Hydroxylation and hydrolysis: two main metabolic ways of spiramycin I in anaerobic digestion

Isolation, identification, and optimization of conditions for the degradation of four sulfonamide antibiotics and their metabolic pathways in Pseudomonas stutzeri strain DLY-21

Overuse of sulfonamides in aquaculture and agriculture leads to residual drugs that cause serious pollution of the environment. However, the residues of sulfonamides in the environment are not unique, and the existing microbial degradation technology has a relatively low degradation rate of sulfonamides. Therefore, in this study, a Pseudomonas stutzeri strain (DLY-21) with the ability to degrade four common SAs was screened and isolated from aerobic compost. Under optimal conditions, the DLY-21 strain degraded four sulfonamides simultaneously within 48 h, and the degradation rates were all over 90%, with the average degradation rates of SAs being sulfoxide (SDM) ≈ sulfachloropyridazine (SCP) > sulfa quinoxaline (SQ) > sulfadiazine (SQ). In addition, the main compounds of the strain DLY-21-degrading SAs were identified by LC-MS analysis. On this basis, four detailed reaction pathways for SA degradation were deduced. This is the first report of the use of a P. stutzeri strain to degrade four sulfonamide antibiotics (SQ, SDM, SCP, and SM1), which can improve the removal efficiency of sulfonamide antibiotic pollutants and thus ameliorate environmental pollution. The results showed that DLY-21 had a good degradation effect on four SAs (SQ, SDM, SCP, and SM1).

Pharmaceutical active compounds in sewage sludge: Degradation improvement and conversion into an organic amendment by bioaugmentation-composting processes

Around 143,000 chemicals find their fate in wastewater treatment plants in the European Union. Low efficiency on their removal at lab-based studies and even poorer performance at large scale experiments have been reported. Here, a coupled biological technology (bioaugmentation and composting) is proposed and proved for pharmaceutical active compounds degradation and toxicity reduction. The optimization was conducted through in situ inoculation of Penicillium oxalicum XD 3.1 and an enriched consortium (obtained from non-digested sewage sludge), into pilot scale piles of sewage sludge under real conditions. This bioaugmentation-composting system allowed a better performance of micropollutants degradation (21 % from the total pharmaceuticals detected at the beginning of the experiment) than a traditional composting process. Particularly, inoculation with P. oxalicum allowed the degradation of some recalcitrant compounds like carbamazepine, cotinine and methadone, and also produced better stabilization features in the mature compost (significant passivation of copper and zinc, higher macronutrients value, adequate physicochemical conditions for soil direct application and less toxic effect on germination) compared to the control and the enriched culture. These findings provide a feasible, alternative strategy to obtain a safer mature compost and a better removal of micropollutants performance at large scale.

Risk control of antibiotics, antibiotic resistance genes (ARGs) and antibiotic resistant bacteria (ARB) during sewage sludge treatment and disposal: A review

Sewage sludge is an important reservoir of antibiotics, antibiotic resistance genes (ARGs), and antibiotic resistant bacteria (ARB) in wastewater treatment plants (WWTPs), and the reclamation of sewage sludge potentially threats human health and environmental safety. Sludge treatment and disposal are expected to control these risks, and this review summarizes the fate and controlling efficiency of antibiotics, ARGs, and ARB in sludge involved in different processes, i.e., disintegration, anaerobic digestion, aerobic composting, drying, pyrolysis, constructed wetland, and land application. Additionally, the analysis and characterization methods of antibiotics, ARGs, and ARB in complicate sludge are reviewed, and the quantitative risk assessment approaches involved in land application are comprehensively discussed. This review benefits process optimization of sludge treatment and disposal, with regard to environmental risks control of antibiotics, ARGs, and ARB in sludge. Furthermore, current research limitations and gaps, e.g., the antibiotic resistance risk assessment in sludge-amended soil, are proposed to advance the future studies.

