Influence of fatty acid composition of raw materials on biodiesel properties

One-pot bioconversion of fungal lipid to mycodiesel: a sustainable approach

The conversion of filamentous fungus-based feedstock into Biodiesel holds potential as a sustainable and eco-conscious method for producing alternative liquid fuels. This study examined the comparison of individual Fatty Acid Methyl Esters (FAME) of Aspergillus niger and Curvularia lunata with the consortium of both filamentous fungal cocktail Fatty acid methyl esters (cFAME), following a transesterification process that turned the fungal lipids into myco-based biodiesel productions. cFAME weighs 23.89 g and accumulates to 20.43 g of lipid yield, with 86% of cellular lipids; in contrast, A. niger weighs 12.65 g and pile up 9.5 g of lipid yield, with 75% of cellular lipid, also C. lunata exhibits 8.35 g of dry weight with 4.89 g of lipid concentration, with 59% of cellular lipids. A. niger was known to contain C16-C18 saturated and unsaturated fatty acids possess LAME (C18:2), OAFA (C18:1), and PAME (C16:0) were shown in high percentages accounted for 86.6% in A. niger. The results showed that PUFA was predominant over MUFA and SFA. C. lunata chiefly produces C16 and C18 fatty acids, which are considered favorable for combustion properties with oleic acid (C18:1), linoleic acid (C18:2), palmitic acid (C16:0), and stearic acid (C18:0), on the comparison. However, the FAME profile of C. lunata occupies only 39.07% of the biodiesel quality. Pentadecanoic acid, palmitic acid, palmitoleic acid, Oleic acid, Linolenic acid, Linoleic acis, and Hexanoic acid with the carbon range of C6:0 - C18:3 were observed in cFAME. Based on the biodiesel yield, cFAME scored 20.55%, whereas A. niger with 11.05 and C.lunata 2.45%, respectively. The presence of methyl esters containing various long-chain fatty acids indicates very effective biodiesel assets, as confirmed by GC-MS analysis, which evidenced ignition efficiency, among others. cFAMEs were impacted by high ignition efficiency with > 4 min. Consortium strategies seize attention in different dimensions and have been confirmed by their upregulation in their fatty acid profiles; in the future, the combination of high lipid holders among the fungal kingdom can be an alternative in myco-based biodiesel production.

Maximizing lipid accumulation in Tetradesmus obliquus under heavy metal stress for sustainable biodiesel innovation

This study investigates the potential of Tetradesmus obliquus for lipid accumulation under heavy metal stress and evaluates it's aviability for biodiesel production. We surveyed how different concentrations of heavy metals, including manganese (Mn), cobalt (Co), and zinc (Zn), influence the carbohydrate & protein, lipid yield, and fatty acid profiles of T. obliquus cultures. Our results demonstrated that while lipid content increased under heavy metal stress, the extent of accumulation was highly dependent on metal type and concentration. Notably, the algal culture treated with 0.04 mM Co²⁺ showed the highest lipid accumulation. Treatment with 0.3 mM Zn²⁺ resulted in the highest proportion of saturated fatty acids (SFA). The Relative Enrichment Efficiency Coefficient (REEC) analysis demonstrated that 0.04 mM and 0.07 mM Co²⁺ led to the highest lipid and carbohydrate content stimulation. Additionally, GC-MS analysis revealed increased monounsaturated fatty acids (MUFA) under several metal stress conditions. The study demonstrated that exposure to specific concentrations of heavy metals can significantly enhance lipid accumulation and alter the fatty acid profiles of T. obliquus, which are crucial for improving biodiesel quality. The implications of these findings suggest that heavy metal-induced stress could be a feasible approach to enhancing lipid accumulation for sustainable biodiesel production, and T.obliquus is a promising candidate for future biodiesel production.

Integrated biorefinery approach for sustainable production of biodiesel, bioplastics and high value bioproducts from a bloom forming alga, Botryococcus braunii

The global shift towards sustainable energy and bioproducts has intensified research on algae. Renewable green biofuel can address and provide solutions to both energy crisis and climate change challenges. Botryococcus braunii, a bloom forming green microalga, known for its high lipid content and potential for biofuel production has been explored in the present study. The study envisages the utilisation of algal blooms in freshwater ecosystems for the production of biodiesel and high value bioproducts through an integrated biorefinery approach. During the peak bloom, the algal cell densities reached up to 3.3 × 106 colonies L-1 with significant shift in water quality due to high nutrient uptake. Gas chromatography-mass spectroscopic analysis revealed high concentration of saturated and monounsaturated fatty acids, particularly hexadecanoic acid (C16:0) and 9-octadecenoic acid (C18:1) which are essential for stable, energy-rich biodiesel production. Hydrocarbons including squalene, botryococcenes, and botryococcane, produced by this alga have significant industrial applications. The high polyhydroxybutyrate (PHB) content in the alga emphasises its potential for sustainable bioplastic production. Growth conditions, lipid content, and biochemical composition of B. braunii were investigated. Algal blooms can provide a sustainable and economically viable source of biofuel with high value co-products. This approach not only contributes to renewable energy solutions through valorising a waste bioresource but in combination with other mass cultivation strategies can also offer a means to sustainably manage the impact of algal blooms on aquatic ecosystems.

A polyphasic approach in the identification and biochemical characterization of Dunaliella tertiolecta with biodiesel potential from a saltern in Mauritius

Bioprospecting robust and oleaginous strain is crucial for the commercialization of microalgae-based biodiesel. In this study, a microalgal strain SCH18 was isolated from a solar saltern located in Mauritius. This isolate was identified as Dunaliella tertiolecta based on a polyphasic approach that combined molecular, physiological, and morphological analyses. Furthermore, the effect of different salinities on the biochemical composition and fatty acid profile of this microalga was investigated to explore its potential in producing biodiesel. Results from the growth studies showed that salinity of 1.0 M NaCl was optimal for achieving a high growth rate. Under this salt concentration, the growth rate and the doubling time were calculated as 0.39 ± 0.003 day-1 and 1.79 ± 0.01 days, respectively. In terms of biochemical composition, a substantial amount of carbohydrate (42.02 ± 5.20%), moderate amount of protein (30.35 ± 0.18%) and a low lipid content (17.81 ± 2.4%) were obtained under optimal NaCl concentration. The fatty acid analysis indicated the presence of palmitic acid, stearic acid, palmitoleic acid, oleic acid, linoleic acid, gamma, and alpha-linolenic acids, which are suitable for biodiesel synthesis. The predicted biodiesel properties were in accordance with the standard of ASTM 6751, indicating that the microalgal isolate D. tertiolecta SCH18 is a potential candidate for use in biodiesel production.

Impact of annealing and incorporation of vegetable oils on physicochemical and rheological properties of wheat starch

This study investigated the impact of annealing treatment and lipids (vegetable oils, such as palm, olive, and grapeseed oils) on the physicochemical and rheological properties of wheat starch. Annealing of wheat starch (WSANN45, WSANN55) under different temperatures (45 °C and 55 °C) and with added vegetable oil (WS-OilANN45, WS-OilANN55) were compared with untreated wheat starch (WS). Annealing at 45 °C resulted in slight changes in the physicochemical properties of starch. However, annealing at 55 °C significantly decreased the relative crystallinity, pasting viscosity, and swelling power. WS-OilANN45 showed a higher ΔH (dissociation peak) than WSANN45, indicating successful lipid incorporation, whereas WS-OilANN55 showed no significant difference from WSANN55, suggesting that lipid integration was not achieved. Rheological tests showed that WS-OilANN45 slightly reduced the shear-thinning behavior and viscoelastic properties of starch. The introduction of oils affected the swelling and pasting properties, weakened the gel network, and significantly reduced the gel hardness. This approach offers a potential method that uses food-grade oils and annealing to modify starch and alter its rheological and physical properties while retaining its native granular characteristics.

