Influence of lignin addition on the enzymatic digestibility of pretreated lignocellulosic biomasses

Synergism of jet milling and deep eutectic solvent pretreatment on grapevine lignin fractionation and enhancing enzymatic hydrolysis

Herein, we investigated the synergistic effects of jet milling (JM) and deep eutectic solvent (DES) pretreatment on the fractionation of grapevine lignin and the consequent enhancement of enzymatic hydrolysis. Grapevine, a substantial byproduct of the wine industry, was subjected to JM pretreatment to produce finely powdered particles (median diameter D50 = 98.90), which were then further treated with acidic ChCl-LA and alkaline K2CO3-EG DESs. The results revealed that the combined JM + ChCl-LA pretreatment significantly increased the cellulose preservation under optimal conditions (110 °C, 4 h, and 20 % water content), achieving removal rates of 74.18 % xylan and 66.05 % lignin, respectively. The pretreatment temperature and inhibitor production were reduced, resulting in a remarkable threefold increase in glucose yield compared to untreated samples. Moreover, the structural analysis of the pretreated lignin indicated an enrichment of phenolic units, leading to enhanced antioxidant and antibacterial activities, particularly in the JM pretreated samples. These findings underscore the promising potential of the synergistic JM and DES pretreatment in facilitating the efficient utilization of grapevine lignocellulosic biomass for sustainable biorefinery technologies.

Achieving high enzymatic hydrolysis sugar yield of sodium hydroxide-pretreated wheat straw with a low cellulase dosage by adding sulfomethylated tannic acid

Sulfonated lignin can significantly enhance the enzymatic hydrolysis of lignocellulose substrates. Lignin is a type of polyphenol, therefore, sulfonated polyphenol, such as tannic acid, is likely to have similar effects. In order to obtain a low-cost and high-efficiency additive to improve enzymatic hydrolysis, sulfomethylated tannic acids (STAs) with different sulfonation degrees were prepared and their impact on enzymatic saccharification of sodium hydroxide-pretreated wheat straw were investigated. Tannic acid strongly inhibited, while STAs strongly promoted the substrate enzymatic digestibility. While adding 0.04 g/g-substrate STA containing 2.4 mmol/g sulfonate group, the glucose yield increased from 60.6% to 97.9% at a low cellulase dosage (5 FPU/g-glucan). The concentration of protein in enzymatic hydrolysate significantly increased with the added STAs, indicating that cellulase preferentially adsorbed with STAs, thereby reducing the amount of cellulase nonproductively anchored on substrate lignin. This result provides a reliable approach for establishing an efficient lignocellulosic enzyme hydrolysis system.

Employing Cationic Kraft Lignin as Additive to Enhance Enzymatic Hydrolysis of Corn Stalk

A water-soluble cationic kraft lignin (named JLQKL₅₀), synthesized by combining quaternization and crosslinking reactions, was used as an additive to enhance the enzymatic hydrolysis of dilute-alkali-pretreated corn stalk. The chemical constitution of JLQKL₅₀ was investigated by Fourier transform infrared spectroscopy, ¹H nuclear magnetic resonance (NMR) and ¹³C NMR spectroscopy, and elemental analysis. The enzymatic hydrolysis efficiency of corn stalk at solid content of 10% (w/v) was significantly improved from 70.67% to 78.88% after 24 h when JLQKL₅₀ was added at a concentration of 2 g/L. Meanwhile, the enzymatic hydrolysis efficiency after 72 h reached 91.11% with 10 FPU/g of cellulase and 97.92% with 15 FPU/g of cellulase. In addition, JLQKL₅₀ was found capable of extending the pH and temperature ranges of enzymatic hydrolysis to maintain high efficiency (higher than 70%). The decrease in cellulase activity under vigorous stirring with the addition of JLQKL₅₀ was 17.4%, which was much lower than that (29.7%) without JLQKL₅₀. The addition of JLQKL₅₀ reduced the nonproductive adsorption of cellulase on the lignin substrate and improved the longevity, dispersity, and stability of the cellulase by enabling electrostatic repulsion. Therefore, the enzymatic hydrolysis of the corn stalk was enhanced. This study paves the way for the design of sustainable lignin-based additives to boost the enzymatic hydrolysis of lignocellulosic biomass.

Exploring how lignin structure influences the interaction between carbohydrate-binding module and lignin using AFM

Nonproductive adsorption of cellulase onto the residual lignin in substrate seriously hinders the enzymatic hydrolysis. To understand how lignin structure affects lignin-cellulase interaction, the carbohydrate-binding module (CBM) functionalized atomic force microscope tip was used to measure CBM-lignin interaction by single-molecule dynamic force spectroscopy in this work. The results showed that sulfonated lignin (SL) has the greatest adhesion force to CBM (4.74 nN), while those of masson pine milled wood lignin (MWL), poplar MWL and herbaceous MWLs were 2.85, 1.03 and 0.27-0.61 nN, respectively. It provides direct quantitative evidence for the significance of lignin structure on lignin-cellulase interaction. The CBM-MWLs interaction decreased sharply to 0.054-0.083 nN while SL was added, indicating the primary mechanism of SL promoting lignocellulose hydrolysis was significantly reducing the nonproductive adsorption of substrate lignin on cellulase. Finally, the "competitive adsorption" mechanism was proposed to interpret why SL effectively promotes the enzymatic hydrolysis of lignin-containing substrates.

