Batch and column studies of biosorption of heavy metals by Caulerpa lentillifera

A biogenic hydrogel to recover Au(III) from electronic waste

In the course of this investigation, we undertook the contemplation of a green chemistry paradigm with the express intent of procuring valuable metal, namely gold, from electronic waste (e-waste). In pursuit of this overarching objective, we conceived a procedural framework consisting of two pivotal stages. As an initial stage, we introduced a physical separation procedure relying on the utilization of the Eddy current separator, prior to embarking on the process of leaching from e-waste. Subsequent to the partitioning of metals from the non-metal constituents of waste printed circuit boards (PCB), we initiated an investigation into the hydrogel derived from basil seeds (Ocimum basilicum L.), utilizing it as a biogenic sorbent medium. The thorough characterization of hydrogel extracted from basil seeds involved the application of an array of analytical techniques, encompassing FTIR, XRD, SEM, and BET. The batch sorption experiments show more than 90% uptake in the pH range of 2-5. The sorption capacity of the hydrogel material was evaluated as 188.44 mg g-1 from the Langmuir Isotherm model. The potential interference stemming from a spectrum of other ions, encompassing Al, Cu, Ni, Zn, Co, Cr, Fe, Mn, and Pb was systematically examined. Notably, the sole instance of interference in the context of adsorption of gold ions was observed to be associated with the presence of lead. The application of the hydrogel demonstrated a commendable efficiency in the recovery of Au(III) from the leached solution derived from the waste PCB.

Interaction between Haematococcus pluvialis microalgae and lead nitrate: lead adsorption from water

Our study aims to investigate the response of the unicellular alga, Haematococcus pluvialis, to the toxicity of lead and propose a low-cost, highly efficient biological adsorbent for the purification of wastewater and lead-contaminated water. The first part examines the effects of lead toxicity on certain physiological indicators of this alga. In the second part, the potential of this alga in lead removal and its adsorption capacity was assessed. The alga was cultivated in a BG11 medium and treated with lead nitrate concentrations of 10, 50, and 200 mg/L during its exponential growth. The results showed that with an increase in lead concentration up to 200 mg/L, the growth rate, chlorophyll a, chlorophyll b, carotenoid and total protein content decreased, while malondialdehyde (MDA) content increased. The astaxanthin content slightly increased at the 10 mg/L but decreased at the 200 mg/L treatment. Maximum lead adsorption was observed at 98.69% under optimal conditions, including a pH of 6, an adsorbent dose of 1 g/L, a lead concentration of 25 mg/L, a temperature of 25 °C, and an exposure time of 120 min. The results of this study demonstrate that Haematococcus pluvialis has the potential for effective lead removal from aquatic environments.

Longevity prediction of reactive media in permeable reactive barriers considering the contamination level and groundwater velocity at the planning site, with a focus on cadmium removal by zeolite

Zeolite is a versatile and effective reactive material used in permeable reactive barriers (PRBs) for remediating groundwater contaminated with heavy metals. In this study, we evaluated the influence of subsurface environmental conditions, namely contamination level (C0) and groundwater velocity (v), on predicting the longevity of zeolite for cadmium (Cd) removal. Batch experiments were performed to investigate the effect of C0 on Cd removal, and column experiments were performed to examine how Cd transportation through zeolite varies at different C0 and v. Breakthrough curves (BTCs) were analyzed with an advection-dispersion equation (ADE) coupled with nonequilibrium sorption rate models. The reaction parameters indicating the performance metrics of zeolite were determined using an iterative fitting approach-retardation factor (R), partitioning coefficient (β), and mass transfer coefficient (ω). R exhibited dependence on C0, but was unrelated to v; its rapid increase at lower C0 was explained by Langmuir sorption isotherms. β and ω, integral to sorption dynamics and mass transfer, respectively, showcased functional relationships with v. β decreased gradually as v increased, described by the nonequilibrium sorption model, whereas ω increased steadily with v, guided by the Monod function. Using the relationship of these parameters, the fate and transport of Cd within zeolite was simulated under various subsurface environmental conditions to construct the longevity prediction function. Thus, this study introduces a method for predicting the longevity of reactive materials, which can be valuable for designing PRBs with high longevity in the future.

Performance expectation of coal waste in permeable reactive barrier for removal of cadmium considering contamination level and pore water velocity

The effectiveness and longevity of permeable reactive barriers (PRBs) depend on the performance of the reactive materials and the subsurface environment. The relationship of the groundwater velocity on performance of coal waste for the heavy metal removal was reported in our previous study. In this study, we investigated the performance and longevity of coal waste as a PRB material for the removal of Cd considering subsurface environmental conditions such as contamination level and groundwater velocity. The artificial groundwater contaminated by Cd were prepared with various concentrations ranging from 10 to 100 mg L-1. Lab-scale column experiments were conducted using coal waste filled columns by injecting the artificial groundwater. The breakthrough curves were analyzed advection dispersion equation coupled with equilibrium sorption model to determine the retardation factor. The Cd breakthrough curves exhibited different retardation with respect to the contamination levels. The Cd transport was more retarded as the contamination level lowered. The relationship between the retardation factor and the contamination levels could be explained with empirical equations based on non-linear sorption isotherms. By adopting the velocity dependency of sorbent performance in our previous study, transport of Cd within coal waste was simulated under various subsurface environmental conditions to construct the longevity function. The function could be used for the longevity prediction of coal waste as a PRB material considering groundwater velocity and contamination level in subsurface environment.