Global review of macrolide antibiotics in the aquatic environment: Sources, occurrence, fate, ecotoxicity, and risk assessment

The extensive use of macrolide antibiotics (MCLs) has led to their frequent detection in aquatic environments, affecting water quality and ecological health. In this study, the sources, global distribution, environmental fate, ecotoxicity and global risk assessment of MCLs were analyzed based on recently published literature. The results revealed that there are eight main sources of MCLs in the water environment. These pollution sources resulted in MCL detection at average or median concentrations of up to 3847 ng/L, and the most polluted water bodies were the receiving waters of wastewater treatment plants (WWTPs) and densely inhabited areas. Considering the environmental fate, adsorption, indirect photodegradation, and bioremoval may be the main attenuation mechanisms in natural water environments. N-demethylation, O-demethylation, sugar and side chain loss from MCL molecules were the main pathways of MCLs photodegradation. Demethylation, phosphorylation, N-oxidation, lactone ring hydrolysis, and sugar loss were the main biodegradation pathways. The median effective concentration values of MCLs for microalgae, crustaceans, fish, and invertebrates were 0.21, 39.30, 106.42, and 28.00 mg/L, respectively. MCLs induced the generation of reactive oxygen species, that caused oxidative stress to biomolecules, and affected gene expression related to photosynthesis, energy metabolism, DNA replication, and repair. Moreover, over 50% of the reported water bodies represented a medium to high risk to microalgae. Further studies on the development of tertiary treatment technologies for antibiotic removal in WWTPs, the combined ecotoxicity of antibiotic mixtures at environmental concentration levels, and the development of accurate ecological risk assessment models should be encouraged.

Enzymatic integrated in-situ advanced anaerobic digestion of sewage sludge for the removal of antibiotics and antibiotic resistance genes

Antibiotics and antibiotic resistance genes (ARGs) in sewage sludge can cause high ecotoxicological risks in the environment and public health concerns. The aims of this study were to establish enzymatic integrated in-situ advanced anaerobic digestion (AAD) by adding cellulase and papain as well as the two enzymes combined with zero valent iron (ZVI) directly into the anaerobic digesters to explore the removal of antibiotics and ARGs under the mesophilic condition (35 °C). The methane production potential during in-situ AAD was effectively improved. Papain and cellulase at 30 mg/gTSS were most effective in improving antibiotic removal. The removal of sulfamerazine (SMZ) and sulfadiazine (SMR) could reach 89.10 % and 71.75 %. Combined enzymes with ZVI also enhanced the removal of all target antibiotics, especially roxithromycin (ROX), SMZ and SMR most significantly. Except for sul1, tetA and tetB, the removal of ARGs by papain reached 6.33 %-82.15 %. The addition of cellulase effectively improved tetA removal. The combination of biological enzymes further enhanced the removal of qnrS and ermX. The tetG, tetB, sul3, ermX, ermT, qnrS, and aac(6')-IB-CR by combined enzymes with ZVI could even not be detected after digestion. Addition of papain, cellulase, and ZVI caused variations in the dominant bacteria. All target antibiotics presented significant positive correlations with the genera norank_f__Bacteroidetes_vadinHA17, norank_f__norank_o__SJA-15, norank_f__norank_o__Aminicenantales. Redundancy analysis showed archaea Methanosaeta and Candidatus_ Methanoacidiosum genera greatly contributed to antibiotics removal with the combination of enzymes and ZVI. Co-occurrence network analysis indicated the removal of ARGs was mainly based on the changes of existence of host bacteria.

Microwaves, a potential treatment for bacteria: A review

Bacteria have brought great harm to the public, especially after the emergence of multidrug-resistant bacteria. This has rendered traditional antibiotic therapy ineffective. In recent years, hyperthermia has offered new treatments to remove bacteria. Microwaves (MW) are a component of the electromagnetic spectrum and can rapidly heat materials. Taking advantage of this characteristic of MW, related studies have shown that both thermal and non-thermal effects of MW can inactivate various bacteria. Even though the understanding of MW in the field of bacteria is not sufficient for widespread use at present, MW has performed well in dealing with microorganisms and controlling infection. This review will focus on the application of MW in bacteria and discuss the advantages, prospects and challenges of using MW in the bacterial field.