Improving the biodiesel production in the marine diatom Thalassiosira pseudonana cultivated in nutrient deficiency and sewage water

The use of microalgae as a feedstock in biofuel production is highly encouraging. The marine diatom in this study, Thalassiosira pseudonana, was used as a test organism to evaluate the impact of nitrogen or phosphorus limitation and sewage water on improving biodiesel production. The growth rate is more affected in cultures without phosphorus by 41.8% lower than in control and the highest dry weight estimated in control. The cellular dry weight significantly increased in cultures treated with mix1 and mix2 wastewater compared to the control cultures. Chlorophyll a content decreased in the absence of nitrogen and phosphorous and in sewage water cultures. Lipid content in algal cultures without nitrogen or phosphorus and in sewage water accumulated nearly twice as much lipid content in synthetic medium. T. pseudonana showed high FAME contents; the two most abundant fatty acids, stearic acid (C18:0) and palmitoleic acid (C16:1), in the algal extracts revealed that T. pseudonana was predominantly composed of these fatty acids. T. pseudonana grown in nitrogen or phosphorus-deficient conditions exhibited an extreme percentage of saturated fatty acids (SFAs) by 87.38% and 85.47%, respectively, of the total fatty acids (TFAs). More importantly, the low polyunsaturated fatty acid content in oils indicates a high cetane number, low iodine value, and low corrosion for biodiesel quality indicators. Producing biodiesel that closely meets worldwide biodiesel requirements (ASTM D6751 and EN 14214) is the goal of this work, which shows that growing T. pseudonana under nutrient limitations leads to algal metabolism in that direction.

Enhancing biomass, hydrocarbon and biodiesel properties of green microalga Botryococcus braunii KMITL through gamma and UV radiation exposure

This study investigated the effects of gamma (137Cs, 0-250 Gy) and UV (UV-C, 0-12 h) radiation on growth and biodiesel properties of Botryococcus braunii KMITL. For gamma radiation, maximum biomass (1.37 ± 0.02 g L-1) was achieved with 50 Gy, while a dose of 200 Gy resulted in the highest hydrocarbon content (51.84 ± 0.20%) and yield (0.66 ± 0.01 g L-1). For UV radiation, a 9 h exposure produced the highest biomass (2.45 ± 0.05 g L-1), hydrocarbon content (55.01 ± 1.22%), and yield (1.35 ± 0.04 g L-1). Algae exposed to gamma radiation within the range of 0-150 Gy exhibited C16:0 as the dominant fatty acid methyl ester (FAME), similar to those exposed to UV radiation, while algae exposed to 200-250 Gy displayed C18:1n9t as the dominant FAME. High levels of gamma and UV radiation were observed to lengthen fatty acid chains and increase unsaturated fatty acids. The cetane values of biodiesel from algae exposed to gamma and UV radiation ranged from 64.55 ± 0.14-66.47 ± 0.20 and 59.43 ± 0.04-65.27 ± 0.22, respectively, all meeting standard criteria. Both gamma and UV radiation also improved the saponification value and cold flow properties of the biodiesel. These findings suggest that controlled levels of gamma and UV radiation effectively enhance hydrocarbon yields with significant implications for biofuel production.

Pollution control and biodiesel production with microalgae: new perspectives on the use of flat panel photobioreactors regarding variation in volume application rate

In the present study, the microalga Arthrospira platensis DHR 20 was cultivated in vertical flat-plate photobioreactors (FPBRs) to bioremediate anaerobically digested cattle wastewater (ACWW) and used as a growth substrate. The final objective was to evaluate the properties of the oil extracted from this biomass to determine its potential for biodiesel production. The process was divided into five phases, varying the volume of the applied substrate: 1 L (Phase I), 5 L (Phase II), 10 L (Phase III), 15 L (Phase IV), and 20 L (Phase V). Dry biomass reached a maximum of 5.7 g L-1, and productivity peaked at 0.74 g L-1d-1. The highest rate of CO2 biofixation was 1213.5 mg L-1 day-1, showing good potential for purifying the air. The highest specific maximum growth rate (μmax) and the shortest doubling time (Dt) were found during Phase I. The removal of pollutants and nutrients during the experimental phases ranged from 65.8% to 87.1% for chemical oxygen demand (COD), 82.2% to 85.8% for total organic carbon (TOC), 91% to 99% for phosphate (PO43-), 62.5% to 93% for nitrate (NO3-), 90.4% to 99.7% for ammoniacal nitrogen (NH4+), and 86.5% to 98.5% for total nitrogen (TN). The highest lipid production recorded was 0.172 g L-1 day-1. The average cetane number recorded in Phase IV of 51 suggests that the fuel will ignite efficiently and consistently, providing smooth operation and potentially reducing pollutant emissions. The analysis of fatty acids revealed that the produced biodiesel has the potential to be used as an additive for other low-explosive biocombustibles, representing an innovative and sustainable approach that simultaneously offers bioremediation and carbon sequestration.

Isolation and identification of a salt-tolerant Coelastrum sp. and exploration of its potential for biodiesel production

Given the escalating demand for renewable biofuels amidst the continual consumption of fossil energy, the exploration and identification of microalgal strains for biodiesel production have become crucial. In this study, a microalgal strain named HDMA-12 was isolated from Lake Chenjiadayuan in China to evaluate its biodiesel potential. Phylogenetic analysis of its internal transcribed spacer sequences revealed HDMA-12 as a new molecular record in the genus Coelastrum. When cultivated in BG11 basal medium, HDMA-12 achieved a biomass of 635.7 mg L-1 and a lipid content of 26.4%. Furthermore, the fatty acid methyl ester profile of HDMA-12 exhibited favorable combustion characteristics. Subjected to 200 mM NaCl stress, HDMA-12 reached its maximum biomass of 751.5 mg L-1 and a lipid content of 28.9%. These findings indicate the promising prospects of HDMA-12 as a promising microalgal strain for further advancements in biodiesel production.

Effects of altering the ratio of C16:0 and cis-9 C18:1 in rumen bypass fat on growth performance, lipid metabolism, intestinal barrier, cecal microbiota, and inflammation in fattening bulls

BACKGROUND

C16:0 and cis-9 C18:1 may have different effects on animal growth and health due to unique metabolism in vivo. This study was investigated to explore the different effects of altering the ratio of C16:0 and cis-9 C18:1 in fat supplements on growth performance, lipid metabolism, intestinal barrier, cecal microbiota, and inflammation in fattening bulls. Thirty finishing Angus bulls (626 ± 69 kg, 21 ± 0.5 months) were divided into 3 treatments according to the randomized block design: (1) control diet without additional fat (CON), (2) CON + 2.5% palmitic acid calcium salt (PA, 90% C16:0), and (3) CON + 2.5% mixed fatty acid calcium salt (MA, 60% C16:0 + 30% cis-9 C18:1). The experiment lasted for 104 d, after which all the bulls were slaughtered and sampled for analysis.

RESULTS

MA tended to reduce 0-52 d dry matter intake compared to PA (DMI, P = 0.052). Compared with CON and MA, PA significantly increased 0-52 d average daily gain (ADG, P = 0.027). PA tended to improve the 0-52 d feed conversion rate compared with CON (FCR, P = 0.088). Both PA and MA had no significant effect on 52-104 days of DMI, ADG and FCR (P > 0.05). PA tended to improve plasma triglycerides compared with MA (P = 0.077), significantly increased plasma cholesterol (P = 0.002) and tended to improve subcutaneous adipose weight (P = 0.066) when compared with CON and MA. Both PA and MA increased visceral adipose weight compared with CON (P = 0.021). Only PA increased the colonization of Rikenellaceae, Ruminococcus and Proteobacteria in the cecum, and MA increased Akkermansia abundance (P < 0.05). Compared with CON, both PA and MA down-regulated the mRNA expression of Claudin-1 in the jejunum (P < 0.001), increased plasma diamine oxidase (DAO, P < 0.001) and lipopolysaccharide (LPS, P = 0.045). Compared with CON and MA, PA down-regulated the ZO-1 in the jejunum (P < 0.001) and increased plasma LPS-binding protein (LBP, P < 0.001). Compared with CON, only PA down-regulated the Occludin in the jejunum (P = 0.013). Compared with CON, PA and MA significantly up-regulated the expression of TLR-4 and NF-κB in the visceral adipose (P < 0.001) and increased plasma IL-6 (P < 0.001). Compared with CON, only PA up-regulated the TNF-α in the visceral adipose (P = 0.01). Compared with CON and MA, PA up-regulated IL-6 in the visceral adipose (P < 0.001), increased plasma TNF-α (P < 0.001), and reduced the IgG content in plasma (P = 0.035). Compared with CON, PA and MA increased C16:0 in subcutaneous fat and longissimus dorsi muscle (P < 0.05), while more C16:0 was also deposited by extension and desaturation into C18:0 and cis-9 C18:1. However, neither PA nor MA affected the content of cis-9 C18:1 in longissimus dorsi muscle compared with CON (P > 0.05).