Prediction of heavy metal biosorption mechanism through studying isotherm kinetic equations

The kinetic constants for free and immobilized cells were determined by measuring reaction rates at different metal concentrations at the optimum reaction conditions. (K_max and V_max) were calculated from the slope and intercept of the straight lines. The pseudo-second-order rate constants are derived based on the sorption capacity of the solid phase, where K2 is the rate constant for the pseudo-second-order model. Determined experimentally by plotting t/q against t. The mean free vitality of adsorption (E) was figured as 2.62 kJ mol^-1 and the extent of E communicated gives data on the adsorption mechanism. An E value ranging from 1 to 8 indicates physisorption and 8-16 kJ mol^-1 predicts ion exchange. Thus, the evaluated value of 2.62 kJ mol^-1 predicts the phenomenon of physisorption, which suggests that metal ions were favorably adsorbed by this biosorbent in a multi-layer fashion. The overall result suggested that 98.2% of U (VI) by biosorption of U in the mechanism of adsorption will include chemisorption mechanistic pathway: Langmuir, Freundlich, equations and the values of K_f 5.791 where K_L 3.9 were determined from the linear plot of log q_e vs. log C_e at 30 °C, indicating that metal ions were favorably adsorbed by this biosorbent in a multi-layer fashion and instrumentation of beads characterizing novel Binding sites using FTIR & SEM beside change in peaks position which assigned for its groups confirm biosorption of metal.

A review on bismuth-based materials for the removal of organic and inorganic pollutants

Modernized lifestyle and increased industrialization threaten living organisms because of the pollutants released from industries and household wastes. The presence of even small amounts of pollutants (organic pollutants (OPs) and inorganic pollutants-heavy metals (HMs)) shows significant effects. Thus wastewater treatment is urgently needed before being subjected to use. Many methods and materials have been developed and reported for the removal of pollutants from wastewater. This review focused on the removal of both OPs and HMs using bismuth-based (Bi-based) materials because of their low toxicity and excellent properties compared to other metals. Bi-based materials as a photocatalyst for photodegradation of OPs are discussed in detail with synthesis methods. Further, since few reviews are available on the Bi-based material for the removal and sensing of HMs, this topic was intentionally summarized. About 200 published articles and reviews have been reviewed here. Additionally, the key point that needs to be focused on the development of Bi-based photocatalysts for the removal of OPs and for upgrading the Bi-based materials as adsorbents for HMs are conferred in the outlook. This will help many researchers in their upcoming work.

Photosynthetic, Molecular and Ultrastructural Characterization of Toxic Effects of Zinc in Caulerpa racemosa Indicate Promising Bioremediation Potentiality

Caulerpaceae are unconventional green algae composed of multinucleated, single siphonous cells. The species of Caulerpa are acquiring major scientific interest for both their invasion in the Mediterranean ecological niche and for the production of valuable natural metabolites. Furthermore, the abilities of Caulerpa spp. in the biorecovery of polluted waters were recently investigated. Among heavy metal contaminants in marine systems, zinc (Zn) is considered a critical pollutant, progressively accumulating from plastic leachates. In this study, the responses of Caulerpa racemosa to different levels (5-10 mg L^-1) of Zn were studied for 14 days under laboratory-controlled conditions. Effects of Zn were monitored by measuring the growth rate, photosynthetic efficiency and gene expression. Moreover, the ability of Caulerpa to remove Zn from seawater was monitored. Zn induced detrimental effects by decreasing the relative growth rate (RGR) and maximal PSII photochemical efficiency (F_v/F_m). Moreover, C. racemosa, grown in contaminated seawater, reduced the levels of Zn to a final concentration of 1.026 and 1.932 mg L^-1 after 14 days, thus demonstrating efficient uptake. Therefore, our results characterized the effects of zinc on C. racemosa and the possible role of this alga as being effective in the bioremediation of marine seawater.

Heavy metal biosorption by Extracellular Polymeric Substances (EPS) recovered from anammox granular sludge

The recovery and conversion of Extracellular Polymeric Substances (EPS) from sewage sludge into bio-based commodities might improve the economics and environmental sustainability of wastewater treatment. This contribution explores the application of EPS from anammox granular waste sludge as biosorbent for the removal of heavy metals, specifically lead, copper, nickel, and zinc. Adsorption capacities equivalent or higher than well-established adsorbent media emerged from single-metal biosorption studies (up to 84.9, 52.8, 21.7 and 7.4 mg/gTS_EPS for Pb²⁺, Cu²⁺, Ni²⁺ and Zn²⁺, respectively). Combining spectroscopic techniques, a mechanistic hypothesis for metal biosorption, based on a combination of electrostatic interaction, ion exchange, complexation, and precipitation, was proposed. The adsorption mechanisms of extracted EPS and non-extracted EPS in the native biomass were indirectly compared by means of single-metal biosorption studies performed with pristine granules (adsorbing up to 103.7, 36.1, 48.2 and 49.8 mg/gTSgranules of Pb²⁺, Cu²⁺, Ni²⁺, and Zn²⁺, respectively). In comparison with pristine anammox granules, EPS showed lower adsorption capacities except for copper and different adsorption pathways as postulated based on the adsorption data interpretation via theoretical models. The multi-metal biosorption tests excluded significant competitions among different heavy metals for the EPS binding sites, thus opening further scenarios for the treatment of complex wastewaters.

