Microbial fuel cells operating on mixed fatty acids

Propionate outperforms conventional acetate as electron donors for highly-sensitive electrochemical active biofilm sensors in water biotoxicity early-warning

With the ability to generate in situ real-time electric signals, electrochemically active biofilm (EAB) sensors have attracted wide attention as a promising water biotoxicity early-warning device. Organic matters serving as the electron donors potentially affect the electric signal's output and the sensitivity of the EAB sensor. To explore the influence of organic matters on EAB sensor's performance, this study tested six different organic matters during the sensor's inoculation. Besides the acetate, a conventional and widely used organic matter, propionate and lactate were also found capable of starting up the sensor. Moreover, the propionate-fed (PF) sensor delivered the highest sensitivity, which are respectively 1.4 times and 2.8 times of acetate-fed (AF) sensor and lactate-fed (LF) sensor. Further analysis revealed that EAB of PF sensor had more vulnerable intracellular metabolism than the others, which manifested as the most severe energy metabolic suppression and reactive oxygen species attack. Regarding the microbial function, a two-component system that was deemed as an environment awareness system was found in the EAB of PF, which also contributed to its high sensitivity. Finally, PF sensor was tested in real water environment to deliver early-warning signals.

Enhanced degradation and methane production of food waste anaerobic digestate using an integrated system of anaerobic digestion and microbial electrolysis cells for long-term operation

The integrated system of anaerobic digestion and microbial electrolysis cells (AD-MEC) was a novel approach to enhance the degradation of food waste anaerobic digestate and recover methane. Through long-term operation, the start-up method, organic loading, and methane production mechanism of the digestate have been investigated. At an organic loading rate of 4000 mg/L, AD-MEC increased methane production by 3-4 times and soluble chemical oxygen demand (SCOD) removal by 20.3% compared with anaerobic digestion (AD). The abundance of bacteria Fastidiosipila and Geobacter, which participated in the acid degradation and direct electron transfer in the AD-MEC, increased dramatically compared to that in the AD. The dominant methanogenic archaea in the AD-MEC and AD were Methanobacterium (44.4-56.3%) and Methanocalculus (70.05%), respectively. Geobacter and Methanobacterium were dominant in the AD-MEC by direct electron transfer of organic matter into synthetic methane intermediates. AD-MEC showed a perfect SCOD removal efficiency of the digestate, while methane as clean energy was obtained. Therefore, AD-MEC was a promising technology for deep energy transformation from digestate.

Development of bioanodes rich in exoelectrogenic bacteria using iron-rich palaeomarine sediment inoculum

Microbial Fuel Cells (MFC) convert energy stored in chemicals into electrical energy thanks to exoelectrogenic microorganisms who also play a crucial role in geochemical cycles in their natural environment, including that of iron. In this study, we investigated paleomarine sediments as inoculum for bioanode development in MFCs. These sediments were formed under anoxic conditions ca. 113 million years ago and are rich in clay minerals, organic matter, and iron. The marlstone inoculum was incubated in the anolyte of an MFC using acetate as the added electron donor and ferricyanide as the electron acceptor in the catholyte. After seven weeks of incubation, the current density increased to 0.15 mA.cm-2 and a stable + 700 mV open circuit potential was reached. Community analysis revealed the presence of two exoelectrogenic bacterial genera, Geovibrio and Geobacter. Development of electroactive biofilms was correlated to bulk chemical transformations of the sediment inoculum with an increase in the Fe(II) to Fetotal ratio. Comparisons to sediments sterilized prior to inoculation confirmed that bioanode development derives from the native microbiota of these paleomarine sediments. This study illustrates the feasibility of developing exoelectrogenic biofilms from iron-rich marlstone and has implications for the role of such bacteria in broader paleoenvironmental phenomena.

New insights into antibiotic stimulation of methane production during anaerobic digestion

Residual antibiotics in swine wastewater pose a critical challenge for stable anaerobic digestion (AD). This study offers fresh insights into the anaerobic treatment of swine wastewater. The results showed that the presence of three typical antibiotics (sulfamethoxazole (SMX), oxytetracycline (OTC) and ciprofloxacin (CIP)) in swine wastewater could promote methane production by stimulating the production and conversion of ethanol. Among them, SMX exhibited the strongest methane promotion effect, with the cumulative methane production increasing from 138.47 to 2204.19 mL/g VS. According to the microbial community structure, antibiotics could promote the growth of Corynebacterium, Lutispora and hydrogenotrophic methanogens (Methanosassiliicoccus, Methanobrevibacter, and Methanobacterium), but inhibit the enrichment of acetoclastic methanogen (Methanosaeta). The relative abundance of Methanosaeta decreased from 2.93-19.80% to 0.52-2.58% under antibiotic stress. Furthermore, there were significant differences in the influence of different antibiotic types on methanogenic pathways. Specifically, OTC and CIP promoted the acetoclastic and hydrogenotrophic pathways, respectively, to enhance methane production. However, SMX could promote both acetoclastic and hydrogenotrophic pathways.

Investigate the anaerobic degradation of high-acetone latex wastewater with magnetite supplement

This study evaluated the effects of acetone on the anaerobic degradation of synthetic latex wastewater, which was simulated from the wastewater of the deproteinized natural rubber production process, including latex, acetate, propionate, and acetone as the main carbon sources, at a batch scale in 5 cycles of a total of 60 days. Fe3O4 was applied to accelerate the treatment performance from cycle 3. Acetone was added in concentration ranges of 0%, 0.05%, 0.1%, 0.15%-included latex, and 0.15%-free latex (w/v). In the Fe3O4-free cycles, for latex-added vials, soluble chemical oxygen demand (sCOD) was removed at 43.20%, 43.20%, and 12.65%, corresponding to the input acetone concentrations varying from 0.05% to 0.15%, indicating the interference of acetone for COD reduction. After adding Fe3O4, all flasks reported a significant increase in COD removal efficiency, especially for acetone-only and latex-only vials, from 36.9% to 14.30%-42.95% and 83.20%, respectively. Other highlighted results of COD balance showed that Fe3O4 involvement improved the degradation process of acetate, propionate, acetone, and the other COD parts, including the intermediate products of latex reduction. Besides, during the whole batch process, the order of reduction priority of the carbon sources in the synthetic wastewater was acetate, propionate and acetone. We also found that the acetate concentration appeared to be strongly related to reducing other carbon sources in natural rubber wastewater. Microbial community analysis revealed that protein-degrading bacteria Bacteroidetes vadinHA17 and Proteinniphilum and methylotrophic methanogens might play key roles in treating simulated deproteinized-natural-rubber wastewater.