CONCLUSIONS

MA containing 30% cis-9 C18:1 reduced the risk of high C16:0 dietary fat induced subcutaneous fat obesity, adipose tissue and systemic low-grade inflammation by accelerating fatty acid oxidative utilization, improving colonization of Akkermansia, reducing intestinal barrier damage, and down-regulating NF-κB activation.

Low-dose ionizing radiation generates a hormetic response to modify lipid metabolism in Chlorella sorokiniana

Algal biomass is a viable source of chemicals and metabolites for various energy, nutritional, medicinal and agricultural uses. While stresses have commonly been used to induce metabolite accumulation in microalgae in attempts to enhance high-value product yields, this is often very detrimental to growth. Therefore, understanding how to modify metabolism without deleterious consequences is highly beneficial. We demonstrate that low-doses (1-5 Gy) of ionizing radiation in the X-ray range induces a non-toxic, hormetic response in microalgae to promote metabolic activation. We identify specific radiation exposure parameters that give reproducible metabolic responses in Chlorella sorokiniana caused by transcriptional changes. This includes up-regulation of >30 lipid metabolism genes, such as genes encoding an acetyl-CoA carboxylase subunit, phosphatidic acid phosphatase, lysophosphatidic acid acyltransferase, and diacylglycerol acyltransferase. The outcome is an increased lipid yield in stationary phase cultures by 25% in just 24 hours, without any negative effects on cell viability or biomass.

Advanced wastewater treatment with microalgae-indigenous bacterial interactions

Microalgal-indigenous bacterial wastewater treatment (MBWT) emerges as a promising approach for the concurrent removal of nitrogen (N) and phosphorus (P). Despite its potential, the prevalent use of MBWT in batch systems limits its broader application. Furthermore, the success of MBWT critically depends on the stable self-adaptation and synergistic interactions between microalgae and indigenous bacteria, yet the underlying biological mechanisms are not fully understood. Here we explore the viability and microbial dynamics of a continuous flow microalgae-indigenous bacteria advanced wastewater treatment system (CFMBAWTS) in processing actual secondary effluent, with a focus on varying hydraulic retention times (HRTs). The research highlights a stable, mutually beneficial relationship between indigenous bacteria and microalgae. Microalgae and indigenous bacteria can create an optimal environment for each other by providing essential cofactors (like iron, vitamins, and indole-3-acetic acid), oxygen, dissolved organic matter, and tryptophan. This collaboration leads to effective microbial growth, enhanced N and P removal, and energy generation. The study also uncovers crucial metabolic pathways, functional genes, and patterns of microbial succession. Significantly, the effluent NH4+-N and P levels complied with the Chinese national Class-II, Class-V, Class-IA, and Class-IB wastewater discharge standards when the HRT was reduced from 15 to 6 h. Optimal results, including the highest rates of CO2 fixation (1.23 g L-1), total energy yield (32.35 kJ L-1), and the maximal lipid (33.91%) and carbohydrate (41.91%) content, were observed at an HRT of 15 h. Overall, this study not only confirms the feasibility of CFMBAWTS but also lays a crucial foundation for enhancing our understanding of this technology and propelling its practical application in wastewater treatment plants.

Morpho-Physiological Traits and Oil Quality in Drought-Tolerant Raphanus sativus L. Used for Biofuel Production

Raphanus sativus L. is a potential source of raw material for biodiesel fuel due to the high oil content in its grains. In Brazil, this species is cultivated in the low rainfall off-season, which limits the productivity of the crop. The present study investigated the effects of water restriction on the physiological and biochemical responses, production components, and oil quality of R. sativus at different development stages. The treatments consisted of 100% water replacement (control), 66%, and 33% of field capacity during the phenological stages of vegetative growth, flowering, and grain filling. We evaluated characteristics of water relations, gas exchange, chlorophyll a fluorescence, chloroplast pigment, proline, and sugar content. The production components and chemical properties of the oil were also determined at the end of the harvest cycle. Drought tolerance of R. sativus was found to be mediated primarily during the vegetative growth stage by changes in photosynthetic metabolism, stability of photochemical efficiency, increased proline concentrations, and maintenance of tissue hydration. Grain filling was most sensitive to water limitation and showed a reduction in yield and oil content. However, the chemical composition of the oil was not altered by the water deficit. Our data suggest that R. sativus is a drought-tolerant species.

Determination of Triacylglycerol Composition in Mealworm Oil (Tenebrio molitor) via Electrospray Ionization Tandem Mass Spectrometry with Multiple Neutral Loss Scans

Mealworms (Tenebrio molitor) have been used as an alternative source of proteins and lipids. Triacylglycerols (TAGs) are major sources of energy and have been used to provide essential fatty acids. They are also the main components of mealworm oil, and their composition and content are extensively linked to its physical and chemical properties. However, because of the complexity of TAG molecules, their identification and quantitation are challenging. This study employed electrospray ionization tandem mass spectrometry (ESI-MS/MS) with multiple neutral loss scans (NLS) to analyze the TAG composition and content in mealworm oil. Identifying and quantifying TAGs using ESI-MS/MS in combination with multiple NLS was an efficient way to improve accuracy and timeliness. For the accurate quantification of TAGs, isotopic deconvolution and correlation factors were applied. A total of 57 TAGs were identified and quantified: C52:2 (16:0/18:1/18:1) (1549.4 nmol/g, 18.20%), C52:3 (16:0/18:1/18:2) (1488.1 nmol/g, 17.48%), C54:4 (18:1/18:1/18:2) (870.1 nmol/g, 10.23%), C54:6 (18:1/18:2/18:2) (659.8 nmol/g, 7.76%) and C52:4 (16:0/18:2/18:2) (600.5 nmol/g, 7.06%), which were the most abundant TAGs present in the mealworm oil. The fundamental properties of mealworm oil, including its degree of oxidation, nutritional effect and physical properties, were elucidated.

Growth, nutrient removal, and lipid productivity promotion of Chlorella sorokiniana by phosphate solubilizing bacteria Bacillus megatherium in swine wastewater: Performances and mechanisms

Effects of a phosphorus-solubilizing bacteria (PSB) Bacillus megatherium on growth and lipid production of Chlorella sorokiniana were investigated in synthesized swine wastewater with dissolved inorganic phosphorus (DIP), insoluble inorganic phosphorus (IIP), and organic phosphorus (OP). The results showed that the PSB significantly promoted the algal growth in OP and IIP, by 1.10 and 1.78-fold, respectively. The algal lipid accumulation was also greatly triggered, respectively by 4.39, 1.68, and 1.38-fold in DIP, IIP, and OP. Moreover, compared with DIP, OP improved the oxidation stability of algal lipid by increasing the proportion of saturated fatty acids (43.8 % vs 27.9 %), while the PSB tended to adjust it to moderate ranges (30.2-41.6 %). Further, the transcriptome analysis verified the OP and/or PSB-induced up-regulated genes involving photosynthesis, lipid metabolism, signal transduction, etc. This study provided novel insights to enhance microalgae-based nutrient removal combined with biofuel production in practical wastewater, especially with complex forms of phosphorus.

Enhancing the biodiesel production in the green alga Chlorella vulgaris by heavy metal stress and prediction of fuel properties from fatty acid profiles

The green microalga Chlorella vulgaris was used as a test organism during this study for evaluation of the impact of different heavy metal stress, Mn2+, Co2+, and Zn2+, on enhancing the biodiesel production. The algal cultures were grown for 13 days under heavy metal stress after which were subjected to estimation of growth, some primary metabolites, lipid, and fatty acid profiles. The maximum lipid accumulation (283.30 mg/g CDW) was recorded in the algal culture treated with 3 µM cobalt nitrate. Application of 2 mM manganese chloride; 1, 2, and 3 μM cobalt nitrate; and 0.2, 0.4, and 0.6 mM zinc sulfate caused highly significant increases in the lipid contents amounting to 183.8, 191.4, 230.6, 283.3, 176.3, 226.0, and 212.1 mg/g CDW, respectively, in comparison to control (153.4 mg/g CDW). The maximum proportion of saturated fatty acids (SFA) (64.44%) was noted in the culture treated with 6 mM MnCl2 due to the existence of palmitic acid (C16:0), stearic acid (C18:0), and pentadecylic acid (C15:0) which are represented by 53.59%, 5.96%, and 1.37%, respectively, of the total FAs. Relative increase in energy compound (REEC) showed that 1, 2, and 3 µM Co2+ lead to the highest stimulation in lipid and carbohydrate contents to 0.207, 0.352, and 0.329 × 103%, respectively. Empirical formulas were used for the assessment of biodiesel fuel properties based on FAME composition. The estimated properties met the prescribed international standard criteria.