Adsorption-Desorption Surface Bindings, Kinetics, and Mass Transfer Behavior of Thermally and Chemically Treated Great Millet Husk towards Cr(VI) Removal from Synthetic Wastewater

This study reports the efficacy of adsorbents synthesized by thermal (TT-GMH) and chemical (CT-GMH) modification of great millet husk (GMH) for the treatment of synthetic wastewater containing Cr(VI). The chemical modification of raw GMH was done by concentrated H2SO4 to increase the porosity and heterogeneity on the surface. The comparative investigations of physicochemical properties of synthesized adsorbents were examined by point of zero charge (pHpzc), BET surface area, SEM-EDX, FTIR, and XRD analyses. The results revealed that CT-GMH had around three times higher surface area and more porous structure as compared to TT-GMH. The adsorption experiments were executed in batch mode to examine the impact of parameters governing the adsorption process. For Cr(VI) solution of 25 mg/L, adsorbent dose of 4 g/L, temperature of 25 ${}^{°}\text{C}$ , and shaking speed of 150 RPM, the maximum removal for TT-GMH was attained at pH 1 and contact time 150 min, while for CT-GMH, maximum removal was attained at pH 2 and contact time 120 min. The experimental results fitted to the rate kinetic equations showed that for both TT-GMH and CT-GMH, adsorbents followed the quasi-second-order kinetic model during the adsorption process. Further, results revealed that the adsorption process was endothermic and Sips isotherm model was followed for both TT-GMH and CT-GMH. Based on the Sips isotherm, maximum uptake capacity for TT-GMH and CT-GMH was noted to be 16 and 22.21 mg/g, respectively. Among the tested mass transfer models, liquid film diffusion model was followed during the adsorption process of both the adsorbents. The desorption study revealed that TT-GMH and CT-GMH give 69.45% and 74.48% removal, respectively, up to six cycles.

Coeffect of pyrolysis temperature and potassium phosphate impregnation on characteristics, stability, and adsorption mechanism of phosphorus-enriched biochar

Potassium phosphate (K₃PO₄)-impregnated bamboo was pyrolyzed at temperatures ranging from 350 to 950 °C to explore the coeffect of pyrolysis temperature and K₃PO₄ impregnation on biochar's characteristics and adsorption behavior. The degree of aromatization and graphitization in phosphorus-enriched biochars (PRBCs) rose as temperature increased, whereas H/C and O/C ratios, pH value, and O-containing group content decreased. The pre-aging impact of K₃PO₄ impregnation results in increased stability and adsorption performance of PRBCs. Adsorption mechanism of PRBCs to heavy metal varies from pyrolysis temperature. Micropores dominate medium-temperature PRBCs (prepared at 550 ∼ 750 °C), possessing the highest P-containing group content (116 % that of PRBC-350) and maximal adsorption capacity (greater than289 mg/g). The medium-temperature PRBCs adsorb Cd (II) via the role of O-containing groups, PO₄^3-, and P₂O₇^4-, mainly by reactions of organic complexation, precipitation and inorganic complexation, respectively. 550 °C is the optimal pyrolysis temperature for both energy saving and heavy metal adsorption.

Cleaner technologies to combat heavy metal toxicity

Heavy metals frequently occur as silent poisons present in our daily diet, the environment we live and the products we use, leaving us victims to various associated drastic health and ecological bad effects even in meagre quantities. The prevalence of heavy metals can be traced from children's toys, electronic goods, industrial effluents, pesticide preparation, and even in drinking water in some instances; necessitating methods to remediate them. The current review discusses the various physicochemical and biological methods employed to tackle the problem of heavy metal pollution. Apart from the conventional methods following the principles of adsorption, precipitation, coagulation, and various separation techniques, the advancements made in the directions of biological heavy metal detoxification using microbes, plants, algae have been critically analyzed to identify the specific utility of different agents for specific heavy metal removal. The review paper is a nutshell of different heavy metal remediation strategies, their merits, demerits, and modifications done to alleviate process of heavy metal pollution.

Removal of Heavy Metals (Cd2+, Cu2+, Ni2+, Pb2+) from Aqueous Solution Using Hizikia fusiformis as an Algae-Based Bioadsorbent

This study investigated the applicability of algae (Hizikia fusiformis, Green gracilaria, and Codium fragile) for removing heavy metals (Cd2+, Cu2+, Ni2+, and Pb2+) from aqueous solutions. Among the algae, H. fusiformis was chosen as a bioadsorbent and modified with NaOH and HCl. The results showed that the biosorption capacity of H. fusiformis improved significantly after treatment with NaOH; however, H. fusiformis modified with HCl did not achieve the expected value. The NaOH treatment enhanced the biosorption of metals on the treated H. fusiformis because of the hydrolysis reaction producing carboxylic (–COOH) and hydroxyl groups (–OH). The kinetics for Cd2+, Cu2+, Ni2+, and Pb2+ biosorption well fitted to pseudo-first-order, pseudo-second-order, and Elovich models, with R2 of >0.994. The Freundlich model provided a good fit for the equilibrium biosorption of Cd2+, Cu2+, and Ni2+ by both algae and the Langmuir model for Pb2+. The maximum biosorption of metals was in the order Pb2+ >> Cu2+ ≈ Ni2+ > Cd2+, with qmax of 167.73, 45.09, 44.38, and 42.08 mg/g, respectively. With an increase in the solution pH, metal biosorption was enhanced, and considerable enhancement was observed in the pH range of 2–4. Thus, H. fusiformis is expected to be considered a superior candidate for metal biosorption.

