describe the non-Newtonian rheological characteristics of blood. The conservative equations are normalized and simplified by utilizing scaling analysis with the assumption of low Reynolds number and large wavelength approximations. The analytical inspection exposes that the total entropy generation gets a decrement for mounting values of cilia length, while reversed impact is detected for an increment in heat source parameter. Hybrid nano-blood exhibits a greater total entropy number than mono nano-blood. This research study may be beneficial to medical experts and researchers in the field of embryology. Cysts in the ciliated fallopian tube, where embryos develop, are removed by using nanoparticles (nano-drug delivery).