Evolution and interaction of microbial communities in mangrove microbial fuel cells and first description of Shewanella fodinae as electroactive bacterium

Understanding exoelectrogenic bacteria mechanisms and their interactions in complex biofilm is critical for the development of microbial fuel cells (MFCs). In this article, assumptions concerning the benefits of the complex sediment microbial community for electricity production were explored with both the complex microbial community and isolates identified as Shewanella. Analysis of the microbial community revealed a strong influence of the sediment community on anodes and electrolytes compared to that of only water. Moreover, while Pelobacteraceae-related genera were dominant in our MFCs instead of Desulfuromonas and Geobacter as usually reported, the electroactive Shewanella algae and Shewanella fodinae were isolated and cultivated from the anodic biofilm. S. fodinae, described for the first time as an electroactive bacterium to the best of our knowledge, led to a maximal current density of 3.6 A/m² set as 0.3 V/SCE in a three-electrode set-up fed with lactate. S. algae, in a complex medium containing several available substrates, showed several preferential oxidative behaviors including a diauxic behavior. In pure culture and under our conditions, S. fodinae and S. algae were not able to use acetate as a sole electron donor. However, their presence in our acetate-fed MFCs and the adaptive behavior of S. algae hint a syntrophic interaction between the bacteria to optimize the use of the substrate in a complex environment.

Use of Microbial Fuel Cells for the Treatment of Residue Effluents Discharged from an Anaerobic Digester Treating Food Wastes

One of practical challenges in anaerobic-digestion (AD) technology is the cost-effective treatment of residue effluents containing high concentrations of organics, nitrogen and phosphorus (CNP). In order to evaluate the utility of microbial fuel cells (MFCs) for treating anaerobic-digester effluents (ADEs) and generating power from them, laboratory-scale single-chamber MFCs were filled with ADE obtained from a commercial AD plant treating food wastes and thereafter operated by routinely supplying ADE at different hydraulic residence times (HRTs, 5 to 20 days). It is shown that MFCs were able to reduce not only organics in ADE but also nitrogen and phosphorus. For instance, data demonstrated that over 50% of CNP was removed in MFCs operated at an HRT of 10 days, at which the maximum power density reached over 200 mW m−2 (based on the projected area of anode). Metabarcoding of 16S rRNA genes showed that some bacteria were specifically enriched in anode biofilms, suggesting their involvement in power generation. Our study suggests that MFCs are applicable to reducing CNP in ADEs at reasonable rates, and provides subsequent work with fundamental data useful for setting targets for further developments.

Exploring necessity to pre-treat organic fraction of waste prior to use in an earthen MFC modified with bentonite

In this study, the addition of bentonite at different proportions as clay minerals and various thicknesses (4, 5, and 6 mm) of ceramic membranes were evaluated for proton and oxygen mass transfer coefficients. Bentonite (20% and 4 mm) was found to be optimum and was then employed to assess earthen microbial fuel cell (EMFC) performance for different substrates (kitchen waste (KW) slurry and leachate) under batch mode. Both substrates were added in different concentrations of chemical oxygen demand (COD), i.e., 18, 15.2, 12.5, 9.7, and 6.9 g/L to EMFCs. The EMFC achieved superior organic removals for leachate (>96%). Intriguingly, the volatile fatty acids (VFAs) generation and consumption were different for each substrate. Each system expressed affinity towards acetic acid, but limited VFAs (acetic and propionic) were generated by KW while leachate generated acetic, propionic, and butyric. The leachate concentration having COD of 15.2 g/L produced the highest power density of 586.5 ± 38.8 mW/m³, while for KW, only 41.5 mW/m³ (6.9 g/L of COD for KW) was obtained. The study consolidates the need for an intermediate step to pre-treat the organic fraction of waste before its use for resource recovery. Bentonite was found as an effective clay mineral for manufacturing ceramic membranes.

Synergistic degradation for o-chlorophenol and enhancement of power generation by a coupled photocatalytic-microbial fuel cell system

A hierarchically photocatalytic microbial fuel cell system (PMFC) coupled with TiO₂ photoanode and bioanode was established to enhance the power generation based on single-chamber MFC. Compared with the conventional anaerobic mode, oxygen in the solution could be utilized by the photoanode of PMFC to improve the removal of o-chlorophenol (2-CP). The maximum power densities were increasing from 261 (MFC) to 301 mW/m² (PMFC). The removal efficiency of 2-CP (5 mg/L) in PMFC was 76.20% and higher than that in MFC (19.33%) and by photocatalysis (49.23%). The electron-hole separation efficiencies were decreasing with the increasing of dissolved oxygen, causing a low efficiency of photocatalysis, due to the reduction of the current density of the systems. The abundance of Geobacter sp., PHOS-HE36 fam., and Pseudomonas sp. was increased with illumination, contributing to improve the electricity production and 2-CP degradation. The only detective intermediate of 1,2-dichlorobenzene in PMFC indicated that the microbes could regulate the degradation pathway of 2-CP in the coupling system. These findings provided an feasible method for the effective degradation of refractory organic compounds and simultaneous energy recovery by combining photocatalysis and microbial power generation.