Electrochemical Column Cell for Continuous Oxidative Inactivation of Pathogens and Reductive Removal of Toxic Heavy Metals

A solar-driven electrochemical column (EC) was developed for cathodic sequestration remediation of heavy metals (HMs) and anodic electroporative inactivation of pathogenic bacteria (PB) with continuous flow capacity for sustainable production of drinking water from wastewater. The method produces "revitalized drinking water" by keeping its natural mineral nutrients boosted with dissolved oxygen. The EC was constructed with graphene oxide (GO) synthesized via photoassisted electrochemical oxidation of CF (PEGO-CF) as the cathode and phytoreduced GO (RPEGO-CF) as the anode. In the EC, effluent is passed upward through the microchannel of CF electrodes to obtain a higher contact time with water molecules, enabling deposition of HMs and oxidative inactivation of PB, collectively termed electroadsorptive dialysis (EAD). PEGO-CF and RPEGO-CF stacked inside the EC resulted in the increased surface area and thereby the removal efficiency. Reactive oxygen species (ROS) produced at the anode damaged the bacterial cell sheath, while the oxygen functional group and the cathodic negative potential had a concurrent effect in "sequestration" of HMs. Density functional calculations showed that PEGO might transfer an electron from the highest occupied molecular orbital (HOMO) to the lowest unoccupied molecular orbital (LUMO) under applied negative potential leading to internal system crossing to the vacant d-orbitals of HMs, allowing for simultaneous coordination and deposition. The EC produced 313 L of revitalized water from wastewater augmented with 500 μg L^-1 HMs and 10⁷ CFU mL^-1 pathogenic bacteria (Escherichia coli and Staphylococcus aureus). Only a 3.6 J energy investment produced 1 L of revitalized water, which is ∼2000 times less than the usual energy consumption by electroporation and the lowest value obtained to date for bacterial inactivation with heavy metal removal. Laboratory-to-industrial scale-up calculations were performed for this water-purifying technology involving a water-energy nexus, promising high-efficiency bacterial inactivation, and HM remediation to obtain energy-efficient clean and revitalized water.

Electrochemical recovery and high value-added reutilization of heavy metal ions from wastewater: Recent advances and future trends

Wastewater treatment for heavy metals is currently transitioning from pollution remediation towards resource recovery. As a controllable and environment-friendly method, electrochemical technologies have recently gained significant attention. However, there is a lack of systematic and goal oriented summarize of electrochemical metal recovery techniques, which has inhibited the optimized application of these methods. This review aims at recent advances in electrochemical metal recovery techniques, by comparing different electrochemical recovery methods, attempts to target recycling heavy metal resources with minimize energy consumption, boost recovery efficiency and realize the commercial application. In this review, different electrochemical recovery methods (including E-adsorption recovery, E-oxidation recovery, E-reduction recovery, and E-precipitation recovery) for recovering heavy metals are introduced, followed an analysis of their corresponding mechanisms, influencing factors, and recovery efficiencies. In addition, the mass transfer efficiency can be promoted further through optimizing electrodes and reactors, and multiple technologies (photo-electrochemical and sono-electrochemical) could to be used synergistically improve recovery efficiencies. Finally, the most promising directions for electrochemical recovery of heavy metals are discussed along with the challenges and future opportunities of electrochemical technology in recycling heavy metals from wastewater.

Sulfide remediation from wastewater using hydrothermally synthesized δ-MnO2/porous graphitic carbon as adsorbent

A facile hydrothermal assisted in-situ precipitation technique was employed for synthesizing highly efficient porous graphitic carbon/manganese dioxide (PGC/MnO₂) nanocomposite adsorbent using calcium alginate as carbon precursor. Morphological and structural characterization using scanning electron microscopy equipped with energy dispersive X-ray spectroscopy, transmission electron microscopy, and X-ray diffraction techniques confirmed the interconnected nanoporous architecture and birnessite (δ) MnO₂ polymorph evenly distributed on the PGC structure. The synergistic effect of PGC and MnO₂ was exploited for enhanced sulfide removal from wastewater via adsorptive oxidation. The effect of different experimental parameters, including solution pH, initial sulfide concentration, adsorbent dosage, and contact time on removal efficiency was investigated. The equilibrium and kinetic data for sulfide adsorption by PGC/MnO₂ nanocomposite fitted well with Langmuir isotherm and pseudo-second-order kinetic model, respectively. The maximum uptake capacity of sulfide by the nanocomposite was determined as 500 mg/g with complete sulfide removal. Further, it was estimated that a typical field application using the synthesized nanocomposite adsorbent would require 0.5-1 g/L per 200 mg/L of sulfide contaminated wastewater. Based on the experimental results, a schematic of the adsorptive oxidation mechanism of PGC/MnO₂ nanocomposite is proposed.

Electric conversion treatment of cobalt-containing wastewater

Long-term accumulation of cobalt-containing wastewater may also pollute groundwater and cause a large amount of loss of valuable metals. Therefore, the comprehensive utilization of cobalt-containing wastewater must be realized, especially as cobalt itself is a very important strategic resource. This paper proposes a membrane electroconversion method to separate cobalt ions from cobalt-containing wastewater and prepare cobalt hydroxide. In addition, the electrolysis process was optimized, and single-factor experiments such as the initial concentration, cobalt ions, current density, temperature etc., and economic calculations such as current efficiency were explored. The electrolysis product was calcined as the precursor to obtain the oxide Co₃O₄, and the calcination experiment was also optimized. In this concentration range, more than 90% of cobalt can be recovered within 2 h.