Biodiesel production and exploring properties of Datura stramonium L. oil with its optimization using combined approaches-Taguchi, grey relational analysis, and response surface methodology

Biodiesel production through the synthesis of Datura stramonium L. oil is studied to explore the most efficient approaches to suggest an alternate feedstock for biodiesel production. The main objective of this work is to optimize the process variables of biodiesel synthesis by using some statistical approach (Taguchi method, grey relational analysis (GRA), and response surface methodology (RSM) analyzing three parameters, i.e., alcohol-to-oil molar ratio, catalyst (NaOH) concentration, and process temperature for achieving maximum biodiesel derived from Datura stramonium L. oil. The transesterification process is applied by using an ultrasonic-assisted technique. Grey relational analysis (GRA) was successfully applied with the Taguchi method resulting in the optimum combination of A2B1C1. Based on the findings, the best operating conditions for transesterifying are attained with the RSM approach consisting of a 5.697:1 molar ratio (level 2), 0.3 (wt.%) NaOH concentration (level 1), and 70 °C process temperature (level 1). With a value of 87.02%, these ideal operating conditions produce the maximum yield as compared to grey relational analysis (GRA) yields 83.99%. The obtained results have been verified through the characterization of oil and biodiesel as well. Also, the fuel qualities of DSL biodiesel were identified and assessed. DSL oil was found 137.6 degrees of unsaturation during fatty acid profile analysis. DSL biodiesel was found the best kinematic viscosity (4.2 mm2/s) and acid value (0.49) when compared to Karanja and palm biodiesel. D. stramonium L. was recognized as a suitable species for biodiesel feedstock according to the findings.

Molecular phylogenetics of the Umbelopsis genus-identification of new species and evaluation of their oil application value

AIMS

The aim of this study was to reconstruct the evolutionary framework of the genus Umbelopsis by using modern taxonomic strategies and evaluating the quality of oil and prospective uses of three distinct species.

METHODS AND RESULTS

Three species of Umbelopsis were identified based on morphological characteristics and phylogenetic evidence obtained from three genes (ITS, LSU, and ACT). A new species of Umbelopsis was described and illustrated, and subsequently named U. ophiocordycipiticola. The characteristics of U. ophiocordycipiticola exhibited sporangia with a diameter ranging from 8 to 17 µm. and sporangiospores that were oval to ellipsoidal in shape, irregularly angular, with dimensions of ∼1.9-2.9 × 1.7-3.0 µm. Gas chromatography and mass spectrometry (GC-MS) were used to examine the composition of fatty acids. Notably, U. ophiocordycipiticola showed a significantly higher oil content of 50.89% in dry cell weight (DCW) compared to U. vinacea and U. ramanniana. The mean proportion of polyunsaturated fatty acids (PUFAs) in U. ophiocordycipiticola was 32.38%, and the maximum levels of γ-linolenic acid (GLA), arachidonic acid (ARA), eicosapentaenoic acid (EPA), and docosahexaenoic acid (DHA) in U. ophiocordycipiticola were found to be 14.51, 0.24, 0.54, and 0.53%, respectively. The biodiesel quality from all three species complied with applicable standards set by the American Association for Testing and Materials (ASTM 6751) and the Brazilian National Petroleum Agency (ANP 255).

CONCLUSIONS

The establishment of a novel species, U. ophiocordycipiticola, was strongly supported by morphological and molecular evidence. Umbelopsis ophiocordycipiticola exhibited a high-value PUFA content. Additionally, three Umbelopsis species demonstrated good quality for biodiesel production.

Evaluation of fuel properties for possible biodiesel output based on the fatty acid composition of oleaginous plants and microalgae

In the past decade, there has been a significant rise in sustainable biomass based biofuel production to address energy needs while mitigating environmental impacts. Traditionally, bioethanol was used for biofuel production, but concerns over food security and environmental preservation have led to growing interest in alternative sources such as neutral lipids from vegetable oil and microalgae for biodiesel production. This research paper evaluates the potential of various oleaginous plants and microalgae as feedstocks for biodiesel production, with a focus on their fatty acid composition and its impact on biodiesel properties. The study examines the fatty acid profiles of 43 different plant and microalgae species and employs various equations to estimate key physical properties of biodiesel. Additionally, the communication compares these properties to International Biodiesel Standards (EN 14214 and ASTM D6751-08) to assess the suitability of the derived biodiesel for commercial use. It is impossible to describe a single composition that is optimal in terms of all essential fuel properties due to the opposing effects of some structural features of the Fatty Acid Methyl Esters (FAME). However, biodiesel should contain relatively low concentrations of both long chain saturated and polyunsaturated FAME to ensure adequate efficiency in terms of low temperature operability and oxidative stability. The results reveal significant variations in properties amongst different feedstocks, highlighting the importance of feedstock selection in biodiesel production. The study also establishes correlations between various fuel properties, providing valuable insights in to optimizing biodiesel production processes, which will be of great use to researchers, engineers, and stakeholders involved in biodiesel production.

A systematic review on utilization of biodiesel-derived crude glycerol in sustainable polymers preparation

With the rapid development of biodiesel, biodiesel-derived glycerol has become a promising renewable bioresource. The key to utilizing this bioresource lies in the value-added conversion of crude glycerol. While purifying crude glycerol into a pure form allows for diverse applications, the intricate nature of this process renders it costly and environmentally stressful. Consequently, technology facilitating the direct utilization of unpurified crude glycerol holds significant importance. It has been reported that crude glycerol can be bio-transformed or chemically converted into high-value polymers. These technologies provide cost-effective alternatives for polymer production while contributing to a more sustainable biodiesel industry. This review article describes the global production and quality characteristics of biodiesel-derived glycerol and investigates the influencing factors and treatment of the composition of crude glycerol including water, methanol, soap, matter organic non-glycerol, and ash. Additionally, this review also focused on the advantages and challenges of various technologies for converting crude glycerol into polymers, considering factors such as the compatibility of crude glycerol and the control of unfavorable factors. Lastly, the application prospect and value of crude glycerol conversion were discussed from the aspects of economy and environmental protection. The development of new technologies for the increased use of crude glycerol as a renewable feedstock for polymer production will be facilitated by the findings of this review, while promoting mass market applications.

Coordinated Lipid Mobilization during Seed Development and Germination in Peanut (Arachis hypogaea L.)

Peanut (Arachis hypogaea L.) is one of the most important oil crops in the world due to its lipid-rich seeds. Lipid accumulation and degradation play crucial roles in peanut seed maturation and seedling establishment, respectively. Here, we utilized lipidomics and transcriptomics to comprehensively identify lipids and the associated functional genes that are important in the development and germination processes of a large-seed peanut variety. A total of 332 lipids were identified; triacylglycerols (TAGs) and diacylglycerols were the most abundant during seed maturation, constituting 70.43 and 16.11%, respectively, of the total lipids. Significant alterations in lipid profiles were observed throughout seed maturation and germination. Notably, TAG (18:1/18:1/18:2) and (18:1/18:2/18:2) peaked at 23386.63 and 23392.43 nmol/g, respectively, at the final stage of seed development. Levels of hydroxylated TAGs (HO-TAGs) increased significantly during the initial stage of germination. Accumulation patterns revealed an inverse relationship between free fatty acids and TAGs. Lipid degradation was determined to be regulated by diacylglycerol acyltransferase, triacylglycerol lipase, and associated transcription factors, predominantly yielding oleic acid, linoleic acid, and linolenic acid. Collectively, the results of this study provide valuable insights into lipid dynamics during the development and germination of large-seed peanuts, gene resources, and guiding future research into lipid accumulation in an economically important crop.