Lignin-Based Materials for Additive Manufacturing: Chemistry, Processing, Structures, Properties, and Applications

The utilization of lignin, the most abundant aromatic biomass component, is at the forefront of sustainable engineering, energy, and environment research, where its abundance and low-cost features enable widespread application. Constructing lignin into material parts with controlled and desired macro- and microstructures and properties via additive manufacturing has been recognized as a promising technology and paves the way to the practical application of lignin. Considering the rapid development and significant progress recently achieved in this field, a comprehensive and critical review and outlook on three-dimensional (3D) printing of lignin is highly desirable. This article fulfils this demand with an overview on the structure of lignin and presents the state-of-the-art of 3D printing of pristine lignin and lignin-based composites, and highlights the key challenges. It is attempted to deliver better fundamental understanding of the impacts of morphology, microstructure, physical, chemical, and biological modifications, and composition/hybrids on the rheological behavior of lignin/polymer blends, as well as, on the mechanical, physical, and chemical performance of the 3D printed lignin-based materials. The main points toward future developments involve hybrid manufacturing, in situ polymerization, and surface tension or energy driven molecular segregation are also elaborated and discussed to promote the high-value utilization of lignin.

Enzymatic saccharification promotion for bioenergy poplar under green liquor pretreatment by fully sulfonated polystyrene: Effect of molecular weight

Water-soluble lignin and lignin derivatives are cited to promote the enzymatic saccharification of lignocellulose. Herein, a series of fully sulfonated polystyrene sulfonates (FSPSSs) with various molecular weights (MW) were synthesized through free radical polymerization (FRP) and atom transfer radical polymerization (ATRP) to serve as lignin analogues to boost the enzymatic saccharification of bioenergy poplar under green liquor pretreatment. The FRP-made polymers with MW 944.5 × 10³ to 123.6 × 10³ g/mol increased the enzymatic hydrolysis digestibility (SED) by 13 % to 18.8 %. On contrary, the ATRP-made polymers with lower MW (3.8 × 10³-12.2 × 10³ g/mol) showed a weak effect with<8 % improvement in SED. This can be explained the adsorption capacity and the conformation of cellulase-FSPSS complexes, which respond to the reducing nonproductive adsorption correlated to their MWs, due to the strong dependence of molecular conformation on the chain length of strong polyelectrolytes.

Improve Enzymatic Hydrolysis of Lignocellulosic Biomass by Modifying Lignin Structure via Sulfite Pretreatment and Using Lignin Blockers

Even traditional pretreatments can partially remove or degrade lignin and hemicellulose from lignocellulosic biomass for enhancing its enzymatic digestibility, the remaining lignin in pretreated biomass still restricts its enzymatic hydrolysis by limiting cellulose accessibility and lignin-enzyme nonproductive interaction. Therefore, many pretreatments that can modify lignin structure in a unique way and approaches to block the lignin’s adverse impact have been proposed to directly improve the enzymatic digestibility of pretreated biomass. In this review, recent development in sulfite pretreatment that can transform the native lignin into lignosulfonate and subsequently enhance saccharification of pretreated biomass under certain conditions was summarized. In addition, we also reviewed the approaches of the addition of reactive agents to block the lignin’s reactive sites and limit the cellulase-enzyme adsorption during hydrolysis. It is our hope that this summary can provide a guideline for workers engaged in biorefining for the goal of reaching high enzymatic digestibility of lignocellulose.

Lignin fractionation to realize the comprehensive elucidation of structure-inhibition relationship of lignins in enzymatic hydrolysis

A better understanding of the relationship between lignin structures and their inhibitory effects in enzymatic saccharification would facilitate the development of lignocellulose biorefinery process. However, the heterogeneity of lignins challenges the elucidation of lignin structure-inhibition correlation. In this study, two types of lignin fractions including ethanol soluble lignins and ethanol insoluble lignins were respectively isolated from the poplars pretreated with various severities. The impacts of pretreatment severities on the structural changes of lignin fractions were studied from the perspective of inter-units linkages, condensed aromatic substructure, and hydroxyl groups. Furthermore, it was observed that lignin addition strongly inhibited the enzymatic saccharification of pure cellulose by 13.3 ∼ 56.3%. Lignin inhibition extents were increased with the elevated pretreatment severity. The relationships between the lignin structural features and lignin inhibition were analyzed, which revealed that the contents of condensed aromatic units and phenolic hydroxyl were crucial factors determining the lignin inhibition.

Structural Changes of Alkali Lignin under Ozone Treatment and Effect of Ozone-Oxidized Alkali Lignin on Cellulose Digestibility

In this study, the structural changes of alkali lignin induced by ozonation were investigated, and the effect of ozone-treated alkali lignin and its mechanism on Avicel enzymatic hydrolysis was examined. The physicochemical properties of alkali lignin were analyzed by FTIR, 1H-13C HSQC NMR, and GPC. It was revealed that ozone pretreatment increased the content of carboxyl and/or aldehyde groups and the negative zeta potential of alkali lignin, which enhanced the electrostatic repulsion between alkali lignin and cellulase; The S/G ratio was reduced, indicating the hydrophobic interaction was diminished. The Langmuir adsorption isotherm showed that the cellulase binding strength of ozone pretreated alkali lignin (OL-pH3, OL-pH7, and OL-pH12 were 16.67, 13.87, and 44.05 mL/g, respectively) was significantly lower than that of alkali lignin (161.29 mL/g). The 72 h hydrolysis yields of Avicel added with OL-pH3, OL-pH7, and OL-pH12 were 55.4%, 58.6%, and 54.9% respectively, which were 2.6–6.3% higher than that of Avicel added with AL (52.3%). This research aimed to reduce the non-productive adsorption between cellulase and lignin by investigating the structural changes of lignin caused by ozone treatment. For the first time, we discovered that ozone-treated alkali lignin has a further promotion effect on the enzymatic digestion of cellulose, providing a green and feasible pretreatment process for the enzymatic hydrolysis of lignocellulose and aiding in the more efficient utilization of biomass.