Dark fermentation: Production and utilization of volatile fatty acid from different wastes- A review

Volatile fatty acids (VFAs) are the building blocks of the chemical industry, and they are the primary contributors to the planet's organic carbon cycle. VFA production from fossil fuels (mostly petroleum) is unsustainable, pollutes the environment, and generates greenhouse gases. As a result of these issues, there is a pressing need to develop alternate sources for the long-term generation of VFAs via anaerobic digestion. The accessible feedstocks for its sustainable production, as well as the influencing parameters, are discussed in this review. The use of VFAs as a raw material to make a variety of consumer products is reviewed in order to find a solution. It also bridges the gap between traditional and advanced VFA production and utilization methods from a variety of solid and liquid waste sources for economical stability.

Bio-based carbon materials with multiple functional groups and graphene structure to boost methane production from ethanol anaerobic digestion

This study evaluated the effects of bio-based carbon materials on methane production by anaerobic digestion. The results showed that biochar and hydrochar can promote cumulative methane yield by 15% to 29%. However, there was no statistical significance (p > 0.05) between hydrochar and biochar produced at different temperature on methane production. 16S rRNA gene sequencing and bioinformatics analysis showed that biochar and hydrochar enriched microorganism that might participate in direct interspecies electron transfer (DIET) such as Pseudomonadaceae, Bacillaceae, and Clostridiaceae. The the surface properties of the modified biochar were characterized with BET, Raman, FTIR and XPS. Bio-based carbon materials with uniform dispersion provided a stable environment for the DIET of microorganisms and electrons are transferred through aromatic functional groups on the surface of materials. This study reveals bio-based carbon materials surface properties on methane production in anaerobic digestion and provides a new approach to recycling spent coffee grounds.

Butyrate production and purification by combining dry fermentation of food waste with a microbial fuel cell

This study developed and evaluated a high-purity butyrate producing bioprocess from food waste by combining dry fermentation (DF) with a microbial fuel cell (MFC). Acclimatization of a DF reactor with an enrichment culture resulted in high food waste degradation (VS removed, %) and butyrate production. A high VS degradation of 81%, butyrate concentration of up to 24 gCOD_butyrate/L and butyrate yields of 497 gCOD_butyrate/kg VS_added was obtained in the DF reactor. As a result, butyrate comprised 83% of all short chain fatty acids (SCFA) in the DF broth. Acetate (10%) and propionate (7%) comprised the rest of the SCFA. The butyrate composition was further purified by feeding the DF broth to a multi-electrode MFC enriched with anode respiring bacteria (ARB) such as Geobacter sp. (>55%). The ARB in the MFC removed acetate and propionate while purified butyrate was recovered in the MFC effluent. Butyrate purity in the MFC effluent reached as high as 99% at hydraulic retention time of 72 h. Along with butyrate purification, the MFC produced electric power in a range of 0.1-0.6 Wh/gCODbutyrate_recovered (or 0.01-7.85 kWh/ton of food waste), demonstrating that MFCs can be an energy-positive butyrate purification bioprocess.

Potential Valorization of Organic Waste Streams to Valuable Organic Acids through Microbial Conversion: A South African Case Study

The notion of a “biobased economy” in the context of a developing country such as South Africa (SA) necessitates the development of technologies that utilize sustainable feedstocks, have simple and robust operations, are feasible at small scale and produce a variety of valuable bioproducts, thus fitting the biorefinery concept. This case study focuses on the microbial production of higher-value products from selected organic waste streams abundant in the South African agricultural sector using microbes adapted to utilize different parts of biomass waste streams. A ruminant-based carboxylate platform based on mixed or undefined anaerobic co-cultures of rumen microorganisms can convert the carbohydrate polymers in the lignocellulosic part of organic waste streams to carboxylic acids that can be upgraded to biofuels or green chemicals. Furthermore, yeast and fungi can convert the simpler carbohydrates (such as the sugars and malic acid in grape and apple pomace) to ethanol and high-value carboxylic acids, such as lactic, fumaric, succinic and citric acid. This review will discuss the combinational use of the ruminal carboxylate platform and native or recombinant yeasts to valorize biomass waste streams through the production of higher-value organic acids with various applications.

Biocatalyst physiology and interplay: a protagonist of MFC operation

Microbial fuel cells (MFC) have been foreseen as a sustainable renewable energy resource to meet future energy demand. In the past, several studies have been executed in both benchtop and pilot scale to produce electrical energy from wastewater. The key role players in this technology that leads to the operation are microbes, mainly bacteria. The dominant among them is termed as "exoelectrogens" that have the capability to produce and transport electron by utilizing waste source. The current review focuses on such electrogenic bacteria's involvement for enhanced power generation of MFC. The pathway of electron transfer in their cell along and its conduction to the extracellular environment of the MFC system are critically discussed. The interaction of the microbes in various MFC operational conditions, including the role of substrate and solid electron acceptors, i.e., anode, external resistance, temperature, and pH, was also discussed in depth along with biotechnological advancement and future research perspective.

Effect of substrate ratios on the simultaneous carbon, nitrogen, sulfur and phosphorous conversions in microbial fuel cells

The columbic efficiency, removal efficiency and voltage production of seven different combinations of carbon (acetic acid, albumin and sucrose) with nutrients (C:N, C:P, C:S, C:N:S, C:P:S, C:N:P and C: N:S:P) were investigated at three different ratios (20:1, 15:1 and 10:1). The effects of various pH values were also explored for these combinations of carbon, and sulfur compounds (pH 6-8). The highest columbic efficiency (75.8%), COD removal efficiency (86%) and voltage (667 mV) were recorded when the acetic acid was used in the MFC and the lowest columbic efficiency (12.8%), removal efficiency (37.6%) and voltage (145 mV) were observed in case of albumin. A marked increase in columbic efficiency, removal efficiency and voltage production were seen with the rise in the pH value from 6 to 8. The lowest columbic efficiency, removal efficiency and voltage production were seen at pH 6 and highest at pH 8. At each investigated pH, the highest removal efficiency, columbic efficiency, and voltage were found at substrate ratio of 20:1 while lower at 10:1. At all pH values, the carbon to nutrient ratios seemed to have followed a similar trend i.e., the COD removal efficiency, columbic efficiency and voltage generation was found in the order C:N > C:N:S > C:N:S:P > C:N:P > C:S > C:P:S > C:P. In all cases, nitrogen showed a higher removal as compared to phosphorous and sulfur.