The analysis of classical, polynomial regression and cubic spline mathematical models in hemp biodiesel optimization: an experimental comparison

Post-pandemic inflationist pressures, climate changes and extremes, regional conflicts, and soaring food prices caused the food crisis to increase rapidly worldwide. This global problem directs producers and researchers to use oils used as feedstock in biodiesel production effectively. In this context, it is important to assay the transesterification parameters and conduct new optimization studies to increase biodiesel yield. In this study, methyl ester was produced from hemp oil by transesterification using sodium hydroxide (NaOH). Next, classical optimization study was carried out to determine the effects of catalyst amount, alcohol:oil molar ratio, reaction temperature, and reaction time variables on biodiesel yield. Secondly, the cubic spline mathematical model (CSMM) and polynomial regression mathematical model (PRMM) were applied to the first data of this optimization. Among these optimization methods, the utmost biodiesel yield registered was 96.115% at hemp seed oil (HSO):methanol molar ratio of 5.59:1, catalyst concentration of 0.531 wt%, reaction temperature of 42.5 °C, reaction time of 62.1 min, and agitation intensity of 600 rpm at PRMM. Some vital fuel properties obtained from HSO biodiesels as a result of three optimizations satisfied the EN 14214 standard. The results illustrated that the optimal yields from CSMM and PRMM are 0.765% and 1.065% higher, respectively, according to the maximum efficiency obtained from the classical optimization. The outcomes showed that CSMM and PRMM are cost-effective, easy to handle, and promising new approaches.

Development of dual strain microalgae cultivation system for the direct carbon dioxide utilization of power plant flue gas

This study aims to propose a biological system that allows for direct utilization of flue gas for carbon dioxide capture and utilization by microalgae. The strain Chlorella sp. ABC-001 is employed for its high growth rate as well as lipid and carbohydrate content. Toxicity tests showed that cell growth was unaffected by NO, but the presence of SO2 showed critical damage on cell growth. Hence, an extremophile alga, Galdieria sulphuraria 5587.1 was applied to build a dual-strain cultivation system to mitigate the effect of SO2 toxicity and increase CO2 capture efficiency. All SO2 was removed by Galdieria culture and the system exhibited stable growth from a simulated flue gas stream containing CO2, NO and SO2. Combined CO2 biofixation rate of 793 mg/L/d and lipid productivity of 113 mg/L/d was achieved. The results showed that this new cultivation system is a promising alternative for reducing CO2 emissions from power plants.

Impact of macronutrients and salinity stress on biomass and biochemical constituents in Monoraphidium braunii to enhance biodiesel production

Microalgal lipids are precursors to the production of biodiesel, as well as a source of valuable dietary components in the biotechnological industries. So, this study aimed to assess the effects of nutritional (nitrogen, and phosphorus) starvations and salinity stress (NaCl) on the biomass, lipid content, fatty acids profile, and predicted biodiesel properties of green microalga Monoraphidium braunii. The results showed that biomass, biomass productivity, and photosynthetic pigment contents (Chl. a, b, and carotenoids) of M. braunii were markedly decreased by nitrogen and phosphorus depletion and recorded the maximum values in cultures treated with full of N and P concentrations (control, 100%). These parameters were considerably increased at the low salinity level (up to 150 mM NaCl), while an increasing salinity level (up to 250 mM NaCl) reduces the biomass, its productivity, and pigment contents. Nutritional limitations and salt stress (NaCl) resulted in significantly enhanced accumulation of lipid and productivity of M. braunii, which represented more than twofold of the control. Furthermore, these conditions have enhanced the profile of fatty acid and biodiesel quality-related parameters. The current study exposed strategies to improve M. braunii lipid productivity for biodiesel production on a small scale in vitro in terms of fuel quality under low nutrients and salinity stress.

Non-targeted discovery of high-value bio-products in Nicotiana glauca L: a potential renewable plant feedstock

The evaluation of plant-based feedstocks is an important aspect of biorefining. Nicotiana glauca is a solanaceous, non-food crop that produces large amounts of biomass and is well adapted to grow in suboptimal conditions. In the present article, compatible sequential solvent extractions were applied to N. glauca leaves to enable the generation of enriched extracts containing higher metabolite content comparing to direct leaf extracts. Typically, between 60 to 100 metabolite components were identified within the fractions. The occurrence of plant fatty acids, fatty acid alcohols, alkanes, sterols and terpenoids was detected by gas liquid chromatography-mass spectrometry (GC-MS) and metabolite identification was confirmed by comparison of physico-chemical properties displayed by available authentic standards. Collectively, co-products such waxes, oils, fermentable sugars, and terpenoids were all identified and quantified. The enriched fractions of N. glauca revealed a high level of readily extractable hydrocarbons, oils and high value co-products. In addition, the saccharification yield and cell wall composition analyses in the stems revealed the potential of the residue material as a promising lignocellulosic substrate for the production of fermentable sugars. In conclusion a multifractional cascade for valuable compounds/commodities has been development, that uses N. glauca biomass. These data have enabled the evaluation of N. glauca material as a potential feedstock for biorefining.

Potential of Lipid Biosynthesis under Heterotrophy in the Marine Diatom Cyclotella cryptica

Despite the theoretical high productivity, microalgae-based oil production is not economically sustainable due to the high cost of photoautotrophic cultures. Heterotrophic growth is a suitable economic alternative to overcoming light dependence and climatic/geographic fluctuations. Here we report data about growth performance, biomass production, and lipid composition of the marine diatom Cyclotella cryptica, chosen as a model strain for biodiesel production in heterothrophy. A repeated-batch process of heterotrophic cultivation has also been investigated to assess the robustness and phenotypic stability. The process consisting of six constant cycle repetitions was carried out for 42 days and led to an average dry biomass production of 1.5 ± 0.1 g L-1 of which 20% lipids composed of 60% triglycerides, 20% phospholipids. and 20% glycolipids. The major fatty acids were C16:0 (∼26%), C16:1 ω-7 (∼57%), and C20:5 ω-3 (∼12%), with a significant reduction in the unsaturated fatty acids in comparison to other microalgae grown in heterotrophy. Fatty acids were differently distributed among the glycerolipid classes, and the lipid composition was used to compare the potential properties of C. cryptica oil with traditional vegetable biofuels.

Abiotic factors improving fatty acid profiling of freshwater indigenous microalgae isolated from Kumaun region of Uttarakhand, India

Microalgae have grabbed huge attention as a potential feedstock for biofuel production in response to the rise in energy consumption and the energy crisis. In the present study, indigenous microalgal strains were isolated from four freshwater lakes in the Kumaun region, Uttarakhand, India. Based on growth and lipid profiles, the four best-performing isolates were selected for further experiments. Initial identification of isolates was done by morphological observations, which were further validated by molecular identification using ITS sequencing. The screened cultures were subjected to abiotic stress conditions (varying concentrations of nitrogen and different temperatures) to monitor the biomass, lipid accumulation, and biochemical compositions (chlorophyll and carotenoids). The quantification of fatty acids was checked via gas chromatographic analysis. The strains were identified as KU_MA3 Chlamydopodium starrii, KU_MA4 Tetradesmus nygaardii, KU_MA5 Desmodesmus intermedius, and KU_MA6 Tetradesmus nygaardii. KU_MA3 Chlamydopodium starrii showed the best results in terms of growth and lipid production at 21 °C and 0.37 g/L NaNO2 concentration. The percentage of fatty acid methyl esters (FAMEs) attained >80% and met the standard for biodiesel properties. The strain has the potential to attain higher biomass and accumulate higher lipid content, and after some more studies, it can be used for upscaling processes and large-scale biodiesel production.

Unlocking the potential of microalgae cultivated on wastewater combined with salinity stress to improve biodiesel production

Microalgae have the potential as a source of biofuels due to their high biomass productivity and ability to grow in a wide range of conditions, including wastewater. This study investigated cultivating two microalgae species, Oocystis pusilla and Chlorococcus infusionum, in wastewater for biodiesel production. Compared to Kühl medium, KC medium resulted in a significant fold increase in cellular dry weight production for both O. pusilla and C. infusionum, with an increase of 1.66 and 1.39, respectively. A concentration of 100% wastewater resulted in the highest growth for O. pusilla, with an increase in biomass and lipid content compared to the KC medium. C. infusionum could not survive in these conditions. For further increase in biomass and lipid yield of O. pusilla, different total dissolved solids (TDS) levels were used. Maximum biomass and lipid productivities were achieved at 3000 ppm TDS, resulting in a 28% increase in biomass (2.50 g/L) and a 158% increase in lipid yield (536.88 mg/g) compared to KC medium. The fatty acid profile of O. pusilla cultivated on aerated wastewater at 3000 ppm TDS showed a high proportion of desirable saturated fatty acids (SFA) and monounsaturated fatty acids (MUFA) for biodiesel production. Cultivating microalgae in wastewater for biodiesel production can be cost-effective, especially for microalgae adapted to harsh conditions. It could be concluded that O. pusilla is a promising candidate for biodiesel production using wastewater as a growth medium, as it has high biomass productivity and lipid yield, and its fatty acid profile meets the standard values of American and European biodiesel standards. This approach offers a sustainable and environmentally friendly solution for producing biofuels while reducing the environmental impact of wastewater disposal.