Polystyrene sulfonate is effective for enhancing biomass enzymatic saccharification under green liquor pretreatment in bioenergy poplar

BACKGROUND

Water-soluble lignin (particularly lignosulfonate, LS) has been well documented for its significance on enzymatic saccharification of lignocellulose, though the promotion mechanism has not been fully understood. Much attention has been paid to natural lignin or its derivatives. The disadvantage of using natural lignin-based polymers as promoting agents lies in the difficulty in tailor-incorporating functional groups due to their complex 3D structures. To further improve our understanding on the promotion mechanism of water-soluble lignin in the bioconversion of lignocellulose and to pursue better alternatives with different skeleton structures other than natural lignin, herein we reported a synthetic soluble linear aromatic polymer, sodium polystyrene sulfonate (PSS), to mimic LS for enhancing the efficiency of enzymatic saccharification.

RESULTS

The role of PSS in enzymatic saccharification of pure cellulose and green liquor-pretreated poplar (GL-P) was explored by analyzing substrate enzymatic digestibility (SED) under different addition dosages and various pH media, along with LS for comparison. At the cellulase loading of 13.3 FPU/g-glucan, the glucose yield of GL-P increased from 53% for the control to 81.5% with PSS addition of 0.1 g/g-substrate. It outperformed LS with the addition of 0.2 g/g-substrate by 6.3%. In the pH range from 4.5 to 6, PSS showed a positive effect on lignocellulose saccharification with the optimum pH at 4.8, where the most pronounced SED of GL-P was achieved. The underlying mechanism was unveiled by measuring zeta potential and using Quartz Crystal Microbalance (QCM) and Multi-parametric Surface Plasmon Resonance (MP-SPR). The results confirmed that the complexes of cellulase and PSS were conjugated and the negatively supercharged complexes reduced non-productive binding effectively along with the improved saccharification efficiency. The thickness of PSS required to block the binding sites of cellulase film was less than half of that of LS, and the PSS adlayer on cellulase film is also more hydrated and with a much lower shear modulus than LS adlayer.

CONCLUSIONS

PSS as LS analogue is effective for enhancing the biomass enzymatic saccharification of GL-pretreated poplar. PSS exhibited a severer inhibition on the enzymatic saccharification of pure cellulose, while a more positive effect on bioconversion of lignocellulose (GL-P) than LS. In addition, a much lower dosage is required by PSS. The dynamic enzymatic hydrolysis indicated PSS could prolong the processive activity of cellulase. The valid data stemmed from QCM and SPR expressed that PSS bound to cellulases and the as-formed complexes reduced the non-productive adsorption of cellulase onto substrate lignin more efficiently than LS due to its flexible skeleton and highly hydrated structure. Therefore, PSS is a promising alternative promoting agent for lignocellulose saccharification. From another perspective, the synthetic lignin mimics with controllable structures enable us to reach an in-depth understanding of the promotion mechanism of soluble lignins on enzymatic saccharification.

Current understanding and optimization strategies for efficient lignin-enzyme interaction: A review

From energy perspective, with abundant polysaccharides (45-85%), the renewable lignocellulosic is recognized as the 2nd generation feedstock for bioethanol and bio-based products production. Enzymatic hydrolysis is a critical pathway to yield fermentable monosaccharides from pretreated substrates of lignocellulose. Nevertheless, the lignin presence in lignocellulosic substrates leads to the low substrate enzymatic digestibility ascribed to the nonproductive adsorption. It has been reported that the water-soluble lignin (low molecular weight, sulfonated/sulfomethylated and graft polymer) enhance the rate of enzymatic digestibility, however, the catalytic mechanism of lignin-enzyme interaction remains elusive. In this review, optimization strategies for enzymatic hydrolysis based on the lignin structural modification, enzyme engineering, and different additives are critically reviewed. Lignin-enzyme interaction mechanism is also discussed (lignin and various cellulases). In addition, the mathematical models and simulation of lignin, cellulose and enzyme aims for promoting an integrated biomass-conversion process for sustainable production of value-added biofuels.

Comparison of sulfomethylated lignin from poplar and masson pine on cellulase adsorption and the enzymatic hydrolysis of wheat straw

In this work, effects of sulfomethylated lignins (SLs) prepared from masson pine (SL_M) and poplar (SL_P) on enzymatic hydrolysis and cellulase-lignin interaction were comparatively investigated. The results showed that both SL_M and SL_P significantly promoted the substrate enzymatic digestibility. The total sugar yield increased from 38.6% to 74.4% and ∼ 100%, respectively at 10 FPU/g-cellulose of cellulase dosage. The protein content in hydrolysate linearly increased with the addition of SL (0 - 1.6 g/g-substrate lignin), which suggested the competitive adsorption of cellulase may occur to substrate lignin and SLs. Further structural analysis of lignin revealed the high S/(V + H) ratio was directly related to the high enzymatic saccharification efficiency. The strong interaction between SL and cellulase decreased the nonproductive adsorption of cellulase onto substrate lignin and increased the accessibility of cellulase to carbohydrate, which was considered to be the key factor for the improvement of substrate enzymatic digestibility.