Sustainable microalgal biomass valorization to bioenergy: Key challenges and future perspectives

The global trend is shifting toward circular economy systems. It is a sustainable environmental approach that sustains economic growth from the use of resources while minimizing environmental impacts. The multiple industrial use of microalgal biomass has received great attention due to its high content of essential nutrients and elements. Nevertheless, low biomass productivity, unbalanced carbon to nitrogen (C/N) ratio, resistant cellular constituents, and the high cost of microalgal harvesting represent the major obstacles for valorization of algal biomass. In recent years, microalgae biomass has been a candidate as a potential feedstock for different bioenergy generation processes with simultaneous treating wastewater and CO₂ capture. An overview of the appealing features and needed advancements is urgently essential for microalgae-derived bioenergy generation. The present review provides a timely outlook and evaluation of biomethane production from microalgal biomass and related challenges. Moreover, the biogas recovery potential from microalgal biomass through different pretreatments and synergistic anaerobic co-digestion (AcoD) with other biowastes are evaluated. In addition, the removal of micropollutants and heavy metals by microalgal cells via adsorption and bioaccumulation in their biomass is discussed. Herein, a comprehensive review is presented about a successive high-throughput for anaerobic digestion (AD) of the microalgal biomass in order to achieve for sustainable energy source. Lastly, the valorization of the digestate from AD of microalgae for agricultural reuse is highlighted.

Occurrence, fate, and persistence of emerging micropollutants in sewage sludge treatment

Sludge generated at sewage treatment plants is of environmental concern due to the voluminous production and the presence of a high concentration of emerging contaminants (ECs). This review discusses the fate of ECs in sewage sludge treatment with an emphasis on fundamental mechanisms driving the degradation of compounds based on chemical properties of the contaminant and process operating conditions. The removal of ECs in sewage sludge through various treatment processes of sludge stabilization, such as anaerobic digestion (AD), composting, and pre-treatment methods (thermal, sonication, and oxidation) followed by AD, are discussed. Several transformation mechanisms and remediation strategies for the removal of ECs in sludge are summarized. The study concludes that pH, sludge type, and the types of functional groups are the key factors affecting the sorption of ECs to sludge. During conventional waste stabilization processes such as composting, the degradation of ECs depends on the type of feedstock (TOC, N, P, C/N, C/P) and the initial concentration of the contaminant. In AD, the degree of degradation depends on the hydrophilicity of the compound. The estrogenicity of the sludge may sometimes increase due to the conversion to estrogenic compounds. The pre-treatment techniques can increase the partitioning of ECs in the soluble fraction resulting in enhanced biodegradation up to 10-60%. However, the formation of by-products and loss of OH· to scavenging under high organic content during advanced oxidation processes can make the process uneconomical and require further research.

Process type is the key driver of the fate of organic micropollutants during industrial scale treatment of organic wastes

Organic micropollutants (OMPs) such as polycyclic aromatic hydrocarbons, nonylphenols and pharmaceutical products are ubiquitous in organic wastes generated by most human activities. Those wastes are mainly recycled by land spreading, most often after treatments, such as liming, dewatering, composting or anaerobic digestion. It has been shown essentially at lab scales that biological treatments have an effect on the removal of some OMPs. However, less is known on the role of each step of industrial treatment lines combining physico-chemical and biological treatments on the OMP fate and removal. The present study focuses on the impact of waste treatment on the fate of 53 OMPs along 10 industrial treatment lines treating urban, agricultural wastes or mixtures. The combination of studying a diversity of organic wastes and of OMPs with different characteristics (solubility, ionic charges, hydrophobicity etc.), sampling in situ industrial sites, quantifying native OMP concentrations and looking at each step of complete treatment lines allows for a global and representative view of the OMP fate in the French organic waste treatment sector. Less studied wastes, i.e. territorial mixtures, revealed intermediate OMP contents and compositions, between urban and agricultural wastes. Dewatering and liming, usually dismissed, had a noticeable effect on concentrations. Anaerobic digestion and composting had significant effects on the removal of all pollutant families. Combination of processes enhanced most OMP dissipation. Here we showed for the first time that the process type rather than the waste origin affects dissipation of organic micropollutants. Such data could be used to build and validate dynamic models for the fate of OMPs on solid waste treatment plants.