Genome-Wide Analysis of Glycerol-3-Phosphate Acyltransferase (GPAT) Family in Perilla frutescens and Functional Characterization of PfGPAT9 Crucial for Biosynthesis of Storage Oils Rich in High-Value Lipids

Glycerol-3-phosphate acyltransferase (GPAT) catalyzes the first step in triacylglycerol (TAG) biosynthesis. However, GPAT members and their functions remain poorly understood in Perilla frutescens, a special edible-medicinal plant with its seed oil rich in polyunsaturated fatty acids (mostly α-linolenic acid, ALA). Here, 14 PfGPATs were identified from the P. frutescens genome and classified into three distinct groups according to their phylogenetic relationships. These 14 PfGPAT genes were distributed unevenly across 11 chromosomes. PfGPAT members within the same subfamily had highly conserved gene structures and four signature functional domains, despite considerable variations detected in these conserved motifs between groups. RNA-seq and RT-qPCR combined with dynamic analysis of oil and FA profiles during seed development indicated that PfGPAT9 may play a crucial role in the biosynthesis and accumulation of seed oil and PUFAs. Ex vivo enzymatic assay using the yeast expression system evidenced that PfGPAT9 had a strong GPAT enzyme activity crucial for TAG assembly and also a high substrate preference for oleic acid (OA, C18:1) and ALA (C18:3). Heterogeneous expression of PfGPAT9 significantly increased total oil and UFA (mostly C18:1 and C18:3) levels in both the seeds and leaves of the transgenic tobacco plants. Moreover, these transgenic tobacco lines exhibited no significant negative effect on other agronomic traits, including plant growth and seed germination rate, as well as other morphological and developmental properties. Collectively, our findings provide important insights into understanding PfGPAT functions, demonstrating that PfGPAT9 is the desirable target in metabolic engineering for increasing storage oil enriched with valuable FA profiles in oilseed crops.

Orange Peel Waste as Feedstock for the Production of Glycerol-Free Biodiesel by the Microalgae Nannochloropsis oculata

The bioconversion of agri-food waste into high-value products is gaining growing interest worldwide. Orange peel waste (OPW) is the main by-product of orange juice production and contains high levels of moisture and carbohydrates. In this study, the orange waste extract (OWE) obtained through acid hydrolysis of OPW was used as a substrate in the cultivation of the marine microalgae Nannochloropsis oculata. Photoheterotrophic (PH) and Photoautotrophic (PA) cultivations were performed in OWE medium and f/2 medium (obtained by supplementing OWE with macro- and micronutrients of f/2 medium), respectively, for 14 days. The biomass yields in PA and PH cultures were 390 mg L-1 and 450 mg L-1, while oil yields were 15% and 28%, respectively. The fatty acid (FA) profiles of PA cultures were mostly represented by saturated (43%) and monounsaturated (46%) FAs, whereas polyunsaturated FAs accounted for about 10% of the FAs. In PH cultures, FA profiles changed remarkably, with a strong increase in monounsaturated FAs (77.49%) and reduced levels of saturated (19.79%) and polyunsaturated (2.72%) FAs. Lipids obtained from PH cultures were simultaneously extracted and converted into glycerol-free biodiesel using an innovative microwave-assisted one-pot tandem protocol. FA methyl esters were then analyzed, and the absence of glycerol was confirmed. The FA profile was highly suitable for biodiesel production and the microwave-assisted one-pot tandem protocol was more effective than traditional extraction techniques. In conclusion, N. oculata used OWE photoheterotrophically, resulting in increased biomass and oil yield. Additionally, a more efficient procedure for simultaneous oil extraction and conversion into glycerol-free biodiesel is proposed.

Biodiesel Production from the Marine Alga Nannochloropsis oceanica Grown on Yeast Wastewater and the Effect on Its Biochemical Composition and Gene Expression

Microalgae-based biodiesel synthesis is currently not commercially viable due to the high costs of culture realizations and low lipid yields. The main objective of the current study was to determine the possibility of growing Nannochloropsis oceanica on Saccharomyces cerevisiae yeast wastewater for biodiesel generation at an economical rate. N. oceanica was grown in Guillard F/2 synthetic medium and three dilutions of yeast wastewater (1, 1.25, and 1.5%). Biodiesel properties, in addition to carbohydrate, protein, lipid, dry weight, biomass, lipid productivity, amino acids, and fatty acid methyl ester (FAMEs) content, were analyzed and the quality of the produced biodiesel is assessed. The data revealed the response of N. oceanica to nitrogen-deficiency in the three dilutions of yeast wastewater. N. oceanica in Y2 (1.25%) yeast wastewater dilution exhibited the highest total carbohydrate and lipid percentages (21.19% and 41.97%, respectively), and the highest lipid productivity (52.46 mg L-1 day -1) under nitrogen deficiency in yeast wastewater. The fatty acids profile shows that N. oceanica cultivated in Y2 (1.25%) wastewater dilution provides a significant level of TSFA (47.42%) and can be used as a feedstock for biodiesel synthesis. In addition, N. oceanica responded to nitrogen shortage in wastewater dilutions by upregulating the gene encoding delta-9 fatty acid desaturase (Δ9FAD). As a result, the oleic and palmitoleic acid levels increased in the fatty acid profile of Y2 yeast wastewater dilution, highlighting the increased activity of Δ9FAD enzyme in transforming stearic acid and palmitic acid into oleic acid and palmitoleic acid. This study proved that the Y2 (1.25%) yeast wastewater dilution can be utilized as a growth medium for improving the quantity of specific fatty acids and lipid productivity in N. oceanica that affect biodiesel quality to satisfy global biodiesel requirements.

A biphasic photobioreactor system for consecutive extraction of lipids and carotenoids from pre-hydrolysed microalgae and evaluation of its biodiesel potential

A green extraction method is developed using partially hydrolysed microalgal cells grown in biocompatible solvent for simultaneous cultivation and extraction of bioproducts from a highly efficient permeabilized microalgal cell with enhanced biomass and lipid content for potential use in biodiesel production. Incomplete digestion of cell wall was achieved by regulating the incubation time of the enzymatic pretreatment of the microalgal cells. 15.77% increase in lipid content was seen when untreated cells were cultured with biocompatible solvent, while cultivation of these enzymatically pretreated cells with biocompatible solvent, the lipid content increased by 53.33% and 22% higher carotenoid content was observed as compared to conventional extraction. The total fatty acids obtained after 1st and 2nd extractions in untreated samples were 67.82%, while those in enzymatically partially digested samples were 91.94%. The untreated and partially enzymatically predigested strain showed suitable properties for quality biodiesel production as per international recommendations. The cost benefit analysis of the overall process showed the use of biocompatible solvent coupled to enzymatically predigested biomass was a favorable option as compared to conventional extraction.

Experimental and theoretical assessment of phenomena linked with separation and purification of biodiesel from Ricinus communis seed oil

This study investigated the phenomena associated with the separation and purification of biodiesel produced from Ricinus communis oil seeds using experimental and theoretical approaches. The alkaline transesterification technique was used to produce the biodiesel from the Ricinus communis oil seeds which were later compared with standards based on EN and ASTM. Experimental investigation of the components in the mixture for separation and purification was conducted using the standard turbidimetric method for binodal solubility and tie-line compositions. The gas chromatographic technique was used to determine the composition of the homogeneous mixture. Novel components separation and purification of the Ricinus communis seed oil biodiesel was achieved using ternary diagrams highlighting the constituent components of the biodiesel at different temperatures for enhanced separation and purification. At the coexisting extract and raffinate phases, the orientation angle of the component compositions increases as the methanol concentration increases and temperature increases. The analysis of seed oil in terms of its physicochemical properties showed density, refractive index, acid value, and free fatty acid values of 905 kg/m³, 1.486, 0.79 mg KOH/g, and 0.390 mg KOH/g respectively. The fatty acid composition of the seed oil and biodiesel revealed that the major characteristics of the oil and biodiesel were defined by the presence of linoleic acid (C_18:2) and a ricinoleic acid hydroxyl group (C_18:1, OH) with compositions of approximately 30% and 20% respectively. Fourier Transform Infra-Red (FTIR) spectrometry analysis of the oil and biodiesel showed that the absorption spectrum in terms of the wave number (cm^-1) ranged from 1000 to 4000 cm^-1 with esters as the main functional group providing the main structural backbone. The presence of different fatty acids leads to lateral homogeneity of the biodiesel molecules which can serve to organize the molecules into discrete domains with different properties for enhanced separation and purification at the investigated temperatures. Optimal separation and purification were achieved at the different temperatures showing the castor oil biodiesel, glycerol, and methanol components system at the prevailing composition, time, and temperatures from the tie-lines and binodal solubility compositions. This approach provides a means for the design of a more efficient separation process for optimal biodiesel purification after production with knowledge of how the components are distributed in the ternary mixture after the transesterification reaction. This, leads to greater efficiency of the process, reducing material and operational costs and eliminating environmental issues linked with the biodiesel production process as the volume of wastewater generated would be hugely eradicated. The findings of this study will be useful in the setting up of a small-to-medium-size biodiesel production facility with improvement in the efficiency of product separation and purification.