Biological Activities and Emerging Roles of Lignin and Lignin-Based Products─A Review

Bioactive substances, displaying excellent biocompatibility, chemical stability, and processability, could be extensively applied in biomedicine and tissue engineering. In recent years, plant-based bioactive substances such as flavonoids, vitamins, terpenes, and lignin have received considerable attention due to their human health benefits and pharmaceutical/medical applications. Among them is lignin, an amorphous biomacromolecule mainly derived from the combinatorial radical coupling of three phenylpropane units (p-hydroxypenyl, guaiacyl, and syringyl) during lignification. Lignin possesses intrinsic bioactivities (antioxidative, antibacterial, anti-UV activities, etc.) against phytopathogens. Lignin also enhances the plant resistance (adaptability) against environmental stresses. The abundant structural features of lignin offer other significant bioactivities including antitumor and antivirus bioactivities, regulation of plant growth, and enzymatic hydrolysis of cellulose. This Review reports the latest research results on the bioactive potential of lignin and lignin-based substances in biomedicine, agriculture, and biomass conversion. Moreover, the interfacial reactions and bonding mechanisms of lignin with biotissue/cells and other constituents were also discussed, aiming at promoting the conversion or evolution of lignin from industrial wastes to value-added bioactive materials.

Recent advances in understanding the effects of lignin structural characteristics on enzymatic hydrolysis

Enzymatic hydrolysis of lignocellulose for bioethanol production shows a great potential to remit the rapid consumption of fossil fuels, given the fact that lignocellulose feedstocks are abundant, cost-efficient, and renewable. Lignin results in low enzymatic saccharification by forming the steric hindrance, non-productive adsorption of cellulase onto lignin, and deactivating the cellulase. In general, the non-productive binding of cellulase on lignin is widely known as the major cause for inhibiting the enzymatic hydrolysis. Pretreatment is an effective way to remove lignin and improve the enzymatic digestibility of lignocellulose. Along with removing lignin, the pretreatment can modify the lignin structure, which significantly affects the non-productive adsorption of cellulase onto lignin. To relieve the inhibitory effect of lignin on enzymatic hydrolysis, enormous efforts have been made to elucidate the correlation of lignin structure with lignin-enzyme interactions but with different views. In addition, contrary to the traditional belief that lignin inhibits enzymatic hydrolysis, in recent years, the addition of water-soluble lignin such as lignosulfonate or low molecular-weight lignin exerts a positive effect on enzymatic hydrolysis, which gives a new insight into the lignin-enzyme interactions. For throwing light on their structure-interaction relationship during enzymatic hydrolysis, the effect of residual lignin in substrate and introduced lignin in hydrolysate on enzymatic hydrolysis are critically reviewed, aiming at realizing the targeted regulation of lignin structure for improving the saccharification of lignocellulose. The review is also focused on exploring the lignin-enzyme interactions to mitigate the negative impact of lignin and reducing the cost of enzymatic hydrolysis of lignocellulose.

Strategies towards Reduction of Cellulases Consumption: Debottlenecking the Economics of Lignocellulosics Valorization Processes

Lignocellulosic residues have been receiving growing interest as a promising source of polysaccharides, which can be converted into a variety of compounds, ranging from biofuels to bioplastics. Most of these can replace equivalent products traditionally originated from petroleum, hence representing an important environmental advantage. Lignocellulosic materials are theoretically unlimited, cheaper and may not compete with food crops. However, the conversion of these materials to simpler sugars usually requires cellulolytic enzymes. Being still associated with a high cost of production, cellulases are commonly considered as one of the main obstacles in the economic valorization of lignocellulosics. This work provides a brief overview of some of the most studied strategies that can allow an important reduction of cellulases consumption, hence improving the economy of lignocellulosics conversion. Cellulases recycling is initially discussed regarding the main processes to recover active enzymes and the most important factors that may affect enzyme recyclability. Similarly, the potential of enzyme immobilization is analyzed with a special focus on the contributions that some elements of the process can offer for prolonged times of operation and improved enzyme stability and robustness. Finally, the emergent concept of consolidated bioprocessing (CBP) is also described in the particular context of a potential reduction of cellulases consumption.

On the Feasibility of a pMDI-Reduced Production of Wood Fiber Insulation Boards by Means of Kraft Lignin and Ligneous Canola Hulls

The thermal insulation of buildings using wood fiber insulation boards (WFIBs) constitutes a positive contribution towards climate change. Thereby, the bonding of wood fibers using mainly petrochemical-based resins such as polymeric diphenylmethane diisocyanate (pMDI) is an important measure to meet required board properties. Still there is a need to reduce or partial substitute the amount of these kinds of resins in favor of a greener product. This study therefore focusses on the feasibility of reducing the amount of pMDI by 50% through the addition of 1% BioPiva 395 or Indulin as two types of softwood Kraft-Lignin and lignin rich canola hulls together with propylene carbonate as a diluent. A panel density of 160 kg/m³ and a thickness of 40 mm was aimed. The curing of these modified pMDI was investigated by using two types of techniques: hot-steam (HS) and innovative hot-air/hot-steam-process (HA/HS). The WFIBs were then tested on their physical-mechanical properties. The equilibrium moisture content (EMC) was determined at two different climates. An exemplary investigation of thermal conductivity was conducted as well. The WFIBs did undergo a further chemically based analysis towards extractives content and elemental (C, N) composition. The results show that it is feasible to produce WFIBs with lower quantities of pMDI resin and added lignin with enhanced physical-mechanical board properties, which were lacking no disadvantages towards thermal conductivity or behavior towards moisture, especially when cured via HA/HS-process.