Effectively remediating spiramycin from production wastewater through hydrolyzing its functional groups using solid superacid TiO2/SO4

Breaking down the structural bonds and eliminating the functional groups are more efficient than destroying the whole molecule in antibiotic production wastewater (APW) pretreatment before further biotreatment. Two sulfated titania (TiO₂/SO₄) solid superacids, SSA1 and SSA2 were synthesized, characterized and used for hydrolytic pretreatment of spiramycin in APW. Spiramycin removal followed an order of SSA2>SSA1>TiO₂≈pH = 3>control. The hydrolytic efficiencies increased at elevated temperature from 25 °C to 65 °C. The hydrolytic kinetics followed a first-order model and SSA2 performed the fastest. The performances were positively correlated with both the total acidity determined by n-butylamine titration and the strength of acid sites measured by NH₃-temperature-programmed desorption (TPD). The residual solution for SSA2 presented the least antibacterial potency and anaerobic inhibition among all treatments. The hydrolyzed product was identified as the m/z 699.4321 fragment using UPLC-Q/TOF-MS, which was formed after losing a functional mycarose moiety from the parent molecular. The solid superacids were effective in selectively eliminating 433 mg/L of spiramycin and the antibacterial potencies of the spiramycin production wastewater, which contained very high concentrations of COD (33,000 mg/L). This hydrolytic method avoids using and handling hazardous and corrosive mineral acids on site. It is attractive as a selective catalytic pretreatment method to cleave antibiotics' functional groups and to reduce its inhibitory effects before sequential biotreatments.

Rapid thermal-acid hydrolysis of spiramycin by silicotungstic acid under microwave irradiation

Spiramycin is a widely used macrolide antibiotic and exists at high concentration in production wastewater. A thermal-acid hydrolytic pretreatment using silicotungstic acid (STA) under microwave (MW) irradiation was suggested to mitigate spiramycin from production wastewater. Positive correlations were observed between STA dosage, MW power, interaction time and the hydrolytic removal efficiencies, and an integrative equation was generalized quantitively. Rapid and complete removal 100 mg/L of spiramycin was achieved after 8 min of reaction with 1.0 g/L of STA under 200 W of MW irradiation, comparing to 30.1% by MW irradiation or 15.9% by STA alone. The synergetic effects of STA and MW irradiation were originated from the dissociated-proton catalysis by STA and the dipolar rotation heating effect of MW. STA performed much better than the mineral acid H₂SO₄ under MW, due to the much stronger Brönsted acidity and higher Hammett acidity. After 8 min, 98.0% of antibacterial potency was also reduced. The m/z 558.8614 fragment (P1) and m/z 448.1323 fragment (P2) were identified as the primary products, which were formed by breaking glucosidic bonds and losing mycarose and forosamine for P1 and further mycaminose moiety for P2. Finally, production wastewater with 433 mg/L of spiramycin was effectively treated using this thermal-acid hydrolytic method. Spiramycin and its antibacterial potency both dropped to 0 after 6 min. The potency drop was supposed from the losing of mycarose and/or forosamine. To decrease both the concentration of spiramycin and its antibacterial potency, combinedly using STA and MW was suggested in this work to break down the structural bonds of the functional groups rather than to destroy the whole antibiotic molecules. It is promising for pretreating spiramycin-contained production wastewater to mitigate both the antibiotic and its antibacterial potency.

Variation of antibiotics in sludge pretreatment and anaerobic digestion processes: Degradation and solid-liquid distribution

Degradation and solid-liquid distribution of antibiotics in three sludge pretreatments (ultrasonic, alkaline and thermal hydrolysis pretreatment) and subsequent anaerobic digestion processes were investigated. The contamination of fluoroquinolones (FQs) was most serious in the raw sludge, while sulfonamides (SAs) were negligible. Obvious solubilization of antibiotics was observed after sludge pretreatments. The intracellular antibiotics were released after thermal hydrolysis pretreatment, meanwhile tetracyclines (TCs) were thermally decomposed. Compared to TCs and macrolides (MLs), FQs were hardly degraded in anaerobic digestion with removal efficiencies lower than 42.02%, and the residual FQs were mostly adsorbed on the digested sludge. The limiting step for FQs reduction was the biodegradation, rather than desorption of adsorbed antibiotics. Addition of pretreatments had no obvious effect on the degradation and distribution of antibiotics in the anaerobic digested sludge, except that the thermal hydrolysis enhanced the migration of antibiotics to the liquid phase.

Anaerobic biodegradation of spiramycin I and characterization of its new metabolites

Activated sludge was used to treat the wastewater containing spiramycin I. Three new metabolites were isolated and identified, which produced by oxidation of C6-aldehyde, hydrolysis of C5-mycaminose-mycarose and macrolactone ring-open reaction of spiramycin I in anaerobic digestion. And their antimicrobial activities were inactivated. Our results indicated that anaerobic biodegradation metabolites of spiramycin I could not induce bacterial resistance in environment.