Determination of superior Pistacia chinensis accession with high-quality seed oil and biodiesel production and revelation of LEC1/WRI1-mediated high oil accumulative mechanism for better developing woody biodiesel

BACKGROUND

Based on our previous studied on different provenances of Pistacia chinensis, some accessions with high quality and quantity of seed oils has emerged as novel source of biodiesel. To better develop P. chinensis seed oils as woody biodiesel, a concurrent exploration of oil content, FA profile, biodiesel yield, and fuel properties was conducted on the seeds from 5 plus germplasms to determine superior genotype for ideal biodiesel production. Another vital challenge is to unravel mechanism that govern the differences in oil content and FA profile of P. chinensis seeds across different accessions. FA biosynthesis and oil accumulation of oil plants are known to be highly controlled by the transcription factors. An integrated analysis of our recent transcriptome data, qRT-PCR detection and functional identification was performed as an attempt to highlight LEC1/WRI1-mediated transcription regulatory mechanism for high-quality oil accumulation in P. chinensis seeds.

RESULTS

To select ideal germplasm and unravel high oil accumulative mechanism for developing P. chinensis seed oils as biodiesel, five plus trees (accession PC-BJ/PC-AH/PC-SX/PC-HN/PC-HB) with high-yield seeds were selected to assess the variabilities in weight, oil content, FA profile, biodiesel yield and fuel property, revealing a variation in the levels of seed oil (50.76-60.88%), monounsaturated FA (42.80-70.72%) and polyunsaturated FA (18.78-43.35%), and biodiesel yield (84.98-98.15%) across different accessions. PC-HN had a maximum values of seed weight (26.23 mg), oil (60.88%) and biodiesel yield (98.15%), and ideal proportions of C18:1 (69.94%), C18:2 (17.65%) and C18:3 (1.13%), implying that seed oils of accession PC-HN was the most suitable for ideal biodiesel production. To highlight molecular mechanism that govern such differences in oil content and FA profile of different accessions, a combination of our recent transcriptome data, qRT-PCR detection and protein interaction analysis was performed to identify a pivotal role of LEC1/WRI1-mediated transcription regulatory network in high oil accumulation of P. chinensis seeds from different accessions. Notably, overexpression of PcWRI1 or PcLEC1 from P. chinensis seeds in Arabidopsis could facilitate seed development and upregulate several genes relevant for carbon flux allocation (plastidic glycolysis and acetyl-CoA generation), FA synthesis, TAG assembly and oil storage, causing an increase in seed oil content and monounsaturated FA level, destined for biodiesel fuel property improvement. Our findings may present strategies for better developing P. chinensis seed oils as biodiesel feedstock and bioengineering its high oil accumulation.

CONCLUSIONS

This is the first report on the cross-accessions assessments of P. chinensis seed oils to determine ideal accession for high-quality biodiesel production, and an effective combination of PcWRI1 or PcLEC1 overexpression, morphological assay, oil accumulation and qRT-PCR detection was applied to unravel a role of LEC1/WRI1-mediated regulatory network for oil accumulation in P. chinensis seeds, and to highlight the potential application of PcWRI1 or PcLEC1 for increasing oil production. Our finding may provide new strategies for developing biodiesel resource and molecular breeding.

Cultivation of Pseudochlorella pringsheimii for biodiesel production in a scalable indoor photobioreactor: case studies from Egypt

BACKGROUND

Enhancement of lipid accumulation is the major strategy to improve the commercial feasibility of microalgae as a source for biodiesel production. Pseudochlorella pringsheimii (Formally was named as Chlorella ellipsoidea) green microalgae strain was chosen with respect to their ability as a potential source to produce high lipids content, could be used for the production of biofuel, which can be an alternative renewable energy source instead of fossil fuels.

RESULTS

Initially, the Pseudochlorella pringsheimii microalgae was evaluated on the basis of tested at Lab scales 2 L by applicable different nutrient individual of N, P, Fe conditions in BBM medium concentrations for choosing the best concentrations induce lipid contents and productivity to cultivate in large scale in the 2000 L PBR. The suitable concentrations of nutrients with highest lipid contents were obtained under deficient of nitrogen (1.25 gL^-1, limited N) and phosphorus (0.1 mg L^-1, limited P) coupled with high iron concentration (10 mg L, rich Fe) and CO₂ (6%). Therefore, their collective of nutrients was applied to culture of microalgae cells at large scale in 2000 L photobioreactor (PBR model), which, this techniques was used to quantify high lipid contents (25% w/w) and high lipid productivity (74.07 mgL^-1 day^-1). The inducted lipid conversion to biodiesel via transestrification process was 91.54 ± 1.43%. The fatty acid methyl esters (FAMEs profile by means of GC/MS resulted in C16:0, C18:1, C18:2, C18:3 as a main constituents. With regard to physical-chemical property (such as density, kinematic viscosity, gravity, and certain number), the Pseudochlorella pringsheimii biodiesel have biofuel properties, in accordance with appropriate biodiesel properties, as ASTM and EU standards, that thereby referring to high quality biodiesel.

CONCLUSIONS

Pseudochlorella pringsheimii cultured in large scale in photobioreactor under stress condition have a high potential of lipids production with high quality of FAMEs that can be used as a promising biodiesel fuel. It has also a potential to be applied for commercialization based on the techno-economic and environmental impacts.

Efficient use of discarded vegetal residues as cost-effective feedstocks for microbial oil production

BACKGROUND

Horticultural intensive type systems dedicated in producing greenhouse vegetables are one of the primary industries generating organic waste. Towards the implementation of a zero-waste strategy, this work aims to use discarded vegetables (tomato, pepper and watermelon) as feedstock for producing microbial oil using the oleaginous yeast Cryptococcus curvatus.

RESULTS

The soluble fraction, resulting after crushing and centrifuging these residues, showed C/N ratios of about 15, with a total carbohydrate content (mainly glucose, fructose and sucrose) ranging from 30 g/L to 65 g/L. Using these liquid fractions as substrate under a pulse-feeding strategy with a concentrated glucose solution resulted in an intracellular total lipid accumulation of about 30% (w/w) of the total dry cell weight (DCW). To increase this intracellular lipid content, the initial C/N content was increased from 15 to 30 and 50. Under these conditions, the process performance of the pulse-feeding strategy increased by 20-36%, resulting in a total intracellular lipid concentration of 35-40% DCW (w/w).

CONCLUSION

These results demonstrate the potential of discarded vegetables as a substrate for producing bio-based products such as microbial oil when proper cultivation strategies are available.

Chemical composition and species identification of microalgal biomass grown at pilot-scale with municipal wastewater and CO2 from flue gases

The production potential of a locally isolated Chlorella vulgaris strain and a local green-algae consortium, used in municipal wastewater treatment combined with CO₂ sequestration from flue gases, was evaluated for the first time by comparing the elemental and biochemical composition and heating value of the biomass produced. The microalgae were grown in outdoor pilot-scale ponds under subarctic summer conditions. The impact of cultivation in a greenhouse climate was also tested for the green-algae consortium; additionally, the variation in species composition over time in the three ponds was investigated. Our results showed that the biomass produced in the consortium/outdoor pond had the greatest potential for bioenergy production because both its carbohydrates and lipids contents were significantly higher than the biomasses from the consortium/greenhouse and C. vulgaris/outdoor ponds. Although greenhouse conditions significantly increased the consortium biomass's monounsaturated fatty acid content, which is ideal for biodiesel production, an undesirable increase in ash and chemical elements, as well as a reduction in heating value, were also observed. Thus, the placement of the pond inside a greenhouse did not improve the production potential of the green-algae consortium biomass in the current study infrastructure and climate conditions.