Role of laccase gene in wheat NILs differing at QTL-Fhb1 for resistance against Fusarium head blight

Fusarium head blight (FHB), caused mainly by Fusarium graminearum (Fg), is one of the most severe diseases of wheat. It affects grain yield and quality due to mycotoxin contamination, which is harmful for both human and livestock consumption. Cell wall lignification, following pathogen invasion, is one of the innate defense responses. Plant laccases are known to lignify the secondary cell walls. A metabolo-genomics study identified laccase as one of the candidate genes in QTL-Fhb1 of wheat NILs derived from Sumai 3*5/Thatcher cross. Based on phylogenetics, it was named as TaLAC4. Real-time qPCR revealed a strongly induced expression of TaLAC4 in NIL-R. The VIGS based transient silencing of TaLAC4 in NIL-R resulted in an increased susceptibility leading to Fg spread within the entire spike in 15dpi, contrasting to non-silenced where the infection was limited to inoculated spikelets. Histopathology revealed thickened cell walls, mainly due to G-lignin, in non-silenced NIL-R, relative to silenced, in conjunction with higher total lignin content. Metabolic profiling of TaLAC4 silenced NILs identified the accumulation of several precursor metabolites higher in abundances upstream TaLAC4. These results confirm that the resistance function of TaLAC4 in NIL-R is due to pathogen-induced lignification of secondary cell walls in the rachis.

Key process parameters for deep eutectic solvents pretreatment of lignocellulosic biomass materials: A review

Deep eutectic solvent (DES) has been considered as a novel green solvent for lignocellulosic biomass pretreatment. The efficiency of DES pretreatment is affected by the synergy of various process parameters. The study of effect of DES physicochemical properties and pretreatment reaction conditions on the mechanism of lignocellulose biomass fractionation was of great significance for the development of biomass conversion. Form the view of process control, this review summarized recent advances in DES pretreatment, analyzed the challenges, and prospected the future development of this research field.

Nanocellulose Production: Exploring the Enzymatic Route and Residues of Pulp and Paper Industry

Increasing environmental and sustainability concerns, caused by current population growth, has promoted a raising utilization of renewable bio-resources for the production of materials and energy. Recently, nanocellulose (NC) has been receiving great attention due to its many attractive features such as non-toxic nature, biocompatibility, and biodegradability, associated with its mechanical properties and those related to its nanoscale, emerging as a promising material in many sectors, namely packaging, regenerative medicine, and electronics, among others. Nanofibers and nanocrystals, derived from cellulose sources, have been mainly produced by mechanical and chemical treatments; however, the use of cellulases to obtain NC attracted much attention due to their environmentally friendly character. This review presents an overview of general concepts in NC production. Especial emphasis is given to enzymatic hydrolysis processes using cellulases and the utilization of pulp and paper industry residues. Integrated process for the production of NC and other high-value products through enzymatic hydrolysis is also approached. Major challenges found in this context are discussed along with its properties, potential application, and future perspectives of the use of enzymatic hydrolysis as a pretreatment in the scale-up of NC production.

Lignin extracted by γ-valerolactone/water from corn stover improves cellulose enzymatic hydrolysis

The impact of lignin extracted from γ-valerolactone/water (GVL/H₂O) pretreatment of corn stover on the enzymatic hydrolysis of cellulose was investigated. Two lignin samples were separated and named as GL25 and GL75 according to the amounts of sulfuric acid (25 mM and 75 mM) used in the GVL/H₂O pretreatment. With the addition of 2 g/L of GL25 and GL75, the glucan conversion of enzymatic hydrolysis of Avicel improved markedly from 28.0% to 37.4% and 31.3%, respectively. Moreover, the improvement of glucan conversion increased when increasing the loadings of GL25 and GL75. A similar observation was made when GVL/H₂O pretreated corn stover was the substrate. The results of the cellulase adsorption experiments showed that the GLs had a lower maximum cellulase adsorption capacity and binding strength compared to that of acid-insoluble lignin. Further structural characterization of the GLs revealed that they had a low zeta-potential and hydrophobicity, but a high Syringyl/Guaiacyl ratio.

The critical role of lignin in lignocellulosic biomass conversion and recent pretreatment strategies: A comprehensive review

Heterogeneity and rigidity of lignocellulose causing resistance to its deconstruction have provided technical and economic challenges in the current biomass conversion processes. Lignin has been considered as a crucial recalcitrance component in biomass utilization. An in-depth understanding of lignin properties and their influences on biomass conversion can provide clues to improve biomass utilization. Also, utilization of lignin can significantly increase the economic viability of biorefinery. Recent lignin-targeting pretreatments have aimed not only to overcome recalcitrance for biomass conversion but also to selectively fractionate lignin for lignin valorization. Numerous studies have been conducted in biomass characteristics and conversion technologies, and the role of lignin is critical for lignin valorization and biomass pretreatment development. This review provides a comprehensive review of lignin-related biomass characteristics, the impact of lignin on the biological conversion of biomass, and recent lignin-targeting pretreatment strategies. The desired lignin properties in biorefinery and future pretreatment directions are also discussed.