Removal of Heavy Metal Ions from Wastewaters: An Application of Sodium Trithiocarbonate and Wastewater Toxicity Assessment

The synthesis and application of sodium trithiocarbonate (Na2CS3) for the treatment of real galvanic wastewater in order to remove heavy metals (Cu, Cd and Zn) was investigated. A Central Composite Design/Response Surface Methodology (CCD/RSM) was employed to optimize the removal of heavy metals from industrial wastewater. Adequacy of approximated data was verified using Analysis of Variance (ANOVA). The calculated coefficients of determination (R2 and R2adj) were 0.9119 and 0.8532, respectively. Application of Na2CS3 conjugated with CCD/RSM allowed Cu, Cd and Zn levels to be decreased and, as a consequence, ∑Cu,Cd,Zn decreased by 99.80%, 97.78%, 99.78%, and 99.69%, respectively, by using Na2CS3 at 533 mg/L and pH 9.7, within 23 min. Implementation of conventional metal precipitation reagents (NaOH, Ca(OH)2 and CaO) at pH 11 within 23 min only decreased ∑Cu,Cd,Zn by 90.84%, 93.97% and 93.71%, respectively. Rotifer Brachionus plicatilis was used to conduct the assessment of wastewater toxicity. Following the application of Na2CS3, after 60 min the mortality of B. plicatilis was reduced from 90% to 25%. Engagement of Na2CS3 under optimal conditions caused the precipitation of heavy metals from the polluted wastewater and significantly decreased wastewater toxicity. In summary, Na2CS3 can be used as an effective heavy metal precipitating agent, especially for Cu, Cd and Zn.

Spent mushroom substrate: a crucial biosorbent for the removal of ferrous iron from groundwater

Abstract

A new approach was carried out with the spent mushroom substrate (SMS) of Pleurotus florida on ferrous iron (Fe2+) removal using live, dead and pretreated substrate. In this study, the various dosage levels of SMS namely, 0.25, 0.50, 1.0 and 1.50 g/50 mL were used for the removal of Fe2+ at different time intervals for 90 min. The effect of various temperatures and pH on Fe2+ removal was studied with optimized dosages and time intervals. The biosorption potential of P. florida SMS was checked against the iron-contaminated groundwater collected from in and around Salem, Namakkal and Dharmapuri districts of Tamil Nadu. The biosorption data were obtained and analyzed in terms of their kinetic behavior. Among the SMS of P. florida, the live SMS showed potential Fe2+ removal (100%) from aqueous metal solution in all the tested concentrations. SMS of P. florida showed high potential removal of Fe2+ in neutral pH, at room temperature and explored an efficient sorption ability (100%) in the tested water sample (SW10). The adsorption kinetic values fitted very well with pseudo-second-order when comparing with pseudo-first-order reaction. FTIR, SEM and EDX analysis proved the accumulation of Fe2+ by the SMS. The present study confirmed that the live SMS of P. florida may serve as a potential and eco-friendly biosorbent for removal of Fe2+ from the iron-contaminated water.

Graphic abstract

Mercury interactions with algal and plastic microparticles: Comparative role as vectors of metals for the mussel, Mytilus galloprovincialis

The adsorption and desorption of Hg onto and from microplastics (MP) and microalgae (MA) were investigated, and fitted using pseudo-first-order and pseudo-second order kinetics models. Then, the potential role of MP as vector for the entrance and accumulation of Hg (MP-Hg) in comparison to natural pathways (via MA -MA-Hg-, and dissolved -WB-Hg-) was investigated in mussel. Mussels were exposed to a single dose of Hg (2375 ng ind^-1) for 4 h. Although the clearance of MP-Hg was relevant (82 %), it was lower than that of MA (95 %) and MA-Hg (94 %). The amount of the Hg accumulated and eliminated was higher in mussels exposed to MP-Hg (1417 ng Hg) than in those exposed to MA-Hg (882 ng Hg) and WB-Hg (1074 ng Hg). However, Hg accumulation was similar in the three mussel groups (≈800 ng Hg). This was related to the fast elimination of Hg still attached to MP by MP-Hg mussels. Hg was mainly accumulated in digestive gland in MA-Hg and MP-Hg mussels, and in gills in WB-Hg mussels. Overall, the results indicated that MP facilitated the entrance of Hg in mussel but also promoted Hg elimination, which could limit the toxicological risk of Hg adsorbed onto MP.

Evaluation of Environmental Pollution and Microbial Treatment of Shallow Groundwater in El Omayed Area, Egypt

In the last few years, the northwestern coastal zone of Egypt has been affected by many stresses that impact its water resources, leading to undesirable consequences related to water quantity and quality. This paper aims to evaluate the possible contamination sources of shallow aquifers in the El-Omayed area, Egypt, that are causing its deterioration; this was achieved through an integration of hydrochemical and isotopic techniques, an assessment of the undesirable consequences of potential toxic metals (PTMs) on human health risk as a result of direct water consumption, and finally, the application of biological treatment in the remediation of some metal contamination. The chemical composition, environmental isotopes (δ¹⁸ O and δ² H), and microbial analyses were analyzed from 13 collected water samples. Approximately 20% of the groundwater samples were classified as fresh water, and the rest were classified as slightly saline to moderately saline. Stable isotopes proved the contribution of the El Sheikh Zoied canal (which is mainly recharged from the Nile system) as a recharge source. The toxicity of PTMs (Cd, Cu, Co, Cr, Pb, Zn, B, and Fe) was evaluated on the basis of their exceedance values. It was proven that the majority of the groundwater samples were contaminated, which might be attributed to natural and anthropogenic actions in the study area; however, according to human health risk exposure assessment calculations, there is no human cancer risk posed via ingestion of drinking groundwater. The total bacterial count was determined for all water samples; autochthonous microorganisms were capable of removing heavy metals in the polluted water sample. The bacterial strain M52, which was identified by 16S rRNA sequencing as Stenotrophomonas rhizophila, showed the best results, by removing 75% and 65% of the initial concentrations of Fe and B, respectively. The results indicate that this bacterial strain may be useful and represents an environmentally friendly method to remove pollutants and heavy metals from contaminated water. Integr Environ Assess Manag 2020;16:461-471. © 2020 SETAC.