Innovative air-cathode bioelectrochemical sensor for monitoring of total volatile fatty acids during anaerobic digestion

Bioelectrochemical sensors have proven attractive as simple and low-cost methods with high potential for online monitoring of volatile fatty acids (VFA) in the anaerobic digestion (AD) process. Herein, an innovative dual-chamber air-cathode microbial fuel cell was developed as biosensor for VFA monitoring. The response of the biosensor was nonlinear and increased along with the concentration of VFA mixture increase (2.8-112 mM). Meanwhile, the relationship was linear with low VFA levels (<14 mM) within 2-5 h reaction. High concentrations of bicarbonate decreased the voltage. Stirring speeded up the response and amplified the signal but reduced the saturation concentration (approximately 30 mM) and therefore narrowed the detection range. The applicability of the biosensor was further validated with the effluents from an AD reactor during a start-up period. The VFA concentrations measured by the biosensor were well correlated with the gas chromatographic measurement. The results demonstrate that this biosensor with a novel design could be used for VFA monitoring during the AD process. Based on the 16S rRNA gene sequencing, the dominant microbiomes in the biofilm were identified as Geobacter, Hydrogenophaga, Pelobacter, Chryseobacterium, Oryzomicrobium, and Dysgonomonas.

Promoting potential direct interspecies electron transfer (DIET) and methanogenesis with nitrogen and zinc doped carbon quantum dots

Although it has been demonstrated that one-dimensional, two-dimensional, and three-dimensional carbon nanomaterials can improve the CH₄ production of anaerobic digestion (AD), the effect of zero-dimensional carbon nanomaterials on AD have not been reported. To expand the application of carbon nanomaterials in AD, the effect of zero-dimensional carbon nanomaterials-carbon quantum dots (CDs) on various feedstocks (c.a. cellulose, glucose, ethanol, and vinegar residue) were investigated in this study. Results have shown that CH₄ yield from ethanol was increased by 24.59% (p = 0.396) after adding 5 g/L zinc doped carbon quantum dots (Zn-doped CDs) while that from vinegar residue was dramatically increased by 230% (p = 0.000) using 5 g/L nitrogen doped carbon quantum dots (N-doped CDs). In addition, photoluminescence demonstrated that CDs acted as a capacitor for transmitting and receiving electrons. Furthermore, co-occurrence network analysis revealed that Clostridiales might be used as a signal source to communicate with other species. This study firstly shifted the application of CDs from fluorescence to AD and manifested its positive impact on AD. In short, these findings provided a better understanding on the effects of CDs on different feedstocks of methanogenesis and revealed new evidence of stimulating methanogenesis via CDs.

Socio-Economic and Environmental Impacts of Biomass Valorisation: A Strategic Drive for Sustainable Bioeconomy

In the late twentieth century, the only cost-effective opportunity for waste removal cost at least several thousand dollars, but nowadays, a lot of improvement has occurred. The biomass and waste generation problems attracted concerned authorities to identify and provide environmentally friendly sustainable solutions that possess environmental and economic benefits. The present study emphasises the valorisation of biomass and waste produced by domestic and industrial sectors. Therefore, substantial research is ongoing to replace the traditional treatment methods that potentially acquire less detrimental effects. Synthetic biology can be a unique platform that invites all the relevant characters for designing and assembling an efficient program that could be useful to handle the increasing threat for human beings. In the future, these engineered methods will not only revolutionise our lives but practically lead us to get cheaper biofuels, producing bioenergy, pharmaceutics, and various biochemicals. The bioaugmentation approach concomitant with microbial fuel cells (MFC) is an example that is used to produce electricity from municipal waste, which is directly associated with the loading of waste. Beyond the traditional opportunities, herein, we have spotlighted the new advances in pertinent technology closely related to production and reduction approaches. Various integrated modern techniques and aspects related to the industrial sector are also discussed with suitable examples, including green energy and other industrially relevant products. However, many problems persist in present-day technology that requires essential efforts to handle thoroughly because significant valorisation of biomass and waste involves integrated methods for timely detection, classification, and separation. We reviewed and proposed the anticipated dispensation methods to overcome the growing stream of biomass and waste at a distinct and organisational scale.

Enhanced phenols removal and methane production with the assistance of graphene under anaerobic co-digestion conditions

Coal gasification wastewater (CGW) contains high concentration phenols which lead to poor anaerobic biodegradability and resource utilization. In this paper, new insights to improve synthetic CGW anaerobic degradation with the help of graphene under co-digestion conditions were investigated. Batch tests showed that with the addition of graphene dosage of 10 g/L and glucose as a co-substrate with chemical oxygen demand (COD) concentration of 2000 mg/L, the average COD concentration decreased from 3995 mg/L on day 1 to 983 mg/L on day 12. The average total phenol (TP) concentration decreased from 431 mg/L on day 1 to 23 mg/L on day 12. The cumulative methane production for 12 days was about 200 mL. Long-term experiments showed the average effluent COD and total phenol reached 1137 mg/L and 200 mg/L, respectively. While methane production stabilized at 500 mL/d. In addition, the coenzyme F₄₂₀ concentration increased from 1.075 μmol/g/VSS to 2.3 μmol/g/VSS. The analysis of microbial community structure indicated that the performance of phenols removal and methane production was related to the main microbial flora. The enriched Clostridium, Pseudomonas and species from Firmicutes and Chloroflexi participated in the stages of hydrolysis and acidogenesis. The electrogens Pseudomonas and archaea Methanosaeta were likely the major groups taking part in the direct interspecies electron transfer (DIET). The results obtained in this paper provide a theoretical basis for high-efficiency anaerobic degradation of CGW in practical engineering applications.