Improving enzymatic hydrolysis of acid-pretreated bamboo residues using amphiphilic surfactant derived from dehydroabietic acid

In this work, amphiphilic surfactant was obtained using dehydroabietic acid from pine rosin and then pre-adsorbed with acid-pretreated bamboo residues (AP-BR) to block the residual lignin adsorption site, which is expected to improve its enzymatic digestibility. Results from cryogenic-transmission electron microscopy (Cryo-TEM) indicated amphiphilic surfactant with PEG with polymerization degree of 34 (D-34) aggregated to form worm-like micelles, which improved enzymatic hydrolysis yield of AP-BR from 24.3% to 71.9% by pre-adsorbing with 0.8 g/L. Amphiphilic surfactants pre-adsorbed on AP-BR could reduce hydrophobicity of AP-BR, adsorption affinity and adsorption capacity of lignin for cellulase from 0.51 L/g to 0.48-0.32 L/g, from 2.9 mL/mg to 1.8-1.4 mL/mg, and from 122.3 mg/g to 101.9-21.4 mg/g, respectively. These changed properties showed compelling positive contributions (R² > 0.9) for free enzymes in the supernatants and sequently for final enzymatic hydrolysis yield, which was caused by blocking non-productively hydrophobic adsorption between lignin and cellulase.

Lignin Redistribution for Enhancing Barrier Properties of Cellulose-Based Materials

Renewable cellulose-based materials have gained increasing interest in food packaging because of its favorable biodegradability and biocompatibility, whereas the barrier properties of hydrophilic and porous fibers are inadequate for most applications. Exploration of lignin redistribution for enhancing barrier properties of paper packaging material was carried out in this work. The redistribution of nanolized alkali lignin on paper surface showed excellent water, grease, and water vapor barrier. It provided persisted water (contact angle decrease rate at 0.05°/s) and grease (stained area undetectable at 72 h) resistance under long-term moisture or oil direct contact conditions, which also inhibited the bacterial growth to certain degree. Tough water vapor transmission rate can be lowered 82% from 528 to 97 g/m2/d by lignin redistribution. The result suggests that alkali lignin, with multiple barrier properties, has great potential in bio-based application considering the biodegradability, biocompatibility, and recyclability.

Effect of Enzyme Interaction with Lignin Isolated from Pretreated Miscanthus x gigantues on Cellulolytic Efficiency

The effect of binding between the lignin isolates from an alkali (NaOH)– and an acid (H2SO4)– pretreated Miscanthus and cellulolytic enzymes in Cellic® CTec2 was investigated. Additonally, cellobiose and Avicel were enzymatically hydrolyzed with and without lignin isolates to study how enzyme binding onto lignin affects its conversion to glucose. Three carbohydrate–lignin loadings (0.5:0.25, 0.5:0.5, and 0.5:1.0% (w/v)) were employed. The results indicated that β-glucosidase (BG) had a strong tendency to bind to all lignin isolates. The overall tendency of enzyme binding onto lignin isolate was similar regardless of pretreatment chemical concentration. Though enzyme binding onto lignin isolates was observed, hydrolysis in the presence of these isolates did not have a significant (p > 0.05) impact on glucose production from cellobiose and Avicel. Cellobiose to glucose conversion of 99% was achieved via hydrolysis at both 5 and 10 FPU/g carbohydrate. Hydrolysis of Avicel with 5 and 10 FPU/g CTec2 resulted in 29.3 and 47.7% conversion to glucose, respectively.

Effect of the isoelectric point of pH-responsive lignin-based amphoteric surfactant on the enzymatic hydrolysis of lignocellulose

The isoelectric point (pI) of lignin-based surfactant is an important factor in the enhancement on the enzymatic hydrolysis of lignocellulose. In this work, lignin carboxylate (LC) and quaternary ammonium lignin carboxylates (LCQ-x, x%: the mass ratio of quaternizing agent to enzymatic hydrolysis lignin) with different isoelectric points were synthesized. LC or LCQ-x with pI significantly lower or higher than 4.8 reduced the non-productive adsorption of cellulase on lignin, but for the significant inhibitory effect on cellulase activity, their enhancements on the enzymatic hydrolysis of lignocellulose were not remarkable. However, LCQ-x with pI around 4.8 preserved the cellulase activity, and significantly reduced the non-productive adsorption of cellulase, therefore remarkably enhanced the enzymatic hydrolysis. 2 g/L LC, LCQ-40 (pI = 5.0) and LCQ-100 (pI = 9.2) increased the enzymatic digestibility of pretreated eucalyptus from 35.2% to 53.4%, 95.3% and 60.4% respectively. In addition, for the excellent pH-response performance, LCQ could be efficiently recovered after enzymatic saccharification.

Influence of sulfur dioxide-ethanol-water pretreatment on the physicochemical properties and enzymatic digestibility of bamboo residues

SO₂-ethanol-water (SEW) is a promising pretreatment for improving enzymatic digestibility of biomass through simultaneously removing hemicellulose and lignin. In this work, SEW pretreatment was performed at different cooking times (10 min-60 min) and different SO₂ concentrations (0.5%-2%) to produce pretreated bamboo residues for enzymatic hydrolysis. Meanwhile, physicochemical features of the residual cellulose and lignin were analyzed to better understand how SEW improves enzymatic digestibility. Under optimized SEW pretreatment condition (1% SO₂ concentration, 150 °C, 60 min), 81.7% of xylan and 80.3% of lignin were solubilized, along with 89.1% of cellulose preserved in pretreated solid. A good enzymatic digestibility (80.4%) was achieved at optimum SEW condition. Several compelling correlations (R² > 0.7) were observable between enzymatic digestibility and physicochemical features, demonstrating the importance of SEW pretreatment abilities of hemicellulose and lignin removal, reducing cellulose's degree of polymerization, and improving the amount of sulfonyl groups imparted to the original lignin structure.