Remarkably high Pb2+ binding capacity of a novel, regenerable bioremediator Papiliotrema laurentii RY1: Functional in both alkaline and neutral environments

The ability of P. laurentii strain RY1 to remediate lead (Pb²⁺) from water was investigated in batch and column studies. The lead removal ability of non-viable biomass, non-viable biomass immobilised on agar-agar (biobeads) and agar-agar at different pH was compared in batch studies. It was found that among the three, biobeads have maximum ability to remove Pb²⁺ followed by biomass and agar-agar beads. Maximum and almost equal lead removal by biobeads was observed at both neutral and alkaline pH making it a novel and more applicable bioremediator as all other reported bioremediators have a single pH for optimum activity. Studies were performed to determine the optimum conditions for lead removal from aqueous solutions for biobeads. The physical and chemical characterization of the biobeads before and after Pb²⁺ biosorption was done by using S.E.M. and F.T.I.R. respectively. The adsorption of Pb²⁺ on biobeads obeyed the Langmuir adsorption isotherm and pseudo first order kinetics. These mean that the Pb²⁺ binding sites are identical, located on the surface of the adsorbant and the rate of Pb²⁺ removal from aqueous solution is directly proportional to the number of Pb²⁺ binding sites on the biobeads. The thermodynamics of the biosorption process is also investigated. The binding capacity of the biobeads in batch study was found to be 52.91mg/gm which is higher in comparison to other reported yeast bioremediators. The used biobeads can be desorbed using 0.1(M) CaCl₂. The desorbed biobeads can be used subsequently for several cycles of lead removal making it cost-effective. Column studies were also performed for biobeads with the help of Thomas model for examining its suitability for industrial application. Maximum specific lead uptake of the biobeads when applied in the column was found to be 58.26mg/gm which being promising makes it suitable for application in industries involved in the treatment of wastewater contaminated with high amounts of lead. The high mass transfer co-efficient indicate that small sized column can be used effectively to remove high amounts of lead which makes the bioremediation process by the biobeads more economical and advantageous for industrial application. Several factors like effectiveness of the biobeads in Pb²⁺removal at both neutral and alkaline pH, reusability, high mass transfer co-efficient, regenerability and high binding capacity makes it a novel versatile, cost-effective and high utility bioremediator.

Adsorption kinetic models: Physical meanings, applications, and solving methods

Adsorption technology has been widely applied in water and wastewater treatment, due to its low cost and high efficiency. The adsorption kinetic models have been used to evaluate the performance of the adsorbent and to investigate the adsorption mass transfer mechanisms. However, the physical meanings and the solving methods of the kinetic models have not been well established. The proper interpretation of the physical meanings and the standard solving methods for the adsorption kinetic models are very important for the applications of the kinetic models. This paper mainly focused on the physical meanings, applications, as well as the solving methods of 16 adsorption kinetic models. Firstly, the mathematical derivations, physical meanings and applications of the adsorption reaction models, the empirical models, the diffusion models, and the models for adsorption onto active sites were analyzed and discussed in detail. Secondly, the model validity evaluation equations were summarized based on literature. Thirdly, a convenient user interface (UI) for solving the kinetic models was developed based on Excel software and provided in supplementary information, which is helpful for readers to simulate the adsorption kinetic process.

Biosorption Studies of Cd2+ and Cr6+ from Aqueous Solution Using Cola-Nut Leaves as Low-Cost Biosorbent

Cola-nut leaf is an agricultural waste which was used in this research as biosorbent for the adsorption of Cd2+and Cr6+ from aqueous solutions. The leaves of cola nut were modified using 0.1 M HCl. Modified cola nut leaves biosorbent showed slightly higher percentage sorption than the unmodified leaves, for both heavy metals with increasing contact time, having greater affinity for Cd2+. The equilibrium sorption data was attained using the batch technique with increased pH (9) and increased adsorbent dose (1 g/25 cm3 of adsorbate) and initial metal concentration. The functional group of cola nut leaves before and after adsorption was determined using Fourier Transform Infrared Spectroscopy (FTIR). Kinetics data were best fitted to a pseudo-second-order model. Equilibrium data were better described by the Temkin isotherm model with a multilayer adsorption capacity. The study showed that leaves of cola nut are a promising biosorbent for Cd2+ and Cr6+ which could be utilized for industrial wastewater remediation.

Kinetic and thermodynamic studies on biosorption of Cr(VI) on raw and chemically modified Datura stramonium fruit

Biosorption of Cr(VI) on sulfuric and phosphoric acid-treated Datura stramonium fruit was investigated in batch mode. The various parameters that influence the biosorption process such as Cr(VI) initial concentration, biosorbent dosage, contact time, temperature, and pH value were optimized. Both linear and non-linear regression analysis of isotherm data suggest that Langmuir isotherm model mimics the behavior of Cr(VI) ion biosorption onto Datura stramonium fruit biosorbent. The maximum Cr(VI) ions adsorption capacity of 138.074 mg/g at pH 2 is achieved with phosphoric acid treated Datura stramonium (PDSF). The kinetics of adsorption process is well described by pseudo-second-order model with high R² and low χ² value. The estimated activation energy of < 8 kJ/mol obtained for both raw and chemically modified adsorbents suggests that the adsorption occurs mainly via physisorption. Besides, thermodynamic results reveal that biosorption of Cr(VI) on both treated and untreated Datura stramonium was endothermic, spontaneous, and randomness in nature.