Microbial Structure and Energy Generation in Microbial Fuel Cells Powered with Waste Anaerobic Digestate

Development of economical and environment-friendly Microbial Fuel Cells (MFCs) technology should be associated with waste management. However, current knowledge regarding microbiological bases of electricity production from complex waste substrates is insufficient. In the following study, microbial composition and electricity generation were investigated in MFCs powered with waste volatile fatty acids (VFAs) from anaerobic digestion of primary sludge. Two anode sizes were tested, resulting in organic loading rates (OLRs) of 69.12 and 36.21 mg chemical oxygen demand (COD)/(g MLSS∙d) in MFC1 and MFC2, respectively. Time of MFC operation affected the microbial structure and the use of waste VFAs promoted microbial diversity. High abundance of Deftia sp. and Methanobacterium sp. characterized start-up period in MFCs. During stable operation, higher OLR in MFC1 favored growth of exoelectrogens from Rhodopseudomonas sp. (13.2%) resulting in a higher and more stable electricity production in comparison with MFC2. At a lower OLR in MFC2, the percentage of exoelectrogens in biomass decreased, while the abundance of genera Leucobacter, Frigoribacterium and Phenylobacterium increased. In turn, this efficiently decomposed complex organic substances, favoring high and stable COD removal (over 85%). Independent of the anode size, Clostridium sp. and exoelectrogens belonging to genera Desulfobulbus and Acinetobacter were abundant in MFCs powered with waste VFAs.

Enhanced volatile fatty acid production from sago hampas by Clostridium beijerinckii SR1 for bioelectricity generation using microbial fuel cells

Sago hampas is a starch-based biomass from sago processing industries consisted of 58% remaining starch. This study has demonstrated the bioconversion of sago hampas to volatile fatty acids (VFAs) by Clostridium beijerinckii SR1 via anaerobic digestion. Higher total VFAs were obtained from sago hampas (5.04 g/L and 0.287 g/g) as compared to commercial starch (5.94 g/L and 0.318 g/g). The physical factors have been investigated for the enhancement of VFAs production using one-factor-at-a-time (OFAT). The optimum condition; 3% substrate concentration, 3 g/L of yeast extract concentration and 2 g/L of ammonium nitrate enhanced the production of VFAs by 52.6%, resulted the total VFAs produced is 7.69 g/L with the VFAs yield of 0.451 g/g. VFAs hydrolysate produced successfully generated 273.4 mV of open voltage circuit and 61.5 mW/m² of power density in microbial fuel cells. It was suggested that sago hampas provide as an alternative carbon feedstock for bioelectricity generation.

TiO2 nanoparticles accelerate methanogenesis in mangrove wetlands sediment

In this study, the response of methane (CH₄) production to the addition of titanium dioxide nanoparticles (TiO₂ NPs) with three types of short-chain fatty acids (sodium acetate, sodium propionate and sodium butyrate) as carbon sources in mangrove sediment was investigated. The results showed that the maximum CH₄ formation rate increased by 45.2%, 32.7% and 48.6% and the maximum cumulative CH₄ production increased by 25.2%, 7.7% and 6.3% with the addition of TiO₂ NPs in the sodium acetate, sodium propionate and sodium butyrate systems, respectively. The microbial community analysis revealed that the electrogenic bacteria Proteiniclasticum and Pseudomonas, butyrate oxidizing bacteria Syntrophomonas and methanogens Methanobacterium and Methanosarcina were significantly enriched in the presence of TiO₂ NPs, indicating that TiO₂ NPs can enhance CH₄ production by stimulating the growth of different species of methanogens and butyrate oxidizing bacteria. The enlarged distance between microbes, the enhanced conductivity of the sediment and the typical microorganisms for direct interspecies electron transfer (DIET) with the addition of TiO₂ NPs suggest that the promoted DIET between distinct microorganisms could be another possible explanation for the improvement in CH₄ production. It can be speculated that a weaker effect on methanogenesis increases under the natural concentration of TiO₂ NPs compared with the experimental conditions; however, the amounts of TiO₂ NPs are increasing enriched in wetland environments. Therefore, the findings of this study increase current knowledge about the effect of nanomaterials on global CH₄ emissions and suggest that the discharge of wastewater containing TiO₂ NPs from the synthesis and incorporation of TiO₂ NPs in customer products needs to be monitored.

Application of slow-release carbon sources embedded in polymer for stable and extended power generation in microbial fuel cells

Stable and long-term power output is a prerequisite for the application of the energy recovered from microbial fuel cells (MFCs). In this study, a novel fuel supplying strategy based on slow-release carbon embedded in polymer gels was attempted in MFCs aimed to achieve a sustainable power generation. Polymer gels containing starch acetate as the carbon source (40% (w/w)) were prepared, and the effects of its loading dosage on power generation and microbial community structure were investigated. Results showed that the MFCs once fed with 20.0 g/L, 37.5 g/L and 55.0 g/L polymer gels attained a long-term power generation periods of 110, 140 and 170 days, respectively, with a maximum power density of 386-427 mW/m². The MFC with a medium loading dosage (37.5 g/L polymer gels) performed best. MFCs fed with the slow-release carbon enriched a distinct microbial community comparing to the control MFC with acetate as the carbon source, with the genera Geobacter, Sphaerochaeta, Christensenellaceae, Aminiphilus and Proteiniphilum significantly enriched on the anode electrode, and Sphaerochaeta, Proteiniphilum and Bacteroidetes in the anolyte. This carbon source providing method will promote the application of MFCs as a sustainable and stable power source for environmental monitoring and remediation.

Microalgae Biomass as a Potential Feedstock for the Carboxylate Platform

Volatile fatty acids (VFAs) are chemical building blocks for industries, and are mainly produced via the petrochemical pathway. However, the anaerobic fermentation (AF) process gives a potential alternative to produce these organic acids using renewable resources. For this purpose, waste streams, such as microalgae biomass, might constitute a cost-effective feedstock to obtain VFAs. The present review is intended to summarize the inherent potential of microalgae biomass for VFA production. Different strategies, such as the use of pretreatments to the inoculum and the manipulation of operational conditions (pH, temperature, organic loading rate or hydraulic retention time) to promote VFA production from different microalgae strains, are discussed. Microbial structure analysis using microalgae biomass as a substrate is pointed out in order to further comprehend the roles of bacteria and archaea in the AF process. Finally, VFA applications in different industry fields are reviewed.