Stimulation and inhibition of enzymatic hydrolysis by organosolv lignins as determined by zeta potential and hydrophobicity

BACKGROUND

Lignin typically inhibits enzymatic hydrolysis of cellulosic biomass, but certain organosolv lignins or lignosulfonates enhance enzymatic hydrolysis. The hydrophobic and electrostatic interactions between lignin and cellulases play critical roles in the enzymatic hydrolysis process. However, how to incorporate these two interactions into the consideration of lignin effects has not been investigated.

RESULTS

We examined the physicochemical properties and the structures of ethanol organosolv lignins (EOL) from hardwood and softwood and ascertained the association between lignin properties and their inhibitory and stimulatory effects on enzymatic hydrolysis. The zeta potential and hydrophobicity of EOL lignin samples, isolated from organosolv pretreatment of cottonwood (CW), black willow (BW), aspen (AS), eucalyptus (EH), and loblolly pine (LP), were determined and correlated with their effects on enzymatic hydrolysis of Avicel. EOLs from CW, BW, and AS improved the 72 h hydrolysis yield by 8-12%, while EOLs from EH and LP decreased the 72 h hydrolysis yield by 6 and 16%, respectively. The results showed a strong correlation between the 72 h hydrolysis yield with hydrophobicity and zeta potential. The correlation indicated that the hydrophobicity of EOL had a negative effect and the negative zeta potential of EOL had a positive effect. HSQC NMR spectra showed that β-O-4 linkages in lignin react with ethanol to form an α-ethoxylated β-O-4' substructure (A') during organosolv pretreatment. Considerable amounts of C_2,6-H_2,6 correlation in p-hydroxybenzoate (PB) units were observed for EOL-CW, EOL-BW, and EOL-AS, but not for EOL-EH and EOL-LP.

CONCLUSIONS

This study revealed that the effect of lignin on enzymatic hydrolysis is a function of both hydrophobic interactions and electrostatic repulsions. The lignin inhibition is controlled by lignin hydrophobicity and the lignin stimulation is governed by the negative zeta potential. The net effect of lignin depends on the combined influence of hydrophobicity and zeta potential. This study has potential implications in biomass pretreatment for the reduction of lignin inhibition by increasing lignin negative zeta potential and decreasing hydrophobicity.

Using polyvinylpyrrolidone to enhance the enzymatic hydrolysis of lignocelluloses by reducing the cellulase non-productive adsorption on lignin

Polyvinylpyrrolidone (PVP) is an antifouling polymer to resist the adsorption of protein on solid surface. Effects of PVP on the enzymatic hydrolysis of pretreated lignocelluloses and its mechanism were studied. Adding 1g/L of PVP8000, the enzymatic digestibility of eucalyptus pretreated by dilute acid (Eu-DA) was increased from 28.9% to 73.4%, which is stronger than the classic additives, such as PEG, Tween and bovine serum albumin. Compared with PEG4600, the adsorption of PVP8000 on lignin was larger, and the adsorption layer was more stable and hydrophilic. Therefore, PVP8000 reduced 73.1% of the cellulase non-productive adsorption on lignin and enhanced the enzymatic hydrolysis of lignocelluloses greatly.

Understanding the structural and chemical changes of plant biomass following steam explosion pretreatment

BACKGROUND

Biorefining of lignocellulosic biomass has become one of the most valuable alternatives for the production of multi-products such as biofuels. Pretreatment is a prerequisite to increase the enzymatic conversion of the recalcitrant lignocellulose. However, there is still considerable debate regarding the key features of biomass impacting the cellulase accessibility. In this study, we evaluate the structural and chemical features of three different representative biomasses (Miscanthus × giganteus, poplar and wheat straw), before and after steam explosion pretreatment at increasing severities, by monitoring chemical analysis, SEM, FTIR and 2D NMR.

RESULTS

Regardless the biomass type, combined steam explosion pretreatment with dilute sulfuric acid impregnation resulted in significant improvement of the cellulose conversion. Chemical analyses revealed that the pretreatment selectively degraded the hemicellulosic fraction and associated cross-linking ferulic acids. As a result, the pretreated residues contained mostly cellulosic glucose and lignin. In addition, the pretreatment directly affected the cellulose crystallinity but these variations were dependent upon the biomass type. Important chemical modifications also occurred in lignin since the β-O-4' aryl-ether linkages were found to be homolytically cleaved, followed by some recoupling/recondensation to β-β' and β-5' linkages, regardless the biomass type. Finally, 2D NMR analysis of the whole biomass showed that the pretreatment preferentially degraded the syringyl-type lignin fractions in miscanthus and wheat straw while it was not affected in the pretreated poplar samples.