Batch Study of Cadmium Biosorption by Carbon Dioxide Enriched Aphanothece sp. Dried Biomass

The conventional method for cadmium removal in aqueous solutions (1–100 mg/L) is ineffective and inefficient. Therefore, a batch biosorption reactor using a local freshwater microalga (originating from an urban lake, namely, Situ Rawa Kalong-Depok) as dried biosorbent was tested. Biosorbent made from three kinds of cyanobacterium Aphanothece sp. cultivars (A0, A8, and A15) were used to eliminate cadmium (Cd2+) ions in aqueous solution (1–7 mg/L). The biosorbents were harvested from a photobioreactor system enriched with carbon dioxide gas of 0.04% (atmospheric), 8%, and 15% under continuous light illumination of about 5700–6000 lux for 14 d of cultivation. Produced dried biosorbents had Brunauer–Emmet–Teller (BET) surface area ranges of 0.571–1.846 m2/g. Biosorption of Cd2+ was pH and concentration dependent. Sorption was spontaneous (ΔG = −8.39 to −10.88 kJ/mol), exothermic (ΔH = −41.85 to −49.16 kJ/mol), and decreased randomness (ΔS = −0.102 to −0.126 kJ/mol. K) on the interface between solid and liquid phases when the process was completed. The kinetic sorption data fitted best to the pseudo-second-order model (k2 = 2.79 × 10−2, 3.96 × 10−2, and 4.54 × 10−2 g/mg.min). The dried biosorbents of A0, A8, and A15, after modeling with the Langmuir and Dubinin–Radushkevich isotherm models, indicated that cadmium binding occurred through chemisorption (qmax, D-R = 9.74 × 10−4, 4.79 × 10−3, and 9.12 × 10−3 mol/g and mean free energy of 8.45, 11.18, and 11.18 kJ/mol) on the monolayer and homogenous surface (qmax, Langmuir of 12.24, 36.90, and 60.24 mg/g). In addition, the results of SEM, EDX, and FTIR showed that there were at least nine functional groups that interacted with Cd2+ (led to bond formation) after biosorption through cation exchange mechanisms, and morphologically the surfaces changed after biosorption. Biosorbent A15 indicated the best resilient features over three cycles of sorption–desorption using 1 M HCl as the desorbing eluent. These biosorbents can be a potent and eco-friendly material for treating aqueous wastewater.

Removal of heavy metals in aquatic environment by graphene oxide composites: a review

As the most important graphene derivate, graphene oxide (GO) is a high-efficient adsorbent for the removal of heavy metals in aquatic environment due to its abundant oxygen functional groups, enormous specific area, and strong hydrophilia. However, there are some drawbacks, such as easily aggregating and difficult separation, restricting the environmental application of GO. GO is not a suitable adsorbent by itself. Hence, some materials were used to synthesize GO composites, and GO composites are commonly characterized by high adsorption capacity to overcome the above drawbacks. This review discusses five main GO composites-GO-chitosan, GO-alginate, GO-SiO₂, NZVI-rGO, and magnetic GO composites-and summarizes the synthesis methods of GO composites and its application for the removal of heavy metals in aquatic environments. The influencing factors, adsorption capacities, and mechanisms related to the removal of heavy metals by GO composites are highlighted. Lastly, the application potentials and challenges of GO composites for aqueous environmental remediation are discussed. Graphical abstract.

Bioremediation Options for Heavy Metal Pollution

BACKGROUND

Rapid industrialization and anthropogenic activities such as the unmanaged use of agro-chemicals, fossil fuel burning and dumping of sewage sludge have caused soils and waterways to be severely contaminated with heavy metals. Heavy metals are non-biodegradable and persist in the environment. Hence, remediation is required to avoid heavy metal leaching or mobilization into environmental segments and to facilitate their extraction.

OBJECTIVES

The present work briefly outlines the environmental occurrence of heavy metals and strategies for using microorganisms for bioremediation processes as reported in the scientific literature.

METHODS

Databases were searched from different libraries, including Google Scholar, Medline and Scopus. Observations across studies were then compared with the standards for discharge of environmental pollutants.

DISCUSSION

Bioremediation employs microorganisms for removing heavy metals. Microorganisms have adopted different mechanisms for bioremediation. These mechanisms are unique in their specific requirements, advantages, and disadvantages, the success of which depends chiefly upon the kind of organisms and the contaminants involved in the process.

CONCLUSIONS

Heavy metal pollution creates environmental stress for human beings, plants, animals and other organisms. A complete understanding of the process and various alternatives for remediation at different steps is needed to ensure effective and economic processes.

COMPETING INTERESTS

The authors declare no competing financial interests.

Adsorption of Lead on Lentil Husk in Fixed Bed Column Bioreactor

This study depicts successful employment of fixed bed column bioreactor for adsorption of lead in continuous mode using lentil husk as sorbent. Design parameters considerably controlled the reactor performance, amongst which height of the fixed bed and flow rate were crucial in generating cleaner effluent. Adsorption capacity was found to shoot up to the level of 205.87 mg g^-1 at 10 cm bed height, 100 mg L^-1 feed concentration and 20 mL min^-1 flow rate. Kinetic study done at regular intervals of time revealed high percentage removal of lead (99-96%) throughout entire span of reactor operation. Experimental data were well interpreted by Thomas model and Yoon-Nelson model. The reactor bed was regenerated after each adsorption and loaded metal was recovered up to the extent of ∼96%. The column reactor was efficient enough to treat lead containing actual industrial effluents.