Fluctuation of electrode potential based on molecular regulation induced diversity of electrogenesis behavior in multiple equilibrium microbial fuel cell

In this study, the electrogenesis behaviors and mechanisms in multiple equilibrium microbial fuel cells (MEMFCs) which volatile fatty acids as multiple electron donors are investigated. The electrochemical property and energy recovery can be enhanced in propionic acid dominant systems (HPr-D-MEMFCs) which compares to butyric acid dominant systems (HBu-D-MEMFCs), increase power density from 0.04 to 0.43 W/m² and energy recovery efficiency from 2.07 to 5.44%, respectively. With isotope experiment analysis, the fluctuation of electrode potentials induce diverse electrogenesis pathways that high utilization efficiencies and bioconversion efficiency of hybrid acids observed in HPr-D-MEMFCs which different with HAc-D-MEMFCs and HBu-D-MEMFCs. In addition, the electrochemical and microbial community variation of MEMFCs reveal that the direct interspecies electron transfer stimulated with higher electric double layer capacitance, and activities of exoelectrogens enhanced with high relative abundance in HPr-D-MEMFCs. The findings present an intensive study in electrogenesis, providing a promising way to promote energy recovery and further extend its application value.

Metallic Organic Framework-Derived Fe, N, S co-doped Carbon as a Robust Catalyst for the Oxygen Reduction Reaction in Microbial Fuel Cells

Oxygen reduction reaction (ORR) provides a vital role for microbial fuel cells (MFCs) due to its slow reaction kinetics compared with the anodic oxidation reaction. How to develop new materials with low cost, high efficacy, and eco-friendliness which could replace platinum-based electrocatalysis is a challenge that we have to resolve. In this work, we accomplished this successfully by means of a facile strategy to synthesize a metallic organic framework-derived Fe, N, S co-doped carbon with FeS as the main phase. The Fe/S@N/C-0.5 catalyst demonstrated outstandingly enhanced ORR activity in neutral PBS and alkaline media, compared to that of commercial 20% Pt-C catalyst. Here, we started-up and operated two parallel single-chamber microbial fuel cells of an air cathode, and those cathode catalysts were Fe/S@N/C-0.5 and commercial Pt-C (20% Pt), respectively. Scanning electron microscopy (SEM) elaborated that the Fe/S@N/C-0.5 composite did not change the polyhedron morphology of ZIF-8. According to X-ray diffractometry(XRD) curves, the main crystal phase of the resulted Fe/S@N/C-0.5 was FeS. The chemical environment of N, S, and Fe which are anticipated to be the high-efficiency active sites of ORR for MFCs were investigated by X-ray photoelectron spectroscopic(XPS). Nitrogen adsorption/desorption techniques were used to calculate the pore diameter distribution. In brief, the obtained Fe/S@N/C-0.5 material exhibited a pronounced reduction potential at 0.861 V (versus Reversible Hydrogen Electrode(RHE)) in 0.1M KOH solution and –0.03 V (vs. SCE) in the PBS solution, which both outperform the benchmark platinum-based catalysts. Fe/S@N/C-0.5-MFC had a higher Open Circuit Voltage(OCV) (0.71 V), stronger maximum power density (1196 mW/m2), and larger output voltage (0.47 V) than the Pt/C-MFC under the same conditions.

Three-stage anaerobic co-digestion of food waste and waste activated sludge: Identifying bacterial and methanogenic archaeal communities and their correlations with performance parameters

A three-stage anaerobic digester setup was configured and evaluated for enhanced methane production during co-digestion of food waste and waste activated sludge and the corresponding bacterial and methanogen communities were characterized. Results showed that the average methane yield (0.496 L/gVS) in the three-stage digester was 13-52% higher than that of one- and two-stage digesters. Compared to controls, an increase of 12-47% in volatile solids reduction was achieved in the three-stage digester (69.3 ± 6.7%). Bacterial phyla Proteobacteria, Firmicutes and Bacteroidetes dominated in one-, two- and three-stage digester while genera Pseudomonas, Tissierella, and Petrimonas were selectively enriched in the three-stage digester due to functional segregation. Taxonomic analysis identified 8 dominant methanogen genera, of which Methanosarcina, Methanosaeta, Methanobacterium and Methanolinea collectively accounted for 80%. With increasing OLR and digester stage number, the dominant methanogenic pathway shifted from hydrogenotrophic pattern to acetoclastic pattern and reached a final synergy of these two.

Electron donation characteristics and interplays of major volatile fatty acids from anaerobically fermented organic matters in bioelectrochemical systems

Anaerobic fermentation liquid of waste organic matters (WOMs) is rich in volatile fatty acids (VFAs), which can be treated with bioelectrochemical systems for both electrical energy recovery and organics removal. In this work, four major VFAs in the fermented WOMs supernatant were selected to examine their electron donation characteristics for power output and their complicated interplays in microbial fuel cells (MFCs). Results indicated a priority sequence of acetate, propionate, n-butyrate and i-valerate when served as the sole electron donor for electricity generation. The MFC solely fed with acetate showed the highest coulombic efficiency and power density, and the longest period for electricity production. When two of the VFAs were added with equal proportion, both acids contributed positively to electricity generation, while the selective or competitive use of substrates by diverse microorganisms behaved as an antagonism effect to prolong the degradation time of each VFA. When acetate and propionate, the preferable substrates for electricity generation, were mixed in various proportions, their large concentration difference led to improved electrical performance but decreased organic removal rate.