Scenedesmus sp. strain SD07 cultivation in municipal wastewater for pollutant removal and production of lipid and exopolysaccharides

In this study, an efficient microalgal strain SD07 was isolated from pond wastewater and identified as Scenedesmus sp. using the 18S rRNA gene sequence analysis. The strain SD07 was grown in a variety of concentrations (25-100%) of municipal wastewater. Scenedesmus sp. strain SD07 grown in 75% diluted wastewater produced a higher amount of biomass (1.93 ± 0.10 g L^-1), and removal of chemical oxygen demand (COD), ammonium (NH₄⁺), total nitrogen (TN) and total phosphate (TP) by 91.36%, 88.41%, 93.26% and 96.32%, respectively from wastewater. The harvested strain SD07 biomass has protein, carbohydrate and lipid contents of 35%, 20.4% and 33%, respectively. Fatty acid profiles revealed that the strain SD07 lipids mainly consist of palmitic acid (40.5%), palmitoleic acid (19%), linoleic acid (17%) and oleic acid (13.2%). Furthermore, strain SD07 cultured in 75% diluted wastewater produced 378 mg L^-1 of exopolysaccharides (EPS). The EPS was utilized as a biostimulant in the cultivation of Solanum lycopersicum under salinity stress. In summary, these findings suggest that this Scenedesmus sp. strain SD07 can be employed for wastewater treatment as well as the production of valuable biomass, high-quality algal oil and EPS.

Evaluation of oil accumulation and biodiesel property of Lindera glauca fruits among different germplasms and revelation of high oil producing mechanism for developing biodiesel

BACKGROUND

Lindera glauca with rich resource and fruit oil has emerged as novel source of biodiesel in China, but different germplasms show a variation for fruit oil content and FA profile. To develop L. glauca fruit oils as biodiesel, a concurrent exploration of oil content, FA composition, biodiesel yield, fuel property and prediction model construction was conducted on the fruits from 8 plus germplasms to select superior genotype for ideal biodiesel production. Another vital focus was to highlight mechanism that govern the differences in oil content and FA profile of different germplasms. The cross-accessions comparisons associated with oil-synthesized gene transcriptional level and oil accumulative amount led to the identification of potential determinants (enzymes, transporters or transcription factors) and regulatory mechanisms responsible for high-quality oil accumulation.

RESULTS

To select superior germplasm and unravel regulatory mechanism of high oil production for developing L. glauca fruit oils as biodiesel, 8 plus trees (accession LG01/02/03/04/05/06/07/08) with high-yield fruits were selected to evaluate the differences in oil content, FA profile, biodiesel yield and fuel property, and to construct fuel property prediction model, revealing a variation in the levels of fruit oil (45.12-60.95%), monounsaturated FA (52.43-78.46%) and polyunsaturated FA (17.69-38.73%), and biodiesel yield (80.12-98.71%) across different accessions. Of note, LG06 had a maximum yield of oil (60.95%) and biodiesel (98.71%), and ideal proportions of C18:1 (77.89%), C18:2 (14.16%) and C18:3 (1.55%), indicating that fruit oils from accession LG06 was the most suitable for high-quality biodiesel production. To highlight molecular mechanism that govern such differences in oil content and FA composition of different accessions, the quantitative relationship between oil-synthesized gene transcription and oil accumulative amount were conducted on different accessions to identify some vital determinants (enzymes, transporters or transcription factors) with a model of carbon metabolic regulatory for high-quality oil accumulation by an integrated analysis of our recent transcriptome data and qRT-PCR detection. Our findings may present strategies for developing L. glauca fruit oils as biodiesel feedstock and engineering its oil accumulation.

CONCLUSIONS

This is the first report on the cross-accessions evaluations of L. glauca fruit oils to determine ideal accession for producing ideal biodiesel, and the associations of oil accumulative amount with oil-synthesized gene transcription was performed to identify some crucial determinants (enzymes, transporters or transcription factors) with metabolic regulation model established for governing high oil production. Our finding may provide molecular basis for new strategies of developing biodiesel resource and engineering oil accumulation.

A low-cost technique for biodiesel production in Ankistrodesmus sp. EHY by using harvested microalgal effluent

The present study aims to use Ankistrodesmus sp. EHY to develop a viable and economic lipid production strategy using recycling of harvested microalgal effluent. In comparison to the control, the highest lipid content (52.4 %) and productivity (250.72 mg L^-1 d^-1) were achieved when 40 % recycled medium was used. Consistent with the trend of lipid accumulation, the six key lipogenetic genes were upregulated, as well as reactive oxygen species (ROS), glutathione (GSH) and genes encoding antioxidant enzymes during cultivation in recycled medium. Moreover, the consumption of dissolved organic carbon (DOC) and the increased humic acid (HA) in the recycled medium might also be associated with lipid biosynthesis. The biodiesel parameters of alga biomass-derived lipids were fitted to the standard of commercial biodiesel. In conclusion, this study offers an economically viable strategy for microalgal biofuel production and wastewater treatment using recycling of harvested microalgal effluent.

A review on properties, challenges and commercial aspects of eco-friendly biolubricants productions

Lubricants operate as antifriction media, preserving machine reliability, facilitating smooth operation, and reducing the likelihood of frequent breakdowns. The petroleum-based reserves are decreasing globally, leading to price increases and raising concerns about environmental degradation. The researchers are concentrating their efforts on developing and commercializing an environmentally friendly lubricant produced from renewable resources. Biolubricants derived from nonedible vegetable oils are environmentally favorable because of their non-toxicity, biodegradability, and close to net zero greenhouse gas emissions. The demand for bio lubricants in industry and other sectors is increasing due to their non-toxic, renewable, and environmentally friendly nature. Good lubrication, anti-corrosion, and high flammability are characteristic properties of vegetable oils due to their unique structure. This study presents several key properties of nonedible oils that are used to produce lubricants via the transesterification process. Bibliometric analysis is also performed, which provides us with a better understanding of previous studies related to the production of bio lubricants from the transesterification process. Only 371 published documents in the Scopus database were found to relate to the production of bio lubricants using the transesterification process. The published work was mostly dominated by research articles (286; 77.088%). Significant development can be seen in recent years, with the highest occurrence in 2021, reaching 68 publications accounting for 18.38% of the total documents. In the second step, (i) the authors with the most number of publications; (ii) journals with the most productions; (iii) most productive countries; and (iv) the authors' most frequently used keywords were evaluated. These results will provide a pathway for researchers interested in this field. Lastly, recommendation is made on research gaps to device possible strategies for its commercialization.

Extracellular polymeric substance profiling and biophysical analysis reveal influence factors of spontaneous flocculation in rich lipid alga Heveochlorella sp. Yu

Microalgae harvest and lipid accumulation were important factors influencing commercialized development of microalgae biodiesel. Spontaneous flocculation was an ideal method in microalgae harvest, but few rich lipid microalgae could be harvested by spontaneous flocculation. Rich lipid alga Heveochlorella sp. Yu has a characteristic of spontaneous flocculation to be harvested. Heveochlorella sp. Yu has high lipid productivity (105.24 mg L^-1 d^-1) and fine spontaneous flocculation efficiency (82.93 %, 2 h) on early stationary phase (day 9). The polysaccharides consisting of glucose, mannose, galactose, rhamnose and fructose (8.67:4.90:3.27:2.16:1) in loose-bound extracellular polymeric substance (LB-EPS) might make great contribution in microalgae flocculation. Meanwhile, the zeta potential close to zero was also beneficial to microalgae flocculation. Besides, the adhesion free energy related with cells adhesion was detected by thermomechanical analysis. Afterward, Extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) theory was utilized to quantitatively evaluate short-range interactions involved in the spontaneous aggregation among cells. Collectively, biophysical analyses indicated that content and composition of EPS, Zeta potential, thermodynamic parameter and total interaction based on XDLVO theory were closely connected with spontaneous flocculation in microalga Yu. Our study provided a harvest-simplified process of rich microalgae, which proposes a new idea for commercial development of microalgae biodiesel.