CONCLUSIONS

Our findings provide an enhanced understanding of parameters impacting biomass recalcitrance, which can be easily generalized to both woody and non-woody biomass species. Results indeed suggest that the hemicellulose removal accompanied by the significant reduction in the cross-linking phenolic acids and the redistribution of lignin are strongly correlated with the enzymatic saccharification, by loosening the cell wall structure thus allowing easier cellulase accessibility. By contrast, we have shown that the changes in the syringyl/guaiacyl ratio and the cellulose crystallinity do not seem to be relevant factors in assessing the enzymatic digestibility. Some biomass type-dependent and easily measurable FTIR factors are highly correlated to saccharification.

Current Understanding of the Correlation of Lignin Structure with Biomass Recalcitrance

Lignin, a complex aromatic polymer in terrestrial plants, contributes significantly to biomass recalcitrance to microbial and/or enzymatic deconstruction. To reduce biomass recalcitrance, substantial endeavors have been exerted on pretreatment and lignin engineering in the past few decades. Lignin removal and/or alteration of lignin structure have been shown to result in reduced biomass recalcitrance with improved cell wall digestibility. While high lignin content is usually a barrier to a cost-efficient application of bioresources to biofuels, the direct correlation of lignin structure and its concomitant properties with biomass remains unclear due to the complexity of cell wall and lignin structure. Advancement in application of biorefinery to production of biofuels, chemicals, and bio-derived materials necessitates a fundamental understanding of the relationship of lignin structure and biomass recalcitrance. In this mini-review, we focus on recent investigations on the influence of lignin chemical properties on bioprocessability-pretreatment and enzymatic hydrolysis of biomass. Specifically, lignin-enzyme interactions and the effects of lignin compositional units, hydroxycinnamates, and lignin functional groups on biomass recalcitrance have been highlighted, which will be useful not only in addressing biomass recalcitrance but also in deploying renewable lignocelluloses efficiently.

Effect of alkali lignins with different molecular weights from alkali pretreated rice straw hydrolyzate on enzymatic hydrolysis

This study investigated the effect of alkali lignins with different molecular weights on enzymatic hydrolysis of lignocellulose. Different alkali lignins fractions, which were obtained from cascade ultrafiltration, were added into the dilute acid pretreated (DAP) and alkali pretreated (AP) rice straws respectively during enzymatic hydrolysis. The results showed that the addition of alkali lignins enhanced the hydrolysis and the enhancement for hydrolysis increased with increasing molecular weights of alkali lignins, with maximum enhancement being 28.69% for DAP and 20.05% for AP, respectively. The enhancement was partly attributed to the improved cellulase activity, and filter paper activity increased by 18.03% when adding lignin with highest molecular weight. It was found that the enhancement of enzymatic hydrolysis was correlated with the adsorption affinity of cellulase on alkali lignins, and the difference in surface charge and hydrophobicity of alkali lignins were responsible for the difference in affinity between cellulase and lignins.

High glucose recovery from direct enzymatic hydrolysis of bisulfite-pretreatment on non-detoxified furfural residues

This study reports four schemes to pretreat wet furfural residues (FRs) with sodium bisulfite for production of fermentable sugar. The results showed that non-detoxified FRs (pH 2-3) had great potential to lower the cost of bioconversion. The optimal process was that unwashed FRs were first pretreated with bisulfite, and the whole slurry was then directly used for enzymatic hydrolysis. A maximum glucose yield of 99.4% was achieved from substrates pretreated with 0.1 g NaHSO3/g dry substrate (DS), at a relatively low temperature of 100 °C for 3 h. Compared with raw material, enzymatic hydrolysis at a high-solid of 16.5% (w/w) specifically showed more excellent performance with bisulfite treated FRs. Direct bisulfite pretreatment improved the accessibility of substrates and the total glucose recovery. Lignosulfonate in the non-detoxified slurry decreased the non-productive adsorption of cellulase on the substrate, thus improving enzymatic hydrolysis.

Lignin degradation in corn stalk by combined method of H2O2 hydrolysis and Aspergillus oryzae CGMCC5992 liquid-state fermentation

BACKGROUND

Lignin peroxidase (LiP) is the primary enzyme responsible for lignin degradation. In our previous work, in order to shorten the pretreatment time and increase the lignin degradation, we have pretreated the corn stalk (CS) using a combination of Aspergillus oryzae CGMCC 5992 solid-state fermentation and H2O2 treatment.

RESULTS

In the present study, one-factor-at-a-time design and response surface design were applied to optimize the nutritional constituents for LiP production in liquid-state fermentation by A. oryzae CGMCC 5992 and the conditions for CS degradation by A. oryzae CGMCC 5992. The optimal medium included CS of 30 g/L, glucose of 4.6 g/L, sodium nitrate of 1.2 g/L, corn steep liquor of 1 g/L, yeast extract of 1.2 g/L, and vitamin B1 of 0.15 g/L. Under these optimal conditions, the LiP production reached its maximum of 652.34 U/L. The optimal condition for CS degradation included CS of 20 g, A. oryzae CGMCC 5992 broth of 50 mL, 1.5 % H2O2 solution of 80 mL, H2O2 flow rate of 0.4 mL/min, water volume of 240 mL (water/material ratio of 12:1), hydrolysis temperature of 39 °C, and hydrolysis time of 8 h. Before hydrolysis, CS and water were pretreated at 113 °C for 11 min. Under these optimal conditions, the sugar yield reached its maximum of 46.28 %.

CONCLUSIONS

Our newly developed method had great advantages in pretreatment of CS due to its quickness, convenience, safety, no special equipment and high sugar yield.Graphical abstractThe schematic diagram of corn straw hydrolysis.