Electricity generation from Nopal biogas effluent using a surface modified clay cup (cantarito) microbial fuel cell

A modified clay cup (cantarito) microbial fuel cell (C-MFCs) was designed to digest the biomass effluent from a nopal biogas (NBE). To improve the process, commercial acrylic varnish (AV) was applied to the C-MFCs. The experiment was performed as:Both-C-MFCs, painting of AV on both sides of the clay cup; In-C-MFCs, painting of AV on the internal side, and Out-C-MFCs painting of AV on the external side. The order for the maximum volumetric power densities were Both-C-MFCs (1841.99 mW/m³)>Out-C-MFCs (1023.74 mW/m³) >In-C-MFCs (448.90 mW/m³). The control experiment without applied varnish did not show a stable potential, supporting the idea that the acryloyl group in varnish could favor the performance. Finally, a 4-digits clock was powered with two, Both-C-MFCs connected in series; the microbial diversity in this format was explored and a well-defined bacterial community including members of the phyla Actinobacteria, Bacteroidetes, Firmicutes, Proteobacteria, Synergistetes and candidate division TM7 was found.

Synergic degradation of 2,4,6-trichlorophenol in microbial fuel cells with intimately coupled photocatalytic-electrogenic anode

A microbial fuel cell system with intimately coupled photocatalytic-electrogenic anode (photocatalytic-MFC) was proposed for the synergetic degradation of 2,4,6-trichlorophenol (2,4,6-TCP) which has a structure of three chlorine groups connecting to a phenol ring and is well recognized as a recalcitrant pollutant for its high toxicity, bioaccumulation and persistence. The photocatalytic-electrogenic anode was prepared by coating mpg-C₃N₄ on a carbon felt anode, followed by inoculating with municipal sewage and acclimating with 2,4,6-TCP at gradient concentrations. Improved TCP degradation was achieved, showing 79.3% of TCP removal in 10 h with an original concentration of 200 mg L^-1, which was higher than that obtained with the unilluminated MFC (66.0%) and the photocatalytic-only process (56.1%). The coupled photocatalytic-electrogenic process demonstrated different degradation pathways compared with the photocatalytic-only process, with one open-chain compound (2-chloro-4-keto-2-hexenedioic acid, 2-CMA) detected in the photocatalytic-MFC system. Microbial community analysis revealed that Pseudomonas, instead of Geobacter observed in the unilluminated MFC bioanode, dominated in the photocatalytic-electrogenic anode MFC biofilm, which might be responsible for enhanced current generation in the coupled system. In addition, biofilm rich with Rhodococcus on air-cathode was also responsible for the enhanced TCP removal. This research provides an efficient strategy for the treatment of wastewater with recalcitrant contaminants by intimate-coupling of the photocatalytic and the electrogenic processes.

Two-stage pretreatment of excess sludge for electricity generation in microbial fuel cell

Thermophiles hydrolysis and acidogens fermentation were sequentially adopted to pretreat excess sludge for microbial fuel cell (MFC) electricity production. The results indicated that MFC fed with the thermophiles-acidogens pretreated sludge (MFC AB), reached a higher removal of ammonia nitrogen than the MFC fed with the heating hydrolysis and acidogens fermentation pretreated sludge (MFC NB). However, compared with the MFC AB, MFC NB presented a better performance for removal of soluble chemical oxygen demand (SCOD) (90.08%) and protein (82.42%). As for the electricity production, MFC NB obtained higher voltage of 0.632 V and maximum power density with 1.05 W/m³ while MFC AB reached maximum voltage of 0.373 V and maximum power density of 0.58 W/m³. Bacterial 16S rRNA-based molecular microbial techniques showed that microbial communities on both MFC anode biofilms was diverse and different. The cooperation of fermentation bacteria and electricigen Shewanella baltica in the MFC NB may have contributed towards the improvement of electricity generation.

Potential enhancement of direct interspecies electron transfer for anaerobic degradation of coal gasification wastewater using up-flow anaerobic sludge blanket (UASB) with nitrogen doped sewage sludge carbon assisted

Waste sewage sludge was converted into the novel conductive material of nitrogen doped sewage sludge carbon (N-SC) to enhance anaerobic degradation of coal gasification wastewater (CGW). The results indicated that N-SC played a significant role in enhanced efficiencies, with chemical oxygen demand (COD) removal efficiency increased by 25.4%, methane production rate improved by 68.1% and total volatile fatty acids (VFA) decreased by 37.5% than that of controlled reactor. The conductivity, activity of electron transport, and extracellular polymeric substances (EPS) of anaerobic sludge were remarkably enhanced with N-SC, which promoted sludge granulation and supplied better conductive environment for microorganisms. The microbial community analysis revealed that potential enhancement of direct interspecies electron transfer (DIET) was achieved by electrical connection between enriched Geobacter, Pseudomonas and Methanosaeta with N-SC assisted, which enhanced the anaerobic degradation of CGW. Moreover, anaerobic degradation with N-SC had higher capacity to resist acidic shocks, facilitating the process stability.

Enhanced methanogenic co-degradation of propionate and butyrate by anaerobic microbiome enriched on conductive carbon fibers

Recent studies have shown that the addition of conductive materials can promote direct interspecies electron transfer (DIET) between bacteria and methanoarchaea. This study demonstrated that carbon fibers could significantly stimulate methanogenic conversion of propionate and butyrate as co-substrate, while only butyrate was completely degraded in the unamended control bioreactor. In the carbon fibers-amended bioreactor, specific methane production (mL-CH₄/g COD_Initial) and methanogenesis rate (d^-1) increased by around 2.4 and 6.7 times, respectively. Various electroactive bacteria were abundant in the carbon fibers-amended bioreactor, whereas different known fermentative bacteria were abundant in the control. Moreover, carbon fibers substantially increased the abundance of Methanosaeta species. These results suggest that electroactive bacteria could be involved in DIET with Methanosaeta species enabling co-degradation of propionate and butyrate. Additionally, electrical conductivities of the biomass were comparable in both configurations, indicating that carbon fibers were the primary route for DIET.