Effects of Pretreatment Methods of Wheat Straw on Adsorption of Cd(II) from Waterlogged Paddy Soil

Two types of pretreatment categories, namely microwave-assisted alkalization and microwave-assisted acid oxidation, were used to synthesize novel wheat straw adsorbents for the effective removal of Cd(II) in simulated waterlogged paddy soil. A systematic adsorption behavior study, including adsorption kinetics and adsorption isotherms was conducted. Results showed that wheat straw pretreated by microwave-assisted soaking of NaOH and ethanol solution obtained the highest Cd(II) removal efficiency of 96.4% at a reaction temperature of 25 ℃, pH of 7.0, initial Cd(II) concentration of 50 mg/L, and adsorbent/adsorbate ratio of 10 g/L. Sequential extraction experiment was carried out to analyze the changes of different of Cd(II) in soil, the aim of which was to study the mobility of Cd(II) and then evaluate the toxicity that Cd(II) might bring to plants. A 60-day incubation was performed to investigate the dynamic variations of soil pH and dissolved organic carbon content over incubation time. Characterization analyses revealed the morphological changes of wheat straw adsorbents, which suggested that those pretreatment methods were of significance. This study provided an environmentally friendly way to reuse agricultural wastes and remedy Cd(II) contaminated soil.

Advances in cultivation, wastewater treatment application, bioactive components of Caulerpa lentillifera and their biotechnological applications

The edible seaweed Caulerpa lentillifera, a powerful natural food source that is rich in protein, minerals, dietary fibers, vitamins, saturated fatty acids and unsaturated fatty acids, has been mass cultured in some Asian countries and has been the focus of researchers in recent years. Here, the operational conditions of its culture, application in wastewater treatment, and bioactive components are summarized and comparatively analyzed. Based on previous studies, salinity, nutrient concentrations, irradiance and temperature are stress factors for algal growth. Moreover, dried Caulerpa lentillifera seaweed is efficient in the biosorption of heavy metals and cationic dyes in wastewater, and fresh seaweed can be introduced as a biofilter in aquaculture system treatment. In addition, among the rich bioactive compounds in Caulerpa lentillifera, the phenolic compounds show the potential ability for regulating glucose metabolism in vivo. Polysaccharides and oligosaccharides exhibit anticoagulant, immunomodulatory effects and cancer-preventing activity. Siphonaxanthin is a compound with attractive novel functions in cancer-preventing activity and lipogenesis-inhibiting effects. Furthermore, the antioxidant activity of siphonaxanthin extracted from Caulerpa lentillifera could be stronger than that of astaxanthin. This review offers an overview of studies of Caulerpa lentillifera addressing various aspects including cultivation, wastewater treatment and biological active components which may provide valuable information for the cultivation and utilization of this green alga.

Response mechanism of mine-isolated fungus Aspergillus niger IOC 4687 to copper stress determined by proteomics

Proteomic analysis of the fungus Aspergillus niger showed that its capacity to absorb metals was boosted by physiological modification under metal stress conditions.

Adsorption of heavy metals on conventional and nanostructured materials for wastewater treatment purposes: A review

The problem of water pollution is of a great concern. Adsorption is one of the most efficient techniques for removing noxious heavy metals from the solvent phase. This paper presents a detailed information and review on the adsorption of noxious heavy metal ions from wastewater effluents using various adsorbents - i.e., conventional (activated carbons, zeolites, clays, biosorbents, and industrial by-products) and nanostructured (fullerenes, carbon nanotubes, graphenes). In addition to this, the efficiency of developed materials for adsorption of the heavy metals is discussed in detail along with the comparison of their maximum adsorption capacity in tabular form. A special focus is made on the perspectives of further wider applications of nanostructured adsorbents (especially, carbon nanotubes and graphenes) in wastewater treatment.

Adsorption and Desorption Characteristics of Cd2+ and Pb2+ by Micro and Nano-sized Biogenic CaCO3

The purpose of this study was to elucidate the characteristics and mechanisms of adsorption and desorption for heavy metals by micro and nano-sized biogenic CaCO3 induced by Bacillus subtilis, and the pH effect on adsorption was investigated. The results showed that the adsorption characteristics of Cd2+ and Pb2+ are well described by the Langmuir adsorption isothermal equation, and the maximum adsorption amounts for Cd2+ and Pb2+ were 94.340 and 416.667 mg/g, respectively. The maximum removal efficiencies were 97% for Cd2+, 100% for Pb2+, and the desorption rate was smaller than 3%. Further experiments revealed that the biogenic CaCO3 could maintain its high adsorption capability for heavy metals within wide pH ranges (3-8). The FTIR and XRD results showed that, after the biogenic CaCO3 adsorbed Cd2+ or Pb2+, it did not produce a new phase, which indicated that biogenic CaCO3 and heavy metal ions were governed by a physical adsorption process, and the high adsorptive capacity of biogenic CaCO3 for Cd2+ and Pb2+ were mainly attributed to its large total specific surface area. The findings could improve the state of knowledge about biogenic CaCO3 formation in the environment and its potential roles in the biogeochemical cycles of heavy metals.

Heavy metal detoxification by recombinant ferritin from Apostichopus japonicus

Ferritin fromApostichopus japonicasshowed better ability in heavy metal detoxification than horse spleen ferritin.

Competitive adsorption of phthalate esters on marine surface sediments: kinetic, thermodynamic, and environmental considerations

In this study, the sorption behavior of six widely used phthalate esters (PEs) on marine sediments was investigated. The adsorption of PEs was fast and reached the equilibrium within 6 h. The forward and backward rate constants of all PEs on sediments were calculated. Several kinds of kinetic and thermodynamic models have been investigated; the pseudo-second-order model and the partition isotherm model were best fitted to the adsorption behavior of PEs. The rate-limiting step of sorption was controlled by the film diffusion mechanism. After treating sediments with H₂O₂, the partition coefficients of all PEs were significantly reduced and indicated that the amorphous organic carbon has a major role in adsorption process. The negative values of ΔH° and ΔG° for these compounds showed that the sorption process is exothermic and spontaneous. The adsorption capacities of all PEs were slightly influenced by increasing the salinity from 0 to 40 g L^-1. These research findings have a prime importance on assessment of the fate and transport of PEs in seawater-sediment systems.