New insights into enhanced anaerobic degradation of coal gasification wastewater (CGW) with the assistance of graphene

The up-flow anaerobic sludge blanket (UASB) system with graphene assisted was developed for coal gasification wastewater (CGW) treatment. Short-term results showed that optimal graphene addition (0.5 g/L) resulted in a more significant enhancement of methane production and chemical oxygen demand (COD) removal compared with that of the optimal activated carbon addition (10.0 g/L). Long-term results demonstrated that COD removal efficiency and methane production rate with graphene assisted achieved 64.7% and 180.5 mL/d, respectively. In addition, graphene could promote microbes accumulation and enzymes activity, resulting in higher extracellular polymeric substances (EPS) and coenzyme F₄₂₀ concentrations. X-ray Diffraction (XRD) analysis indicated that chemical of graphene changed insignificantly during the experiment. Meanwhile, with graphene assisted, cells were attached together to form microbial aggregates to facilitate sludge granulation process. Furthermore, the enriched Geobacter and Pseudomonas might perform direct interspecies electron transfer (DIET) with Methanosaeta via biological electrical connection, enhancing the anaerobic degradation of CGW.

Effects of wastewater constituents and operational conditions on the composition and dynamics of anodic microbial communities in bioelectrochemical systems

Over the last decade, there has been an ever-growing interest in bioelectrochemical systems (BES) as a sustainable technology enabling simultaneous wastewater treatment and biological production of, e.g. electricity, hydrogen, and further commodities. A key component of any BES degrading organic matter is the anode where electric current is biologically generated from the oxidation of organic compounds. The performance of BES depends on the interactions of the anodic microbial communities. To optimize the operational parameters and process design of BES a better comprehension of the microbial community dynamics and interactions at the anode is required. This paper reviews the abundance of different microorganisms in anodic biofilms and discusses their roles and possible side reactions with respect to their implications on the performance of BES utilizing wastewaters. The most important operational parameters affecting anodic microbial communities grown with wastewaters are highlighted and guidelines for controlling the composition of microbial communities are given.

Treatment of soak liquor and bioelectricity generation in dual chamber microbial fuel cell

The discharge of untreated soak liquor from tannery industry causes severe environmental pollution. This study is characterizing the soak liquor as a substrate in the microbial fuel cell (MFC) for remediation along with electricity generation. The dual chamber MFC was constructed and operated. Potassium permanganate was used as cathode solution and carbon felt electrode as anodic and cathodic material, respectively. The soak liquor was characterized by electrochemical studies viz., cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and polarization studies, respectively. The removal percentage of protein, lipid, and chemical oxygen demand (COD) were measured before and after treatment with MFC. The results of MFC showed a highest current density of 300 mA/cm² and a power density of 92 mW/m². The removal of COD, protein, and lipid were noted as 96, 81, and 97% respectively during MFC process. This MFC can be used in tannery industries for treating soak liquor and simultaneous electricity generation.

Geobacter Dominates the Inner Layers of a Stratified Biofilm on a Fluidized Anode During Brewery Wastewater Treatment

In this study, we designed a microbial electrochemical fluidized bed reactor (ME-FBR), with an electroconductive anodic bed made of activated carbon particles for treating a brewery wastewater. Under a batch operating mode, acetate and propionate consumption rates were 13-fold and 2.4-fold higher, respectively, when the fluidized anode was polarized (0.2 V) with respect to open circuit conditions. Operating in a continuous mode, this system could effectively treat the brewery effluent at organic loading rates (OLR) over 1.7 kg m^-3_NRV d^-1 and with removal efficiencies of 95 ± 1.4% (hydraulic retention time of 1 day and an influent of 1.7 g-COD L^-1). The coulombic efficiency values highly depended upon the OLR applied, and varied from a 56 ± 15% to 10 ± 1%. Fluorescence in situ hybridization (FISH) analysis revealed a relative high abundance of Geobacter species (ca. 20%), and clearly showed a natural microbial stratification. Interestingly, the Geobacter cluster was highly enriched in the innermost layers of the biofilm (thickness of 10 μm), which were in contact with the electroconductive particles of bed, whereas the rest of bacteria were located in the outermost layers. To our knowledge, this is the first time that such a clear microbial stratification has been observed on an anode-respiring biofilm. Our results revealed the relevant role of Geobacter in switching between the electrode and other microbial communities performing metabolic reactions in the outermost environment of the biofilm.

Role of acid/alkali-treatment in primary sludge anaerobic fermentation: Insights into microbial community structure, functional shifts and metabolic output by high-throughput sequencing

This study aimed to investigate the effect of acid- or alkali-treatment on volatile fatty acids (VFAs) production and microbiological mechanism during primary sludge anaerobic fermentation. Seven fermentation experiments were conducted at different pH (3-12). Results showed that the optimal pH was 10 for accumulation of VFAs. High-throughput sequencing results indicated that acid and alkali treatment could inhibit Erysipelotrichaceae_UCG-004 and norank_p_Aminicenantes, instead of promoting Pseudomonas and Tissierella at acidic and alkaline condition, respectively. Besides, molecular ecological networks (MENs) analysis and multivariate canonical correspondence analysis (CCA) revealed that the microbial community interactions are significant different between acid and alkali treatment groups, and acetic acid was the most vital factor in the distinct bacterial community assemblages. Predictive functional profiling using marker gene sequences found that amino acid transport and metabolism was the most abundant metabolic type with 8.43-9.41%, and acid- and alkali-treatment did not benefit Stickland reaction.

Boosting biomethane yield and production rate with graphene: The potential of direct interspecies electron transfer in anaerobic digestion

Interspecies electron transfer between bacteria and archaea plays a vital role in enhancing energy efficiency of anaerobic digestion (AD). Conductive carbon materials (i.e. graphene nanomaterial and activated charcoal) were assessed to enhance AD of ethanol (a key intermediate product after acidogenesis of algae). The addition of graphene (1.0g/L) resulted in the highest biomethane yield (695.0±9.1mL/g) and production rate (95.7±7.6mL/g/d), corresponding to an enhancement of 25.0% in biomethane yield and 19.5% in production rate. The ethanol degradation constant was accordingly improved by 29.1% in the presence of graphene. Microbial analyses revealed that electrogenic bacteria of Geobacter and Pseudomonas along with archaea Methanobacterium and Methanospirillum might participate in direct interspecies electron transfer (DIET). Theoretical calculations provided evidence that graphene-based DIET can sustained a much higher electron transfer flux than conventional hydrogen transfer.